Search Documents

By W. H. Cheung

Nickel and cobalt production relies heavily on the processing of nickel laterite ores; these ores contain the majority of known Ni and Co reserves, 80% and 90% ~ 95%, respectively. The Caron process is used to extract Ni and Co metals from low-grade nickel laterite ores (1% Ni and 0.1% Co). It involves selective reduction of NiO and CoO minerals followed by ammoniacal leaching. Despite low metal recoveries, this process continues to be technically and economically reliable and thus commercially important globally. However, keeping the Caron process cost-effective has been a challenge for industries because of increasing economic and environmental pressures. Although studies of the Caron process have been extensive, significant improvements in recoveries of industrial processes have not been forthcoming. Reported industrial metal recovery from high iron content ore is only 80% ~ 85% for Ni and only 40% ~ 45% for Co; recovery is even lower for ores rich in magnesium. The real difficulty here is that there is no complete understanding of and control over the complex series of reactions in the ore and in the leaching solution during processing. Achieving effective metal recoveries from the Caron will require control of the mineral transformations, which affect the activation of minerals by reduction. In this study, the effect of over-reduction was investigated, which superseded the effect of activation by lowering the activity of the minerals and thus metal dissolution. Reduction was carried out in a batch reduction apparatus with 1:1 and 1:2.5 CO/CO2 gas mixtures from temperatures of 500 ~ 700°C and residence times up to 60 minutes. The pre-reduced ores were leached using a standard ammoniacal leaching test. Thermodynamic analysis and possible effects of stable phase field on leaching was examined. The results suggest that control of over reduction effects are directly related to the mineral transformation and reduction conditions.

Jan 1, 2014

By Kenneth L. Driggs

The 1988 shift in primary smelting facilities from low grade matte (35%) reverberatory furnaces to high grade matte (63%) flash smelting heavily impacted a very stable and successful converter operation. Low matte grade converter campaigns averaged 36,000 short tons of copper and revert production/consumption was in balance. The conversion to high matte grades necessitated oxygen enrichment of converter blast and revisions in operating practices. After two years of operational development, campaign life has risen to over 40,000 short tons and revert production/consumption is again in balance.

Jan 1, 1991

By H. C. Miller

The success of any project in which gas is injected into oil-producing sands to increase the current rate or the economic ultimate production of oil or in which surplus gas from oil producing operations is stored temporarily in reservoir sands that have been wholly or partly depleted of their producible oil depends mainly upon an understanding of the underground movements of oil, water, and injected gas and the ability to control their speed and direction of migration through the reservoir sands. Many operators believe that injected gas always travels up the structure and drives oil to wells structurally higher than the injection wells, because the specific gravity of the injected gas is less than that of the fluid substances in the formation. Consequently, many injection wells are located on the flanks of oil-bearing structures with the idea of utilizing the energy of the injected gas to drive the oil to producing wells higher on the structure. It is true, under certain conditions of pressure and fluid depletion of the reservoir sands, that injected gas will move in an up-structure direction, but the theory that injected gas always moves up the structure is based on an erroneous conception of the laws that pertain to the expansion of gases. By definition, "a gas is distinguished by its property of infinite expansion and is limited in volume only by the walls of the vessel which contains it."3 The expansion of gas that is injected into reservoir sands also is limited by "walls" that surround the space influenced by the injected gas. The walls of the majority of undrilled or virgin oil-bearing reservoirs in California are the impervious shales overlying and underlying the productive strata and the "dams" or effective barriers of edge water around the rims of the reservoirs. When gas is injected into the sands of a producing reservoir, regardless of the location of the injection well on the structure or the degree of depletion of oil from the sands, one of the walls which confine the gas in the structure about the injection well is fluid. This wall will be edge water in a nearly depleted reservoir, where the drainage cones or regions of reduced pressure about injection and producing wells intersect; and, where there is no interference of drainage cones and the injection well is structurally above the edge water, the wall will be oil. In some producing reservoirs bottom water may be the lower wall of the space that confines the gas about injection wells, but the effect of bottom water on limiting the expansion of gas is the same as if the water was not present and impervious formation separated the producing from the underlying nonproducing strata. Therefore, since compressed gas always seeks regions of reduced pressure and its final volume is limited only by formation and fluid barriers and since the force exerted by the gas under pressure is equal in all directions, the course of migration of injected gas in reservoir sands in California and the

Jan 1, 1932

By P. Valicek

Anglo American Platinum Limited is constantly striving to improve safety and productivity. There are many different initiatives taking place within the organization in order to ensure continued safe operation and profitable ounces for the future. One of the opportunities and potential growth areas that has been identified and is being explored is that of mechanization. In order to do this, the approach that has been adopted by Anglo American Platinum is to fully understand and analyse the current mechanized mining methods. Once each configuration is fully understood, the method can then be optimized and new mining technologies and systems can be developed to overcome the current shortfalls. This paper will discuss a methodology that was developed by Anglo American Platinum (in conjunction with Cyest Corporation) and adopted to optimize the mechanized mining layout and fleet configuration, and will also present the final findings of the study. Due to the impracticability of piloting every possible option in the workplace, extensive modelling and simulation exercises were conducted to determine realistic parameters for productivity and value. The study resulted in a full understanding of mechanized mining systems and their associated layout. From the results of the study a mining / logistic layout was developed which highlighted the following opportunities: 1. Create safe operations through the reduction of personnel in the ?high-risk zone? of stopes 2. Separate machines and personnel by use of remotely operated machines 3. Create focused mining on primary development from the production stoping, thus having dedicated teams on development and stoping. 4. Develop primary development ahead of the stoping activity. This enables: a) Understanding of the geology and subsequent implementation of the correct b) technology (?fit-for-purpose?) required to mine that area based upon this geological knowledge c) Ability to install tipping points ahead of stoping, creating ?immediate stoping reserves?, thus increasing flexibility and reducing production risk d) Improved productivity by having adequate faces available and reduction in re-development to establish faces. 5. Quicker return on Investment due to recovering revenue from ?on-reef development? 6. The layout allows flexibility between stope sections enabling better ?resource sharing? 7. Optimize the long-term ratio of machine makeup of the fleet in relation to the production outputs 8. Creates an agile mining layout allowing rapid response to market pressures. The findings and work presented in this paper is currently being implemented at different test sites within Anglo American Platinum and will demonstrate that improved safety and productivity can be achieved through the adoption of mechanization.

Jan 1, 2012

By R. S. Dean

The function of the Metallurgical Division is to conduct investigations relating to the treatment of mineral products from the state in which they are mined to the refined metal or other unfabricated product. These investigations include scientific and practical studies of ore dressing, covering the crushing and grinding of ores, separation by gravity, flotation, and magnetic methods; the hydrometallurgical treatment of ores, including cyanidation and amalgamation of the precious metals; the smelting and refining of copper, lead, and zinc, as well as the rare metals; and steel-melting practices from the raw ore to the finished steel. The object of this work is to conserve natural resources and eliminate waste by furnishing information on current methods of metallurgical practice, making fundamental studies of metallurgical processes, and developing new processes to the point of demonstrating their practicability. The Division is made up of sections devoted to the several phases of this work, each section being beaded by an investigator capable of supervising his particular work. The work is carried on at the experiment stations and field offices or in the field, whichever seems test suited for the work in hand. The following projects should be mentioned as particularly outstanding among those consummated successfully during the year: 1. Application of the type of chemicals known in the textile industry as wetting-out agents to flotation and agglomeration of ores, particulary soluble salts such as sodium and potassium chloride which must be treated in saturated brine. 2. Demonstration of a linear relation between surface and coercive force in magnetic minerals and its application to magnetic separation and to the determination of grinding efficiencies and other metallurgical data which require surface determination at very fine sizes. 3. Pilot-plant demonstration of the practicability of the reduction of iron ore by natural gas and conversion of this direct iron into steel by direct melting and by forging and rolling before melting. The structure and properties of the iron so produced were studied in detail. This report covers the fiscal year July 1, 1934, to June 30, 193b.

Jan 1, 1936

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of 4 foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with MSHA’s lower coal mine respirable dust standard (1.5 mg/m3). Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used a low pressure air generated by a blower and water pressure using a NIOSH developed foam generator. Foam property tests comprising of a bottle shake test, foam expansion ratio, and water drainage were used to classify foams. The bottle shake tests determined that the lowest concentration of foam agent to be used was approximately 1.5%. Compressed air generated foams tended to have low expansion ratios (10-19) with high water drainage. Blower air generated foams had higher foam expansion ratios (30-60) with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The different foam agents produce foams with different material properties. Results of testing eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents, while having different foam properties, seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. INTRODUCTION About one-half of U.S. underground coal is produced by longwall mining. This technique allows for mining high volumes of coal, producing significant amounts of coal mine dust. This can lead to the overexposures to longwall miners and possibly occupational respiratory diseases black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [1]. When respirable quartz is present, the mine must maintain an average concentration at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present [2]. Respirable dust samples collected by U.S. Mine Safety and Health Administration inspectors for the five-year period from 2010 to 2014 found that 5.6% (53 of 943 respirable coal mine dust samples) of the longwall operators on the tailgate side exceeded the coal mine dust standard, and 4.3% (76 of 1768 samples) of the jacksetters exceeded the standard. If silica is present, the reduced standard is implemented, meaning that 11.4% (36 of 316 respirable coal mine samples analyzed for dust) of the jacksetters exceeded the reduced standard. Only 3.8% (18 of 478 samples) of the longwall operators on the tailgate side exceeded the reduced standard [3]. Had the 1.5 mg/m3 standard been in effect during this period, non-compliant samples would have been much higher. For example, over 15% of the samples collected at the tailgate shearer operator occupation exceeded the lower standard."

Jan 1, 2017

By B. S. Terry

Experiments have been conducted to assess the feasibility of capturing bearing emissions arsenic with CaO during the roasting of enargite (Cu3AsS4). Enargite/CaO mixtures have been heat treated in air, nitrogen or oxygen for various times and the products of reaction analysed by X-ray diffraction and cleaned analysis. The results show that substantial capture of arsenic can be achieved via the formation of calcium arsenates and/or calcium arsenides. In addition significant capture of sulphur is achieved by the formation of calcium sulphate andlor sulphide. Complete conversion to copper sulphide with total removal of arsenic can be achieved within 30 minutes at 700°C. Further heat treatment in air or oxygen leads to the formation of copper oxide and copper oxysulphate. Without optimisation of reaction conditions, it has proved possible to achieve retention of in excess of 85% of the arsenic content of enargite in the form of calcium arsenates.

Jan 1, 1994

By G. E. McElroy, D. Harrington

The use of shall electrically- driven fans , in conjunction with air- pipe of various diameters is becoming of increasing importance for the ventilation of working places in metal mines through which the general ventilating currents can not be coursed . It will probably continue to increase in importance since the concept that air motion is the most important factor in maintaining comfort in hot ( above 80° F . ) working places is more generally accepted , and as the inefficiency and greater expense of attempting to ventilate such places with compressed air is recognized . Managers of large properties can afford to experiment with fan- pipe installations until types are found that meet their conditions , but managers of shall properties , unless forced to it by extreme conditions , prefer to wait until they can obtain data sufficient to guarantee at least a measure of success from such installations . At present , such data , even in part , are available to only a few (mainly fan manufacturer's representatives , consulting ventilation engineers , and ventilatin engineers employed by large companies ) , and important recent developments are mostly of a confidential nature . One large metal - mining company cooperated with a fan manufacturer in some extensive experimental work on small blowers and found that instead of using stock fans , considerable power economy could be effected and equal quantities of air delivered by use of or 2/3 width fans with small motors rather than using stock fans and larger motors ; it was also found advisable to adopt certain sizes of tubing for certain lengths of run . In fact , many important facts were ascertained in this study , and it is now promised that they will soon be given to the public . It is true that a certain amount of data on industrial installations are available , but such data are only in part applicable to metal -mine conditions , because , until recently , little attention has been given to ventilation in metalmines , and the conditions encountered usually require a greater length of pipe , a more temporary type of construction , and closer attention to temperature control than the ordinary run of industrial installations demands ..

Feb 1, 1922

By Malti Goel

"Ferrous and non-ferrous metals industries are source of both direct and indirect greenhouse gas (GHG) emissions. Metal industry accounted for 29.7% of the total GHG emitted from the Indian industry sector in 2007. Aluminum is second largest contributor after steel. Indian Aluminum industry has been growing and is adopting several effective measures for better efficiencies through process change and waste utilization. Improvement in the energy efficiency can form the basis of monitoring reduction in emissions. Under the National Action Plan on Climate Change 2008, National Mission for Enhanced Energy Efficiency (NMEEE) aims to upscale the efforts to unlock the market for energy efficiency improvement on a public private partnership (PPP) basis. For a transition to low carbon economy industry is undertaking voluntary measures through scientific and technological innovations both in upstream and downstream sectors. In this paper an attempt is made to overview recent developments in Indian Aluminum industry as well as summarize scientific & technological challenges and prospects.IntroductionAluminum plays a vital role in industrial development. It is a substitute for different type of materials ranging from wood to copper and steel. The aluminum industry has high energy consumption and high contribution to greenhouse gases from carbon dioxide and perfluorocarbons (PFCs) emissions. It is estimated that CO2 equivalent burden of aluminum industry is about 1% of total anthropogenic emissions. The anticipated world growth rate is 3.5% for aluminum demand. Through measures to reduce both direct and indirect CO2 emissions, electricity consumption was reduced from 25 kWh / kg of Aluminum in 1998 to 15 kWh / kg of Aluminum produced in 2008. It is targeted to further reduce it to 10.8 kWh. Aluminum industry is also responsible to about 60% of all PFC emissions. The PFC emissions are harmful to environment, accumulate in surrounding vegetation and contaminate. Efforts to reduce PFC emissions from aluminum industry started early and reduced to 0.5-1 kg / tonne in 1990 [1] from 12-15 kg / tonne in 1940. Since 1990s to 2000 it further reduced to 0.2 -0.4 kg / tonne as seen in Fig. 1. The Global Aluminum Sustainable Development Initiative (GADSI), targets perfluorocarbon (PFC) specific emissions reduction of 80% for 2010 relative to 1990."

Jan 1, 2011

By A. J. Petrina

"At Craigmont Mines Limited, Merritt, B.C., tests were begun in March, 1965 to evaluate the use of shotcrete as a method of ground support m development headings; previously, ail drifts had. required support, which was accomplished mainly by timber and occasionally by the use of rockbolts. The tests demonstrated conclusively the effectiveness of shotcrete for supporting Craigmont's ground. Gradually, the use of timber for ground support was virtually eliminated in favour of shotcrete. This paper describes the equipment used, the operation of the equipment, pertinent cast data and opera ting details. Also discussed are other uses developed for the shot-creting equipment, the use of reinforcing bar rockbolts, and a method used at Craigmont for lining long vertical ore passes with steel plate and concrete as part of the raising cycle."

Jan 1, 1968

By W Malone, J Garrett

FLSmidth (FLS) has spent the last 15 years, working with customers and engineering houses to deliver innovative improvements in crusher safety, coupled with the latest, maintenance friendly, crusher design. The key focus being to prevent service personnel from working underneath the crusher during maintenance and obviate the need for personnel to be exposed to suspended loads when performing tasks such as, main shaft installation, for example. Improvements include: full top-service capability to ensure the safest and fastest way to disassemble the crusher for maintenance purposes, which also removes the requirement for a service cart; a selfaligning main shaft which ensures remote assembly is now possible, keeping service personnel well out of harm’s way; And rotable shells, or the ability to perform relines off-station, allows for quick shell ‘swap-over’ without the downtime associated with removing, refitting and curing time associated with epoxy backing. The high flow spider improves large material entry into the crusher, reducing blockages and downtime and therefore maintains crusher capacity. Each size of crusher in the range comes with an option to increase the standard feed opening to a larger one if desired to compensate for ‘blocky’ or ‘elongated’ feed material, a common problem for Pilbara hematite iron ores. Power capability has also been increased with a maximum of 1500 kW, to match the higher throughput capacities being achieved. This due to uprated eccentric speeds and larger discharge annulus. Increased eccentric throws and mantle diameters are also now a reality, when compared to more traditional designed gyratory crushers. To keep up with the improved design features of the Mk V, digitalisation has also been upgraded to maximise performance capabilities to ensure that the most efficient reduction and throughput capacities are achieved, whilst utilising the higher powers now available as standard. Condition monitoring ensures that the crusher is at its optimum operating capability by monitoring and adjusting the crusher settings via feedback from additional sensors, ie main shaft spin, temperature and vibration. Camera monitoring capabilities are available as is an advanced oil contamination monitoring system. As a result of the above design improvements, it will be shown that the Mk V range offers benefits such as: enhanced safety features, increased availability, faster maintenance turnarounds, higher power utilisation, equivalent product size at higher throughput capacities and with Remote operation capabilities. All of which result in a gyratory crusher with higher levels of safety and a lower per tonne operating cost.

Sep 18, 2023

By O. A. Bascur

In recent years, metal-producing companies have increased their investment in automation and technological innovation, embracing new opportunities to enable transformational change. Transformation to a digital plant can fundamentally revolutionize how industrial complexes operate. The abundant and growing quantity of real-time data and events collected in the grinding and flotation circuits in a mineral processing plant can be used to solve operational issues and optimize plant performance. A grade recovery model is used to identify the best operating conditions in real time. The strategy for increasing the value of instrumentation in current plants is reviewed. An optimal Gaudin size distribution model provides augmented information from traditional sensors to find the optimal grind cut size to reduce metal losses in the flotation circuits. Sensors in flotation circuits enable an estimate of the recovery and determination of the optimal froth depth and aeration using an air hold up flotation model. A strategy of classifying data for on-line generation of insights to using operational intelligence tools is described. The implementation of a recovery/grind strategy with industrial examples in non-ferrous mineral processing is presented.

By Gerhard Meyer

A new instrument for the determination of iron., zinc, calcium, and other metals independently directly in the fumes emitted from steelmaking processes is described. Based on the well- accepted method of X-ray fluorescence, the instrument can detect numerous metals simultaneously in the fume as well as report their concentration on a mass per unit time basis real time to a control room computer. The instrument mounts on the wall of the fume duct and can., via a small opening, directly view the hot exhaust plum inside the duct. The concentration of metal in the fume over time has been shown to change dramatically depending on process variables. Variables such as oxygen flow rate, lance height and nozzle configuration., slag condition., and episodic scrap addition can affect the presence of metal particles and fume in the exhaust. An analysis response time of 6 seconds enables better control of the steelmaking process thereby conserving primary resources and reducing environmental impact.

Jan 1, 2001

By R. S. Dean

The function of the Metallurgical Division is to conduct investigations relating to the treatment of mineral products from the state in which they are mined to the refined metal or other unfabricated product. These investigations include scientific and practical studies of ore dressing, covering the crushing and grinding of ores, separation by gravity, flotation. and magnetic methods; the hydrometallurgical treatment of ores, including cyanidation and amalgamation of the precious metals; the smelting and refining of copper, lead, and zinc, as well as the rare metals; and steel-melting practices from the raw ore to the finished steel. The object of this work is to conserve natural resources and eliminate waste by furnishing information on current methods of metallurgical practice. making fundamental studies of metallurgical processes, and developing new processes to the point of demonstrating their practicability. The Division is made up of sections devoted to the several phases of this work, each section being headed by an investigator capable of supervising his particular work. The work is carried on at the experiment stations and field offices or in the field, whichever seems best suited for the work in hand. The following, projects should be mentioned as particularly outstanding among those consummated successfully during the year: 1. Application of the type of chemicals known in the textile industry as wetting-out agents to flotation and agglomeration of ores, particulary soluble salts such as sodium and potassium chloride which must be treated in saturated brine. 2. Demonstration or a linear relation between surface and coercive force in magnetic minerals and Its application to magnetic separation and to the determination of grinding efficiencies and other metallurgical data which require surface determination at very fine sizes. 3. Pilot-plant demonstration of the practicability of the reduction of iron ore by natural gas and conversion of this direct iron into steel by direct melting and by forging and rolling before melting. The structure and properties of the iron so produced were studied in detail. This report covers the fiscal year July 1. 1934, to June 30, 1935.

Jan 1, 1936

By B Washington, A Campbell, R Taylor

A sampling and measurement program was undertaken on the reaction shaft of the Olympic Dam copper flash smelting furnace. The object of the work was to provide information to validate a mathematical model of the burner and reaction shaft. Samples and measurements were undertaken through the burner inspection ports and the South East (SE) shaft sampling port about half way down the reaction shaft. Samples were collected to enable the calculation of particle loading of shaft gases, or sizing and chemical analysis of the partly-combusted feed, and the preparation of polished sections. Measurements were made of the temperature and sulfur dioxide content of the atmosphere, as well as plume velocity.To implement the program it was necessary to design and construct the following specialised items of equipment. For use at the burner inspection ports: a cup sampler for obtaining samples below the burners (temperature, solids loading and samples for characterisation).For use at the SE shaft sampling port and also at the settler level: trough sampler (plume definition and samples), isokinetic sampler (used as a velocity probe in this work), temperature probe (temperature traverses across the shaft), and sulfur dioxide probe (SO2 measurements across the shaft).The design of the sampling and measuring equipment is described, and examples are cited of the types of information obtained. The problems arising from working in a hot environment with molten or sticky particles are discussed.

Jan 1, 2005

By Charles D. Walcott

Jan 1, 1901

By Henry Wurtz

Jan 1, 1880

By Robert H. Ridgway

This circular outlines salient facts regarding the pyrites industry of the United States and the world. It is founded chiefly upon published information available in the literature of the subject. The United States Bureau of Mines has in its files additional and more detailed data upon many of the subjects presented very briefly here, and will endeavor to assist the mineral industries and the public by giving further information in response to individual inquiries. The bureau will welcome comments, criticisms, and contribu- tions of data that may assist in making later editions of this circular of information more accurate, or may aid in developing more fully the files pertaining to pyrites.

Sep 1, 1931

Any Australian who knows of the poverty of the early settlers in the first few years following the arrival of Captain Arthur Phillip with his "first fleet" at Botany Bay must feel proud of the progress that has been made in the 174 years that have elapsed since that momentous occasionGFor all its attractive appearance as reported by Captain Cook and Sir Joseph Banks, the shores of Botany Bay and of Port Jackson proved most ,inhospitable, and the accessible country surrounding them anything but suitable for sustaining the life of the small settlement. It is well known that during the first 15 or 20 years the hardy colonists and un-tfortunate convicts were close to starvation on several occasions and were only saved by the arrival of supply ships, which were dependent on the vagaries of wind and current, and the hazards of the uncharted seas they had to -navigate-.When Australia was little more than a miserable penal settlement, Great Britain was one of the great-powers of the world, and the U,.S.A. was an independent nation with a growing degree of prosperity that even then gave promise of its mighty awakening to become, as it has, a e.olossus of industry and commerce,-and the. leader in living standards of the world to-day.Australia, from such a shaky, and comparatively recent start, has risen to a position in which its living standards rank very high in comparison with those of most of the nations of Europe and America. Exact com-parisons are hard to fix because of the wide variety of factors involved .but the Institute of Pab?Lic Affairs .(Victoria) places Australia fifthin the world, excelled only by the U.S.A., Canada, Sweden and Switzerland. The next best after Australia are the United Kingdom, West Germany and France.How we achieved such a high standard of living is a vast subject for study but some of the economic aspects of our climb from abject poverty to a position of near affluence can readily be identified.

Jan 1, 1962

By M. J. Ferrante

Relative enthalpies of V20S from 298.15 to 1,101.0 K were measured at the Bureau of Mines to provide data needed for the advancement of min-eral technology. Enthalpies were measured with a copper-block calorimeter. A sharp melting point was found at 951 K, with [~~ = 15.690 kcal/ mol ] for the standard enthalpy of melting. Tabulated values are given at selected temperature increments between 298.15 and 1,500 K for the standard relative enthalpy [(HO -H~98),] heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)/T]. Standard relative enthal-pies are also given in equation form and combined with data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation.

Jan 1, 1986