Search Documents

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968

By M. W. Von Bernewitz

Corduroy is used for saving gold in small Land large milling plants throughout the world. Investigations by the Metallurgical Division of the Bureau of Mine indicate that corduroy blankets, used with or without a trap or jig in the mill classifier circuit, often are effective in concentrating gold and sulfides, especially if the gold does not amalgamate readily and if not enough sulfides are present to warrant the use of a shaking table, flotation cells, or cyanide plant. Most cold-mining countries include several or many small miner, that produce siliceous ores low in sulfides and gold, which can easily be amalgamated or caught in traps or jigs or on corduroy and shaking tables. At these mines the ore is crushed by stamps or bill mills, and the flow sheets include plates, flotation cells, and cyanide treatment, yet probably nearly as much of the pair minerals may be recovered by the less expensive plant. A well-known western maker of mine and mill equipment asserts, as the result of considerable observation of installed plants, that old and other valuable minerals should be caught as soon as they have been released by a mill, end recommends jigs to do this. A supplier of corduroy has informed us that at some mines this material is being replaced by jigs that catch gold as fine as 400-mesh. But for the small operator, inexpensive equipment such as a corduroy table may be better adapted and give a good recovery of gold and associated minerals.

Jan 1, 1939

By M. R. Fletcher

Slags generated by the ferrous-metals industry can be used to produce high-tech ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted and formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost wear-resistant tile material which can be custom cast. This and similar materials, made from slags and natural rocks, are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1988

When science and the human spirit come together amazing things can happen. This was perhaps never more evident than through the events that unfolded during August and October in a remote desert in northern Chile. On Aug. 5, the main shaft of the San José copper and gold mine near Copiapó in Chile?s Atacama Region collapsed, leaving 33 miners trapped more than 624 m (2,000 ft) beneath the earth?s surface.

Jan 1, 2010

By Ernie M. Crist, Laurentiu Nastac, Frank Spadafora

"This paper describes the modeling techniques and the experimental and computer results for two casting processes that are under development and optimization. These processes are described as follows:1) Electromagnetic stirring (EMS) during casting of Ti-6Al-4V round ingots using the plasma arc cold hearth melting (PAM) process: The purpose of EMS is to establish a singlemelt PAM process capable of consistently producing as-cast ingots without helium porosity and also having no need for surface conditioning prior to secondary processing.. The modeling approach is based on the numerical solution of Maxwell's equations, fluid flow, and heat transfer equations, and mesoscopic modeling of the grain structure.2) Casting of Ti-6Al-4V slabs using the single-melt PAM process: The purpose of slab casting is to improve yield by eliminating an intermediate blooming step for converting round ingots to slabs. The modeling approach is based on the numerical solution of fluid flow and heat transfer equations. The effects of pouring and mold temperatures on the pool and temperature profiles were studied. Also, the torch effects (such as the torch standoff and its traversing path) on the pool and temperature profiles were investigated and the best-case scenario was used in the experiments. Evaluation results at RMI Titanium Company showed that the plates made from the slabs met the mechanical properties and microstructure requirements.Acknowledgment. This work was conducted by the National Center for Excellence in Metalworking Technology (NCEMT) operated by Concurrent Technologies Corporation (CTC) under contract No. N00014-00-C-0544 to the US. Navy as part of the US. Navy Manufacturing Technology Program. Dr. K. b. Yu from RMI and my colleagues from CTC are acknowledged for their comments on this work."

Jan 1, 2004

By Taghi Sharizadeh, MAURICE SUNKPAL, ELAHEH TALEBI, PEDRAM ROGHANCHI

Excessive heat exposure is among the health and safety hazards that have adverse effects on the mine workers. The very nature of the underground climate makes it a convenient avenue for heat generation and accumulation from several heat sources including autocompression, equipment, and heat from strata. This study investigated the effects of clothing insulation and acclimation on the thermal comfort ofmineworkers who are exposed to heat in underground working environments. Several clothing ensembles have been considered to analyze the effect of the thermal resistance of clothing on the thermal comfort of workers. To investigate the impact of the clothing insulation, the thermal comfort limit of an underground miner was calculated in the form of maximum allowable exposure time for an 8-h shift. Parametric analyses were subsequently performed using an already developed thermal comfort model using MATLAB software. The results demonstrate that clothing insulation has a significant effect on the thermal comfort of mine workers. Increase in the clothing insulation decreases the maximum allowable exposure time of mine workers. This is especially true for the new and non-acclimated workers. Since acclimatized workers can tolerate a higher level of the dehydration and are capable of losing more water by sweat per shift, the maximum allowable exposure time for the acclimated workers are higher than non-acclimated workers. These analyses have shown that acclimated workers can have more continuous work per shift compared with non-acclimated workers. For example, in an environmental condition with clothing that a nonacclimated worker cannot work more than 5 h, an acclimated worker can work a full 8-h shift.

Jun 29, 2020

By Djona M. Gaballah I.

Selective chlorination of unroasted and roasted spent hydrorefming catalysts was studied between 300 and 600°C using the following gas mixtures : C12+CO, C12+N2 and CI2+air. Such materials contain Co, Ni and Mo compounds supported by alumina and/ or silica. They also contain variable amounts of V compounds, C, S, etc., accumulated during the life time of the catalyst. Direct oxychlorination of the C+S rich sample allows higher extraction rates than those obtained by the carbochlorination of the same roasted one. It seems that the roasting step doesn't favor the economic metals' recovery. Results of the chlorination of C+S poor spent catalysts, in the presence of CO, in the chlorinating gas mixture, or of carbon added to the sample, were comparable. Cobalt and nickel chlorides were .extracted from the chlorination residues by their dissolution with acidified water, whereas molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The recovery rates of valuable metals as well as the selectivity were higher for the chlorination of spent catalysts than results obtained by the hydrometallurgical processing of the same sample. Results of the scale-up of the oxychlorination of the unroasted sample confirmed those of the laboratory scale. The global recovery rates were about 88 pct of cobalt, 93 pct of molybdenum and 76 pct of vanadium. The carbochlorination was applied to the recovery of W and Ti from Denox catalyst that is a carbon and sulfur free one. Recovery rates higher than 99 pct at temperatures lower than 500 °C could be obtained. This may indicate that the chlorination process can be applied to the treatment of various industrial wastes or by-product containing transition and/or refractory metal compounds A flow - sheet for the pretreatment of these materials is proposed.

Jan 1, 1995

By P. M. Sullivan

At its College Park Metallurgy Research Center in Maryland, the Bureau of Mines has installed and is operating a 5-ton-per-hour pilot plant for continuous mechanical separation of values contained in raw urban refuse. The entire sys tern was assembled using commercially available equipment. The process relies on multistage processing including shredding, air classification, screening, gravity concentration, and electrostatic separation. Compactor trucks deliver raw refuse collected along typical routes in metropolitan Washington, D.C., to the pilot plant. The loads are separated into concentrates of (1) light-gage iron, (2) massive metals, (3) glass, (4) putrescibles and waste combustibles, (5) paper, and (6) plastics. While some refinements remain to be made in the processing system flow-sheet, the data obtained to date have been highly encouraging, indicating favorable economics for commercial-size plants.

Jan 1, 1973

By G. St. J. Perrott, G. W. Jones

"In cooperation with The Edison Electric Illuminating Co. of Boston, Mass., a survey was conducted in 1929 and 1930 by the United States Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes and other underground openings owned by this company. The territory served approximates 650 square miles and includes 46 cities and towns. The transmission and distribution systems are on overhead construction and underground wires and cables run in underground conduits and manholes. There are 17,000 manholes on the system, and also an area in Boston proper served by the Edison tube system. These conduits and manholes are laid in various types of streets from the most modern type of cement roadbed to the older type of loose macadam. The conditions as found could be considered as typical of any public utility in the electric-light and power field. The survey extended over a period of about a year beginning in June, 1929, and ending in July, 1930, and during this time 1,765 different manholes were tested and a total of 4,068 tests were made.Previous to starting the actual survey, one of the writers, G. W. Jones, spent considerable time in Boston determining the best methods of practical· test procedure. In this work cooperation was given by John Campbell, superintendent, special service department, who for a number of years has been making a study of explosions in underground street areas and preventive measures in Boston and various cities.After this preliminary investigation the tests were continued by employees of the Edisun Company. Copies of all records of tests were forwarded to the United States Bureau of Mines Pittsburgh Experiment Station so that the writers were in close touch with the progress of the survey, and changes could be made in the test procedure whenever deemed necessary."

May 1, 1931

By Ray Holmes

This paper describes one approach in our search for greater stope efficiency and lower costs. The uppers technique with wagon drills in cut-and-fill stopes was commenced, on an experimental basis, in our Sudbury mines in 1961. To date, the method has developed into an accept-ed production operation. This technique minimizes the intermittent aspects of the drilling, blasting, mucking and filling operations associated with other cut-and-fill methods. However, studies show that not all cut-and-fill stopes are suitable for uppers, the governing factors being ore width, dip of the orebody, and ground conditions where large areas of unsupported back remain stable for ex-tended periods of time until rockbolting can be accomplished. Introduction F ALCONBRIDGE Nickel Mines Limited operates seven mines within a radius of 30 miles of the city of Sudbury, Ontario. These mines extend in depth from 1,500 to 6,300 ft. The ore consists of brecciated, massive and disseminated sulphides, and the ore minerals consist primarily of pentlandite, pyrrhotite and chalcopyrite. Widths are generally irregular and vary up to 150 ft. The ore dips at between 35 and 90 degrees.

Jan 1, 1965

By William J. Campbell

One of the principal objectives of the Bureau of Mines program for developing super refractory materials is to obtain fundamental data on the physical properties of refractory oxides. This particular investigation obtained accurate thermal expansion coefficients for alpha alumina and evaluated, critically, those coefficients with other published values. High-temperature X-ray diffractometer measurements, by the Bureau, showed that alpha alumina expands anisotropically with expansion parallel to the c axis approximately 10 percent greater than parallel to the a axis. Thermal expansion characteristics of four different alumina samples were determined up to 1,200° C.; the results are presented in both tabular and graphical form. The combined random and systematic errors in the measurements are considered less than 3 percent above 500° C, and approximately 2 percent at 1,000° C. No differences in expansion were observed between the samples or between the heating or cooling cycles.

Jan 1, 1961

By N. S. Dalal, V. Castranova, X. Shi, W. Wrr, V. Vallyathan

"SUMMARY Data presented here indicate that freshly fractured silica exhibits surface characteristics and biologic reactivity distinct from aged silica, and on this basis we propose that these surface features may lead to enhanced manifestations of lung Injury. Grinding of silica produces ~10"" Si and SI-O (silicon-based) radicals per gram of dust on the particulate surface which are characterized by an electron spin resonance (ESR) spectrum centered around g = 2.0015. These silicon-based radicals react with aqueous media to produce OH radicals, which are demonstrable using a DMPO spin trap. The concentration of silicon-based radicals in silica decreases with aging in air and exhibits a half-life of ~30 h, whereas its ability to generate OH radicals in aqueous solution decreases with a half-life of ~20 h. However, on storage in aqueous media, the concentration of silicon-based radicals end the dust's ability to generate OH radicals decrease significantly within a few minutes. Freshly ground silica is also more biologically reactive than aged silica, because freshly crushed silica activates a greater respiratory burst In alveolar macrophages than aged silica, i.e., storage of ground dust in air decreases silica-Induced superoxide anion secretion, hydrogen peroxide release, and NBT reduction by 25%, 68%, and 43%, respectively. Furthermore, compared to aged silica, freshly ground silica exhibits a greater cytotoxic effect on cellular membrane Integrity, i.e., a 1.5-fold increase in LDH release from macrophages, a 36-fold increase in hemolytic activity, and a three-fold increase in the ability to induce lipid peroxidation. Because acute silicosis is frequently associated with occupations in which freshly fractured crystalline silica of respirable size is generated, the present study suggests that fracture-generated silicon-based radicals may play a significant role in the pathogenesis of this disease. AM REV RESPIR DIS 1955; 133:1213-1218IntroductionOccupational exposure to crystalline silica can be associated with either chronic or acute pulmonary disease. Chronic silicosis becomes manifest 20 to 40 years after first exposure and is characterized by development of concentric hyalinized nodular lesions in the lung with the de-velopment of dyspnea over a period of several decades. Acute silicosis, on the other hand, is manifested by a rapid on-set after exposure and is characterized by the accumulation of an amorphous granular lipoprotein exudate in the airspaces and rapid development of respiratory disability within a few years (1-3).Information is growing concerning the etiology of chronic silicosis. Studies sug-gest that several mechanisms may be in-volved in the development of fibrosis. Lung injury may result from silica-induced release of lysosomal enzymes from alveolar macrophages (4, 5). In ad-dition, silica-induced activation of su-peroxide anion and hydrogen peroxide release from alveolar macrophages may result in oxidant-induced damage to lung parenchyma (6). Silica exposure can also result in the release of mediators from alveolar macrophages which enhance the proliferation of fibroblasts and the syn-thesis of collagen by these pneumocytes (7, 8)."

Jan 1, 1988

By Thomas Schanz

Current steel market conditions require small investments only to lower operational cost. SMS Concast has developed new products which optimize continuous casting process cost for long product steel production. This paper describes a selection of three products. All three systems are patented (patent pending for CONDRIVE). CONSAFE, a non-radioactive mould level measurement system for reliable mould level measuring on open stream casting CCM’s; CONSTIR-MWS, an improved control software for electromagnetic stirrers which lowers energy cost by 35%; CONDRIVE, a brand new oscillation drive system which provides the features of a hydraulic oscillator, however with a cost efficient electric drive.

Aug 17, 2017

By B. J. Sauer

Variable frequency drives (VFD’s), or adjustable frequency controls (AFC’s) as they are more precisely identified, have been available to the mining industry for over 20 years. However, in recent years as the push to cut production costs has become ever so crucial, AFC usage has become more widespread. This paper seeks to provide professionals in mineral processing plant design and operation with an introduction to AFC’s, insight as to why AFC control for AC induction motors can be advantageous, and specification and design considerations.

Jan 1, 2002

By Arthur Crowfoot

This paper describing t o concentrating practice of the Phelps Dodge Corporation, Morenci Branch, at Morenci, Ariz., is one of a series of articles on concentrating methods and posts being prepared by the Bureau of Mines. The Morenci concentrator, locally known as No. 6 concentrator, treats 5,000 dry tons of ore per 24-hour day by primary tabling followed by two stages of flotation treatment, at 48-mesh size and 65-mush size respectively.

Jan 1, 1931

By Oliver C. Ralston, Foster Fraas

The electrostatic separation of solids utilizes the forces exerted when electrically charged particles of the solids are present in an electric field . The charges may be acquired by various means (5) , and when the acquisition or loss of charge depends on the property of the particle , separation can be obtained between particles having different properties . A property commonly utilized in present - day separators in conductance . Charging also may be accomplished by bringing the particles into intimate contact with various surfaces . This is sometimes described as a " frictional electrical effect. The charge , or specifically the polarity of the charge , in this latter case evidently depends on the property known as the contact potential , as has been explained in the discussion of a paper (7) and in several other papers (10) . Separation by this method is accomplished in two steps - a charging step , in which the particles are brought into intimate contact with an electrification surface , and a separation step , in which the charged particles are separated in an intense electric field . Descriptions of such methods may be found in the literature (2) , (7) , ( 8) . Even as early as 1909 , Blake and Morscher (2) described the charging of particles by intimate contact followed by separation in an electric field . They also state that the polarity of the electrical charge acquired by the particles depends on their composition . O'Brien ( 8) presented several designs of apparatus . He obtained electrification by means of a wiping action , either on inclined plates or in rotating cups , in which a centrifugal force was imparted to the particles .

Nov 1, 1942

By J. E. Shigley

The gemological properties that allow natural emeralds and blue sapphires to be distinguished from other gemstones are summarized in this paper. A variety of synthetic and laboratory-treated emeralds and blue sapphires are also encountered in the jewelry industry today. Gemologists distinguish these latter materials from their natural counterparts based primarily upon features seen with magnification, such as inclusions and/or growth zoning. In some cases, however, these observations and standard gem-testing methods are insufficient, and the use of non-destructive analytical methods, such as optical spectroscopy and chemical analysis, are required for positive identification. The commercial value of synthetic and treated gems are much less, and can be insignificant in comparison to that of an important untreated natural gemstone. Identification of synthetic and treated gem material is essential to maintaining integrity in the jewelry industry. Loss of consumer confidence in the gemstones sold at the jewelry counter could have a negative impact on the exploration and mining of natural emerald and blue sapphire.

Jan 1, 1998

By James Westfield

I welcome this opportunity to appear before you and to review briefly the various health and safety services of the Bureau of Mines available to the mining industry, other than coal, and also to tell of our plans for extending these services to improve safety and health conditions. The Bureau's health and safety activities are basically services by which we attempt to develop and disseminate information on improved techniques in mine accident prevention and promote mine safety education in the mineral industries. Unfortunately, some mining companies, particularly some of the smaller operations, seem to be unfamiliar with these services, The Bureau of Mines is charged by law with the responsibility for inspecting coal mines; other services to the coal mining industry and are provided only on request, Safety inspections and other services that we offer are provided for noncoal mining industries solely upon request.

Jan 1, 1958

By E. Dernedde

Industrial plants located in the province of Quebec, Canada, are subjected to large variations of the ambient air temperature, Building ventilation systems of these plants must have some flexibility in order to meet industrial hygiene standards (TLV for chemical substances, heat stress and cold stress) at any time of the year, The building ventilation of a bath treatment plant of an aluminium smelter in Quebec was examined under summer and winter conditions, Part of the plant has periodic emissions of hydrogen fluoride gas and heat from hot anode butts, CFD modeling was used to optimise the building ventilation of the bath treatment plant, The present study proposes a modified building ventilation system, which improves the internal environment, complies with industrial hygiene standards and also reduces heating costs by 20 % during winter.

Jan 1, 2005

By John B. Phillips

The mine is entered by a central vertical shaft, strongly timbered, and containing two compartments-one for the passenger cage, the other for the large skips bringing the ore to the surface. A man-way, for emergencies, is also provided, parallel to the shaft. The cage is a single-deck steel box, carrying about thirty persons; by means of arrangements above and below, it can also hoist and lower materials needed in the workings. Levels are run at intervals of 100 feet. In special cases, where the ore conditions warrant, sub-levels are operated, such as those at 1,113 feet and 1,123 feet (Fig. 7), which are connected by winzes with the 11 th level. One of these was pushed for 40 feet, and then abandoned because it was unprofitable to take up ore of the grade encountered. The ore between levels is removed by stoping. The drifts follow the course of the veins as much as possible, with numerous cross-cuts. Winzes, raises, connections, etc., are blasted out where needed. The main drifts are at least 8 ft. high by about 9 ft. wide. All former narrow drifts had to be widened some time ago, by ruling of the Ontario Department of Mines, to lessen the danger of accidents with cars in the small passages. Accurate plans of the under-ground workings are kept in the office, and extensive surveying is always being done underground to keep the maps up to date, measure the cubical contents of stopes, and so forth. Timber is extensively used in the construction of supports and chutes, and in the sinking of the shaft. Steel and concrete are too ex pensive to compete with timber, which 1s abundant in such sections as have escaped forest tires.

Jan 1, 1926