Search Documents

By Ramana G. Reddy, Yudong Li

Numerical modeling of the thermal plasma process was carried out based on the thermal plasma reactor in our lab and confirmed using experimental data. The inlet boundary conditions of a non-transferred DC arc thermal plasma reactor were used in modeling the temperature and fluid flow distribution in the reactor. Different mesh grid sizes were used to confirm the model is independent of grid size. Temperature profile and gas flow distribution in the thermal plasma reactor were developed by the computational fluid dynamics (CFD) with ANSYS Fluent. The predicted temperatures are in good agreement with the experimentally measured temperatures in the reactor. The influence of plasma torch input power as well as the plasma gas flux on the temperature distribution was investigated using this model. The influence of power input and gas flow rate on temperature and velocity distributions are not independent. Generally, higher power input and lower gas flow rate will give rise to the temperature increase in the reactor.

Mar 1, 2017

By Amir Karami, Scott Munro

This paper focuses on remediation of a 3.6 km long water conveyance tunnel that suffered two large falls of ground (FoGs), one of which subsequently progressed to the ground surface, resulting in full collapse of the tunnel. The tunnel is part of a network of water conveyance tunnels and open channels that direct water into two turbines located in an underground powerhouse, originally constructed in the 1970s. At the time of construction, the tunnel was partially supported with shotcrete or rock bolts, with no further ground support added since construction. Two sonar surveys in 019 and 01 identied two adacent large FoGs in the tunnel, approimately 1.2 km from the tunnel outlet. Historical geological and geotechnical information indicated that the FoGs occurred within a 60 m wide fault zone. Remediation plans were developed, which included stabilization of the outlet channel, the portal, the tunnel leading up to the FoG areas (1.2 km length) and the FoG areas. Several remediation options were considered to restore the tunnel, including construction of a diversion tunnel to bypass the FoGs or remediation of the FoG areas with steel ribs and backlling the void above the FoGs to surface.

Jun 23, 2024

By C. A. Heiland

THIS year's review of geophysical activities has a somewhat different complexion than usual. With the ending of the war, the time seems opportune to supplement the customary report on operations and discoveries in oil and mine exploration by a review out-lining the contributions of geophysicists to the. war effort. To give as much space as possible to the latter, presented as Part 2, some of the usual review features have been omitted from the statistical section, given as Part 1 immediately following.

Jan 1, 1946

"Syncrude Canada Ltd. operates one of the largest surface mines in the world. The mining operation has two distinct phases: (1) the removal of the overburden, utilizing trucks and shovels; and (2) the mining of oilsand with drag lines and bucketwheels. Both phases combined move approximately 330 000 BCM per day.In support of current production demands and to provide a contingent oi/sand source, Syncrude has developed an Auxiliary Production System (APS) supported by the truck and shovel operation. This system utilizes oilsand sources within the existing mine area on an as-needed basis.The recent increased capabilities of the processing plant to handle a larger volume of oilsand has increased the reliance of the APS system. To facilitate the increased capacity, an auxiliary mine was developed external to the Base Mine operation with a production capacity of4.7 MBCM of oilsand per year.Development of the Northwest Auxiliary Pit began in January 1990, with the first cubic metre of oilsand taken to the plant in June, 1990. The Auxiliary Pit, as designed, has a total ore reserve of 68 MBCM of oi/sand."

Jan 1, 1993

By Paul C. Merritt

Samuel Hopkins, an 18th century inventor from Philadelphia, has been little noted nor long remembered by History, but it was he who on July 31, 1790, obtained what no other man can ever achieve -the first patent issued by the Government of the United States. Signed by President George Washington, the patent guaranteed to Hopkins the protection of the American Government for his "improvement, not known or used before, . . . in the making of Potash . . . by a new Apparatus and Process." The patent itself is no longer important, but it serves as a milestone in the development of an industry that is now rapidly moving to fulfill its role as a mineral to feed the world. Potash ranks as one of the oldest products of Man, having been used as a condiment by the habitants of Gaul a thousand years before Athens achieved its Golden Age of culture. By Hopkins' time, the uses of potash had changed considerably, going primarily into glass-making, tanning, soap, and explosives, yet the same sources and techniques of manufacturing potash used during the earlier 2000 years-that is, leaching of plant ashes in iron pots with water, followed by water evaporation and crystallization of the potassium salts-were still being used.

Jan 10, 1966

By A. H. Rhoades

The modern polarizing microscope with such accessories as cameras, infrared devices, reflectance and/or transmission photometers, indention hardness, and heating stage is used to characterize coal, coke, and other carbon forms. It allows characterization of coke by-products, such as tars and pitches and their insoluble residues. A useful product of the microscopic approach is the coal petrographic analysis which permits the prediction of coke strength carbonization pressure and volume change. Carbonization tests are expensive, time-consuming and require large amounts of coal. Tests on the coke show it to be strong or weak but give no indication of why. Petrographic analysis requires grams of coal and yields data that indicates why the coal produces coke of a given quality. Small samples from drill cores are sufficient for petrographic analysis. These data are also used to optimize blends for coke production. When coke-plant problems occur, ~he microscope can be used to check the coal blend proportions, as well as for weathered coal. Microscopy is useful in spore correlation work which may be a prerequisite to sound coal reserve estimates. Dispersed vitrinoid reflectance studies are used to determine the degree of organic metamorphism which serves to establish oil and gas deadlines. Tars and pitches are examined microscopically for the amount of normal solids as well as the size of undesirable carry-over solids resulting from pollution abatement practices in coke works. The microscope is also used to study coals for gasification and liquefaction.

Jan 1, 1981

In 1987 the control strategies at the then ZC Mines' New Broken Hill Consolidated concentrator were a miscellaneous mixture of computer hardware and technology for ISA, grinding and residue thickener control. Field instrumentation was based on current-to-air technology of approximately the 1960s. Decisions were made to rationalise computer and field instrumentation technologies; the object being to consolidate control loops into one system to enable expansion of the system to include all facets of plant operation. The first stage was to install a DEC Micro PDP 11/23 computer and serial line communication as recommended by AMDEL Ltd, for the ISA system, as discussed by Walsh and Freeman (1988). The second stage was to select and install a distributed control system for the centralisation of the control loops into one system, and to replace field instrumentation with state-of-the-art technology. This paper deals with the second stage of the rationalisation, in an attempt to give an insight into what is required when personnel are faced with such a decision, details of costs involved in keeping a system functioning and utilised; and the requirement to train personnel for acceptance of further control strategies.

Jan 1, 1991

By Bruce Cavender

Historically, the processing function has been regarded as efficiently managed as long as production costs were kept low, recovery was adequate and sufficient plant capacity was avail-able. In this paradigm, processing is viewed as capable of making only a limited contribution to a company?s competitive advantage. However, the processing function can provide a primary vehicle for building critical competitive capabilities. Processing organizations should be encouraged to become so accomplished they generate new opportunities for other functional groups and thereby influence a company?s overall strategy. This requires a deep shift in processing?s role, in its self-image and in the expectations of it held by managers in other functions. Specific plant improvement techniques ? total productive maintenance (TPM), loss control, etc. ? should be viewed primarily as means for building strategically valuable processing capabilities. Different improvement strategies create different kinds of capabilities and present new strategic options. Broadly speaking, a mineral-producing company seeks competitive advantage through two principal activities: the development of new mineral production and reserves and the optimization of existing operations. These lead to increases in ore reserves, production levels and cash flows that are manifested in increased profitability and, hopefully, increases in the price of the firm?s stock. The profitability of a minerals company is a function of the overall profitability of the industry sector in which the company participates and the firm?s competitive position within that sector relative to those of its competitors. Competitive advantage within the industry comes from two sources: the ability to maintain lower prices than competitors for the same product (cost leadership), or from the sale of products with unique properties that justify higher prices (product differentiation; Porter, 1980). Most mineral companies produce fungible commodities that are sold to anonymous customers, and sustainable cost advantage is the only long-run strategy available to these companies to enhance profitability.

Jan 1, 2008

To provide cooler air to miners working in hot areas of mines, particularly new deep hardrock mines. Approach Air supplied to hot working areas of mines is cooled by passing it through a series of water sprays. How It Works Water nozzles mounted inside a section of ventilation tubing release cooling sprays of water into the air being blown through the tube. The prototype of the water spray cooler consists of six evenly spaced water sprays located inside a 10-ft. long section of 16-inch-diameter fiberglass ventilation tubing. See diagram. This section of rigid tubing is installed into one of the positive pressure ventilation tubing lines that conduct fresh air into working stopes. The intake manifold to the six water sprays is connected to the mine?s cool water line, and the water valve on the manifold is opened. Warm ventilation air being supplied to the stope passes through the water sprays, and is cooled by the lower temperature water.

Jan 1, 1979

By Stefan Wallner, Andreas Filzwieser, Stefan Konetschnik, Reinhard Preiss, Iris Filzwieser

"Process Safety Management for METTOP means avoiding risks as far as possible - but also dealing with the residual risk by using all existing management tools or external assistance, if required. The presented paper has two parts. The first one introduces a new and very safe cooling technology for metallurgical furnaces. The second part shows how to deal with the residual risk as well as minimize it by using the tapping area of an electric arc furnace as an example.Today more and more intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetime, making cooling technology an important aspect of furnace operation. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion.To overcome the disadvantages of water, a new cooling technology using an alternative cooling medium, namely ISIS B (a special kind of ionic liquid) was developed. The main advantage of ISIS B is the fact that no explosion occurs when this liquid comes in contact with molten metal. The working temperature range of ISIS B of 50 to 200 °C results in other advantages as there are no corrosion problems and no risks of hydration.The fact that no explosion occurs when ISIS B contacts molten metal leads to a revolutionary solution for the metallurgical industry in terms of safety. Especially in critical areas - like tap-holes - new safety standards can be achieved.Together with the TÜV Austrian Holding AG a risk analysis was done for a water cooled tap-hole as well as for a tap-hole cooled with ionic liquids. It is shown that using the new technology the risk can be decreased dramatically and the importance of a best available technology is described."

Jan 1, 2014

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V, 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicated that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

May 4, 2023

By H. F. Weaver

The 19th National First-Aid and Mine Rescue Contest was held in the Civic Center, Charleston, w. Va., on October 2, 3, and 4, 1961. The meet was sponsored by the Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with State mine inspection agencies, management and labor of the mineral extractive industries, and other groups interested in safety. The Arrangements Committee, as authorized by the General Committee, made the necessary arrangements for conducting the 1961 contest. Members of the Arrangements Committee were: George Trevorrow (chairman), Bituminous Coal Operators' Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; Harry Gandy, Jr., National Coal Association; and James Westfield, Bureau of Mines.

Jan 1, 1962

By C. C. Furnas

Despite the fact that a great many industrial processes depend on efficient contact between a gas stream and a bed of broken solids for their operation, the data in the literature are very meager. Several investigations3 have been undertaken, but the work has been limited in scope and application. BUREAU OF MINES PROGRAM OF RESEARCH For the past 10 years the United States Bureau of Mines has been engaged in research with the object of formulating a more or less complete quantitative theory of the workings of the iron blast furnace. Obviously, in order to do this one of the essentials is to have considerable definite information on the laws of gas flow through beds of broken solids. This report in a brief summary of the experimental work on the problem which has been done at the North Central Experiment Station. The complete report with more detailed tabulation of the data and explanations of the experimental procedure is in process of publication in the form of a bulletin.

Jan 1, 1928

By James C. Cawley

The Bureau of Mines conducted an investigation to statistically determine the mean current or voltage for resistive, inductive, and capaci-tive circuits that would cause spark ignitions in 8.3% methane-air, 5.3% propane-air, and 7.8% ethylene-air mixtures. Each mean ignition current or voltage was determined on the basis of 100 trials. Each trial consisted of 400 revolutions, 200 in each polarity, at 80 rpm of the standard breakf1ash apparatus. In general, spark ignition curves published in UL 913 for resistive and inductive circuits represent approximately the mean current values determined in this study, while published capacitive circuit values in methane are considerably less than the mean voltage values from this study, especially for a capacitance of less than 100 ~F. For resistive and inductive circuits, spark ignitions were obtained at currents con-siderably below those in the published curves, but this study was not optimized to find minimum ignition values. This report defines "safety factor" as applied to intrinsic safety testing as the energy ratio of the mean values of ignition current or voltage for two test gases. The safety factors presented in this report are not constant with voltage or current and, therefore, are not recommended for use.

Jan 1, 1986

By Gary English

"Tunnel safety is evolving as science, engineering and technology make advances. Applicable safety codes and standards simply do not cover all the potentials of design, construction and operation. This paper reviews a series of tunnel projects code gaps in Seattle USA that were uncovered during the design and construction of a new highway tunnel, conversion of bus tunnels to combined road and rail tunnels, new rail tunnels using TBM and NATM, conversion of a road tunnel to light rail, and retrofit of an existing road tunnel to add lanes and improve safety systems. The perspectives of the ‘fire code official’ (Authority Having Jurisdiction) on methods to identify and resolve gaps in safety code and standard regulations, while garnering the consensus of the owner, designer, and contractors are presented. Additionally, the emergency responder command perspective on safe tunnel design, tunnel rescue during construction and operational safety is explained TUNNEL SAFETY EVOLUTION The underground has become nearly the only option to provide essential transportation corridors to continue our economic growth in key global areas. Tunnels are not built on a whim. Often significant portion of a regions wealth are invested to meet current, and hopefully future transportation demands. There are more transportation tunnels being built now than at any time in the planets history. The location of these tunnels is often selected for us based upon regional demand. Most commonly under densely populated urban centers and between populations’ centers to bypass geologic conditions like mountains and water bodies. Tunnels are being built in unforgiving soils, between tectonic plates, in extremes environmental conditions and often, under the very heart of the highest density population centers on the planet. All of these locations can bring with it conditions that challenge our common assumptions about safety. These extraordinary locations and soils create risks for both those constructing the tunnel, and in design engineering to meet the ‘minimum’ requirements at the lowest costs. There is lengthy history of above ground safety. Most countries and major local jurisdictions have adopted, or created safety requirements for the construction of above ground buildings. Through decades of use, these safety requirements have evolved, changed and been expanded to cover a wide gamut of actual and potential safety risks. However, the use of the underground for tunnel transportation corridors has grown exponentially with limited attention to safety requirements."

Jan 1, 2016

By A. Sobering, G. N. Carlson

"This paper describes the conversion of the grinding section of the W a bush Mines pelletizing plant from conventional wet, open-circuit trunnion overflow ball milling, with filtering, and bentonite mixing on a common conveyor belt, to dry, open-circuit, grate discharge grinding, with pug mill mixing of bentonite and water at individual mills.The test work and data on operating economies to justify the cost of conversion are given. It is too early, at the time of writing, to have complete operating confirmation, but data are available. A brief description of the original plant is included."

Jan 1, 1971

By T. A. Rickard

The dictionary defines 'jargon' as "barbarous or debased language". This description does not suffice. Quiller-Couch has said, it is "a kind of writing which, from a superficial likeness, commonly passes for prose in these days, and by lazy folk is commonly written for prose, yet actually is not prose at all ". The two main vices of jargon, he says, are "that it uses circumlocution rather than short straight speech", like the Babu who reported his mother's death by saying: "Regret to inform you, the hand that rocked the cradle has kicked the bucket ". Its other chief' vice is that "it habitually chooses vague woolly abstract nouns rather than concrete ones", like the newspaper statement; "He was conveyed to his place of residence in an intoxicated condition", instead of saying, "He was carried home drunk ". Jargon is "an infirmity of speech", it is not journalese, but akin to it. "Like respect- ability in Chicago, jargo4 stalks unchecked in our midst" and renders much technical writing ridiculous. It deals in periphrasis instead of going straight to the point, it loves the abstract rather than the concrete, it dabbles in words of sound rather than of meaning. Avoid it, despise it., if you purpose earnestly to write well. "III literature as in life he makes himself felt who not only calls 4 spade a spade but has the pluck to double spades and re-double." * Jargon is rampant in technical publications. Catalogues and other advertisements are conspicuous offenders, but with these the critic is not concerned, except in so far as such 'write-

Jan 1, 1931

By Patrik Fredriksson

Thermodynamic data concerning FeO-containing slags is of importance in ladle refining of steel. With a view to generate a set of reliable and self-consistent thermodynamic data for these slags, experimental determination of the activities of FeO in binary and ternary slags was carried out using the gas equilibration method involving CO-C02-Ar gas mixtures at steelmaking temperatures. The slag samples in Pt crucibles were quenched after the equilibration and subjected to chemical analysis. The thermodynamic activities of "FeO" in the slags were calculated from the experimental data. The results are incorporated into a thermodynamic description of silicate melts in the present laboratory. The model is based on a Temkin-Lumsden approach and is able to compute the thermodynamics of higher order systems from the lower order ones.

Jan 1, 2003

By M. Mustafa Kahraman, Sean Dessureault, W. Pratt Rogers

Most contemporary mines have considerable amounts of data. Structured and unstructured large data sets are colloquially named big data. Much of the data in mining operations come from a variety of systems, each with different databases and reporting environments. Standard technology deployments create a Bsilo-ification^ of data leading to poor system benefit. Through modern server monitoring and systematic approach, data utilization and value can quantifiably be measured. The Data Utilization and Value Index (DUVI) can quantify business intelligence best practices and user interaction. This study seeks to provide a data management tool to measure data utilization across the process of converting data into action.

By Xiao Hong, Zhang Wenqiang, Gao Bing

The characteristics of top charging coke (coke 1) and stamp charging coke (coke2) were investigated. The weight loss ratios of two kinds of cokes with and without alkalis were measured after reacting with CO under the temperature of 2 900, 1000, 1100 and 1200 °C respectively. The microstructures of original cokes were observed by SEM. The experiment results show that, with no addition of alkali, the weight loss ratios of coke 1 and coke 2 were nearly the same under the temperature of 900 and 1000 °C. While the weight loss ratio of coke 2 was much larger than coke 1 under the temperature of 1200 °C. With alkali-rich, the weight loss ratio of the two cokes was almost the same at 1100–1200 °C.

Mar 1, 2017