Search Documents

By M. D. Johnson

The San Andres mine, located in the western mountain region of Honduras, Central America, contains epithermal gold mineralization as disseminations, in quartz-chalcedonic veins and stockworks. Host rocks include a thick sequence of Cretaceous to Tertiary conglomerates, sandstones, rhyodacite tuffs and andesites. Mineralization is controlled by northwest and northeast striking, normal faults and fractures which dip steeply east and west. Currently, 500 STPD of 1. 93 Grams/MT gold ore is being open-pit mined from the conglomerate and andesite. The mine is at the west end of a mineralized zone that can be traced over an area of approximately 1.5 square kilometers.

Jan 1, 1993

By A. A. Shirzadi, E. R. Wallach

"Liquid gallium has been used successfully to modify/remove the surface oxides prior to diffusion bonding similar and dissimilar nickel-base superalloys. Using this approach, bonds in nickel-base superalloys with ""virtually invisible interfaces"" were produced, and the compositions in the bond region were very close to those of the bulk alloys. Room temperature tensile and bend tests showed no preferentially failure at the bond lines. Creep tests on samples made between two different Inconel alloys also showed failure away from the joint, i.e. in the parent metal of the Inconel alloy with lower creep resistance. The high temperature lifetimes of these samples were as long as those of the unbounded Inconel, confirming that the joining approach has no adverse effect on the nickel-base superalloys being joined."

Jan 1, 2006

By S. Kline

The compositions of metamorphic minerals of the south limb of the Dore Lake Complex have been determined by microprobe techniques. Mineral assemblages typical of the greenschist facies occur in Mg-rich bulk compositions, but in Fe-rich rocks albite-epidote amphiboli te facies assemblages occur. Low oxygen fugaci ties and a general paucity of metamorphic fluids prevailed in most of the complex, but a higher oxygen fugacity is indicated near the Chibougamau Pluton, and a local abundance of C0z and Cl in fluids near the pluton is suggested by the presence of scapoli te. The metamorphic gradient overprinted on the complex near the Grenville Front is apparent in mineral chemistries as well as by the appearance of garnet. Chlorite becomes richer in Mg, and iron is fractionated more strongly into hornblende. The amphibole also increases in Alz03.

Jan 1, 1984

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

By Timothy A. Clancy

To help reduce the Nation's dependence on imported chromite, the Bureau of Mines is conducting research on the use of dolomites as an alternate material. Dolomite is a plentiful domestic resource and offers certain advantages as a refractory raw material. A review of the literature has indicated that there are many sources of high-purity dolomite in this country and that European nations use a greater proportion of dolomite refractories, primarily in steelmaking, than the United States, The Bureau of Mines characterized 14 domestic dolomites as to chemistry, density, mineralogy, microstructure, and thermal behavior, to develop baseline data on their suitability as refractory raw materials.

Jan 1, 1983

By Jogeshwara Sahu, Sapan Kumar Kandi, SANDEEP KUMAR JENA, Sachida Nanda Sahu, Sarada Prasad Das

The present article reports the recovery of potassium from mica scrap using carbide lime waste and NaCl. The acid leaching of mica [4 M H2SO4 at 90 °C] can recover a maximum of 25% potassium. However, in the chlorination roasting (with CLW and NaCl) water leaching process, it was possible to recover potassium to the tune of 94% [900 °C, 50 min roasting; mica:CLW:NaCl 1:0.75:1]. The formation of water-soluble phase like sylvite (KCl) and water-insoluble phases like anorthite ( CaAl2Si2O8) and nepheline ( NaAlSiO4) confirms the complete breakdown of the mica crystal structure. The extraction mechanism proceeds with the formation of a transition state followed by the release of potassium as KCl. The characterisation studies using ICP-OES, XRD, FTIR and FESEM support the proposed extraction mechanism. The salt produced by the evaporation of roast-leached liquor confirms the presence of sylvite and halite only, which can be separated to get the fertiliser grade KCl.

Sep 29, 2021

By S Natsui, Y Goto, S Kawanishi, J Takahashi, H Nogami

The demand for copper increases yearly, and further improvements in copper smelting efficiency using flash furnaces are required. This study was conducted to understand and promote the interfacial reaction associated with the collision of silica flux and iron oxide particles, ie the formation reaction of fayalite slag, in the reaction shaft of the flash furnace. High-temperature microscopy was used to observe the reaction behaviour of a 2 mm granular SiO2 reagent in contact with micrometreorder- sized FeO reagents in situ. When the amount of FeO was lower than the stoichiometric amount with SiO2, the molten slag formed at the interface between FeO and SiO2 diffused into the SiO2 particle before dissolving the remaining FeO particles. It did not contribute to the subsequent reaction, and despite having the lowest amount of FeO among the samples in this study, many unreacted FeO particles remained on the surface of the samples after testing. On the other hand, under conditions with high FeO content and close to the eutectic composition of the FeO-SiO2 system, a liquid phase formed from low temperatures, gradually increasing in volume and eventually completely dissolving the 2 mm SiO2 grain. These results indicate that the early-stage slag is essential in increasing the interfacial area between FeO and SiO2 and facilitating the supply of FeO to SiO2. In other words, the FeO/SiO2 determines the amount of liquid phase and significantly influences the subsequent interfacial reaction rate between FeO and SiO2. Therefore, the local FeO/SiO2 of the particles falling down the reaction shaft should also be optimised to ensure early slag formation. Meanwhile, the time required for 2 mm SiO2 to complete the reaction for the temperature history employed in this study was significantly longer than the particle residence time in the reaction shaft. Further detailed investigation of the effects of silica flux particle size, composition, and reaction temperature on the reaction time will help find the conditions under which the reaction of silica flux can be completed in the reaction shaft. These kinetic approaches could contribute to future innovations in the copper smelting process using flash furnaces.

Jun 19, 2024

By T. L. Joseph

"IntroductionThe efficiency of ore reduction in the blast furnace and fuel requirements depend upon the degree of uniformity with which reducing gases can be distributed through the stock column and upon the permeability of individual pieces of ore and sinter. If the ore is fine, the major problem in reduction is to get the ascending gas stream to the surface of the ore-Hard, dense ores of low permeability, mined in coarse sizes, tend to improve the permeability of the bed, but unless they are crushed to the proper size they reach the hearth unreduced.Surveys by the Bureau of Mines have shown conclusively that the gas distribution in the upper three fourths of the furnace is far from ideal. Furnace lines, top design, and methods of charging are important, but more thorough size preparation of the ore is necessary to eliminate size segregation at the stock line, which inevitably leads to non-uniformities in gas distribution.Because of the quantity of sinter now produced close study of the characteristics which determine its behavior in smelting is warranted. As the use of concentrates increases agglomeration will become more of a necessity. Improvements in the physical character of the ore burden are particularly important to plants using coke of poor physical quality. In addition to aiding reduction, improved physical properties of the ore burden will permit the use of higher blast heats, which is equally important.Reduction Tests on Fine Sizes of SinterPrevious reduction tests on minus 0.742— plus 0.525--inch pieces of commercial sinters revealed large differences in porosity and reducibility. The results have been published in a former report. 3 Although the physical properties of the sinter, particularly porosity, were found to be of major importance in determining the rate of deoxidization, it appeared that certain chemical properties of the sinter appreciably retarded the reduction of sinters high in silica. This was attributed to the presence of fayalite, which has been identified by Schwartz and by Luyken and Kraeber4 as an important constituent of sinter. Although furnace operators and metallurgists have assumed that iron silicate is more difficult to reduce than hematite or magnetite, definite data on the reduction characteristics of this material were not available. Tests were undertaken, therefore, to develop a method for de-termining the amount of iron silicate present in sinters so that its effect upon reduction could be observed."

Jun 1, 1934

By Y. J. Wang

This paper deals with the application of linear programming to the solution of mine ventilation network problems which involve only the controlled splitting of air. An airway whose air quantity is to be controlled to a prescribed value is called a "fixed-quantity" airway. In a network where the fixed-quantity airways are increased in number and are distributed such that the air quantities for the remaining airways are uniquely determined by Kirchhoff's first law, the problem reduces to determining the head losses and locations for air regulators and fans. This is one of the network problems encountered most often in underground coal mines. By formulating Kirchhoff's second law as a set of linear constraints and the total air horsepower supplied by fans as a linear objective function which is to be minimized, the problem is analyzed through the technique of linear programming. Some important properties of the problem are discussed and examples are presented.

Jan 1, 1971

By Cassandra A. Wetzel

"Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.INTRODUCTIONRock-socketed mini-piles are a common and desirable deep foundation alternative to support loads more than 40 tons in New York City. Limited vertical clearance, accessibility, vibration control, and load capacity make this pile type attractive; it also does not require a static axial load test when socketed into rock. This added benefit makes this alternative all the more feasible.The installation of a drilled pipe extending to bedrock through a glacial till deposit presented challenges to the contractor and engineers to confirm the casing is seated sufficiently into the rock prior to drilling the rock socket. The loss of soil between the steel pipe and the till/bedrock interface can compromise the performance of the pile and soil loss can result in settlement of the ground surface.This paper presents the design and construction method changes made on one project during the installation of ten limited access rock socketed mini-piles."

Jan 1, 2017

By Cameron Soltys, Hamid Ghorbani, Maher Al-Dojayli

Cooling staves in blast furnaces are used to minimize the process heat loads on steel shell and refractory system. Copper staves are exposed to significant fluctuating thermal loads which may lead to premature stave failures due to cracks, water leakage, bending, abrasion and resultant wear. In this paper, an assessment methodology is presented to evaluate the effect of thermal cycling on copper staves including bending, fatigue and thermal ratcheting. This approach incorporates temperature-dependent copper properties including creep and plasticity to more accurately capture inelastic deformations, damage and fatigue in staves under transient and cyclic thermal loading conditions. Root cause failure assessment and improvements to copper stave design can be assessed using the presented methodology.

Oct 1, 2019

By R. F. Abernethy

A modified Unterzaucher method was applied to the direct determination of oxygen in coal. Coal samples were pyrolyzed in a nitrogen atmosphere, and the gaseous oxygen compounds liberated were converted to carbon monoxide by a platinized-carbon catalyst at 9000 C. After passing over heated copper and through a tube containing soda-asbestos and magnesium perchlorate, the purified carbon monoxide was oxidized to carbon dioxide by iodine pentoxide--liberating an equivalent amount of iodine. The iodine was titrated with 0.02 ~ sodium thiosulfate; in a few tests the weight of carbon dioxide produced was determined. Direct oxygen determinations of coal included organic oxygen from the coal substance, plus a small quantity of inorganic oxygen derived principally from carbonate minerals and from combined water of silicates in the mineral matter. The influence of mineral matter on the direct oxygen determination was investigated by testing (1) untreated coal, (2) demineralized coal from which most of the mineral matter except pyrite was removed by treatment with hydrofluoric and hydrochloric acids, and (3) coal samples treated with dilute hydrochloric acid.

Jan 1, 1966

By N Bezuidenhout

The performances of ten field-scale experimental final covers were evaluated over an eight-year period. The covers were evaluated as part of the rehabilitation of acid generating coarse coal reject dumps and opencast coalmines in the Northern KwaZulu Natal province in South Africa. The main purpose of the experimental covers was to restrict rainfall infiltration into acid generating coal discard. The mean average rainfall over the monitoring period was 839 mm with 84 per cent occurring between October and April. The average evaporation was 2100 mm. The site is described as a ædry siteÆ since the evaporation exceeds rainfall by a significant margin. Approximately 30 per cent of rainfall infiltrated the uncovered cells. Rainfall infiltration into the fine coal discard was reduced to 20 per cent and 15 per cent for a 300 mm and 500 mm cover respectively. Infiltration was reduced to ten and 12 per cent of rainfall for fine coal discard provided with a 1000 mm double soil cover and a compacted bottom layer. This relatively high infiltration was probably caused by moisture being entrapped in the bottom retentive layer, and not being released by evapotranspiration. The best performing cover comprised 1000 mm single soil with a compacted bottom layer and infiltration was reduced to four per cent of rainfall. Rainfall infiltration into sloped cells varied between seven per cent and 14 per cent of rainfall. The computer software, SoilCover, was used to predict infiltration and moisture content in the cover. Predictions of rainfall infiltration were accurate, but were less accurate for covers where the hydraulic properties of field compacted soils were not adequately characterised. Oxygen ingress was significantly reduced for cells provided with a 1000 mm cover. Oxygen concentrations were generally below one per cent, with the exception during exceptionally dry periods when the cover dried out, resulting in increased oxygen ingress. For other covers, and the uncovered cells, oxygen concentrations were close to atmospheric concentrations. During the eight-year monitoring period, acid breakthrough occurred in five of the cells, including three uncovered cells, one cell with a 300 mm cover and one sloped cell. In contrast, cells covered with 1000 mm, bottom compacted soils shows a marked improvement of leachate quality, indicating that sulfide oxidation processes have been slowed. There was a distinct relationship between oxygen ingress and leachate quality for all of the cells. No cover degradation was evident over the eight-year period, except for some erosion observed on a sloped cell. The results indicate that the onset of acid drainage can be delayed by perhaps hundreds of years and salinity loads can be reduced by more than 90 per cent, if coarse coal reject dumps in the KwaZulu-Natal provinces in South Africa are provided by an adequate cover system. These research outcomes can be extrapolated and applied to other dry site regions where similar materials are being considered.

Jan 1, 2003

A hidden asset in most exploration and mining activities is data. Common practice involves the spending of large amounts of money to discover, define and prove the viability of a mining project. Some organisations have used operations research analysis and internal costing methods to allocate a value to their data and to compare the costs of data maintenance to other more tangible activities like plant and equipment maintenance. Those organisations, which do not undertake such an analysis often, have little knowledge or understanding of the extent and the worth of their data. Often the organisations lack of knowledge and understanding of the data is indicated by their failure to fully exploit or realise their opportunities. The focus of this paper is to discuss new technologies that optimise the management and security of collected and derived data. The technologies discussed are components of the software systems acQuire and MineSight.

Jan 1, 1999

By Son Hoang Nguyen, Thanh‑Hai Pham, Duoc Van Tran, Dung Thi Kim Nhu

Apatite ore plays a critical and irreplaceable role in fertilizer production and is being upgraded in quality in northern Vietnam. The old tailing of the Bac Nhac Son beneficiation plant (Vietnam) has a significant apatite amount in the form of coarse unliberated particles. These millions of tons of tailing ore have 6–8% of P2O5 content, which can be retreated to provide fertilizer factories. This work presents the results obtained in recovering apatite from this tailing in the laboratory. By the combination of the processes of classification, preliminary flotation, re-grinding and cleaning in the flotation column, an apatite concentrate of 30.68% P2O5 can be obtained with the total recovery of 37.76% from the initial tailing of 7.56% P2O5. The study results not only provide an appropriate technical solution for recovering the apatite ore from tailing ore but also have outstanding meaningness in the recovery of mineral resources under the context of a circular economy.

May 24, 2023

By Julian Glasser

Starting with rutile, containing more than 55% TiO2 and of the proper particle size, the commercial production of titanium tetrachloride via fluidized bed chlorination is relatively very simple and economical. As compared to shaft chlorination, it operates at a much higher capacity for given sizing of equipment, and appears more foolproof, requiring less attention. Operating data were obtained on a 53" diameter fluidized bed chlorinator using Australian rutile and petroleum coke of controlled particle size. Production rates varied from 20 to 50 tons of crude TIC14 per day for a campaign extending over one month. Close to theoretical yields and efficiencies were obtained from the viewpoint of chlorine and/or rutile consumption. Details of important equipment design, critical operating conditions and pertinent results are described.

Jan 1, 1962

By W. A. Smith, M. C. Bekker, C. Marnewick

Projects or project-orientated approaches have become a common form of work in nearly all sectors of economies. This has led to concepts such as ‘projectified’ and ‘project orientated’ organizations. By defining projectification of a company, industry, or economy as the share of project work in total work, one can reasonably determine the impact that project management, and by default projectification, has had on that company, industry, or economy in terms of staff optimization and allocation. This paper presents the results for such a projectification study of the South African mining industry. This sector has long been a significant contributor to the country’s economy from a gross value added (GVA) and employment point of view. Understanding the impact of projectification and the project management way of work on this industry may potentially add significant value to both the mining and project management knowledge areas. We show that although the mining industry is considered by some to operate in archaic ways, the level of projectification has increased over time, and now represents approximately one third of all work conducted.

May 1, 2021

By Michael Sokaski

A dense-medium cyclone pilot plant was built to clean 112-inch to 0 size coal. This pilot plant does not require the removal of the extremely fine material (usually minus 1/2-mm) from the feed, which is necessary in conventional dense-medium cyclone plants. The essential difference between conventional cyclone plants and the pilot plant is in the medium-recovery system. The latter uses a combination of sieve bend screens, classifying cones, and magnetic separators for medium recovery. Eight tests were run in the pilot plant at a feed rate of 5 tons per hour with four different raw coals and one crushed jig middling product. Sharp separations were obtained as indicated by an average error area of 27 and probable error of 0.047 for the 112-inch to 200-mesh size range. Magnetite loss averaged about 2.5 pounds per ton of feed. The influence of several factors on cleaning performance of the cyclone was investigated. The diameters of both the overflow and underflow orifices were found to be important for optimum cleaning performance, but these diameters could vary over a wide range without serious effect; however, if this range was exceeded, cleaning performance deteriorated. Better cleaning performance was obtained when the cyclone inlet pressure was increased from 9 psig to 13 psig. The size of the magnetite particles in the medium was found to have a substantial effect, and the best cleaning results were obtained with grade B magnetite. Demagnetizing the magnetite in an effort to decrease the effective particle size did not improve cyclone performance.

Jan 1, 1963

By B. K. Cantrell

The use of diesel equipment in underground coal mines is controversial because "whole diesel exhaust" is regarded as "a potential occupational carcinogen" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2' and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.

Jan 1, 1991

By K. Thirumalai

The feasibility of breaking hard rock by thermal weakening and subsequent mechanical impacting was tested, Field tests at a basalt quarry in Dresser, Wis., demonstrated that large hard-rock blocks (5 by 5 by 5 ft) could be effectively reduced in size by this method. A series of secondary breakage tests, using air-propane heating, resulted in an average heating cost of $0.36 per ton. This combination energy approach provides an alternate means of size reduction of large hard-rock boulders for quarry and for underground are chute and grizzly operations where mechanical methods, used alone, are ineffective.

Jan 1, 1975