Search Documents

By P. C. Thakur

The productivity in coal mines, measured in terns of the output per manshift depends largely on the efficiency and speed of men and materials transport between working faces and the surface. The mechanization of coal winning and material handling processes has led to a great rise in the mine productivity (1). Early applications of power in U. S. coal mines were mainly electrical. The excellent traction available with the DC motor and the ease of the distribution of the DC power have made trolley wire installations for haulage very popular. In shallow mines with very limited emissions of methane it did not constitute a major hazard but as mine depths increased and corresponding emissions of methane also increased fire and methane ignition hazards have become very serious. Conveyors have proved economic where intense mechanization of coal faces generates a large output of coal from a single face, but the fire and respirable dust hazard associated with them are no less serious. Recognizing these shortcomings, the Federal Coal Mine Health and Safety Act of 1969 laid down numerous provisions for the safe use of trolley-wire haulage and conveyors (2) which generally improve safety but in some cases complicate mining operations and have decreased productivity significantly since 1969. In course of time as coal mines become deeper and hence gassier and as the emphasis on safety increases it would be inconceivable to use trolley-wire haulage under ground as already witnessed in several other countries with deep coal mines. With rising capital investments and cost of the protection against fire and respirable dust, the use of conveyors may also have to be limited to special areas, e.g. main entries. Indeed, there are only two alternatives available, namely; (1) Degasify the coal seams prior to mining and use conventional electrical power, or (2) Develop alternate sources of power which would be safer and yet efficient and cheap.

Jan 1, 1975

By J Webb

"It is vitally important in projects where the cut-off grade is low that there is no contamination during the sampling and sample preparation process, both in the ore and the waste zones. Failure to identify contamination could have devastating financial consequences for a project. The use of a variety of blank types is essential for ensuring that contamination is identified and eliminated at every stage of the sampling and sample preparation process. This paper examines an instance where an effective assay quality assurance and quality control (QA/QC) program was able to identify and eliminate a source of significant multi-element contamination in the prefeasibility stages of an open pit project. This examination includes the: evidence for contamination findings of the investigation process of resolving the problem and correcting the data evidence for both addition of metal and dilution through contamination potential impact on the project had this issue not been dealt with. It was through the use of a combination of blank types that the QA/QC process at Mount Isa Mines (MIM) identified a contamination issue at the first crushing phase of sample preparation. Identification of the contamination allowed MIM to stop assaying activities and work with the laboratory to correct the problem. The sampling program could then be continued with no further doubts about the sample preparation process. Contaminated samples were resampled from retained core. With the continuous monitoring provided by the blanks program, it was possible to ensure that only clean results went into the resource modelling data set. CITATION:Webb, J, 2014. When nothing is what you need – the importance of using blanks at all stages of sample preparation, in Proceedings Sampling 2014 , pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By J. L. Christie, R. H. Leach

SO much has been written recently about the use of silver to replace scarce metals that certain facts about silver and its uses should be of interest. Figures for the production and use of silver, taken from the Handy & Harman annual reviews of the silver market, are given in Table 1. It will be seen that the rate of production has remained fairly constant and has been affected in recent years by the production of base metals, of which silver is a by-product. In each of the years 1937, 1938, and 1939, the U.S. Government acquisitions alone exceeded the entire world production, the difference, of course, being made up by imports of previously accumulated stocks. In 1940 and 1941 the U. S. Government acquisitions plus the United States and Canadian uses in the arts and industries exceeded the Western Hemisphere production. The U.S. Government pays a premium price for silver newly mined in the United States, at present 71.11c. compared with the price of 35'/8c. for foreign silver, with the result that the current U. S. production is not used commercially for the arts and industries. At the time this is written (June 1942) there is much uncertainty as to the future effect of this situation.

Jan 1, 1942

By Xuyang Liu, Xuewei Lv, Yu Zhang, Xiaolong Wu, Chunxin Li

Titanium nitride is a broad-spectrum specific functional material because of its many superior properties. Therefore, it is necessary to investigate synthesis methods of TiN and alloys containing TiN reinforcement. In the current study, with the increase of nitrogen gas pressure and the optimization of routine ball milling parameters, the conventional mechanical ball-milling method can be improved, the nanometers TiH2-TiN composite powder can be synthesized successfully in a shorter time. Nitrogen gas filled in ball mill jar in which the pressure was 0.6 MPa. TiH2 powder was milled under nitrogen atmosphere at a spinning rate of 250 rpm. The results show that the stable TiN is formed after grinding for 2.5 h according to the X-ray diffraction pattern. DSC (differential scanning calorimetry) curves also indicate that milled compound powder adsorbs certain nitrogen gas. The gas adsorbed in TiH2-TiN composite can exist stably below 200 °C.

Mar 1, 2017

By S. A. Jeric

In-pit crushing and conveying of waste has been utilized in the mining industry for over 30 years. In recent years, innovations in crushing, conveying, and particularly waste and leach stacking technology have sparked a renewed interest in continuous haulage systems for large-scale open pit applications. A review of the advantages/disadvantages and operating techniques of crushers, feeders, conveyors, and stacking systems currently available is made. The paper examines some operations that are currently using large scale continuous haulage systems. Finally, a case study is presented that evaluates the application of a continuous waste haulage system in a large open pit mine in the Western United States, The case study includes a economic comparison with the existing truck haulage system.

Jan 1, 1997

By B. Rai

Processing of dolomitic phosphate ores remains one of the most challenging problems in phosphate ore beneficiation. The beneficiation plant at Jhamarkotra in Rajasthan, India for example is currently using a conventional double stage flotation process which involves first a fatty acids flotation to produce a combined dolomite-apatite concentrate (bulk concentrate) from associated silicate gangue. Dolomite is then separated from this bulk concentrate by flotation with fatty acids collectors and depressing apatite with phosphoric acid and sulphuric acid. This process requires addition of large dosages of reagents (H3PO4 and H2SO4) to depress apatite and to maintain highly acidic pH during flotation. Furthermore several cleaning and scavenging stages are needed to obtain the product of desired quality. We have developed and employed a molecular modelling based methodology of designing selective reagents for apatite-dolomite separation. We have been able to take into ac-count the differences in the distribution of calcium cations on these two surfaces in our design and hence develop novel phosphonic acid based depressants for apatite-dolomite separation with con-ventional fatty acids as flotation collectors. We have demonstrated the utility and power of molecular modelling based reagents design approach through this work on beneficiation of Jhamarkotra dolomitic phosphate ore using our novel phosphonic acids based depressants at pH?s close to natural pH. It was possible to reduce the MgO content of the ore from as high as 13.3 % to 1.5% in a single stage flotation. Our flotation separation results on Jhamarkotra ore with these new phosphonic acids based tailor-made depressants for apatite-dolomite flotation separation are discussed in this paper along with results of corresponding molecular modelling computations on the same system.

Jan 1, 2014

By Martin D. Larisch, Ronald Damen

The design and construction of temporary working platforms for cranes and piling rigs is a high-risk activity. It requires the careful selection of the appropriate input parameters to obtain the correct load cases, as well as the application of robust and reliable design methods to assess the required thickness and stiffness of the working platform. The document introduces some of the most common and most relevant guidelines for working platform design which are currently used in Australia and New Zealand. The authors will also discuss the basic assumptions and considerations about load transfer from construction plant, debate ground risk, compare the applicability of different design methods for various ground conditions and suggest some common verification methods for working platform certification.

May 1, 2022

By S. D. A. Hannot, H. Knapp

"High pressure grinding rolls (HPGR’s) are an energy efficient solution for comminution of industrial minerals and metal ores. The technology is successfully applied in an expanding field of applications throughout the minerals industry. HPGR’s compress and grind the particle bed in the operating gap between two counter-rotating rolls. The equipment provides a high capacity, low energy alternative for applications with conventional tertiary and quaternary crushing and grinding, with size reduction reaching from 100mm down to 25 microns product. In this process, maintaining a controlled and evenly distributed operating pressure between the rolls is very important. Due to feed segregation, the pressure distribution along the roll’s length can become uneven, resulting in a coarser product. This paper will show that the best approach to compensate and adapt for the uneven pressure is to allow the rolls to skew relative to each other. Coarser products are also caused by an inadequate pressure distribution: the much-discussed edge effect. To minimise the consequence of the edge effect, an optimised ratio for the roll length to diameter will be calculated. Furthermore, the design philosophy behind a cheek plate will be detailed. This cheek plate is used to retain the material between the rolls, reducing the edge effect while still allowing roll skew. Together these design considerations help optimise HPGR’s performance.INTRODUCTION Initially developed for the cement industry during the energy crisis in the 1980’s , high pressure grinding has been an accepted technology for many years. It has been successfully implemented throughout the minerals industry, with applications in base and precious metals, as well as industrial minerals processing. The comminution process relies mainly on size reduction through to compression and inter-particle crushing in a particle bed in the operating gap between two counter-rotating rolls. The equipment typically has a high unit capacity and low energy consumption, and is increasingly used as an alternative to conventional tertiary and quaternary crushing and grinding, in particle size ranges reaching from 100mm down to 25 microns. It can be applied to moist ores and dry material, in open circuit arrangement or in a closed circuit with dry or wet classification (screening, air classification)."

Jan 1, 2019

By C. B. Catanach

The development and in place leaching of a chalcocite ore body at Mountain City, Nevada is described. Block caving was used to induce permeability while ore removed during development was leached in heaps on the surface. Copper was recovered by precipitation on iron. Excess ground water which seeped into the mine was pumped into a deep disposal well. A parallel system was used to purify water by lime neutralization. Copper extraction was at an annualized rate of 11% during the first six full months of underground leaching and totalled approximately 30% during six months of heap leaching. Leach solution flow and distribution had a major effect on extraction rate. Enrichment of leach solutions with ferric sulfate did not produce conclusive results until analyzed with the aid of a leaching model.

Jan 1, 1976

By Alistair James, Mo Shahsavari, Leon Botham

The 1889 Johnstown Flood, which killed 2,209 people, was a preventable disaster stemming from systemic decisionmaking failures. This paper applies modern Risk-Informed Decision Making (RIDM) frameworks to analyze the historical context and explore alternative outcomes through hypothetical multiverse scenarios. By reconstructing the risk landscape of the South Fork Dam, we demonstrate how structured hazard identification, risk assessment, and stakeholder communication could have mitigated or prevented the catastrophe. Three counterfactual scenarios—proactive maintenance, community engagement, and regulatory oversight—are evaluated to quantify potential lives saved and economic benefits. The study acknowledges historical barriers, including technological limitations, lack of governance, and socioeconomic disparities, which constrained risk-aware decisions in the 19th century. The analysis draws critical parallels to contemporary engineering challenges, particularly in tailings storage facility (TSF) management, where similar risk blind spots persist. The paper concludes that RIDM is not merely a technical tool but a governance imperative, essential for ethical and sustainable engineering practice. By learning from historical near-misses and failures, the modern engineering community can strengthen resilience and accountability. This work contributes to the growing body of retrospective risk analysis, offering a methodological framework for applying RIDM to historical disasters to inform future safety standards.

Feb 22, 2026

By E. Ray Webb

A interest to geologists and to mining and petroleum engineers is a laboratory method for determining the dip and strike of sub- surface structures, as well as the direction of fault planes traversing them. The information is derived by making use of the magnetic properties of borehole cores which must show visible representations of bedding or fault planes. Complete knowledge of these factors aids greatly in the successful exploitation of both ore and petroleum deposits.

Jan 1, 1940

By Mark Osborne, Ray D. Peterson, C. Edward Eckert

"The theoretical melting energy requirement for a typical hypoeutectic aluminum-silicon alloy is approximately 520 BTU/lb. It has been demonstrated, however, that even a state of the art secondary processing-automated lost foam casting operation can exceed this value by at least an order of magnitude when the actual thermal energy input from melting to solidification is monitored. Metal transfer and holding operations constitutes over 65% of this expenditure. The authors present relative benchmark energy expenditure information by unit operation for an offsite melting/lost foam casting line with a daily throughput in excess of 100,000 lbs. Efficiency improvements through optimization of the current process, and anticipated energy values at the culmination of a U.S. Department of Energy sponsored project to develop, integrate and demonstrate an advanced melting, transportation, and dispensation system will be cited.IntroductionThe size of the U.S. aluminum remelt pool was approximated to be 14.21 billion kg (31.27 billion pounds) by a recent study?, with the engineered castings (foundry) sector accounting for 3.25 billion kg (7.16 billion pounds) or 23% of that total. This study considered overall process yield and all major contributors to scrap. The values cited, therefore, are more meaningful than simply tabulating annual pounds shipped by sector.The foundry sector consists of Sand Castings, PM Castings and Die Castings categories appearing in Figure 1. All other categories comprise the wrought alloy sector. Wrought alloy production enjoys an energetic benefit from both scale and a relatively continuous operation. Many foundry operations, however, operate in batch mode at less than design metal throughput with characteristically longer melt holding periods. Since any detention of molten metal beyond melting represents an overhead use of energy, melt holding (secondary) energy expenditures can appreciably inflate melting energy requirements in the foundry."

Jan 1, 2009

By Malte J. M Gurgel

Subsurface spatial planning is becoming increasingly important in view of competing underground applications. This development is influenced by global agreements to reduce greenhouse gas emissions. Therefore, precise knowledge of the underground space is a basic prerequisite for future applications. The three-dimensional registration and reliable georeferencing of underground infrastructures can establish a holistic geodata basis for such tasks. Those tasks are discussed both for the development of energy projects such as deep geothermal energy as well as for storage applications. Research on geothermal energy has been carried out at RWTH Aachen University as part of the SuperC project in a license field in the Aachen area since 2001. Recently, this research has been extended to include monitoring aspects in the overlapping GEObservatorium Aachen field. The documentation and visualization of underground activities using photogrammetric methods like Structure from Motion is discussed based on recent research in sites for the final disposal of radioactive waste. Finally, both applications provide an outlook on supporting underground projects by using high-resolution geodata.

Feb 1, 2025

By D. Ibarra, J. Jacob, A. G. Guezennec, P. d’Hugues, A. Archane

The lack of adequate gas mass transfer is a rate limiting step in many bacterial leaching processes. Oxygen often becomes a limiting factor because of its low solubility compared to the high demand induced by sulfide oxidation. One way of increasing the solubility of oxygen in water or in media solution is by increasing the driving force, i.e. raising the oxygen partial pressure in the gas stream supplied to the leach pulp. The use of oxygen is a well-known practice in high-temperature bioleaching reactors (above 70°C) whereas air is usually preferred in medium and low-temperature operations in order to avoid too high dissolved oxygen concentrations which could impact negatively the bacterial activity. The purpose of this study was to investigate the use of oxygen-enriched gas in bioleaching reactors at 40°C in order to improve the gas transfer in the system when operating at high solid load (20% and more). Bioleaching experiments were performed on a sulfide-rich tailing waste (pyrite 60%, copper 0.8%, cobalt 0.06 %, gold 1 g/t) using the “BRGM-KCC” bacterial consortia. The reactor used for the tests was designed on the basis of a new bioleaching reactor concept developed by Air Liquide, Milton Roy Mixing and the BRGM which uses floating agitators to inject gases and to mix and to suspend solids in the bioleaching solution. Two types of tests were carried out: with air injection and with oxygen enriched gas mix injection. The aim of this work was to confirm the capacity of bacteria to grow and to dissolve pyrite in this type of bioreactors in oxygenrich atmosphere, and to compare sulfides dissolution rates during both types of bioleaching tests. The results obtained show that the use of oxygen enriched gas mix does not decrease bioleaching performances compared to air injection. High metal extraction yields were achieved (above 80%). No deleterious effect due to oxygen use was observed on the bacteria despite the high level of dissolved oxygen reached in oxygen tests (up to 14 mg.L-1).

Jan 1, 2016

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermo-physical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at the University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous case is modeled with walls, each having a different set of thermo-physical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

By F. E. Patton

"IntroductionAT NORANDA, the strength of the ore and wall-rocks per-mitted mining in large open stopes. While some of the orebodies were small and could be mined out in one stope, in most cases their size was such that it was essential that ore pillars be left during the first stage of mining. In these cases, backfilling has been necessary for ground control and to facilitate the later recovery of the ore in these pillars.This paper discusses the development of the •backfill and •its use in pillar recovery.GeologyThe ore bodies at Noranda occur as replacement deposits in a block of rhyolite flows and breccias, bounded on the north by the Horne Creek fault and on the south by the Noranda Andesite fault. Mineralization consists of pyrite, pyrrhotite, magnetite, chalcopyrite, sphalerite, gold, and various tellurides.The main orebody is a massive sulphide deposit designated the 'H' orebody. It is elliptical in plan, measuring roughly 400 feet by 800 feet, and is divided into two zones -Upper H, extending from surface to the 1,500-foot level, and Lower H, from the 1 ,500-foot level to just below the 3,000-foot level.Mining MethodsOpen stope mining in both Upper H and Lower H zones has been fully described in previous publications (1). A brief review only of the mining methods will be given here."

Jan 1, 1952

By M. N. Pons, E. Benizri, B. Laubie, A. Bani, Université de Lorraine LRGP, P. Kidd, A. J. M. Baker

"Serpentine (i.e. ultramafic) outcrops in Europe cover more than 10,000 km2 and have a low-fertility and low-productivity, making them unattractive for traditional agriculture. In general, these areas are slowly abandoned by local farmers, affected by strong rural exodus and landscapes undergo a process of closure. However, ultramafic landscapes have the potential to provide multiple ecosystem services that can contribute to Europe’s goals towards insuring food security, production of renewable raw materials and renewable energy. Phytomining (agromining) aims at cultivating metal hyperaccumulator plants that are able to accumulate Ni and other strategic elements from metal-rich soils and transport them to the shoots (>1%), which can then be harvested as a bio-ore. Such metal-rich biomass can be used to recover highly valuable metals, e.g. nickel (Ni) and also to produce energy (heat, electricity). Nickel agromining can thus offer an eco-efficient alternative to classical pyro- or hydrometallurgical processes without disturbing the soil cover and the geology from soils and rocks that would be considered as low grade ores or sterile material for conventional mining methods.Phytomining agroecosystems can lead to better soil resource efficiency and can offer a fully integrated, new agromining agriculture that could cover thousands of km2 in Europe, benefit local communities with a sustainable rural development and provide a wide array of ecosystem services which will need to be optimised under a life cycle assessment methodology:1. Production of bio-sourced metal products2. Production of energy biomass3. Restoration of soil fertility for conventional agriculture (Ni stress)4. Limiting Ni intake by local populations and farmers5. Use and conservation of local biodiversity (plant and soil fauna and microflora) as cultivated ecosystems6. Store carbon in cultivated soils7. Enhance pollination activity at landscape level.Nickel agromining could therefore change the economical balance in historically-disadvantaged ultramaficregions of Europe"

Jan 1, 2016

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001

By Hylton R. Brown

Advertisements and articles in technical and trade journals announce the approach of a new age, in which plastics, light metals, laminated wood, and numerous other products or byproducts will be used in the construction of automobiles, airplanes, and furniture and equipment used in our factories, offices, and homes. Undoubtedly, after the war there will be many such developments which will introduce new manufacturing methods and new hazards to challenge the safety engineer. Already we know, from experience in laboratories and pilot plants where these new products are being tested, that there will be many fire and explosion hazards to be overcome. The danger of dust explosions may be one of the principal hazards, because thetic resins and other materials used in the plastics industry, as well as metal powders, wood dust, and other finely divided substances, are capable of forming explosive mixtures in air. Heavy losses of life and property have been caused by dust explosions in flour and feed mills, starch factories, and grain elevators, and it will be well to consider the possibilities that such losses may occur in any new industry and to provide all possible safeguards against hazards. Fortunately, we have learned something about the behavior of dust explosions and know something about the ease of ignition, limits of Explosive concentration, end pressure developed. Our efforts should now be directed toward the application of this knowledge in the development of safe operating practices.

Jan 1, 1945

By Fred Hodges

This paper describing the concentrator practice of the Hurley Plant of the Nevada Consolidated Copper Co. at Hurley, N. Mex., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Hurley concentrator has a normal daily capacity of 13,500 tons of ore, and for the first four months of 1930 the heads of the concentrator averaged 1.32 per cent of copper and 3.14 per cent of iron. The recovery for this period was 83.98 per cent and the concentrates produced averaged 27.54 per cent of copper.

Jan 1, 1931