Search Documents

By S. H. Katz

"At the annual meeting of the International Association of Fire Engineers at Kansas City, Mo., in June, 1919, the Bureau of Mines offered to cooperate with municipal fire departments for the purpose of obtaining information regarding composition of the air in burning buildings. (Katz, S. H., Statement made at Convention of International Assoc. of Fire Engineers: Fire and Water Eng., vol. 66, July 16, 1919, pp. 129-30, also Fireman's Herald, vol. 78, July 12, 1919, pp. 48.) The gas-mask laboratory of the Bureau's experiment station at Pittsburgh sent vacuum bottles for taking samples to fire chiefs in twenty-five cities, who had signified their intention to aid in this work. It was hoped to obtain one hundred or more samples, because statistics in quantity are necessary for drawing reliable conclusions concern-in the likelihoods of encountering irrespirable as in burning buildings. This far, eleven samples have been received by the laboratory. Results of analyses and pertinent data regarding these samples are given in the accompanyingEight of the eleven samples contained, no carbon monoxide; seven of the eight were taken above the ground level and one below ground. One sample taken above ground contained 0.03 per cent carbon monoxide, and this quantity is not dangerous to breathe for a limited time. Of the three samples taken below ground, one contained no carbon monoxide; the other two contained 0.10 and, 0.35 per cent, respectively. This indicates that in a burning building, the hazard from carbon monoxide is much greater below the ground level. The cause undoubtedly lies in the poorer ventilation that is usually found in cellars or basements. Abundance of ventilation provides the necessary air for complete combustion, or if incomplete combustion does occur, the carbon monoxide generated by the fire is greatly diluted with fresh air and swept away by the current. It may be noted that the highest proportion of carbon monoxide was found in a cellar where a fire as burning among piled cases. The difficult access of air to the burning parts facilitated the formation and lib ration of carbon monoxide. The smoke here was very light and no difficulty was experienced in breathing. Some of the air containing dense smoke showed little change from normal air by analysis. Thus the density of smoke or the irritation and difficulty it causes in breathing are no indication of the presence of poisonous gas. None of the samples shows important oxygen."

Nov 1, 1920

By H. Ankara

Determining the identicalness levels of the same model trucks working in open pit mine transportation system by means of statistical analysis methods is very significant in terms of availability analysis. In this study, the identicalness levels of two trucks picked randomly from the 170-short-tonne truck fleet working in open pit coal mine over one-year period were examined through a non-parametric test, Mann-Whitney U test for two samples. Time to failures (TTFs) and Time to Repairs (TTRs) of the trucks were analyzed with this test technique and then whether they were identical or not was determined. In order to determine whether the trucks identified to be identical at the end of this test displayed the same mining performances within the same open pit transportation system, the availability analysis of the identical trucks was carried out. As a result of the availability analysis, it was observed that the trucks had availability values that were very close to each other. It was also determined that Mann-Whitney U test could be employed together with availability analysis. Finally, it was observed that Mann-Whitney U test for two samples could yield rapid results in the performance analysis of complex systems like open pit mines.

Jan 1, 2010

By D. M. McFarland

IN mining, quarrying, and construction, drilling and blasting have an important influence on the operations that follow. If the fragmentation of material being disrupted is inadequate, loading and transportation equipment will not operate at or near full capacity. Any operator faced with this difficulty should not be satisfied until he is convinced by a careful study of his methods of drilling and blasting that no improvement can be made. Rock in a certain quarry in Ohio seemed to defy any grade of explosive or means of detonation that the explosives industry had to offer. The average result of a blast was that a great part of the burden would be pushed out from the face in a number of large sections that would jokingly be referred to as "boxcars." These were no credit to the explosives man and a costly problem for the quarry company. Such blocks retard shovel operation as they have to be uncovered and subjected to secondary drilling and blasting which, if extensive, is an expensive operation. It was an attempt to improve the fragmentation obtained in primary blasts that led to the development of milli-second-delay electric blasting caps. The reasoning that prompted the trial was that even with wide spacing of the drill holes it seemed that the burden was separated too quickly from the face by the cutting action of the explosives from hole to hole. If the time of firing of the holes could be regulated so that

Jan 1, 1948

Reduce the respirable dust exposure of the roof-bolter operator when downwind of the continuous miner, particularly in mines where respirable dust standards are more stringent because of silica in the respirable dust. Dust Sources If roof-bolter dust levels are excessive, the bolter dust collector should first be checked to ensure that it is operating properly. (Technology News No. 219 provides information on how to spot and repair bolter dust collector problems). If the roof-bolter dust collector is operating properly and dust levels are still excessive, then the source is most likely a continuous mining machine operating upwind. In many sections, the roof-bolter operator must work on the return side of the continuous miner during part of the production cycle. In three-entry longwall developments with single split ventilation, this may happen as much as one-third of the time. Factors which pro-mote high quartz dust exposure are:

Jan 1, 1985

By Richard Collins

The projected depletion and the increasing costs of petroleum and natural gas along with the public and governmental resistance to nuclear energy have caused coal to emerge as one of today's answers to both our short term and long term energy needs in power generation. In order to satisfy this need, major increases in coal production are mandatory, thus requiring more and higher capacity coal transfer terminals. The logic for selecting coal as the major fuel for power generation is based on many different reports on the existing and potential energy sources, which include petroleum, natural gas, hydropower, solar, geothermal, and nuclear. The following is a brief synopsis of these reports for each type of energy.

Jan 1, 1978

By CEM SENSOGUT, OZER OREN, YASAR KASAP

The mining sector, which is important in terms of raw-material and energy supply, is seen as a sector with high number of fatal accidents compared to other sectors. In this century of heightened occupational health and safety awareness, it is important to review past accident statistics and analyze current deficiencies using the information in inventory. Although there are many studies assessing occupational accidents occurring in the mining sector, there are few studies using the nonparametric linear programming method. There are many input and output parameters related to occupational health and safety. Nonparametric linear programming method has been found to be useful because it provides simultaneous evaluation of these input-output parameters, does not require functional form in the analyses and provides guidance on the improvement needed by the related parameter. However, this method analyzes data using a single period of time and does not take into account any changes in efficiency over time. In the literature, there is no study in which the change of occupational accidents occurring in mining and even other sectors over time is examined and the Malmquist total factor productivity index (MPI) is used. Within the scope of the present study, the aim was to examine the change of occupational accidents occurring in Western Lignite Corp. in Turkey, where underground and surface production methods are applied, between 2005 and 2018. It is the first time MPI is used to examine the change of occupational accidents over time. The DEAP 2.1 computer program written by Coelli [1] was used in the solution of the models [2].

By Mike Lewis

"Descending several stories down a metal staircase into a shaft spanning a quarter city block -- soon to become Roosevelt Light Rail Station in Seattle, WA -- visitors are greeted with four perfectly round, precast concrete-lined horizontal holes leading deep into the earth. The sound of water trickling out from a small drainage trough can be heard over the faint echoes of construction within. Upon entering, the light is dim, but the air is clear with barely a dust particle flowing through the sunbeams. This type of air quality is only accomplished with diligent controls, and JCM Northlink, the company in charge of building the Northgate Link Extension Project, is taking those measures seriously.Commissioned by Sound Transit, JCM is a joint venture of three companies: Jay Dee Contractors, Frank Coluccio Construction Co. and Michels Corp. The tunnels JCM constructed are intended to provide fast, reliable underground rail service, as well as relieve one of the region’s most congested traffic areas. The $440 million project will connect the Northgate, Roosevelt and University District neighborhoods north of Seattle to the downtown corridor and SeaTac airport further south.The scope of this project includes excavation for two light rail stations, boring of two parallel 5 km- (3.3-mile) long light rail tunnels in six runs and the construction of 23 cross passages. Begun in 2014, Sound Transit estimates that crews excavated more than 382,000 m3 (500,000 cu yds) of soil and installed 7,352 precast concrete tunnel liner rings during the shaft construction and boring phase. Now that tunnel boring is complete, JCM is in the process of constructing the cross passages, which act as maintenance areas and escape routes for passengers. Throughout the entire process, the company has utilized atomized mist to control particle emissions.“Our dust control needs change at every phase of the project and don’t go away until the project is fully complete,” said a JCM safety representative. “We found that different dust suppression technologies were needed at different intervals, but atomized mist seemed to fulfill our needs at every step.”"

Jan 9, 2017

By D. J. Senor

Closed chamber incineration (CCI) is a novel technique by which irradiated nuclear graphite may be destroyed without the risk of radioactive cation release into the environment. The process utilizes an enclosed combustion chamber coupled with molten carbonate fuel cells (MCFCs). The transport of cations is intrinsically suppressed by the MCFCs, such that only the combustion gases are conducted through for release to the environment. An example CCI design was developed which had as its goal the destruction of graphite fuel elements from the Fort St. Vrain reactor (FSVR). By employing CCI, the volume of high level waste from the FSVR will be reduced by approximately 87 percent. Additionally, the incineration process will convert the Sic coating on the FSVR fuel particles to SiO2, thus creating a form potentially suitable for direct incorporation in a vitrification process stream. The design is compact, efficient, and makes use of currently available technology.

Jan 1, 1994

By H. L. TERWILLIGER

THOSE of us who have been following rock drilling work for the last 15 or 20 years can recall some of the problems that were encountered with the old piston type of rock drill and the solid steel which it used. There was frequent trouble in keeping a straight hole in badly broken ground when using the ordinary four- point bit that had a flare on the wings of about 14". The drill steel, when pounding down its hole, would follow the line of least resistance and draw away from the desired line when it encountered a weak side in the ground through which it was drilling. Some would overcome the difficulty by making long winged bits to prevent the steel crowding over; this would relieve the troubles to a great extent. There was trouble with the rifling of drill holes and inability to drill round holes in some ground. The cure for these ills was to use the "X" bit, rather than the crossbit. The "2" bits were brought out in an effort to make it easier to drill a round hole in bad ground. Most of these troubles were before the days when the mechanical drill sharpener was in as common use as it is today. It was not until the introduction of the Leyner type of rock drill, requiring hollow steel that the users of rock drills found themselves confronted with more difficult prob- lems than they had ever encountered before with drill steel because the steel had to stand more severe service.

Jan 1, 1924

By J. B. Malcolm

The discovery of tungsten-bearing quartz outcroppings in Vance County, N. C., by the Hamme brothers in 1942, made international news in the mining industry and was, in fact, one of the major ore discoveries made in the U.S. during the last 25 years. Operations began at the Hamme mine in 1942, but after 16 years of successful operation, the mine was closed down in 1958 under adverse market conditions. By that time, it had produced nearly 20 million lbs of metallic tungsten. Because of the square-set timber mining method then in use, mine operating expenses were high, actually representing 78% of the total operating expenses at the property. In timber work alone, 160 men were employed. Approximately 500,000 bd ft of timber were placed monthly at a direct supply cost of $1.00 per ton of ore mined. Late in 1959, following a slightly improved position in the tungsten market, company management decided that, by changing the mining method, the operation could be economically feasible. The major premise in this decision was that a reduction of from 25 to 30% of the mining costs could be achieved by the conversion of the mining method from square-sets to horizontal cut and fill. Reopening of the mine began in February 1960, Full production has now been reached and overall mine productivity has been doubled.

Jan 1, 1962

By N. A. D. Parlee, E. M. Sacris

OVER 55 years ago, Sieverts and Hagenacker1 and Donnan and shaw2 made determinations of the solubility of oxygen in liquid silver, over a rather short range of temperatures (973° to 1125°C), using quartz bulbs, mainly at 1 atm. From the results of their investigations, Mizikar, Grace, and parlee3 plotted % O vs 1/T and obtained the following straight-line equation for solubility at 1 atm: log % O = 723.7/T - 1.0949 Recent work on the kinetics of the Ag-O2 system394 indicated there might have been some error due to reaction with the direct heated silica bulbs. Thus it became important to redetermine the solubility with the silver contained in a better refractory such as alumina, and by induction heating where the walls of the container were not so strongly heated. It was also desirable to extend the temperature range. A modified Sieverts apparatus of fairly standard type was used except that a special type of reaction tube was employed, Fig. 1. Dried argon with a guaranteed purity of 99.9 pet, and dried medical-grade oxygen with a guaranteed purity of 99.6 pet containing a little nitrogen, were the gases used. The measuring system consisted essentially of a manometer and a water-jacketed 100-cc gas buret with an open-end vertical tube parallel to the buret. This tube has the same diameter as the buret in order to give the same capillary effect on the mercury. A screw leveling device was used with the buret leveling bulb to help provide accurate pressure readings. A 2-mm ID capillary line connected the buret to the reaction chamber, helping to reduce the dead volume, which was determined with argon. The heating medium was a 2.5-kw output induction furnace. The induction coil was made of a 3/16-in. copper tubing with eight turns and an inside diameter of 4 cm. The reaction bulb was made of a quartz tube 18 cm long and 3 cm in inside diameter, Fig. 1. Inside the quartz tube were two alumina crucibles (Mor-ganite Triangle RR, XN10 and XN5) one inside the other. Below these two was an alumina disk. The disk prevented the corners of the outer crucible from expanding against the quartz tube. The solid sample (99.994 + pet Ag), which had been previously cleaned by air oxidation and repeated removal of scum, was placed inside the inner crucible. An alumina disk with a hole at the center covered the two crucibles. In order to decrease the dead volume, an evacuated quartz "filler" tube was placed on top of the crucible cover. The part of the reaction tube above the spherical joint was made up of Pyrex glass with a flat glass top. It was here that a prism was placed to facilitate the use of an optical pyrometer, previously calibrated at the freezing point of silver. This type of reaction bulb and furnace assembly was specially designed for this work, and used in preference to the relatively new water-

Jan 1, 1965

By Albert E. Keller

This paper describing the timekeeping and pay-roll methods of the Britannia raining and Smelting Co. (Ltd.) is one of a series being prepared for and published by the United States Bureau of nines regarding office procedures in connection with mining operations. The general office of the Britannia Mining and Smelting Co. (Ltd.) is located at Britannia Beach, B. C., a town of about 600 inhabitants at tidewater on the east side of Howe Sound and about 30 miles from Vancouver, B. C. The Beach, as it is locally termed, is a company town consisting largely of about 250 employees of the company and their families. Here is the milling and concentrating plant of over 6,000 tons daily capacity- the main service units comprising the electrical, mechanical, blacksmith and woodworking shops and the local electric-furnace foundry; the central-heating steam plant; the air and electric generating units; the ball-manufacturing plant; the warehouses; and the general store, which serves this community and also acts as distributor for the general stores located elsewhere on the property.

Jan 1, 1932

By Peter A. Hacquebard

Recent drilling programs have shown that the in-situ coal resources of Nova Scotia are very substantial. The grand totals of the measured, indicated and inferred categories amount to 232 m, 646m and 993 m tons, respectively. This vast quantity of coal occurs essentially in five main fields: Sydney, Mabou, Port Hood, Pictou and Springhill. The largest resources (84% of the total) occur in the submarine area of the Sydney coalfield. With a 65% recovery rate, there are at present 150m tons of proven, recoverable coal in Nova Scotia. At a predicted maximum annual production of 5 m tons, this amount equals a lifespan of 30 years. However, additional drilling, particularly in the Sydney offshore area, holds promise of increasing the recoverable reserve tonnage to at least 350 m tons. This figure may be compared with the 484 m tons production obtained during 191 years of mining (from 1785-1976). The geological appraisal of the remaining coal resources in the five fields mentioned is presented in three-dimensional diagrams, per individual seam and corresponding reserve area. In addition, the submarine extensions of the Sydney and Mabou coalfields are discussed in light of results obtained from off shore oil exploration wells. The terminology and standards of coal resource calculations are pointed out, and the phenomenon of seam splitting and its prediction from geological data is illustrated. The availability in Nova Scotia of either thermal or metallurgical coal is considered in relation to rank and sulphur content. This paper was presented in June 1977 at the 90th Annual Meeting of the Mining Society of Nova Scotia. The coal resource estimates, however, have been updated to include the results obtained with the offshore drilling in the Sydney Coalfield to November 1977.

Jan 1, 1979

The London Metal Exchange began its first official session of aluminum trading on Monday, October 2, LME prices based on 3-month forward contracts opened Monday at 52.4 cents per pound, fell midway through the week to 52.3 cents and ended Friday at a high of 52.7 cents. For the week, LME metal averaged 52.5 cents. Although Reynolds Metals Co. and Aluminum Co. of American continued in September to value unalloyed 99.5 percent aluminum ingot at 53 cents per pound, other producers were at higher positions of 55-57 cents. Alcan Aluminum Corp. of Alcan Aluminum, Ltd., a Canadian producer, increased prices for its U.S.-marketed ingot by 2 cents to 55 cents per pound, effective September 21. New York merchants increased ingot quotes by approximately 0.5 cents to 52.8-53.5 cents per pound.

Jan 1, 1978

By R. E. J. Putman

Rising demand, artificial market conditions, increased overseas competition, and a fluctuating international situation have brought ever increasing pressures to bear on the nonferrous metals industries, and particularly in the United States, Although capacity is being expanded by the construction of new plants and the development of new ore deposits, increasing attention is being focused on the possibilities of improving the performance of the existing installations and of getting the most out of the new equipment now installed. At first sight the task appears formidable. Based on raw materials which are nonhomogeneous, and possessing characteristics which are hard to quantify, even the processes by which the values in the ores are concentrated and extracted are in many cases not fully understood. The necessary analytical equipment and transducers demanded by these industries have also been slow in development and their earlier absence has hampered the application of modern control technology, This is reflected in plants which have been designed for ease of manual rather than automatic control, and in which the application of control techniques at first sight appears economically prohibitive. However, in any industry progress often comes only in small steps, It may be that by the wise choice of limited objectives and perhaps only partial solutions, substantial improvements in plant performance can be implemented now, and with only a modest investment. If modern control equipment is chosen of the type which can be reprogrammed, advantage can be taken later of more sophisticated solutions as the technology of the industry advances. This task of improving plant performance can and must be commenced even though our knowledge is incomplete. The experience of a related mineral consuming industry, with similar problems in the past, can be encouraging.

Jan 1, 1967

By D. Scott Scovira, Thomas Gustavsson

Exiting WW2, the potential of nitrates and hydrogen peroxide for application as industrial explosives both became known. The technology stream advanced the development and uptake of nitrate-based explosives to the point that they are the current global standard for blasting. Recently environmental issues are influencing the strategic agenda of extractive industries. The mid-2010s saw renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the 2020s provided additional impetus to investigate hydrogen peroxide-based explosives. Hypex Bio is at the forefront of developing and delivering bulk gas sensitized Hydrogen Peroxide Emulsion (HPE) for blasting. HPE consists of hydrogen peroxide along with smaller amounts of fuel and emulsifier. The consistency of HPE is similar to industry- standard nitrate-based emulsions. It is compatible with existing priming and initiation systems. HPE does not contain nitrates and thereby does not produce post blast nitrous oxide fumes nor discharge of nitrates or ammonia to mine water. Importantly, HPE contributes to reduction in total carbon emissions as compared to nitrate-based explosives.

Feb 1, 2025

By Scott Ellenbecker

Mining has evolved in recent years, taking steps forward in the way that the industry is considerate of the environment and the communities in which it operates. Technology plays a major role in that evolution. Osisko Mining?s Osisko Mine near Malartic, Quebec is developing a new way of doing business. One manager said, ?We are building the Osisko culture,? but the company is doing many things that could become industry changers. Much of the change is driven by mine ownership and management to offer a better workplace and better community relations. Mining equipment manufacturers are changing, too, by engineering products with more operator comfort, fuel economy, ease of maintenance and more cleanly designed machines. And for those drills working close to communities, smaller bore sizes and sound retention are just two changes for the better.

Jan 1, 2012

By M Akhtar, E Jak, M Shevchenko

This article presents an overview of the experimental phase equilibria studies of S-containing systems (Ni-Sn-S, Cu-Sb-S, and Cu-Sn-S) and As-containing systems (Fe-Sb-As and Fe-Sn-As). These systems improve the prediction capabilities of FactSage in a 20-component ‘Cu2O’-PbO-ZnOFeO- Fe2O3-CaO-SiO2-S-(Al2O3-MgO-CrO-Cr2O3-Na2O)-(As, Sn, Sb, Bi, Ag, Au, Ni, Co) system for complex pyrometallurgical operations during both refining and recycling. Experiments involved equilibration at predetermined temperatures (300–1200°C) with or without preheating, followed by rapid quenching in a brine. Quenched samples were then directly measured using an electron probe microanalyser. For the Ni-Sn-S system, liquid phases (NiS- and SnS-rich mattes and liquid metal) and solid phases (Ni1+xSn, SnS, Ni3Sn, FCC-Ni, Ni1-xS, NiS2, Ni3Sn4, SnS2, Sn2S3 and β-Ni3S2) were observed. A new Ni3Sn2S2 phase was found to melt incongruently. For the Cu-Sb-S system, liquid metal, matte, FCC-Cu, digenite, Sb, CuSbS2, Cu3SbS3 and Cu3SbS4 phases were observed. For the Cu-Sn-S system, liquid metal, matte, digenite, SnS and Cu3Sn phases were found at liquidus.

Jun 17, 2024

By Jr. Napolitano, Jr. Sanders

"Morphological evolution of a dendritic growth front in a binary alloy is simulated using a cellular automaton approach to establish the feasibility of modeling such growth with a local rule-based scheme. The motivation for this work is derived from the need to predict the development of solidification structures within real components of complex geometry, where significant constraint of the thermal and solutal fields may exist. Such cases present complex boundaries and large domain sizes, which may preclude the effective use of more conventional methods. In this work, a model is presented which couples a two-dimensional alternate-direction-implicit finite-difference diffusion solution with a cellular automaton growth algorithm to simulate morphological evolution in alloys solidifying under directional growth conditions. Temperature, composition, and interface curvature are incorporated into a local growth potential which is used by the automaton, allowing the interface to evolve. Alloy solidification is simulated over a range of experimental conditions, producing various structures. Issues addressed include morphological instability, primary spacing selection, interface curvature, microsegregation, and tip conditions.IntroductionThe development of dendritic structure plays an essential role in alloy solidification. Virtually every microstructural feature, within a cast alloy component, is related to the interface morphology present during solidification. Conventional solidification theory, describing dendrite tip kinetics and mushy zone phenomena, provides a means for estimating overall microstructural parameters for an alloy solidified under steady-state conditions. Microstructural prediction for actual components, which are finite in size and complex in geometry, requires a description of the evolution of the interface morphology under transient conditions and geometrical constraint and an understanding of how the structure propagates through the mold. Any useful simulation tool must be equipped to handle these circumstances within the limits of computational feasibility."

Jan 1, 1998

By P. Patnaik, F. Cuneo, D. M. Wang

Microwave (MW) energy has been used widely for several decades for communications, food processing, wood drying, vulcanization of rubber and medical therapy. Recently, this technology was found to be capable of successfully sintering ceramic and metallic powder materials, with the advantages of reducing soaking times and sintering temperatures. Unlike conventional heating, MW radiation works through the absorption of the microwave energy by a material placed in an electromagnetic field within the microwave cavity. A far more efficient heating process is produced due to the unique ability of microwaves in selectively heating a pecific part of the material with desirable dielectrical properties. This exploratory research was initiated with the objective of locally sintering the thermal barrier coating of gas turbine components using MW radiation. This novel technique may allow repairing of the component without subjecting the entire piece to unnecessary elevated temperatures and reduction of process time and cost. Y ttria stabilized zirconia was used in this study and sintering was conducted using a multimodal 1.2 kW microwave facility. Three configurations of heating setup were experimented and the preliminary results will be discussed in this paper.

Jan 1, 2006