Search Documents

By T. Resende, J. Sismour

"Signs in underground mines are subject to variable airflow, which carries dust and moisture. Dust buildup reduces their visibility, hampering production efficiency and safety. Underground workers commonly must stop to clean signs in order to gauge their location, or find critical supplies or services. There are currently a variety of coating products, including dust and water repellants, available on the market that have the potential to reduce dust accumulation on sign surfaces. This paper describes a preliminary study to determine their effectiveness. The study involved a practical testing protocol using a trickle rock duster and samples cut from a clean, used road sign. Product effectiveness, under both dry and wet conditions, was evaluated based on photographic evidence by comparing changes in sign luminosity after a period of rock dust application. By analyzing the frequency of different pixel luminosities on the dust-covered samples, both uniformity of dust coverage and the total amount of accumulation was assessed. Results indicate that at least one product may reduce the amount of dust buildup on sign surfaces and increase visibility. INTRODUCTION In all underground mines, visibility of signage is critical. Signs inform miners of their location, direction toward escape routes, and location of supplies. Over time, sign surfaces can collect dust and can eventually become unreadable. The rate of dust accumulation on surfaces is often particularly high in coal mines, where both mining (e.g., cutting and drilling) and rock dusting activities can contribute significant amounts of dust to the airways. Several factors may contribute to dust buildup on sign surfaces. First, basic principles of fluid and particle flow are at play. When a fluid travels past a stationary surface, the velocity of the fluid at the surface boundary is zero. If a very small dust particle moving with air collides with a surface, it does not immediately fall off since the air velocity is zero at the sign surface. (This is the same reason that dust can collect on a rotating ceiling fan.) Further, once the collision occurs, other mechanisms may help keep the particle there – including friction that resists particle falling due to gravity, and adhesive forces due to humidity and/or static charges the particle and others already on the surface. Currently, the most common way to deal with reduced sign visibility due to dust buildup is for mine personnel (e.g., a compliance foreman, supply worker) to periodically clean sign surfaces – usually just by wiping them with a cloth. As a regular activity, this solution is inefficient; in cases of emergencies, it can also pose unnecessary risks. Application of an off-the-shelf coating to sign surfaces may represent a simple yet effective way to reduce the rate of dust accumulation. There are currently a variety of products on the market that may be suitable for this purpose, including dust and water repellants."

Jan 1, 2017

By F. J. Wiebel

"INTRODUCTION As a result of a general survey of the iron-ore deposits of Califor¬nia, the Bessemer was one shown to offer possibilities of developing com¬mercial ore reserves. Surveying and exploring were done at the request of Congress for an investigation of raw materials for the production of steel.A wartime steel plant has been established at Fontana, San Bernardino County, and a backlog of iron-ore reserve for the maintenance of permanent steel industry on the West Coast will be of National benefit in the postwar period.W. D. McMillan, a mining engineer the Bureau of Mines, examined the property in May 1942, and it was reexamined by D. W. Butner, also of the Bureau, in October 1943. Geophysical work was done by the Bureau in 1944, and the property was explored by diamond drilling from April to August 1944 and February to SeptemberACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, under the direction of R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

May 1, 1947

By M J. Dunn

The geotechnical model is the cornerstone of any mining geotechnical design and as such the confidence level and reliability of the geotechnical model is paramount. The geotechnical model confidence level needs to be commensurate with the level of design that is being applied or study that is being undertaken. The geotechnical model is made up of several components and the reliability of the data underlying these components ultimately determines the reliability of the geotechnical model.Data reliability is linked to the quantity of data collected, the spatial distribution of the data collected, quality of the data collection and the interpretation of the data. In a typical project, there is an opportunity to improve data reliability through the scoping, prefeasibility, feasibility and final design and implementation stages.Currently, very little quantitative guidance exists in the literature on assessing the confidence level of geotechnical studies, although there have been attempts by various authors (Haile, 2004; Haines, Swart and Kruger, 2006; Read and Stacey, 2009; Dunn, Basson and Parrott, 2011) to qualitatively describe what level of geotechnical data is required. Recently a number of authors (Read, 2013; Fillion and Hadjigeorgiou, 2013; Thomas, 2013) have outlined methods that could be applied to assess the reliability of some types of geotechnical data that are used in the development of geotechnical models.This paper briefly discusses some of the factors influencing data reliability and the geotechnical model confidence and some of the tools available.CITATION:Dunn, M J, 2014. Geotechnical models and data confidence in mining geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By A. V. Aleksandrov, T. N. Aleksandrova, N. V. Nikolaeva

Using complex thermal analysis methods, flotation concentrates were classified depending on what the organic and nonorganic carbon form is. The possibility of ultrafine particles of valuable components (noble metals and diamonds) extraction using physical actions of different genesis in the processing of ‘unconventional’ mineral raw materials is considered in the paper. Electromagnetic treatment is one of new technologies in the field of mineral processing. The features of the electromagnetic effect on substances include uniform heating throughout of the volume, high speed and low inertia of heating, as well as the possibility of selective heating. A selection of studies including gravity, flotation and extraction methods of enrichment using energy effects, as well as thermal analysis was conducted to establish the availability and possibility of extracting valuable components. Due to microwave and high-temperature exposure, minerals and gas-liquid inclusions are decremented, and crystal-chemical water is released, resulting in additional defects. As a result, self-cleaning of sulphide minerals from atoms of scattered gold occurs by distilling it into peripheral parts of grains and intergranular space, where ultradispersed individuals are formed. Keywords: Refractory gold-bearing ores, physico-chemical properties, ore preparation, flotation, modelling, simulation, selection

Jan 1, 2020

By K. Ogawa, T. Yokoyama

Hydraulic fracturing technique, an applied technique to cause tensile fractures to rock by injecting water pressure to a certain closed section of the borehole, is a measurement method of in-situ rock stress. This technique has the highest track record for techniques used in sub 1000 meter. A feature of this technique is comparatively simple and easy for in-situ stress measurement, because the measurement is applicable when a drilled borehole is available. The predominant advantage of this method is that elastic constants such as Young’s modulus and Poisson’s ratio are not required for determining the value and direction of initial stress. The factors to determine the stress state are the water pressures of re-opening and shut-in of fractures around the borehole wall and its directions. With conventional methods, however, the accuracy of the derived stress states from the observation equations was often adversely affected by the lack of consideration of the remaining water pressure in fractures and insufficient stiffness of the pressurization system. We have developed a new hydraulic fracturing system based on a new test method concept overcoming these defects, and applied to a 300 meter deep borehole in granite. The most important improvement of the new system is an employment of a syringe pump which enables an accurate flow control of fluid with less than 1ml/min in the pressure of 30MPa. Therefore the new test system has a quick response for pressurising in the interval zone, and the measured data was confirmed extremely accurate.

Jan 1, 2015

By Krogerus. H., P. Jokinen, T. Lintumaa

Keywords: Pyrometallurgy, furnace, coke, smelting charge, optimization, ferrochrome The main consumer of ferrochrome is stainless steel production. Stainless steel must maintain a reasonable price against other competitive materials. Therefore, the ferrochrome price must be low enough and profitable for the producers of stainless steel. The investment and operational costs of ferrochrome production are greatly dependent on the availability of the process and the production rate. Thus the furnace size and production rate in submerged electric arc furnaces will be greatly increased in the near future. The ferrochrome production per furnace, e.g. at Outokumpu?s Tornio Works, increased from 30 000 t/a to 165 000 t/a in about 35 years. The same trend will continue globally but now much more quickly. The Outokumpu ferrochrome process at Tornio Works uses sintered chromite pellets and upgraded lumpy ore as a chromite source. Metallurgical coke is used as a reductant. Reliable smelting in a large furnace demands the correct charge composition and well-known characteristics of the charge components. The quality and electrical conductivity of cokes (normally used) has the most important role for the electrical conductivity of the smelting charge. The results of the measured electrical conductivity of different cokes and the smelting charge with many controlling factors are presented here. These measurements were performed over the years for our own purposes at the laboratory of Outokumpu Research Oy (ORC), in Pori, Finland.

Jan 1, 2006

By Donald L. Brothers

"OUT IN BRITISH COLUMBIA, we have a legendary creature called ""The Sasquatch,"" a large ape-like creature which, according to those who claim to have seen it, somewhat resembles the Abominable Snowman of the Himalayas. Through the years, the legend bas been perpetuated by hunters and prospectors who return from remote wilderness areas with fantastic tales about hairy creatures, twice the height of an average human being, who leave 2-ft-long footprints in the soft forest floor. However, the existence of this creature bas never been proven and the attitude in British Columbia circles is that the whole thing constitutes either a great discovery or a giant hoax, and is about equally unbelievable either way.The Sasquatch, however, is not the only giant in British Columbia. If you find the Sasquatch story un-believable, you'll fi nd it just as hard to believe what is happening in the mining industry out west. We have opened four new mines so far this year (1967), another mine is expected to be brought into production before the end of the year and any mining man will tell you it's just the start of a mining boom which will continue for many years if metal prices are maintained and the federal government sees fit to discard the taxation changes pro-posed in the Carter Royal Commission Report regarding mining."

Jan 1, 1968

By Peter Deming

"PART 1 OF 2INTRODUCTIONSlurry trenches are the least cost hydraulic barrier available, if the excavated spoils can be recycled into backfill. As such, slurry trenches are constructed where possible, sometimes at high risk. Slurry trenches are also used to install biopolymer drainage trenches, which have a low safety factor because the biopolymer slurry weight is marginally greater than the weight of water. In marginal ground the construction risk falls to both the Owner who designs and asks for the construction, and the Contractor who manages the work and promises to complete the project successfully. This paper discusses design and construction of slurry trench barriers in marginally stable ground and where groundwater chemistry invokes the need for slurry management details to obtain proper backfill placement.As a designer, Mueser Rutledge Consulting Engineers works for both Owners and Contractors. We are usually able to convince Owners of their responsibility for design detailing in order to obtain a working final product and to obtain reasonable bids from Contractors by disclosing construction needs and designing to reduce the contractor’s exposure. We often work for Contractors to produce designs which result in successful construction in projects where the Owner’s engineer places the responsibility of design and construction on the Contractor.This paper is intended to inform both Owner and Contractor audiences of resources which are available to reduce the risks of trench collapse in difficult ground conditions. We hope it serves this purpose.DESIGNSubsurface InvestigationsSubsurface conditions should be defined by borings focused on definition of the soil profile and soil design parameters. After general subsurface conditions are defined, barrier borings should be drilled along the final alignment.Definition of Soil Strength and CompactnessCompactness of sand and gravel strata should be defined with Standard Penetration Test N-values. The shear strength of cohesive materials should be defined by laboratory testing. Silt and fine sand strata with little cohesion should be investigated using mud rotary techniques to prevent disturbance. General strength characterization by soil layer should be used for analysis of trench wall stability."

Jan 1, 2006

By Meili Zhu, Qingpu Shi

High temperature, methane, dust and other disasters are getting more serious with mining depth getting deeper and the development of mechanization in underground mines. An application of a descensional ventilation to a coalface is one of the effective measures to solve the above problemes. The descensional ventilation is an venttilation that an airflow in a coalface wouuld downflow along an inclination of a coalface and the direction of the airflow is the same as coalflow. Since 1960's, the descensional ventilation has been applied to 171 coalfaces in 46 coal mines of 23 coal mine administrations in China, such as Pingdingshan , Zhongliangshan, Pubai, Huangshi coal mine administrations. Among the 171 coalfaces, there were 104 coalfaces taking 60.8% in gently inclined seam. The coalfaces in inclined seam and steep seam were individually taking 18.7 % and 20.5 %. There were 77 coalfaces taking 45 % of the total in low gassy coal mines and coal and methane outburst mine were individually taking 17% and 38%. There were 141 coalfaces taking 82.5% of the total in potential danger of dust explosion. There were 125 coalfaces taking 73.1% of the total in potential danger of spontaneous combustion. Therefore, the descensional ventilation can be used in coalfaces under different conditions in China. The practice at home and abroad shown that the application of the descensional ventilation to coalfaces has obvious results in dust control, temperature control, preventing methane accumulation at top corner angle and control of spontaneous combustion in goaf. To more safely and reliably apply the descensional ventilation to coalface and to provide a way for the development of mine ventilation technology in China, the paper will have discussions on the following problems: METHANE EMISSION AND DISTRIBUTION AT COALFACE WITH DESCENSIONAL VENTILATION Methane emission in a coalface with a descensional ventilation is an argued issue for many years. Base on the coal practice, special similar model tests and researches in China, the followings are our main comments. The Descensional Ventilation can Reduce the Methane, Accumulation at the Top Corner Angle. The measurements in six coalfaces with the downward airflow in Qinhemen Mine, Fuxin Coal Mine Administrations shown that the methane concentration at the top corner angle is often up to l% when the coalface has the upward, airflow. The max. methane concentration at the top corner angle is about 0.49 to 0.7% when the coalface has the descensional ventilation. Therefore, with the descensional ventilation, it basically solved the overlimited gas concentration at the top corner angle which is a potential danger to coal production. Because the direction of upfloating gas is opposite to the direction, of the descensional airflow, the descensional ventilation; could increase a turbulent flow mixing capacity of the methan gas and air, and reduce a possibility of methane; accumulation. Due to an air leakage in goat when the coalface with the descensional ventilation lower than an air leakage in goat when the coalface with the, ascensional ventilation, a less methane quantity will release from goat at the descensional ventialtion. It should be pointed out that due to a higher air leakage at ascensional ventilation and the direction of the air; leakage same to the direction of the natural upfloating methane in goaf, those will cause a large methane; accumulation at the top of the goaf and easy bring about, methane accumulation and overlimited methane concentration at the top corner angle with an ventilation vortexflow at the top corner angle. On the other hand, because the direction of the upfloation force function is upward, the descentional ventilation could minimize as possibility of methane accumulation at top corner angle in coal with the descensional ventiltion.

Jan 1, 1991

By Karl C. Dean

To assist in the reduction of environmental degradation resulting from milling operations, the Bureau of Mines has developed, and successfully demonstrated, chemical, vegetative, and combined chemical-vegetative procedures for stabilizing milling wastes under varying environmental conditions. Costs of achieving reclamation using these stabilization procedures are compared with those of other physical and vegetative approaches. The Bureau's chemical-vegetative procedure for establishing vegetation directly on fine-sized wastes compares favorably with other stabilization processes that have been used.

Jan 1, 1972

By R. Charlier, G. Radioti, J. -P. Radu, S. Delvoie, F. Nguyen

"In order to investigate the fracturing of the bedrock and its possible heterogeneous distribution in situ, four boreholes equipped with double-U geothermal pipes of 100 m long were installed on the campus of the University of Liege (Liege, Belgium) over a surface area of 32 m². The bedrock, which starts at a depth approximately of 8 m, is quite fractured and consists mainly of siltstone and shale interbedded with sandstone.Different geophysical methods are applied at two different phases, after drilling the boreholes and after injecting the grouting material. The first approach consists in lowering an ultrasonic borehole imager (borehole televiewer; Zemanek, Glenn, Norton, & Caldwell, 1970), an instrument that acts as an ultrasonic transducer and receiver, into the boreholes to obtain high-resolution, continuous images with 360° coverage of the local geology and fracturing. Moreover gamma-ray logs of the four boreholes are obtained and inclinometry is conducted.After drilling the boreholes fiber optic cables are attached along the pipe loops and the double-U pipes are installed inside the boreholes. Then the grouting material is injected. The second approach consists in measuring the temperature along the fibers by applying the Distributed Temperature Sensing technique (Soto, Sahu, Faralli, Bolognini, Di Pasquale, Nebendahl, & Rueck, 2007). A laser pulse is injected into the optical fiber and the temperature along the fiber is determined by the intensity of Raman stokes and anti-stokes reemitted signals. Temperature evolution is measured during hardening of the grouting material. Local maxima of the temperature curve are probably due to a local lower thermal conductivity and/or a local larger quantity of grouting material due to gathering of fractures.A detailed fracture characterisation (position, opening, orientation, dip angle) is obtained based on the acoustic signal travel time and amplitude. The fractures are characterised by the same dipping and orientation but significantly vary in number and location in the four boreholes, despite the close distance between them. Gamma-ray data and observation of the cuttings during drilling result in rock identification through depth as well as in determination of the layer dipping. The inclination of the four boreholes tends to be perpendicular to the dipping. The combination of the two geophysical methods as presented provides information useful for the hydro-thermo-mechanical behaviour of the bedrock. The contribution of the thermal behaviour of borehole heat exchangers to bedrock investigation will be further studied by conducting Distributed Thermal Response tests (Fujii, Okubo, & Itoi, 2006). During the tests we will measure the temperature variation thanks to the installed fiber optics. These data will allow us to correlate any anisotropic thermal behaviour to the geological characteristics. The available information could be used for a detailed numerical model."

Jan 1, 2015

By D Nieuwkerk, V J. Absolon

"Screw press technology is an innovative approach to tackling the growing pressure to conserve water and minimise the environmental impact of mineral tailings disposal. The principles of the technology have been known for a considerable period of time in non-mining applications such as water treatment, wastewater (municipal sludge), as well as in the paper and chemical industries for dewatering solids, particularly those containing clays.The screw press represents a viable niche technology for filtering fine and high-clay tailings, without the prior thickening stage, and is capable of producing a filtered product that is sufficiently consolidated and dry enough to provide a product suitable for conveying and dry stacking.The Ishigaki screw press was introduced in 1990 and key features are: continuous operation and excellent availability low wear to plant acceptable flocculant consumption low carbon footprint and low noise levels fully automatic.These features lead to simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, smaller footprint and overall lower capital and operating costs.The amenability of a particular tailing stream to treatment by screw press technology may be determined by test work. Two pilot plant studies are described where this technology has been applied in the mineral industry being flotation tailings from a rare earth (RE) mineral concentrator and coal tailings. In addition, preliminary details are given of an ACARP sponsored research program titled ‘The application of screw press filtration in tailings dewatering’.CITATION:Absolon, V J and Nieuwkerk, D, 2014. Innovative use of screw press filtration in tailings dewatering plant design, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 449–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By Shiro Watanabe

To determine the potentialities of nickel as a substitute for cobalt in catalysts for the synthesis of hydrocarbons from carbon monoxide and hydrogen, RESULTS The maximum oil yields obtained in bench-scale equipment were as follows: Using 100N1:20Mn:100 kaolin:200 diatomaceous earth catalyst, a maximum yield of 133.8 cm.3/m.3 of pure CO+2H2 was obtained from one pass of the feed gas, With a nickel:cobalt mixed catalyst (Ni:Co - 3:7) having the composition 100(Ni+Co):8MgO: 5Th02:200 diatomaceous earth, a maximum of 172.2 cm.3/m.3 of pure C0+2H2 was obtained.

Jan 1, 1951

By Roy L. Grant

The Bureau of Mines investigated the up-and-down method with factorial designs to determine if shorter, and therefore less costly, trial sequences could be used. Although sequences of 50 trials are usually recommended, sequences of 20 trials were arbitrarily chosen for the experiments with permissible coal mine explosives described in this report. These explosives were fired from a cannon pointed into a flammable natural gas-air atmosphere at the Bureau of Mines Explosives Research Center gallery to ascertain their safety properties. The investigation demonstrated that the shorter sequences led to useful conclusions with a reduction in cost of the experimental program.

Jan 1, 1967

By E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Leadership is a critical component to an organization’s safety culture and influences the ways that health and safety is enacted on site. Therefore, it is not surprising that improving leadership will also improve safety. Worker perceptions of management practices are shaped through unique leader-employee interactions over time. However, few details are known about the communicative support (i.e., emotional, informational, and tangible) offered by supervisors and its impact on miners’ perceptions and performance. Using pre and post-interview data with 20 supervisors and 48 workers during six-week interventions, researchers identified positive and negative instances of supervisor support and its implications on worker performance. This paper highlights the common support tactics offered by supervisors and desired by workers to help practitioners identify ways to improve their safety culture and subsequently, the proactivity and compliance of their workforce. INTRODUCTION Supervisory leadership is a critical component to the effective implementation of an organization’s health and safety management system (HSMS). Specifically, supervisors serve as representatives of an organization and their actions are indicative of the organization’s safety culture (Eisenberger et al. 1986). Senior management has been shown to serve as a frame of reference for guiding safe behaviors in the workplace (Mearns et al. 1998) and, more recently, research has related supervisory enforcement to workers’ safety compliance (Petitta et al., 2017). Therefore, it is not surprising that by improving leadership, perceptions of management and subsequent safety outcomes are likely to improve as well (Zohar, 2002). Perceptions of management are shaped through unique leader-employee interactions over a period of time (Hofmann and Morgeson, 2004, 1999). How these unique interactions impact worker performance, however, remains unexamined. As a result, understanding how supervisor-employee relationships operate in high-risk environments is unclear (Mirza and Isha, 2017; Denis et al., 2010). A starting point to better recognize the idiosyncrasies of these relationships is by way of examining the communicative support offered by front-line management and received by industry workers. To this end, this paper uses pre- and post-interview data to study the communicative aspects of supervisor-employee interactions at mine sites. The analysis uses a social support framework to identify positive and negative instances of supportive communication. From interview data with 20 managers and 48 mineworkers, data emerged that shows how supervisors’ unique types of support contribute to workers’ perceptions, motivation, and follow-through of safe work behavior.

Jan 1, 2019

By S. Pollak, J. Rickard

The Long Baseline Neutrino Facility Far Site in Lead, South Dakota is currently under construction and involves drill and blast excavation of the largest and deepest caverns in North America. This paper will review how the geotechnical risks are being managed through careful consideration of excavation sequence, completion of exploratory pilot tunnels, implementation of a robust instrumentation and monitoring program, and validation against the design. Aside from having a cross section of 5,900 square feet and being situated at a depth of one mile, the caverns also employ a unique permanent rock bolt solution which underwent a significant pre-production pull testing program involving varying installation methods and being subject to blast vibrations. The behavior of the schistose rock mass and performance of the ground support are being continually monitored throughout the construction phase.

Jun 13, 2023

By T Vijayakumar, Vipul Dobhada, Rajesh Patel, Swarnadip Dey, Naveen Babu D

The most challenging scope of any bridge project in marine or inter tidal zone is to construct sub structure like well Foundation, group pile, pile cap etc. Similarly, it also affects the marine environment/ecology to a great extent. Understanding the level of difficulties and aiding to provide an environment friendly solution, various options are analysed to overcome these and found mono pile to be the best alternative in this context. Generally, the foundation type of any bridge constructed in river, marine or intertidal zone in India is preferred for group piles. For the first time, monopile is being accepted as the foundation of bridge in India at Mumbai Coastal Road Project. The diameters of the monopiles used in this project are 2.5 m and 3.2 m. Hence, the challenges involved in monopile construction and experiences to overcome it are worth to share. Here, a brief discussion on environmental, geological issues and the needs of monopile as the foundation of bridge has been discussed. Furthermore, the monopile construction stages and confirmation of monopile capacity through different load tests have been elaborated.

Sep 1, 2022

The methods employed for the addition of uranium to steels and cast iron in the Physical Metallurgy Division are outlined. It has been found that the segregation of? uranium is a major problem in aluminum and/or silicon killed steels and that the cooling rate is important in al-lowing the segregate to settle to one area, which can subsequently be discarded. The unsegregated areas were found to be extremely low in total oxygen, acid insoluble aluminum (AizOg) and, in some cases, slightly lower in nitrogen. Uranium recoveries, based on analyses of the unsegregated areas, were quite constant, at about 45 per cent, regardless of the type of uranium master alloy used for the addition. No segregation of carbon, manganese, silicon, sulphur, phosphorous, chromium or copper was observed in these steels. In commercial heats, the recoveries ranged from 7 to? 29 per cent for ladle additions to oxygen converted steel. When the steel was fully deoxidized prior to the uranium addition, recoveries ranged from 49 to 66 per cent, regardless of the steelmaking process.

Jan 1, 1964

By A. Liem, R. L. Johnson, C. Sturgess, E. Kuzub

New challenges in mineral processing arise as high-grade ores become less available and the mining industry is forced to exploit lower grade ores. One of the challenges in beneficiating lower grade ores is the liberation of mineral particles while maintaining control over material management. Lower grade ores need fine grinding to free valuable minerals, but finely divided particles can cause severe problems, such as dustiness and flowability, in subsequent stages of material management. There are at least two approaches that can be taken to resolve this dilemma, both of which relate to particle size enlargement. First, the application of a dust suppressant can be used to control that aspect of material management. The optimal choice of dust suppressant agent depends on effectiveness and cost, both of which can be strongly influenced by the selection of application method. Second, agglomeration combining small particles into larger units-can reduce dust and improve the flow characteristics of the material at the same time. There are several mechanisms that can be employed to agglomerate mineral materials. Although agglomeration adds a new processing step, it is often cost effective. This paper describes these two approaches and their respective challenges, as they relate to a mined ore. We report on modified or newly developed procedures for characterizing mineral ores with respect to material management. On the same material, we use agglomeration processing to capture fines within larger particles and show how dustiness and other aspects of material handling are affected. We conclude by discussing their specific application in accordance with the mineral properties and processing needs.

Jan 1, 2004

By N. Naudé

The theory on particles displacement subjected to upwards and settling movements in water, using a water pulse, is described in literature, but very little experimental data is available to verify these theoretical ideas. The aim of this research work was to visualize the displacement of solid particles in a mixture of water and solid particles created with the aid of water pulses in the Mineral Density Separator. From the literature it is known that lighter particles are subjected to higher levels of displacement than heavier particles, and when the particles then settled down, layers of material are formed ac-cording to the densities of the material. By removing the individual material layers, the materials can then be separated according to their densities. During this study the individual material layers were investigated regarding the density and size distribution in that specific density layer. It is important for this project to have a statistical prediction of the ?real? flow of the particles with different density and size distribution, inside the Mineral Density Separator. The information gathered during this study will be used to show the correlation between a two dimensional model of the particle flow and that of the real three dimensional flow inside the Mineral Density Separator.

Jan 1, 2014