Search Documents

By A. D. Hammond

Vanadium is a transition metal, ductile and silver-gray. It is harder than most metals and steels and it has a good resistance to corrosion. It is stable against alkalis and sulfuric and hydrochloric acids. Vanadium is oxidized in air at about 660° C (1,220° F), although an oxide layer forms even at room temperature. The chemistry of vanadium is noteworthy for the accessibility of the four adjacent oxidation states, 2-5. In aqueous solution, the colors are lilac V2+, green V3+, blue VO2+ and, at high pH, yellow VO42-. Considered to be as abundant as zinc, metallic vanadium is not found in nature, but it is known to exist in about 65 different minerals. Economically significant examples include patronite (VS4), vanadinite (Pb5(VO4)3Cl), associated to the uranium mineral carnotite (K2(UO2)2(VO4)2?3H2O) and in a vanadium mica called roscoelite K(V3+,Al,Mg)[(Si,Al)4O10] (OH)2. Other important vanadium ore oxides are montroseite (V,Fe)O(OH) and corvusite (Na,Ca,K)V8O2.4H2O. Much of the world?s vanadium mine production comes from magnetite-hosted deposits and, to a lesser extent, sedimentary-hosted sandstone.

Dec 1, 2013

By L. W. Kelly

The primary purpose of this paper is to show the appreciable savings that were made by roof-bolting the main west entry of the Kings mine, which was to be the permanent, main haulage road, as compared to the cost of supporting the same roof with peg timbering as first planned. Additional items that might prove valuable to other mine operators are contained in this paper and detailed below. 1. A detailed cost of the system of roof support known locally as the peg-timbering method is given. It consists fundamentally of supporting steel cross bars on pegs inserted into holes drilled in the ribs close to the roof. 2. A method of supporting the roof in caved entries is shown, where such support must endure for an extended period in haulageways and air courses.

Jan 1, 1952

By M. H. Kline, Wing G. Agew

"INTRODUCTION The Watson tract was first prospected in 1908, and ore consisting of concretionary psilomelane and wad was found in the bedded residual clays. A small mill using a log washer and jigs was constructed for concentrating the ores -on the bank of Mudhole Run, and it is reported that a few wagon¬loads of ore were shipped via the Norfolk & Western Railway. The operation was of short duration.During World War I, the area was seriously studied by the Federal Geological Survey and Virginia Geological Survey. The Virginia Geological Survey, in Bulletin 173/ reporting the work, lists the property among the few recommended for further exploration.When the shortage of manganese ores in the United States became imminent, the Bureau of Mines was authorized by the 76th Congress, under the Strategic Materials Act, to prospect and explore for manganese. Upon the recommendation of the Federal Geological Survey, a project to undertake this work was started at the old Watson mine in January 1941 and continued until August of the same year."

Apr 1, 1948

By Shani Engelbrecht, Belinda McFadzean, Avuyile Wali, Natalie Shackleton, Vratislav Malysiak

Frothers play a crucial role in sulphide and PGM ore flotation recovery, and AECI Mining Chemicals studies on PGM ores have shown significant flotation kinetic increases with the optimal frother-collector combinations. Using Senfroth 200 as the industry baseline, remarkable kinetic increases were observed with AECI Mining Chemicals developed frothers in the first concentrate. Even in the worst-case scenarios, 4E PGM recovery increased by 5% at a slightly higher concentrate grade. It is important not to limit frother dosage to a fixed value. Instead, enough frother should be added to maintain a stable bench float, measuring the dosages by frother volume before and after tests. Frothers can be specialized blends and their importance should not be underestimated. The results produced by formulating and innovating frothers to address specific industry challenges have been encouraging. Testing a frother on a plant scale does not have to be as daunting as with collectors, enabling the identification of the best frother-collector combinations at an industrial scale. AECI Mining Chemicals bench scale testwork has motivated plant-scale trials that have successfully transitioned to commercialization. This paper compares the results from metallurgical and froth stability tests and shows that occasionally frothers that have a less stable froth can have improved valuable mineral recoveries, while still exhibiting better drainage for reduced entrainment and mass pull. It was shown that caution should be used when relying only on simplified froth stability tests in the evaluation of new frothers.

Feb 1, 2025

By Andrew J. Gaber

Beginning in 1961 the Coal Research Bureau of the West Virginia University School of Mines began a program of research to investigate the potential of the magnetic separation process to remove sulfur of the pyritic form from pulverized coal. Using a so-called isodynamic magnetic separator (1) it was demonstrated that significant quantities of pyritic sulfur could be removed from coal. Pulverized coal samples representing several different coal seams were individually screened into sizes in the 48 mesh by 200 mesh (297 to 74 microns) range, and untreated and steam-air treated samples of each were processed by the magnetic separator. The results of the investigations to magnetically remove pyrite from coal were published in two separate reports issued by the Coal Research Bureau (2,3), The isodynamic magnetic separator was designed about 30 years ago for use in geological and mineralogical laboratories (1,4,5) to isolate one or more minerals exhibiting only small differences in their magnetic propertiese Specifically, to accomplish this, the air gap of the unit was designed to provide a nearly constant magnetic gradient both laterally and longitudinally in the separating zone. It is reported that mineral concentrates of 99.5 percent purity can-be produced on closely-sized fractions after several cleanings through the unit. The isodynamic magnetic separator, therefore, was not expected to process coal containing sizes smaller than 200 mesh, or to demonstrate commercial capability to process pulverized coal. The primary purpose of the Coal Research Bureau in using the unit was that of determining if the magnetic process could remove pyrite from coal, and thereby encourage further research directed toward development of acceptable full-scale processing equipment.

Jan 1, 1969

By G. V. Henderson

The San Gabriel Valley contains some of the richest and most extensive sand and gravel deposits in California. Operating quarries within the San Gabriel area mine more than 15 million tons of high quality aggregate per year. This represents about 45 percent of the total mined in the greater Los Angeles area, one of the nation's largest aggregate markets and producing regions. Popular opposition to continued aggregate production in the San Gabriel Valley is high, especially in the city of Irwindale where 40 per-cent of the city's property is made up of "excavated holes," some 150-200 feet deep. Reclamation of 70 years of mining is now an almost impossible task. Zoning regulations have the effect of depleting these vast reserves rapidly by changing the definition of total reserves to include only "legally minable reserves." All but two or three of the aggregate mines now operating will be depleted or zoned out of business by the year 2000. Some studies indicate that there will be no aggregate mining operations by 1995. Recent studies show a drastic change in land use patterns within this valuable mineral resource area over the past 20 years. The San Gabriel Valley is a classic example of the lack of adequate regional planning with regard to urban development in MRA's and represents a "too little, too late" effort by local government and industry.

Jan 1, 1978

By Charles Prasky

This report describes and appraises recent progress in the development of a differential sulfatizing process for recovering a ferrograde manganese oxide from low-grade manganiferous ferruginous materials in the Cuyuna range. Individual process steps were carried out successfully using a 20-inch-diameter shaft for continuous countercurrent sulfatization of the manganese, a multiple-compartment rotary drum for leaching the water-soluble manganese sulfate, a submerged-combustion evaporator for the recovery of monohydrate crystals of manganese sulfate, and a shaft furnace for the thermal decomposition of sulfate crystals for production of a ferrograde manganese oxide and a sulfur dioxide gas suitable for sulfatization of fresh are. Of the two general kinds of Cuyuna manganiferous materials--the carbonate slates and the oxidized ores--only the slates were studied at pilot scale.

Jan 1, 1963

By Todd Kilduff, Ryan O’Connell

Pipe canopies continue to gain momentum as a reliable methodology for construction of excavations below critical facilities with minimal surface settlement tolerances, such as railroads or roadways. Two tunnel projects designed by Kilduff Underground Engineering in the Salt Lake City, UT area, each at varying stages of completion, had project design criteria for selection of a tunneling methodology to minimize surface settlement. Both projects consist of a pedestrian tunnel, one crossing beneath a major roadway in downtown Salt Lake City and the second beneath UPRR tracks. Both projects were in difficult, coarse alluvium/fan ground conditions with project criteria that resulted in minimal cover above the tunnel. For each project, a pre-support pipe canopy was designed, requiring the placement of steel, canopy pipes driven the extent of the tunnel length. The pipe canopy is installed using a trenchless technology and then excavated with SEM tunneling and shoring provided by traditional support of excavation methods. The pipe canopy pre-support method offers a low-impact method to install an underpass beneath critical structures by adding significant stiffness to the subgrade to mitigate surface settlement during the main tunnel excavation sequence. These case studies seek to communicate the challenges associated with pipe canopy installation in site-specific ground conditions and explains how these challenges were overcome. This paper aims to define the project risks and describes the pipe canopy methodology as a viable solution to mitigate surface settlement in low cover tunneling scenarios.

Jun 13, 2023

By L. Gertsch, R. Gustafson, J. Rostami, C. Swope

Development of a permanent human base on the moon for exploration requires a self-sustaining system. Such a system entails the production and processing of limited amounts of raw material on the moon. Any mining and construction activities on the moon can only be performed by a robust excavation machine that can excavate a variety of material, from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, a limited amount of information on lunar regolith is available to develop and optimize a machine for lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe, PA. This paper discusses the results of initial material characterization, as well as full-scale tests of a prototype cutterhead in relevant material. A brief review of anticipated production rates under various assumed ground conditions is also presented.

Jan 1, 2010

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By J. Edberg

"This article details the use of an alternative testing method to the 2004 "Post-Tensioning Institute (PTI) Recommendations for Prestressed Rock and Soil Anchors" manual’s recommendations for temporary and permanent rock anchors for applications in shafts and tunnels. This method was developed and used for the Black River Tunnel (BRT) project in Lorain, OH as a means to reduce testing time of rock bolts during shaft construction while maintaining a similar level of quality control and assurance. The following sections will detail the project background, subsurface characteristics, shaft construction, the 2004 PTI testing method and associated difficulties, the alternative testing method and conclusions reached.Project backgroundThe city of Lorain is located in north central Ohio on the south shore of Lake Erie, approximately 40 km (25 miles) west of Cleveland and 119 km (74 miles) east of Toledo. The city chose to build a large-diameter storage tunnel and pump station to meet its requirements to reduce sanitary sewer overflows to the nearby Black River. NTH Consultants Ltd. (NTH) was retained by the city’s prime consultant, Malcolm Pirnie Inc. (now the water division of Arcadis), to perform a geotechnical investigation, develop design and construction bid documents for the tunnel and shaft liner systems and ultimately provide oversight assistance during the construction phase of the project.The BRT is an approximately 1,700-m (5,560-ft) long, 7-m (23-ft) diameter rock tunnel to be lined with a 5.8-m (19-ft) inside diameter secondary concrete lining (Fig. 1). The tunnel is designed to accept flow at a new drop shaft (Shaft 3) located on the west side of the Black River, across from the city of Lorain Black River waste water treatment plant (BRWWTP). The tunnel will be dewatered at the south end by a large diameter pump station (Shaft 1) located in the existing Lorain Port Authority Public Boat Launch. Flow from the new pump station will be discharged into an existing shallow interceptor sewer and directed back to the BRWWTP."

Jan 1, 2014

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By Seth C. Scharfer

"As part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology, the Gibbs energies of formation of MoS2 (molybdenite) and WS2 (tungsten disulfide) were determined with high-temperature galvanic cells employing stabilized Zr02 (zirconia) as the electro¬lyte. In the temperature range from 867 to 1,209 K, potential measurements were obtained for the cellPt, MoS2 , Mo02 , SO2 = 1 atm // Zr02 // 02 = 0.0112 atm, Pt, with the overall cell reactionMoS2(c) + 3 02(g, 0.0112 atm) = Mo02 (c) + 2 S02(g). (1)These results, combined with the best available values for Gibbs energies of formation (?G°f) of Mo02 (molybdenum dioxide) and SO2 (sulfur dioxide) from the literature, give the standard Gibbs energy of formation of MoS2, ?G°f, for the reactionMo(c) + S2(g) = MoS2(c) (2)?G°f = -96.681 + 43.76 x 10-3T±0.538 kcal/mole, (3)where temperature (T) is expressed in Kelvins.Similar measurements in the temperature range from 872 to 1,210 K were obtained for the cellPt, WS2 , W03 , SO2 = 1 atm // Zr02 // 02 = 0.0114 atm, Pt, with the overall cell reactionWS2(c) + 3.5 02(g, 0.0114 atm) = W03 (c)+ 2 S02(g). (4) Combination of these results with the best available data of ?G°f for W03 (tungsten trioxide) and SO2 from the literature gives the Gibbs energy of formation of WS2 in the temperature range from 872 to 1,210 K for the reactionW(c) + S2(g) = WS2 (c)(5)?G°f = -92.429 + 43.88 x 10-3T ± 0.280 kcal/mole. (6)A third-law analysis yields a standard enthalpy (?H°f) for the reaction298Mo(c) + 2 S(rh) = MoS2(c), (7)?H°f = -67.36±0.60 kcal/mole, (8)298where the standard states are pure crystalline MoS2 / and rhombic sulfur."

Jan 1, 1980

By W. R. McDonald

Part of the U.S. Bureau of Mines mission is to supply the U.S. mineral industries with information that is useful in planning to meet the Nation's critical and strategic mineral needs if a national emergency occurs. The Bureau conducted laboratory research including operating a nominal 100 lblh pilot plant to demonstrate the recovery and concentration of chromite by gravity and flotation operations from three northern California mineral deposits. Gravity beneficiation test results show that concentrates contained as much as 52 pet chromic oxide (CrZ03) with recoveries of about 80 pet. Results from the bench-scale unit operations of mineral liberation, tabling, vanning, spiraling, pinch sluice, work index, and thickener area determination tests are presented in this report.

Jan 1, 1990

By A Minchinton

With blasting, all far-field phenomena including, but not limited to, stress wave propagation, fracture, vibration and muck pile formation are intrinsically and irrevocably dependent upon near-field phenomena or mechanisms that we describe using physics-based mathematics typically transcribed into computer codes. The energetics involved in such near- to far-field transitions are not fundamentally relevant as they are simply progenitors of these processes.The notion of explosive energy as a descriptor for explosive or blasting performance is a case in point. These energies, which are generally used in blasting tables, are almost exclusively based on ideal detonation theory alone and do not include the influence of the rock, charge diameter, blasthole length and the late-time dynamic expansion that can be predicted using codes based on non-ideal detonation theory.With decoupled charges in presplits for example, the pressure drop between the charge and the blasthole wall can be simply described to first order using the energy relationship associated with adiabatic expansion. However, a more realistic mechanistic solution involves interacting fluids and turbulence leading to dynamic processes such as the channel effect.CITATION:Minchinton, A, 2015. On the influence of fundamental detonics on blasting practice, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 41–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Antonio Nieto, Jesus Castillo

Research and Development (R&D) departments in the mining sector are essential for creating new solutions on productivity, safety, and sustainability. Nevertheless, the selection of R&D projects is complex, often influenced by subjective judgments and uncertainties. This paper explores the application of the Multicriteria Decision Analysis (MCDA) as a structured approach to evaluate and prioritize innovation projects based on various criteria such as safety, cost, environmental impact, and social acceptability. By assigning weights and quantifying criteria, MCDA enhances decision-making transparency and objectivity. This study aims to show a method that facilitates strategic thinking, resource optimization, and stakeholder engagement, ensuring that selected innovations align with the company’s long-term objectives and commitment to responsible mining practices.

Feb 1, 2025

By R. C. A. Thurston

AT A FATIGUE SESSION organised by the A.S.T.M. in 1949, R. E. Peterson presented a brief introductory paper ( 1) in which lie referred to a discussion on the fatigue of metals which took place in England in 1849, and then proceeded to review some of the subsequent researches concerning the mechanism of fatigue. In the course of the review, he discussed metallograpl1ic studies with single crystals and polycrystalline materials, studies with X-ray methods, and the application of the electron microscope. During that hundred-year period considerable progress was made toward a better under-standing of the nature of fatigue, although it is probable that even greater attention was directed to the more practical aspects of the problem, such as the effects of notches, temperature, corrosion, surface treatment, residual stresses, and so on. Since then there has been an appreciable acceleration in the tempo of the fundamental work, partly influenced by the rapid development of the theory of dislocations, with the result that our knowledge of the mechanism of slip, the initiation of fatigue cracks, and their subsequent propagation, has still further advanced, although it is by no means complete as yet. The present paper is an attempt to out-line the more recent developments in these basic studies, to correlate them when possible, and to draw attention to those directions in which research might profitably be pursued.

Jan 1, 1957

By Carlos Torres, Albert Cabrejo

For the last 20 years mine slopes have been monitored with slope stability radars. Since 2015 a group of dedicated geotechnical engineers dedicated to remotely monitor radars around the world have detected 2000+ slope failures of different characteristics. A statistical analysis of the information gathered of these failures have been made and the summarized results are presented with some degree of analysis appropriate for the vastness of the database. The analysis considers different types of commodities, countries, mining processes, rock types, and weather conditions.

Sep 29, 2023

By D. E. Shanks

As part of its goal to help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is investigating a fused-salt electrolytic procedure for producing zinc metal. A previous report described preliminary, small-scale work on the fused-salt electrolysis of ZnC12. The present report covers a more detailed investigation of the properties of ZnC12-alkali metal chloride electrolyte systems in relation to the production of zinc metal and also discusses electrolysis in largescale, internally heated cells. The effect of composition on bath stability, current efficiency, cell voltage, and liquidus temperature was determined for the ZnCla-NaC1-KC1, ZnC12-NaC1-LiC1, and ZnC12-KC1-LiC1 electrolyte systems. An electrolyte com-posed of 38 mole-pct ZnC12, 31 mole-pct NaC1, and 31 mole-pct KC1 gave the best overall results. Sludge (ZnO) formation in the ZnC12-NaC1-KC1, ZnC12-KC1-LiC1, and ZnC12-KC1 systems was investigated during prolonged electrolysis. The ZnC12-KC1-NaC1 electrolyte showed the least sludge formation. A 1,500-amp cell was operated using the ZnC12-NaC1-KC1 electrolyte at 500° C. Zinc metal was produced at the rate of 4.0 lb/hr with a current efficiency of 95 pct.

Jan 1, 1979

By E. R. MARBLE

THE introduction of a new fuel, such as natural gas, necessitates careful study where it has not been used previously. At the El Paso smelter natural gas required the installation of apparatus with which no one at the plant was familiar, either as to the type of equipment needed or as to the burning of the gas in it. Observation of existing installations of a similar character and assistance from gas engineers served as a basis to determine what was advisable to use. The gas line entering the plant goes to a metering station equipped with a duplicate system of pressure regulators, a temperature recorder and the gas company and smelter orifice meters in tandem. There are three distribution lines that can be inter-connected at a later date, if necessary, to assist in equalizing the plant load. All the larger lines are of heavy

Jan 1, 1930