Search Documents

By Lu Lin, Yan-ping Bao, Min Wang

In order to forecast the cost of dephosphorization during BOF process, and achieve economical dephosphorization of BOF. The mathematical model of dephosphorization cost for BOF process was established. The model calculations show that, when the silicon content and phosphorus content are increased in hot metal, and the final phosphorus content of BOF is decreased, the dephosphorization cost will be increased. The silicon content of hot metal is increased of 0.1% in the plant, the dephosphorization cost is added by 9 RMB/ton steel. The De-P cost of mode A is much higher than the other two modes for three typical production modes of single slag melting process, when the phosphorus content of hot metal is higher than 0.14%, an increase in the phosphorus content by 0.01%, the De-P cost of mode A is added by about 7 RMB/ton steel. Meanwhile, when the phosphorus content of hot metal is lower than 0.165%, the De-P cost of mode C is higher than mode B’s. For BOF single slag melting process, the dephosphorization cost calculated by model is between ± 2%, proving that the model is reliable for the prediction of dephosphorization cost.

Jan 1, 2015

Flotation Performance Improvement by Air Recovery Optimisation on Roughers and Scavengers

Sep 13, 2010

The negative effects of pyrite and pyrrhotite on thiosulfate gold leaching have been investigated. Possible remedies to reduce some problems are discussed. In a gold bearing pure silicate ore, 92% of gold could be extracted within 3 hours using a solution containing 0.2 mol/L ammonium thiosulfate, 0.9 mol/L ammonia, 30 - 300 ppm copper sulfate and 8.6 ppm dissolved oxygen at pH 10.26. The thiosulfate consumption was 7.1 kg/t under these conditions and could be further reduced to 3.5 kg/t by decreasing the dissolved oxygen to 0.3 ppm. Addition of 16% pyrrhotite or pyrite into the silicate slurry led to a decrease in gold extraction by 2% or 9% respectively and an increase of thiosulfate consumption by 11 kg/t or12.8 kg/t respectively in three hours. Several adjustments, such as increasing copper ion and ammonia concentration and reducing the dissolved oxygen level to 0.3 ppm resulted in increased gold extraction and lower thiosulfate consumption despite the presence of these sulfides.

Jan 1, 2005

By Oliver Bowles

Since 1922 when the Bureau of Mines issued a report2 covering the slate industry in detail, changes in technology have taken place which have an important bearing on the industry. The present paper comprises a record of these changes. Though the value of slate, for roofing, structural, blackboard, sanitary, and electrical uses is generally recognized, it has many competitors. To meet this constantly increasing competition producers are promoting economies in manufacture, and improving processes, thereby lessening costs of production, and are placing on the market products of the highest possible quality, thus creating satisfaction and confidence on the part of the user. This endeavor to place the industry on a better basis, both as regards processes and products, is shown in the recent developments in technology which are presented herein. Valuable assistance in obtaining data for this paper was given by W. S. Hays, secretary of the National Slate Association, N. M. Male, president of the National Slate Association, and Robert Notvest, consulting engineer, Cleveland, O.

Jan 1, 1926

By Javad Sattarvand, Milad Ghahramanieisalou

As new technologies are introduced to the mining industry, the challenges related to their safe assimilation and the potential changes they bring to mining techniques necessitate adjustments to the current operations. Predictive simulations are critical to understanding unforeseen scenarios and shifting costly changes from the operational stage to the design. The Digital Twin methodology has gained a lot of attention in recent years. Many industries, from manufacturing to engineering and even social sciences, are adopting this approach to understand better the complex systems they are working with. By considering the enormous expenses and risks related to a pilot project, DT could replace that by acting as a prototype in which realistic tests and simulations are carried out with close to zero cost. DT includes a data hub, simulation and analysis tools, and visualization platforms to enable appropriate designs and monitoring plans focusing on unknown areas. A few examples of DT's application in mining include fleet management, Mine-to-Mill optimization (especially D&B), geotechnical digital twin (gDT), etc. When developing regulations, testing the efficiency of the mine layout, design, and magnitude of the restricted area and its access points, human-machine interactions, risk identification, and management processes, examining the efficacy of control systems, and monitoring, DT could help speed up (or completely replace) the process in the physical world.

Jun 25, 2023

By A. Mainza, H. Hill, L. S. Bbosa

"Impact breakage is the most elementary size reduction mechanism in comminution devices. In comminution research, characterization of breakage is primarily concerned with the energy expended to cause it. The main challenges of this approach have been quantifying the actual energy requirements of impact breakage and developing mechanistic models to accurately describe the process. For engineering load analysis, fracture is characterized in terms of strengths such as yield stress and ultimate tensile stress, which govern the maximum loads specific materials can be subjected to before irreversible inelastic deformation and subsequently complete fracture occur. With this approach, the main challenge has been to elucidate the underlying mechanism, in the means that the load causes weaknesses in the material microstructure to act as sites for stress concentrations, leading to crack initiation, propagation and eventual failure. Studies dedicated to investigating particle fracture under impact loading have led to the development of several devices for conducting breakage characterization tests. These devices include the drop weight tester, split Hopkinson pressure bar, rotary breakage tester and the short impact load cell. All these have different particle loading and breakage methods, and thus can yield distinct information which can be compiled together to study a material and the nature of breakage. This work analyses the single impact breakage data obtained across the listed devices. A homogenous ore commonly known as blue stone is used for all breakage tests. The work is conducted using standard procedures specific to each device as closely as possible. Drop weight and rotary breakage tests were used to obtain hardness parameters based on an existing t10 breakage model, while split Hopkinson pressure bar and short impact load cell measurements provided properties based on conventional engineering load analysis. The results were used to highlight the significance of the loading geometry, impact mechanism and impulse on the extent of breakage."

Jan 1, 2018

By C. P. Manning

This paper reports recent progress in the development of a unique metal extraction technology utilizing zirconia-based inert anodes for the electrolytic reduction of metals from their oxides. In this process, the target metal oxide is dissolved in an ionically conducting liquid solvent phase. An extended anode consisting of an oxygen-ion-conducting stabilized zirconia membrane in intimate contact with a catalytically active electronic phase and an inert electronically conducting cathode are inserted into the molten flux containing the oxide. When the appropriate electric potential is applied between the electrodes the target metal is reduced at the cathode and oxygen ions are selectively transported across the stabilized zirconia membrane and oxidized at the anode. When the process is conducted at temperatures between 1200-1400°C, the ohmic resistance drop across the stabilized zirconia membrane is low, and high current densities on the order of I A/cm2 or greater can be obtained. In addition, the process efficiency can be increased further by directly reforming hydrocarbon fuel over the anode. Laboratory experiments at Boston University have demonstrated the technical viability of employing zirconia-based inert anodes for environmentally sound production of metals such as magnesium, tantalum, aluminum, etc., directly from their oxides. Significant progress has been made in the application of this concept to the electrolytic reduction of magnesium at 1300°C. The research topics covered include stability of the zirconia membrane in the selected molten solvent (flux), volatility of the flux, electrochemical characterization of the electrolytic cell, and analysis of the metals produced.

Jan 1, 2003

By P. N. Anyalebechi

Keywords: Aluminum alloy 3004, Solidification rate, Homogenization, Second phase particles The effects of the fineness of as-solidified cast microstructure and temperature on the response of aluminum alloy 3004 to homogenization heat treatment (a.k.a. preheat) have been investigated. The study was conducted at 538oC and 595oC on directionally solidified laboratory-size ingots with a range of solidification rate of 0.10oC/s to 29.4oC/s. Optical and electron microscopy, quantitative image analysis, electrical conductivity, and electron probe microanalysis were used to quantify the effects of the homogenization heat treatment on the microstructure of aluminum alloy 3004. In general, increase in fineness of as-cast microstructure and homogenization temperature enhances the a-transformation reaction, dissolution of Mg2Si, elimination of dendritic microsegregation, and dispersoid formation. The homogenization heat treatment reduces the average size of second phase particles in castings solidified at <1oC/s. However, in castings solidified at above 1oC /s, homogenization causes the coarsening of the second phase particles. Mn in solid solution is independent of homogenization heat treatment temperature.

Jan 1, 2005

By Toshihiko Emi

The quest for cleaner steel is driven by increasingly stringent requirements from the manufacturing and construction industries. Key issues are the occurrence and removal of inclusions; These are discussed in the context of the unit processes of deoxidation, refining, transfer and casting of molten steel. Process thermodynamics and kinetics are also discussed. Recent progresses achieved and problems yet to be solved are elaborated, and an integration of the unit processes into a system to produce extra clean, steels with better performance is presented.

Jan 1, 1999

By Wesley T. Holmes II, Lloyd H. Banning

Electric - smelting studies were made on titaniferous materials obtained from the Klukwan and Snettisham , Alaska ; Choteau , Mont .; and Iron Mountain , Wyo . , deposits with the objective of determining the feasibility of producing pig iron and an enriched titania slag in one test series and pig iron alone in another test series . In addition , related studies were conducted to determine the amenability of Choteau crude ore to wet -magnetic separation and to determine the quality of steel that could be produced from the titaniferous pig iron . The continuous smelting tests were made in a three - phase , submerged - arc , electric furnace , and the laboratory steelmaking tests were made in a singlephase electric - arc furnace . A continuous , belt - type , wet - magnetic separator was used in conjunction with a ball mill and a spiral classifier in recovering titaniferous magnetite from the crude Choteau ore . Pig irons containing less than 0.05 percent phosphorus or sulfur were readily produced from the titaniferous materials ; iron recoveries ranged from 92 to 98 percent . The Choteau ore was ground to minus 65 - mesh to produce a concentrate containing 60 percent or more iron . The steel produced from the titaniferous pig iron was a high - quality product .

Jan 1, 1964

CHARLES E. GUILLAUME,* .Sèvres, France written discussion?).-Referring top. 2052, experiments made at the end of the year 1884showed a remarkable agreement between the indications of various verre dur thermometers of which all the corrections had been determined with the greatest possible precision. The maximum deviations not attributable to the comparisons themselves were then about 0.002 to 0.003 degree. Much later, greater differences began to show. They were caused by the fact that the glassmaker-had modified the composition by adding to it a small quantity of lead. Efforts are now being made in France to obtain a regular, supply of glass made according to the old formula. The determination of the boiling point of sulfur made by Chappuis,1 444.5°, accords very well with the value noted on p. 2054. The International Committee of Weights and Measures and the General Conference have already considered the future abandonment of the hydrogen scale in favor of the thermodynamic scale. The hydro-gen scale appears to be, in their estimation, a transitory one, happily so closely approaching the final scale that no correction should be necessary for all measurements of temperature made during the last 30 years.

Jan 12, 1919

By D. B. Gawthrop, A. Taylor, G. St. J. Ferrott

"This paper presents data obtained as part of an investigation of the explosive properties of ammonium nitrate. During the course of the work: it was found desirable to investigate the sensitizing action of nitrostarch in mixtures of ammonium nitrate containing low percentages of this material. Data were derived as to the sensitivity to decomposition by heat and the completeness of detonation and,of detonation of straight ammonium nitrate, as compared with ammonium nitrate-nitrostrarch mixtures containing 1 to 10 per cent of nitrostarch.The ammonium nitrate was a sample of coated material obtained from the salvage of amatol shells. Its analysis was as follows:"

Feb 1, 1930

By R. J. Wasilewski

Elastic constants have been determined on single crystals of maximum-melting-temperature NiAl compound (50.6 at. pct Al) at 25°C. Temperature variations of Young&apos;s modulus in the three principal crystal directions between -150°C and +800°C exhibit no anomalies similar to those repovted for the isomor-phous compounds brass and AuCd. It is concluded that the ordered CsCl structure is stable throughout the temperuture range investigated NICKEL aluminide is a congruently melting inter-metallic compound of CsCl (B2) structure, stable over a rather wide composition range (40 to 54 pct Al). It exhibits a lattice-parameter maximum of a. = 2.883A at 50.6 pct 1,&apos; at which composition the excess aluminum atoms are randomly distributed on the vacant nickel sites;&apos; at higher nickel compositions the excess nickel atoms replace substitutionally in aluminum sites, while at higher aluminum compositions vacancies are present in the nickel sublattice.&apos; For compositions close to NiAl no significant variation in order has been observed at temperatures up to 900°C.3 At high nickel (65 pct) compositions the existence of a martensitic structural transformation has been reported.4 NiAl is isomorphous with the ordered B-brass structure and with the high-temperature structures of AuCd and TiNi alloys close to equiatomic composition. All of these exhibit anomalous elastic behavior as the temperature of their diffusionless transformation to lower-symmetry structures is approached.&apos;-&apos; This behavior has been explained as indicative of low stability of the CsCl structure in these compounds.8 The present paper reports the experimental determination of the elastic compliances of single-crystal NiA1. EXPERIMENTAL METHOD 1) Specimens. Polycrystalline NiAl was prepared by induction melting of carbonyl nickel and high-purity aluminum and casting into solid copper molds in gettered helium atmosphere. The castings thus produced were canned in mild steel and impact-extruded at 1100 to 1200°C to 38-in.diam rod. After the steel sheath was pickled off, the rods were converted to single crystals by repeated high-frequency satisfactorily produced the desired orientations in the form of crystals 38 in. diam by 8-12 in. long. These were subsequently center less-ground to 7 to 8 mm diam by 12 cm long, electropolished (in 80 pct methanol, 20 pct HzSO, at 25°C and 15 v), and their axial orientation determined to 1 deg by the Laue back-reflection technique. The rod dimensions were determined to 0.01 mm and the densities determined from geometrical dimensions and the weight of every specimen. The average density was 5.905 0.005 g per cu cm. 2) Elastic Data Measurements. Room-temperature elastic compliances Sii were obtained by determining to 0.1 cps the fundameGtal resonance frequencies in the longitudinal and torsional vibration modes. At these frequencies the following relations hold: E =p(2lfif =pvl= Sn- 2r[Sll- S12- -£„«] g -P(2iftf = pvf = (s<« - fr(sii - sw - ±s»y where vl and vt are the velocities, and f andft the resonance frequencies of the longitudinal and torsional waves, respectively; 1 is the length of the specimen, and r is the direction cosine factor—{cos2 a • cos2 0 + cos2 a . cos2 y + cos2 0 ¦ cos2 Y}. Given three crystals of orientations (loo), (110), and (111)) i.e., F = 0, 14, and 13, we can obtain six equations for the three unknown compliances, thus providing adequate internal check. Mode mixing can readily occur in the relatively long wavelength resonance utilized here. This could cause a significant error in the torsion wave velocities calculated from the apparent resonance frequenies. Therefore, throughout the present work, a method, described previosl,&apos; was used to ensure that no significant mode mixing took place at resonance. The apparatus used was originally designed for the Elastomat, Magnaflux Corp.. Chicago, 111. determination of flexural vibration resonance frequencies. At room temperature torsional vibration mode could be established by suitable positioning of the thin wires from the input and pick-up transducers, and longitudinal mode by cementing thin magnetic foils at the ends of the specimen, and inducing the vibration by means of electromagnetic transducers. Only flex-ural resonance frequencies could, however, be obtained reproducibly over the temperature range of -150 to 800°C. These data are considerably less accurate, the error in the modulus being estimated at -0.6 pct from the specimen dimensions and the room-temperature Poisson&apos;s ratio. The reproducibility of the resonance frequencies in repeat runs was, however, to better than l in 15,000, hence the relative elastic modulus error less than 0.02 pct. Therefore, the temperature variation of the principal Young&apos;s moduli obtained by flexural resonance, relative to room-temperature values, is believed to be satisfactorily accurate.

Jan 1, 1967

By Arnold B. Hubbard

A thermal decomposition study of the kerogen in three Colorado oil shales was made at different temperatures by heating the shales in the absence of oxygen at atmospheric pressure and measuring the decomposition products (gas, oil, and bitumen) formed. From these data the specific reaction rates, "k", for the thermal decomposition of kerogen were determined for each temperature studied, making it possible to calculate the time required to accomplish a given amount of decomposition within the temperature range. The influence of temperature on reaction rates was presented by plotting the data according to the Arrhenius equation, thus providing a means of estimating the values of "k" for any temperature within the range of this study. It was found that the specific reaction rates for the thermal decomposition of the kerogen in the three sampler were comparatively equal at corresponding temperatures.

Jan 1, 1950

By Ashley Tews

In 2005, we automated a forklift-based Hot Metal Carrier to be capable of typical metal transfer operations around a smelter. The project was highly successful and the vehicle has demonstrated hundreds of hours of live autonomous operations to thousands of people from industry and the public. As a result of the exposure and success of the project, we have expanded its focus to demonstrate how various technology components can be utilised to gain benefits in other areas of industrial operations. These include asset tracking, vehicle usage analysis, pedestrian detection and infrastructure profiling. Each of these components was derived from the core autonomous vehicle technology suite and has shown a high potential for improving safety and efficiency of vehicle-related operations, and improved diagnostic processes for measuring deformations of bakes and furnaces. The autonomous vehicle project and its extended technologies are described in this paper.

Aug 1, 2013

By B. McFadzean, S. Pikinini, C. T. O’ Connor

Sperrylite (PtAs₂) comprises about 21% of the platinum group minerals (PGMs) in the Platreef ore and regularly reports to the tailings due to its poor floatability. Hence, improving its recovery will be of great economic value to the South African PGM industry. The reasons for its poor floatability are not yet clear. This paper seeks to understand the interactions occurring between PtAs₂ and common thiol collectors, viz. potassium normal butyl xanthate (PNBX), sodium normal dibutyl dithiophosphate (SNBDTP) and sodium normal mono butyl dithiocarbamate (SNBDTC). By understanding its interactions with these collectors, it is hypothesised that it will be possible to suggest ligands that may help improve the floatability of sperrylite. Mineral-collector interactions were studied by determining the molar energy of interaction using isothermal titration calorimetry and electrochemical techniques. The hydrophobicity of the mineral before and after adsorption of the collectors was determined by heat of immersion and its flotation response determined by microflotation tests. Microflotation tests using synthetic sperrylite at pH 9 showed low collectorless recovery of 34.8% and after adding the equivalent of one pseudo-monolayer of the PNBX collector, the recovery of 32.5% was obtained. Moreover, the addition of up to three pseudo-monolayers coverage of PNBX did not result in any increase in flotation recovery. A small recovery improvement was noted when synthetic plant water with the ionic strength of 0.0484 mol/L was used, but this did not hold for all collectors, with SNBDTP exhibiting higher recoveries in distilled water. Keywords: Sperrylite; flotation; recovery; adsorption energy; collectors; 2SPW (synthetic plant water)

Jan 1, 2020

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018

By Brian Isherwood, Tara Brown, Paul Kreycir, Jenny Earle

"The Shangri-La hotel and luxury condominium tower, recently opened on University Avenue in downtown Toronto, required eight levels of underground structure, four extending into the shale bedrock.Isherwood Geostructural Engineers was retained in 2007 by Anchor Shoring Limited to provide an alternative design-build solution to better address serious foundation risks. The site, bounded on three sides by City streets, abuts an existing 1957 14-storey building with five underground levels to the north. Sitting on the rock surface along the east perimeter under University Avenue runs the existing Toronto Transit Commission’s University Subway Line built by cut-and-cover in the 1950’s and which was believed to lie very near the property boundary at the southeast corner of the site.The bedrock under Toronto is known to contain very high locked-in horizontal stresses, much higher than can be resisted by shoring techniques, which result in inevitable wall movement when excavating deep into the rock. The strategy adopted to control the risk to the Subway, adjacent building, and major utilities is described in the paper, along with the comprehensive monitoring of movements, and their comparison to predictions.The ProjectThe 66-storey Shangri-La hotel and luxury condominium tower, recently constructed on University Avenue in downtown Toronto, houses 222 hotel rooms in floors 1-17; 287 residences on floors 18-49; and private estates including two 2-storey penthouses on floors 50-66. These comprise 873,000 square feet of development. Eight levels of underground basement are required to provide parking and other amenities, the lower four extending into the shale bedrock."

Jan 1, 2015

By Frederick Bloetscher

An improved parachute-type stopping for changing the course of mine ventilation air during mine emergencies has been developed by Goodyear Aerospace Corporation for The Bureau of Mines. The stopping can be quickly deployed by one man from a single attachment point and provides excellent stopping performance with the flow in the design direction. Adding pin and foam attachments between its skirt and the passage-way surfaces improves its performance with flow in the design direction and maintains the stopping with zero or reverse air flows. Stopping performance results for a range of airway sizes including 7.5 X 10 ft simulated airway with pressure differentials of up to 3.0 inches of water are presented. Predicted performance values for this stopping design for larger passageways are also presented.

Jan 1, 1977

By M. Hesham El Naggar, Yasser Abdelghany

"ABSTRACT: The axial and lateral monotonic and cyclic behavior of helical pile foundations was investigated and new innovative helical screw systems suitable for seismic loadings were developed and patented. More than one hundred full scale field load tests were conducted on instrumented helical screw piles installed in cohesive soil. The piles included: plain helical screw piles (P-HSP); grouted (G-HSPs); fiber reinforced polymer FRP-G-HSPs; and reinforced grouted RG-HSPs. The RG-HSP piles axial capacity was more than twice that for P-HSP, with minimal reduction after cyclic loading, and their lateral capacity was more than 3 times the P-HSPs capacity. A 3-D finite element model was established. The results of 3-D finite element modeling were used to establish the load transfer mechanism and a design methodology for the considered piles.INTRODUCTION AND LITERATURE REVIEWHelical (screw) anchors have been utilized in tension loading and have gained popularity for bearing load applications. Helical piles represent an overall cost effective alternative to conventional piles for new construction and repair applications. The helical piles speed and ease of installation, less noise during installation added advantage with regards to their efficiency and reliability for underpinning including re-support and reconstruction of distressed and damaged foundations for either stabilization or rehabilitation. The “square shaft” SS175 pile is a segmented deep foundation system with helical steel bearing plates (helices) welded to a central steel shaft. Load is transferred from the shaft to the surrounding soil through these bearing plates. Segments or sections are joined with bolted couplings. Practically installed depth is limited only by soil resistance and economics. A helical bearing plate or helix is one pitch of a screw thread. All helices regardless of their diameter have a standard 75 mm pitch (Figure.1). The performance of single helical anchors and group action were studied experimentally and theoretically by several researchers, the researches focuses on the installation torque and uplift resistance. Some researches focus on the load carrying capacity with little pile response to cyclic loading effects or to instrumented full scale field testing. Helical piles axial compressive or lateral loading still is not well characterized and needs more analyses and their seismic performance was not investigated. For such this research was initiated to investigate the helical piles monotonic and cyclic performances under axial and lateral loadings to consider their usage in different applications in seismic zones. Among the several researchers, Clemence (1983); Mooney et al. (1985) conducted field and laboratory testing; Hoyt (1989), Hoyt et al. (1995), and Ghaly and Clemence (1998) conducted theoretical and experimental testing, Puri and Vijay (1984), Huang et al. (1995), Perko (2000), and Pack (2000) conducted theoretical analyses. Rao and Prasad (1993), Prasad and Rao (1994), conducted experimental testing; Vickars and Clemence (2000) studied the performance of helical piles with grouted shafts."

Jan 1, 2014