Search Documents

By Emil H. Geus

A process has been developed to recover aluminum from dross which does not require the use of salt flux as commonly employed, This results in a salt-free residue which has potential industrial uses or alternatively can be safely land-filled. The dross is first heated by an air-fuel or oxy-fuel burner in a sealable rotary furnace. At a suitable temperature the burner is turned off and the temperature of the dross thereafter controlled by means of an atmosphere of oxidative and inert gases. When the free metal has agglomerated it is first discharged from the furnace, followed by the residues.

Jan 1, 1995

By D. L. H. Bulbring

The removal of a cylindrical core from thick-wall sections for creep analysis by the relatively new Weldcore® process represents a very exciting methodology for obtaining more representative creep damage data from large engineering structures. The cylindrical core that is removed, representing about 60% of the wall thickness, leaves a substantial removal site that needs to be repaired. This paper presents data pertaining to taper Friction Hydro Pillar Processing as an alternative repair technique for filling the core removal site. Process parameters were evaluated with special attention being paid to the effect of downward force on process response variables, weld defects, and mechanical properties of 10CrMo910 steel. Process temperature and torque response as well as total process energy input were also considered. This paper also assesses the static and dynamic performance of this repair technique. The influence of a varying downward force and the occurrence and position of discontinuities were quantified. Downward force was shown to have the most notable effect on weld joint dynamic performance and was found to be related to the process temperatures achieved in close proximity to the weld interface.

Jan 1, 2013

By T. S. Golosinski

This paper identifies the components of belt conveyor shifting force as a vertical force. Pv, horizontal force, Ph, and longitudinal force, P1. A method for estimation of these forces is proposed, which relates their value to the properties of the conveyor structure and rails, shifting operation parameters, and other site-specific conditions. The effect of this force on shifter behaviour is analysed and guidelines are developed for selection of a suitable shifter. Also discussed are the requirements of the shifting operation for other equipment.

Jan 1, 1986

By J. J. Moore

The application of plasma technology to process metallurgy is briefly discussed. Experiments involving in-flight reduction of minerals (taconite, chromite, in particular) with a solid-based carbon reductant are described. The resultant metallic and slag product analysis is discussed with respect to thermodynamic and kinetic considerations.

Jan 1, 1985

Miners and explorers in New Zealand are expected to consult with stakeholders, keep out of core conservation areas, and operate a high standard of environmental management and rehabilitation. These requirements are not difficult to meet, but many of the industry's own actions have brought it to a low level of general public esteem in New Zealand. Reasons for this are discussed, drawing examples from the Maruia Society's experiences with the industry since the mid-1980s. The boundary between core conservation areas and other land is not easily drawn, and the Maruia Society has sought to work with the mining industry to promote legislation for net conservation benefit trade-offs. However this initiative was not successful. Today the industry, unlike most other major industry sectors in New Zealand, has no accord with the country's conservation movement.

Jan 1, 1997

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the SrF2-Y2O3 system for which liquidus and solidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. The phase diagram was constructed from information obtained by ceramogra¬phy, X-ray diffraction, thermal analysis, and electron probe microanalysis of small specimens encapsulated in platinum-20 percent rhodium or molybdenum ampoules. The data indicate a simple eutectic system with limited terminal solid solubilities. The eutectic temperature is 1,457°±5° C, and the eutectic composition is 4±1 mole-pct Y203. Strontium fluoride containing up to 2 wt-pct 0 2 was studied to determine the effects of oxygen contamination. Oxygen levels in excess of 0.2 wt-pct resulted in eutectic formation between SrF2 and SrO. The eutectic composition is between 0.2 and 0.7 wt-pct 02, and the eutectic temperature is 1,447°±5° C. No intermediate oxyfluoride phases were detected.

Jan 1, 1974

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Colorado School of MinesResearchers at Colorado School of Mines (CSM) have developed computational fluid dynamic (CFD) models to study gas distributions and explosion and fire hazards in longwall gobs. In underground coal mines, methane continuously emitted from surrounding strata mixes with air from active mine workings and may form explosive gas zones (EGZs). Some western United States coal mines are also prone to spontaneous combustion (spon com). Insight into oxygen concentrations within the gob is crucial for assessing spon com hazards and mitigation strategies. Nitrogen injection used in conjunction with progressive gob sealing can reduce EGZs and spon com hazards by forming a dynamic seal that separates the methane in the gob from the air that ingresses from the face. This paper describes CFD modeling simulations studying the formation of such dynamic seals by optimizing the nitrogen injection locations. The impact of nitrogen on oxygen ingress and formation of EGZs is discussed. Optimum nitrogen injection quantities and injection locations were determined. Dynamic seal formation is most effective if the headgate nitrogen injection locations are split between the first crosscut inby the face and a second location about 300 m (1,000 ft) further inby. INTRODUCTION Underground longwall coal mine ventilation systems are designed to dilute hazardous gases and to provide breathable air to miners working in the area. Methane gas is liberated as the mining process extracts the coal and disturbs the surrounding strata. Methane mixes with the ventilation air and often produces explosive gas zones (EGZs) within longwall gobs (Brune 2013). Past CFD modeling research of underground coal mine ventilation systems has shown the effects of face air quantity on EGZs (Worrall 2012) and nitrogen injection to control spon com (Balusu et al. 2005; Ren et al. 2012; Ren et al. 2011; Smith and Yuan, 2008; Yuan and Smith, 2014). Other modeling approaches include network ventilation models of oxygen ingress (Dziurzynski and Wasilewski, 2012), and coupled Linear Network CFD algorithms (Wedding 2014). In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), CSM researchers are using Fluent®, a CFD software package by ANSYS, Inc., to model gas compositions and flows in underground longwall gobs. Figure 1 shows a progressively sealed gob with a U-type ventilation system in a three entry development. As the longwall advances, seals are constructed along the headgate in the crosscuts between the center entry and the gob. Additional gob isolation seals are built to block off the headgate entries inby the face. Nitrogen is injected through the seals in the first two crosscuts on the headgate side and at the first crosscut inby the face on the tailgate side, as shown in Figure 1."

Jan 1, 2015

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation: "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest, air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers. etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables. FUGITIVE DUST Most state air pollution regulatory agencies now have rules and regulations requiring control of fugitive dust. This refers to dust generated from normal processing operations. A typical air pollution control agency regulation reads as follows: "Fugitive Dust" "No person shall cause, suffer, allow, or permit any material to be handled, transported, or stored; or a building, its appurtenances, or a road to be used, constructed, altered, repaired, or demolished without taking reasonable precautions to prevent particulate matter from becom-

Jan 1, 1973

By E. D. Gradner

During 1924 a number of lives were lost and other men incapacitated by the toxic effects of gases produced in blasting in massive sulphides. In one mine, three men working in a raise were caught by gases from blasting a drift round in massive sulphide on the level. The round in the drift was shot ahead of time and it was necessary for the three men to travel through the gases to the intake air course. Two of the men lost their lives, and the third was injured, apparently for life. Other men at this same mine have been caught in the gases at blasting time and seriously injured. At a second mine, the gases from blasting in sulphides appear to be very dangerous, and it was necessary to send a number of men who were caught in such gases to the hospital. One man who was seriously gassed has not recovered in over a year is time. Another man similarly gassed soon died of influenza.

Jan 1, 1926

By Richard E. Hucko

The Coal Preparation Division of the Pittsburgh Mining Technology Center conducted an investigation to assess and compare the pyritic sulfur reduction potential of coal-pyrite flotation and high-gradient magnetic separation (HGMS). Tests were run on three coals--an Upper Freeport bed coal, a Lower Kittanning bed coal, and a Pittsburgh bed coal--to establish grade- recovery relationships characteristic of both processes. Representative portions of each coal sample were crushed to two top sizes--nominal minus 35 mesh (0.5 mm) and nominal minus 100 mesh (0.149 mm)--and subjected to conventional froth flotation. The froth product was then beneficiated by coal-pyrite flotation or HCMS to provide a direct technical comparison of the two processes. At minus 35 mesh (0.5 mm), the size normally employed for coal flotation, both coal-pyrite flotation and HGMS effectively separated pyrite from coal, and the performance of the two processes was essentially the same. At a size of minus 100 mesh (0.149 mm) , however, the performance of HGMS exceeded that of coal- pyrite flotation. The separations effected by HGMS were more efficient at minus 100 mesh (0.149 mm) than at minus 35 mesh (0.5 mm). On the other hand, it was concluded that either the effectiveness of coal-pyrite flotation decreases with diminishing top size, or the process has not been optimized to treat material finer than 35 mesh (0.5 mm).

Jan 1, 1981

By M. D. G. Salamon

It has been noted in recent years that the pillars in some bord-and-pillar workings scale or spall. In due course this process may result in the collapse of the affected panels. This paper presents a methodology for assessing the long-term behaviour of such workings, employing a simple model of pillar deterioration by scaling. It is assumed that scaling causes a gradual reduction in pillar width, hence the safety factor of pillars reduces in time. It is also postulated that the process of scaling will be arrested if the coal rubble around the pillar reaches a critical height. The probability that the pillars will survive for a certain period of time, or indefinitely, can be estimated. This can be accomplished by using the log-normal distribution proposed by Salamon and Munro4todescribe the distribution of the apparent safety factor values at failure. If an estimate of the rate of scaling is known, it is also possible to quantify, using a Monte Carlo technique, the expected life of the pillars. The method also facilitates pillar design by specifying a probability of survival for a given number of years or, alternatively, for an indefinite period. Using the limited pool of available data, analyses show that the proposed model does not appear to be inconsistent with observed behaviour of pillars in the Vaal Basin. The crucial parameter is the rate of scaling. Back calculations from eleven cases suggest that the rate of spalling in the Vaal Basin is about 0.2 m/year. It is noteworthy that two further cases in the same area give significantly higher rates (0.85 m/year). Some underground observations in the Witbank area indicate considerably lower rates in the order of 0.02?0.04 m/year. Further areas for study are recommended. These include a study of old workings to determine the extent and rate of scaling in the various coal fields, an investigation into the possible relationship between scaling and the chemical composition of the coal. In addition, model studies will be required to assess the practical impact of the research findings.

Jan 1, 1998

The major components of sylvinite ores, sylvite (KCl) and halite (NaCl), are separated by flotation. Since both these minerals are water-soluble, the process is carried out in a saturated brine, 6~7 mol/L aqueous solution of NaCl and KCl. C16~C22 primary amines, utilized as a collector, are practically insoluble in water. In commercial potash ore flotation operations these amines are melted by heating up to 70~90°C. They are then neutralized with hydrochloric or acetic acids, and such a hot emulsion/dispersion is introduced to the flotation pulp (which is at room temperature). This is immediately accompanied by the appearance of a white precipitate in the system. As our measurements indicate, the Krafft point of dodecylammonium chloride in concentrated electrolyte solutions is much higher than 80°C, and the Krafft point of C16~C22 amines is substantially higher than that. Introduction of a hot amine emulsion into a pulp, at temperature much lower than the Krafft point for the utilized amines, must cause precipitation of the amines. Some of these species are obviously flotation-active. It is interesting to observe that in summertime, when temperatures are high-er, longer chain amines perform better. It demonstrates that the colloidal amine species that precipitate serve as active species in the potash flotation. Therefore, at higher pulp temperatures, when the temperature difference between the pulp temperature and the Krafft temperature of the utilized amine is not sufficiently large, a longer chain amine, the amine with a higher Krafft point, is more efficient. The results reveal that premixing of an alcohol such as MIBC (common frother) with the amine significantly improves flotation performance of the amine. In the presence of such an alcohol the amine disperse system becomes less turbid, and the rheology of the system less non-Newtonian. All this indicates that MIBC, which does not operate as a frother in a potash flotation system, when used as a co-surfactant, enhances the dispersion of the amine colloidal system. The appearing colloidal species perform as an active form of the collector.

Jan 1, 2014

By Yasuo Ojima

The mainstream of copper smelting processes in the world today is a combination of Outokumpu type Flash smelting and PS (Pierse Smith) converting process. Presently it can be estimated that about 50% of the worldwide copper production is produced by the Flash smelting process and 80% by the PS converting process. PS converting process due to its operational flexibility and despite its batch character of operation has been widely used in many smelters for more than 100 years. However, an environmental issue has been pointed out related to this process because of the difficulty of handling the fugitive gases. Recently several copper smelters in the world have been newly constructed and others have executed major modification and modernization, The continuous converting process has been applied in many of them instead of PS converting process. This paper compares PS to the emerging continuous converting process and makes a prospect of the future of the copper converting process.

Jan 1, 2003

By D. C. Torre

The need for a successful, efficient and reliable continuous face- haulage .system for use with continuous mining machines has been apparent since the first continuous miners were introduced some twenty-five years ago. Some thought and effort were given to the development of continuous haulage over the last twenty years or so. Some initial success was experienced in this area by The Long Company with a system involving bridge conveyors, as far back as the late 1950's. However, extensive success with continuous face haulage for use behind modern, high product¬ion, continuous miners escaped the industry until the early 1970's. It is true that continuous face haulage was successfully introduced into low seam mining, generally in seams ranging under 1.07 m (42") in height, in the 1960's, for use with relatively low production, low seam, auger type continuous miners. However, those available systems which have achieved success in the lower seams, where relatively low capacities are adequate, are not directly applicable for use with today's medium and high seam miners with their standard production capacity of 9.1 - 10.9 mtpm (10 - 12 tpm). Since the late 1960's and early 1970's, several machinery manufacturers, and at least two major coal companies, have devoted considerable expense, time and effort to developing truly successful continuous face haulage for use in coal seams ranging upward from 1.2 m (4') in height. Continuous face haulage equipment has been developed in the last five years employing a variety of transportation media and design concepts, including some which have received wide publicity such as those employing hydraulics, and pleated belt. The truth of the matter is, however, that the only universally applicable and widely successful continuous face haulage equipment introduced to date has been that employing a combination of bridge conveyors and mobile, self-propelled, bridge carriers, connected at the inby end to the tail of the high production continuous miner, and at the outby end attached directly to the panel conveyor (Fig. 1 & Fig. 2) or, on occasion, to a short, self-contained conveyor which, in turn, empties directly onto the panel conveyor. While these bridge type continuous haulage systems are available with both belt and chain conveyor components, the most widely applied and successful system in seams above 1.07 m (42") in height is that offered by The Long-Airdox Company. The standard unit for use with 9.1 - 10.9 mtpm (10 - 12 tpm) continuous miners is normally equipped with belt. However, they have built, and successfully applied, versions of this system employing chain conveyors, (Fig. 3), mainly for operators having extremely difficult mining conditions, including excessive amounts of water

Jan 1, 1977

By A. R. Hasankhoei

Water recycling is of prime importance in mineral processing due to consumption of large amount of water. This issue is vital in areas with a low rainfall such as Shahre-Babak (Kerman, Iran). Deep cone thickeners, unlike conventional thickeners, have a low diameter to height ratio where large amounts of flocculants are used to increase particles settling rates. The high bed heights (over 10 m) produce enough pressure to create a paste type underflow indicating maximum water recovery. Flocculent preparation, conditioning, and distribution along with the bed height are among the important factors affecting the performance. Four deep cones are used to recover water from the tailings of the plant. Plant data indicated that the thickener never reached the target underflow percent solids (63%) and the average underflow concentrations were between 49 and 57%. By modification and optimization of flocculent preparation and distribution methods the underflow percent solids increased by 3-4%. This translated to an increase of water recovery from 67 to 73%. This was equivalent of 53000 m3 saving in monthly water consumption. Keywords: deep cone thickener, water recovery, flocculant, copper tailings

Sep 1, 2012

By Joseph G. Wargo

The purpose of this paper is to investigate trends in exploration expenditures of a selected group of mining companies for the interval 1968 through 1971. The paper also compares these trends with other financial factors that are associated with various groups of companies and comments on the implications of these trends. Although a four-year interval is hardly enough time to establish a long-range set of trends from which operating rules can be derived, the fact that the four years selected are in the immediate past gives some sense of relevance to the matter of exploration expenditures at the present time and in the near future. The sample under study here consists of 21 mining companies. Of these, 19 are listed on the New York Stock Exchange and 2 are listed on the American Exchange. Twenty are American, one is Canadian. All are fundamentally "mining companies" in that they derive the bulk of their income from the extraction, sale, and at times, fabrication of metals from their own mines. This is in contrast to companies which have mineral exploration departments but derive the bulk of their revenues from sources other than mining; for example, from oil and gas sates, Also, no companies which can be considered strictly as exploration companies are included in this study. Although this definition held up fairly well when studying this list in 1968, the strict application of this definition became more difficult through the years up to the present time. In 1971, three or four of the companies were changing their character in that they were phasing out of the mining business, and either deriving their income or planning to derive a substantial part of their income from activities other than mining. A study of

Jan 1, 1973

By E. E. Maurer

Kerr-McGee has operated the Ambrosia Lake uranium mill since startup in 1958. Tonnage milled per day has varied from 3500-7000 tons. The mill capacity is currently rated at 7000 tons per day. The process consists of two parallel circuits following crushing and sampling, \\lhich include open circuit rod mill grinding, sulfuric acid leach, cyclone classification, and counter-current washing circuits of sand classifiers and slime thickeners. Pregnant solution is clarified and polished by precoat pressure leaf filters prior to amine solvent extraction. Yellowcake is precipitated from the pregnant strip solution with ammonia, filtered and dried.

Jan 1, 1972

By Yoshinori Kurumada, Masaya Watanabe, Kenji Sasa

"The Port of Yokohama is strengthening its international competitiveness as a strategic container port in order to respond appropriately to global exchange and shipping demands. Thus, the Minami Honmoku main Pier is currently being developed. The high-standard container terminals MC-1 and MC-2 have already started their service, and the development of the container terminals MC-3 and MC-4 is currently in progress.Because the South Honmoku Pier plays an important role in waste disposal management of Yokohama, a final waste disposal site (controlled final landfill site) is being developed in Block 5 to provide long-term and stable reception of waste that will be generated in the city. For this project, a revetment with water-blocking properties and an extension approximately 1.7 km in length is being built in order to prevent water from leaking from the disposal site. The base part of the revetment will be subjected to foundation improvement using the Cement Deep Mixing (CDM) method in order to secure water shielding of the soft sediment underneath the water, prevent slipping of the seawall, reduce the amount of subsidence, and increase the foundation support force.This report presents a preliminary study on using CDM on reclaimed soil and the construction process of the development project of the disposal site in Block 5 of the Minami Honmoku Pier, which has been underway since 2007.ABOUT MINAMI HONMOKU PIERThe development of the Minami Honmoku Pier started in 1990. It was designed to develop high-standard berths with greater water depths in order to handle the increasing volume of foreign container cargo and growing size of vessels. Figure 1 shows the layout of Minami Honmoku Pier. In April 2001, the Phase 1 (MC-1 and MC-2) began services. This is the newest pier in Port of Yokohama.This pier has one of Japan’s largest terminal areas (40 ha) and is equipped with 22 row-type mega gantry cranes capable of handling the newest ultralarge container ships. The pier has a quay with a water depth of 16 m, which is the first in Japan. The pier is equipped with advanced facilities and equipment to let Port of Yokohama be internationally competitive and function as an international commercial hub. An innovative system for high-efficiency transport is currently being introduced; it includes the installation of waiting vehicle lanes and a reservation-based loading and unloading system.Since the fiscal year 2007, a new container terminal (MC-3) with a -20m deep quay capable of handling the increased size of container ships and the diversification of port logistics has been under construction and is nearly completed."

Jan 1, 2015

By Fei-chiu Huang

The principle of time domain reflectometry (TDR) is being used by the U.S. Bureau of Mines to monitor strata displacements induced by mining. The Northwestern University TDR Signature Analysis (NVTSA) Program was developed under contract with the Bureau to allow for visual comparison of three TDR waveforms quickly and easily. This program is interactive, and on-line help is available. The Northwestern University Remote Control TDR Data Acquisition System and Modification of Tektronix SP232 Host Application Program (NUMOD) was then developed to allow acquisition of TDR wave-forms from a remote cable tester via modem. The NUMOD system utilizes commercially available software while the NUTSA program is available from the Bureau. This report begins with a discussion of TDR principles followed by a description of the NUMOD system. An interactive example of signature analysis is then used to demonstrate features of the NUTSA program.

Jan 1, 1993

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965