Search Documents

By Martin J. Gavin

The oil- shale studies of the Bureau of Mines , conducted in cooperation with the State of Colorado and the University of Utah , have for their primary purpose the determination of retorting and refining conditions most favorable for obtaining the highest yields of most satisfactory products . Oil shales , typical of the deposits in several States , are retorted in carefully controlled retorts of differe types , the conditions being varied in successive runs as the results indicate that improvement in the yield and quality of the products most desired may be expected . Each shale presents a somewhat different problem , for it has been found that different shales treated under similar conditions yield products of different natures , and also that the same shale will yield products of different natures when retorted under different conditions . Some shales apparently can not be made to yield , under any set of conditions , products of so high an order as are yielded by other shales . This indicates that the oil -yielding materials of certain shales differ in constitution and in their manner of breaking down when undergoing destructive distillation . Other shales appear to contain oil - yielding materials that resemble each other closely as regards chemical constitution , yet they require some. what different conditions of treatment , if products of similar nature are to be produced from each . In such cases the controlling factors seem to be the richness of the shale that is , its content of oil -yielding material and the physical and chemical nature of its mineral parts .

Mar 1, 1922

By Irwan Halim, Stephane Polycarpe, Brian Hann

The Narragansett Bay Commission Phase III CSO Program includes construction of the 11,600-foot long, 30-foot ID, deep rock Pawtucket Tunnel in Rhode Island. This paper provides an overview of the Design Build Project features and highlight some of the important design considerations, features, and innovations, including geologic conditions and related TBM design, and deep shaft and tunnel segment designs. The paper provides the most recent updates on some of the project construction activities including TBM tunnel progress and retrieval schemes, tunnel pump station and deep vertical shaft liner installations, SEM construction, and microtunneling for the longest adit using Fiberglass Reinforced Polymer Mortar pipes.

Jun 23, 2024

By Hans E. Madeisky, Bruce W. Downing

The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: an orthosite-hosted magmatic sul?de nickel, dunite-hosted magmatic sul?denickel, porphyry copper-gold, and volcanic-hosted high sul?dation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray ?uorescence equipment, already used for grade control at many mine sites, could provide the whole-rock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By Krishna Parameswaran

This paper discusses sustainability considerations in primary copper smelting using selected examples of practices at ASARCO LLC, an integrated U.S. primary copper producer. Using the classic Brundtland Commission definition of sustainable development, i.e., “development that meets the needs of the present without compromising the ability of future generations to meet their own needs,” the paper discusses how copper mining and smelting practices can be made sustainable. The examples used to illustrate sustainability considerations include: (1) adoption of flash smelting; (2) emission reduction and process improvement associated with anode refining of blister copper and the converter retrofit project, and (3) preliminary research findings on alkali treatment of copper smelting slags and copper mine tailings.

By Gennaro G. Ph. D Marino

In order to improve handling of subsidence damages the Illinois Mine Subsidence Insurance Fund supported the development of novel cost-effective methods of repair. The research in developing the repairs was directed towards the most common and costly damages that had been observed. As a result repair techniques were designed for structurally cracked foundations in the tension zone; structurally cracked foundations in the compression zone; and damaged or undamaged tilted foundations. When appropriate, the postulated methods would result in: 1. significant cost savings (over conventional procedures); 2. a structural capacity greater than when the foundation was untracked; and 3. an aesthetic appeal. All the postulated repair methodologies were laboratory and/or field tested. The paper will summarize the essentials of each technique developed and the test results.

Jan 1, 1986

By L J. de Lange

As a material asset for mining entities, the resources and reserves (RR) estimation processes are surprisingly underrepresented in the assurance landscape. When press reports expose them being inaccurately reported, or in merger and acquisitions processes, their importance becomes clear. The impact of erroneous RR numbers (both positive and negative) could have a material impact on an entity’s reputation and value.The technical nature and ‘black magic’ connotations of the RR estimation processes are possibly reasons why audit committees are not actively involved with it. Internal auditors avoid the RR processes for similar reasons. Also the traditional approach to obtain assurance on RR is expensive and is therefore only performed when it is absolutely required.However, stakeholders’ expectations of good governance are growing. Part of this increased focus is based on attaining a higher degree of certainty about the current and forecasted position of the entity. Stakeholders are also increasingly more interested in non-financial areas of entities, as the future success of an entity is more than a set of financial metrics.Consequently, the RR estimation processes should be visible on the agendas of audit committees. Monitoring of key controls is required as part of the governance obligations for senior management and the audit committee. So once it is on the audit committee’s agenda, the question then becomes, how will that agenda be supported by an assurance process that is cost-effective?The main objective of the paper is to describe a model of RR assurance that has been effectively applied in some mining companies. The paper discusses one particular approach that provides an audit committee with the required assurance regarding RR processes. The approach ties the assurance needs of the audit committee to the needs of the technical experts in the entity, therefore involving two important figures. It also offers assurance providers with a model to audit ‘through’ the RR processes rather than ‘around’ them. The paper then discusses top-down and bottom-up approaches that provide assurance at different levels of an entity.A governance audit that focuses on the RR processes is suggested as a top-down approach. A bottom-up approach assesses the design adequacy of internal control processes. A hybrid model is described which meets the needs of diverse stakeholders including the audit committee and the RR community.The hybrid model combines the expertise of professionals in both internal audit and RR. The right balance of these skills directed by a singular approach ensures that a credible result is achieved.This approach is not as expensive as some verification approaches used in the industry and can, as a result, be performed on a more regular basis.The last element of the paper looks at implementation of the reporting mechanism. An assurance process aimed at continuous improvement further enhances the robustness and reliability of RR reported by an entity.CITATION:de Lange, L J, 2016. Resources and reserve assurance processes – a framework for improved governance, in Proceedings International Mine Management Conference, pp 21-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By B. D. Sparks, I. E. Puddington, F. W. Meadus

The continuous separation of bitumen from Athabasca tar sands, with a high clay content, has been demonstrated. Recoveries of 95 per cent or higher have been obtained. Further processing of this product, to produce an accept-able type of crude oil, would require less heat than currently used in the hot-water process. Also, by comparison, substantial savings in equipment and operating costs are indicated.

Jan 1, 1971

By Cummings. J. B., R. Haworth

"THE OPERATION of the Potash Company of America, Ltd., at its plant near Saskatoon, Saskatchewan, is the result of many years of exploratory and development work, culminating in the construction of a shaft, milling, concentrating and other facilities necessary to the production of potash in a marketable form.The possibility that potash existed in •commercial quantities in Saskatchewan was first indicated in 1943, although it was not until mid-1946, when Bata Petroleums penetrated a potash bed at its Verbata No. 2 well near Unity that substantial in-ter.est was developed in the possible exploitation of this important mineral product.The Potash Company of America, which is the largest producer of pot-ash in the Carlsbad, New Mexico area, a district that has been sup-plying about 90 per cent of the North American potash demand, be-came interested in the Saskatchewan deposits •at an early stage. Its engineers made an intensive study of the western Saskatchewan area in 1947 and continued their review of operating problems throughout the next three years.""Potash"" is the commonly used general term applied to the minerals of potassium, of which there are several. The most common mineral forms in which it is produced are potassium chloride and potassium sulphate. The potash content of potassium compounds is ordinarily ex-pressed in terms of potassium oxide (K20) equivalent."

Jan 1, 1960

By I. AITKENS

Turquoise is prized solely for its attractive color ; it is dull and opaque , wholly lacking the brilliant luster that is the chief attraction of transparent gems . The best quality of turquoise is blue , of a soft and pleasing tone , like the color of clear sky but distinctive , as indicated by use of the term " turquoise blue . " Often its value is lessened by a greenish cast ; in many stones the green predominates . A large proportion of the turquoise that is mined is utterly worthless , so inferior and unattractive is its color . The finest grade of turquoise comes from Persia , notable from Nishapur . Large quantities have been mined in the Southwestern States of the United States , and less important deposits have been found in a number of the other States .

Sep 1, 1931

By J. F. Wang, Y. Jin, Z. L. Wang

Smelting reduction as an ironmaking technology for the 21st century has been challenging the traditional blast furnace. The process has many attractive advantages over the blast furnace, however, the massive by-produced coal gas mainly containing CO, H2 and CO2 requires further treatment. From a chemical engineering view, coal gas is a valuable chemical stock and can be transformed into hydrogen-rich synthesis gas. Hydrogen can be directly used as clean fuel and synthesis gas can be used for the production of some important chemicals such as methanol, ammonia and dimethyl ether. Among those chemicals, dimethyl ether as an alternative clean fuel for diesel engine and liquefied petroleum gas has been drawing more attention. It has excellent environmentally-benign behaviours not only in compression ignition combustion, but also in the much lower emission of SOx and NOx. In this work, a combined technology of smelt reduction ironmaking and direct synthesis of dimethyl ether, which will strongly promote the energy efficiency, environmental protection and resource recovery, is proposed and described in detail.

Jan 1, 2004

By Tailoka F.

Various metallurgical residues from iron and steel making processes have been treated by chlorination in excess air with hydrogen chloride gas generated from the combustion of scrap polyvinyl chloride (PVC). The residues include dust from both the electric arc and blast &maces, hydrocyclone overflow, zinc - lead blast furnace slags and dust rich in zinc and copper from copper refining. Chlorination is achieved either directly by mixing the residues with scrap PVC or indirectly in a two furnace system. In the latter, scrap PVC is combusted between 523 and 573 K in a horizontal furnace and the resulting gases are then reacted with metallurgical residues in a vertical furnace at 1166 to 1329 K. Gas chromatography, thermogravimetric measurements, XRD and AAS have been utilised to study the reactions. The recovery of non ferrous metals is as high as 80 to 90 % and only a negligible amount of iron is carried over. The optimum temperature for combustion is between 518 and 573 K. Above 600 K, the evolution of HCI is so fast that sufficient chlorination is not achieved. Analysis showed that no dioxins were present in the gases, the residues or the chlorides.

Jan 1, 1997

By C. B. Alcock, M. G. Hocking

The kinetics of the growth of sulfate layers on blocks of Cu20 has been studied between 688" and 800°C. At 788c the over-all weight increases followed the parabolic rate law, with k = 216 30 sq mg per cm4 min, using a 1:1 entering gas mixture of SO2:02. At 757 after an initial linear period the parabolic rate law was followed, with k = 57.8 10 sq mg per cm4 min. The gas mixture required a platinum catalyst to produce the maximum SOs pressure. The sulfation rate at 757' and 788c was high until all the CUZO had changed into a core of CuO, when it became very much lower. At 757°C marker experiments showed that the sulfates (CuO. CuS04 and CuSO4) grow outwards from the oxide surface, but CuO. CuS04 mixed with CuO was found beneath the markers. At 688 markers were found at the CuO. CuS04/CuS04 interface. Visual observations at 757 showed a liquid eutectic moving beneath the sulfate surface. causing very rapid sulfation and extruding to solidify as thick 'needles" up to 8 mm long. Marker experiments have shown conclusi.cely that CuO grows on Cu20 in air by the outward migration of copper. ThermODYNAMIC measurements on the sulfate and basic sulfate of copper, reported recently,' are followed here by measurements of the rates of formation of these sulfates on cuprous oxide, in order to provide a background for the understanding of roasting processes. peretti2 and McCabe and Morgan3 have shown that the phase Cu20 lies next to Cu2S when the sulfide is roasted under conditions where sulfates will be formed. Since this would present too complex a system for kinetic study, the present work4 has been based on the kinetics of sulfation of the oxide phase. The results of a study of the kinetics and mechanism of the sulfation of cobaltous oxide have recently been reported.4,5 Results on the sulfation of cuprous oxide have also appeared,6 but are at variance with those to be reported here. This seems to be because the previous workers6 did not obtain constant SO3 pressures from the SO2/O2 sulfating gas mixtures used, as will be discussed later. Wadsworth, Leiter, Porter, and Lewis found that the sulfates produced when SO2/O2 mixtures are passed over Cu20 at red heats are CuS04 and the basic sulfate CuO.CuSO4. When the decomposition of CuS04 was followed' by differential thermal analysis, a stage corresponding to CuO .CuS04 was reached before decomposition into the oxide occurred. APPARATUS The vertical furnace used for quantitative studies was a conventional resistance-heated and propor- tionately controlled furnace with an even zone (1 deg) which was 4 cm long. The gas mixtures of SO2 and 02 were made by mixing measured flows from capillary flowmeters and drying over phosphorous pentoxide before passing them into the Pyrex top-piece of the furnace assembly. A mullite tube of bore 2% cm was used as reaction vessel and at the bottom of this tube was a trap for SO3, which condensed as a colorless liquid. The residual gas was led into a fume cupboard for ventilation to the atmosphere. The furnace used for visual observations of needle growth and other phenomena consisted of a transparent silica reaction tube of bore 3 cm, having an optically flat silica window sealed into its wall. The reaction tube was clamped vertically, inside a mullite tube of bore 4 cm and length 42 cm which was heated by Kanthal windings. The window in the silica reaction tube was arranged opposite a hole 3 cm wide and 2 cm tall which had been cut in the wall of the mullite winding tube 19 cm from its top end. A binocular microscope was used to look through the window, illumination being provided by a focusing microscope-lamp offset sideways and downwards. The oxide block to be sulfated was suspended from the removable Pyrex top-piece to the reaction tube, by means of which it was inserted at the start of the experiment, and through which entered the S02/02 gas mixture. The variation of the temperature inside the reaction tube with horizontal and vertical displacement from the window was investigated, and, while it can be said that the temperature was constant 1 deg, its value at a given position was known only to 12 deg. In both furnaces, the oxide block to be sulfated was suspended from a small silica hook immediately downstream from a platinum thimble used as catalyst, which was held on a long silica rod from a Pyrex spring attached to the removable Pyrex top-piece of the furnace. The spring was only included in the quantitative sulfating furnace; its sensitivity was 1.4 cm per g and it was found to be free from creep in a 16-hr test when carrying the working load. The extensions were followed by a cathetometer which could be read to 0.001 cm, corresponding to i0.7 mg. Extensions of the spring were measured on adding weights between 5 and 500 mg to the working load (thimble + oxide block), and Hooke's law was closely obeyed. SAMPLES Cuprous oxide blocks were prepared by oxidizing Johnson Matthey "Specpure" copper sheet of 1 mm thickness (impurities: iron at 3 ppm, silver at 2 ppm, lead, nickel, sodium, and silicon each at 1 ppm, calcium, chromium, magnesium, and manganese each at less than 1 ppm) for 6 days in air at 1000°C in a re-crystallized alumina boat. It has been reported7 that when Cu20 is prepared by heating copper sheet for 1 day the central plane of the blocks produced consists

Jan 1, 1967

By S. P. Kinney

During 1925, at Holt, Ala., the United States Bureau of Mines made a study of the composition of the gases at four elevations in the shaft of a furnace producing foundry iron. A report3 of the work was published in 1927. Some of the results of this investigation are shown in Figure 1. As indicated, the gas at the center of the shaft is low in CO2 content, while the gas in the vicinity of the wall is higher in CO2. The composition of the gases at the top and at the center of the stock column was not far different from the composition of the gas at the top of the bosh. The investigation indicated clearly that lean gas was channeling through the center of the column. More recently the study was enlarged in scope to include investigation of a furnace operating on Lake Superior ores in the Chicago district. A series of planes between the stock line and tuyères was surveyed. Means and apparatus were developed for obtaining, between the inwall and the center of the furnace, the gas composition, gas velocity, and temperature on each plane. A complete report4 of the investigation has recently been published.

Jan 1, 1929

By A. C. Stevenson

THE hoisting equipment selected for use at the Hecla mine in 1907 was one of the first Ilgner type Ward-Leonard controlled hoists put into ser- vice. Development of the Hecla below the 2000-ft. level, which is the ultimate depth of the old equipment, and the additional service required by the "Star," necessitated additional hoisting capacity. It will be our endeavor to give j70u a brief summary of the engineering which determined the selection of the new equipment. The engineer in making his decision as to size, speed, etc., must .make a duty study approximating as closely &s possible the actual opePating conditions which will eventually result. Primarily, it is necessary to know what work must be done. The amount of material which must be hoisted under the maximum condition, as well as its distribution from the various levels of the mine was carefully studied by the mining engineering department, as the ore reserves, their relative-position and the probable method of working them had to be considered. The final figures reached, taking into consideration four different operating conditions, were, in tons per day, as follows:

Jan 1, 1930

By D La Rosa, K Caron, H Mamani, W Valery, R Diaz

The Gold Fields Cerro Corona copper-gold deposit in Peru has heterogeneous rock characteristics in terms of its mineralogical, geological and geotechnical properties. Blast design variations in these conditions directly impact the run-of-mine (ROM) fragmentation, which in turn influences downstream process efficiencies. In particular, when harder ore is processed, throughput and circuit performance may be limited.To evaluate the potential to increase throughput and improve overall plant performance by optimising blasting practices and comminution circuit operation, Gold Fields La Cima engaged Metso Process Technology and Innovation (PTI) to conduct a full process integration and optimisation project at Cerro Corona. Blasting, crushing and grinding processes were reviewed to identify the potential to achieve substantial improvements in productivity when treating the most competent ore types.Site-specific models of the blasting, crushing and milling processes were developed using SmartTagTM ore tracking technology for calibration and validation. Ore tracking permitted locations in the blast volume to be queried against the geotechnical block model to determine the hardness and structural parameters of the feed to the comminution circuit. They also ensured surveys were conducted when ore from the audit blast was flowing through the crushing and grinding circuits.The predictive models developed enabled PTI to demonstrate how changes in blast design influenced both ROM fragmentation and the performance of downstream comminution processes. Outcomes of the project suggested changes to blast designs and comminution practices, and these were partially implemented for a validation trial. The trial demonstrated a 14.8 per cent increase in mill throughput for the specific ore selected for the study, and an average increase of 5.7 per cent for all ore types. There is potential to further increase throughput and process performance if all recommendations are implemented. This paper describes the methodology used and benefits to the operation from the mine to plant.CITATION:La Rosa, D, Caron, K, Valery, W, Diaz, R and Mamani, H, 2015. Blast fragmentation impacts on downstream processing at Goldfields Cerro Corona, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 333–342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Gurubasayya Swamy

This paper presents the performance study of sag mill in the processing of gold ore. Deterioting ore grade and high demand of metals has tremendously influenced the SAG mills. Today?s high capacity Semi-autogenous grinding (SAG) mills expand vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. Semi-autogenous (SAG) mill performance is influenced by ball charge, feed properties, shell, grate, and pulp lifter design. In the performance study of SAG mill, based on the results obtained it can be observed that SAG mill performed better at feed size +4 inch and grinding media consumption 0.90kg/mt. In the present study the effect of crusher bypass on SAG mill performance, an immediate drop of throughput ranging from 10-20tph is observed. Keywords: sag mill, pulp lifters, grinding media, energy, consumption, throughput

Sep 1, 2012

By Chuan-fu Zhang

Li(Nil/3Col/3- xMnl/3)MxO2(M=Ti, Mg) cathode materials were prepared from LiOH?H2O and oxalate precursor. The physical and electrochemical properties were studied by XRD, SEM, cyclic volt-ampere (CV), AC impedance and constant current charge-discharge. The results show that crystal volume of Ti4+ or Mg2+ doped sample is increasing and the electrochemical reaction resistant Rct is decreased at high rate, improving the cyclic performance and rate capability. The effect of Ti4+ doped is better than Mg2+. The sample is well crystallized and simple pure phase with a-NaFeO2 layered structure when doping quantity x=0.025. The second specific discharge capacity of Li(Nil/3Col/3- 0.025Mnl/3)Ti0.025O2 is 143.2mAh/g at 1C,128.0mAh/g at 2C in the voltage of 2.75-4.3V,and still has 140.7mAh/g and 121.7mAh/g after 20 cycles, respectively, keeping 98.25%, 95.07% capacity.

Jan 1, 2009

By S J. Loach

F-Series reconciliations are formal comparisons of estimates and measurements of ore quantity and quality made at pre-determined points along the mining value chain. F1 is the ratio of ‘Depleted Grade Control Ore/Depleted Long-term Model Ore’ and validates the models upon which Resource and Reserve statements are based. F2 is the ratio of ‘Produced Tonnes and Grade/Depleted Grade Control Ore (-) Changes in Pre-Crusher Stockpiles’ and validates that the ore tonnes and grade delineated in the pit are being accurately extracted and correctly delivered to the processing plant. These factors provide important corporate assurance for a mining company by providing quantitative feedback on model-predicted tonnes and block grade estimates. Since 2009, BHPs Western Australian Iron Ore F-Series reconciliations have been calculated in a single, centralised sequel-server database. This software routinely collates data regarding mineral resource block model depletions, grade control model depletions, pre-crusher stockpile inventories and production tonnes and grade measurements and then calculates F-Series factors for both tonnes and product quality. This paper will present case studies where reconciliation factors were used to identify improvement opportunities leading to projects that improved our models and subsequent forecasts of production tonnes and quality. In addition, it will show how reconciliation factors are tools that monitor control during periods of rapid change and provide feedback on the effectiveness of improvement projects.

Sep 18, 2023

By Imane Benhamed, Jaouher Diouani, Laurent Cassayre, Florent Bourgeois, Carine Julcour-Lebigue, Université de Carthage

The attrition-leaching process aims at improving leaching performance when formation of passivation layers at the surface of leached particles is a severe limiting factor, as discussed recently by Julcour and coworkers (Julcour et al., 2015). This paper proposes a geochemistry-based modelling scheme for deriving the window of possible operating conditions for the attrition-leaching process to match the properties of the processed ore. The rationale is that the attrition-leaching process maintains the surface of reacting particles in an unpassivated state by continuous mechanical removal of surface leach layers, so that the process reactions can be modelled from thermodynamic equilibria throughout the duration of the process. The strength of the proposed modelling approach is that it bridges the gap between the properties of the ore and the process operating conditions. The present paper exemplifies the proposed process modelling route for derivation of the attrition-leaching process operating conditions in the context of the leaching of silicate ores, matching model predictions against controlled laboratory experiments. It is shown how thermodynamic modelling, when used in conjunction with a solid knowledge of the phases present in the system, can assist with deciding upon suitable process operating conditions. As an example, this firstprinciple modelling approach predicted that steel grinding medium would be converted into siderite (FeCO3) under a wide range of operating conditions, which led to questioning this initial choice of grinding medium for the attrition-leaching process under mineral carbonation conditions. It is emphasised that the same approach could be applied to ores of greater economic significance.

Jan 1, 2016

By G Harbort, K Quan

Traditional engineering practice for concentrator design uses a mixture of risk minimisation options and capital minimisation approaches. Often this is based on the preferences and experiences of the engineers involved.A geometallurgical approach involves identifying primary lithology, alteration, and mineral dispersion patterns within a deposit to allow representative samples for test programs. This provides a method to infer from laboratory test results meaningful production data for larger amounts of the ore body. Geometallurgical models can be integrated into the resource block model and subsequent mine plan and can assist in predicting when difficulties in the processing route might be expected, allow adjustment of the design to compensate for these or provide an early warning system so that production forecasts can be more adequately developed. Simulation modelling is the process of creating a computer model of a real system based on mathematical logic. In simulated time, the model explores the randomness and chronological sequencing of events observed on real systems. The objective is to mimic the real system with sufficient accuracy to make predictions of real behaviour under experimental conditions. Amec Foster Wheeler often use the ‘discrete-event’ simulation modelling technique. This method is well suited for inclusion of the statistical variation of effects in unit operation, mechanical availability, throughput and operating strategy (based on historical operating data for equipment downtime), operating schedules and equipment capacity. The net result of the simulation model is an analysis that can quantify risks in terms of system performance and capital and operating costs.CITATION:Harbort, G and Quan, K, 2017. Concentrator design – standard engineering practice versus geometallurgy and simulation, in Proceedings MetPlant 2017, pp 195–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017