Search Documents

By G. W. Jones

From evidence made available during the investigation, it was concluded that the first of a series of explosions occurred at 1:15 to 1:20 p.m. September 21, 1951, in an underground vault that housed pressure regulators on the gas-distribution lines that served Brighten. This explosion damaged the pressure regulators and permitted high-pressure gas to enter the distributing mains and individual-service lines. As a part of the gas-distribution system was not provided with means for protection against such excessive pressures, gas gained access to the interiors of many residences in this area and caused a series of disastrous explosions and fires, which took place during a period of approximately 2 hours after the initial explosion in the pressure-regulator vault. Two persons were killed in the first explosion in a residence, and a third person died of a heart attack attributed to the excitement that prevailed during the explosions and fires, Twenty-three persons were listed as injured. Forty-one residences were either destroyed or damaged - 11 by explosion and the remainder by fires, which developed as a result of gas leakage into residences. Fifteen residences were listed as "completely down" or "gutted." Unofficial estimates of property damage ranged from $1,000,000 to $1,500,000. In view of observations made and information obtained during the investigation, recommendations are presented in this report relative to the natural-gas distribution system in Brighton, which may be helpful in the prevention of similar accidents in this and other communities.

Jan 1, 1952

By Mitsuru Tanahashi

In order to develop an effective process for the production of from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at a solar-grade silicon (SOG-Si) 1773K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten M6-8 followed by oxygen gas injection into the melt (Two-stage connecting process). II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection Process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By Mustafa Kumral, Yuksel Asli Sari

Underground mining operations are sensitive to price fluctuations because they usually perform with a narrow profit margin compared to open-pit mining. Furthermore, the economic evaluations regarding operation are based on estimated or simulated grades rather than actual values. These bring a high degree of uncertainty to the viability of an operation. Hence, mine planning that accounts for uncertainty is crucial for underground mining operations. As an underground mining technique, sublevel stoping has geotechnical, curing time, seismicity, cost minimization, and production requirements. A new mixedinteger linear program is proposed that considers the uncertainty associated with net present value using chance-constrained programming. The net present value (NPV) maximization objective is transformed into a multi-objective maximization problem where one objective is to maximize the mean NPV, and the other objective is to maximize the negative standard deviation multiplied by a scalar called risk or reliability level. The balance between the two objectives was maintained by this scalar and was selected based on the reliability level of the project. A case study was conducted with varying reliability levels, and sequences were generated. It was shown that the expected net present value increased at higher reliability levels, and the overall value of the objective function decreased as the reliability level increased. In other words, the variance component penalized the value of the objective function. Moreover, it was observed from the case study that at lower reliability levels, stope grade order bears similarity to the extraction order.

Aug 4, 2023

By Omid Asghari, Seyed Reza Ghavami-Riabi, Sajjad Talesh Hosseini

Separation of geochemical anomalies from the background using various methods for identifying areas of higher mineral potential is a critical first step in Greenfield and Brownfield programs. There are several methods for differentiating anomalous regions from the background. The U-spatial statistics is an effective technique that provides the opportunity of reaching this goal by considering the geochemical sample locations in the separation of geochemical anomalies. In this study, a developed form of the U-spatial statistics method is introduced, which not only considers the existence of anisotropic spatial variations in input data but also reduces the computational (CPU) time. While the previous method is based on the isotropic assumption in the study area and a set of search windows at different times, here, the geochemical anomaly is determined by pasting only one ellipsoid window, effectively combining the flexibility of the U-spatial statistics method with the advantages of geostatistical approaches. This paper compares various approaches (the previous and developed version of the U-spatial statistics method, concentrationarea (C–A) fractal model, and probability diagram modeling) for the separation of anomalous areas in the presence of heterogeneous spatial variations. This is done with an application to a Baghqloom porphyry copper deposit located in southeastern Iran. The high potential areas identified via different approaches show an anomalous region in central parts of the Baghqloom area, which partially coincides with an intense potassic alteration area. Compared to other methods, our algorithm separated the high potential areas at a greater spatial resolution.

May 3, 2021

By R. J. Kuczynski

The U.S. Bureau of Mines operated a 2,000-9 (4.4-lb) batch process development unit for recovering platinum-group metals (PGM) from automobile catalysts. Virgin monolith, used pellet and used monolith catalyst samples were tested. Leaching twice with 1-pct sodium cyanide (NaCN) solution at 160' C for 1 h in a pressure vessel dissolved over 95 pct of the PGM from virgin catalysts and over 90 pct from used pellet catalysts. Over 85 pct of the PGM was dissolved from used monolith catalysts when a third leaching step was added. PGM concentrates as metallic powder containing over 99.8 pct of the dissolved PGM and analyzing greater than 70 pct PGM were recovered by heating the pregnant leach solutions from virgin catalysts to 250' C and used catalyst to 275" C for 1 h. The solution after heating contained primarily sodium carbonate from cyanide decomposition and less than 0.2 ppm total cyanide.

Jan 1, 1993

By D. Tang

The froth zone in a flotation cell is recognised as a region which contributes to the overall flotation performance. Froth recovery is a measure of the efficiency with which the froth phase delivers particles arriving at the pulp-froth interface to the concentrate. Poor froth recovery in scavenger stages is generally attributed to poor froth stability. The key indicators of froth performance: froth recovery, entrainment and water recovery were measured in an OK3 pilot cell installed at a zinc concentrator in Australia and supplied with scavenger feed. Cell hydrodynamic and pulp chemical conditions during the operation of the cell were also measured as well as bubble growth across the froth phase. The objective of the work was to assess the impact of a number of commercial frothers on the froth performance in the OK3 cell and assess the suitability of using bubble growth as an indicator of froth stability.

Jan 1, 2014

By Nii Allotey Odunton

One of the primary responsibilities of the International Seabed Authority?s Secretariat (the Secretariat) is to assess the quantities of metals present in seabed polymetallic nodules in the International Seabed Area under the Authority?s jurisdiction. To carry out this responsibility, the Secretariat periodically undertakes an assessment of the reserved areas in the Clarion-Clipperton region of the northeastern Pacific (CCZ) using the data submitted by the registered Contractors and maintained in the Authority?s POLYDAT database. The results of its most recent assessment demonstrated that the information submitted by the Contractors, though satisfactory for some purposes, does not permit the in situ quantities of metals in these areas to be estimated with a degree of confidence that is comparable to many land-based mineral resource estimates. Our strategy is to divide the work into two distinct but closely related efforts; one to draft a Prospector?s Guide that provides a narrative description of the key geological and oceanographic data that may be related to deposit abundance and metal content, and another that we call the Geological Model, that summarizes and documents the quantitative resource assessments accomplished in the project.

Jan 1, 2005

By Raymond P. Maloney

The Bureau of Mines investigated the White Mountain mercury deposit, in the Kuskokwim River Basin, to better determine the extent of mercury mineralization and to encourage its development by private industry. A program of diamond drilling, augering, bulldozer trenching, and sampling was carried on during four field seasons, from 1960 to 1963, inclusive. Significant amounts of cinnabar, with only trace amounts of arsenic and antimony, occur in dolomite over an area about 4,000 feet long and 1,500 feet wide. The deposit differs from other mercury deposits in the Kuskokwim River Basin by the absence of silica-carbonate and rhyolite intrusives. Small-scale mining was started in 1963 as the result of Bureau investigation and continued during the summers of 1964 and 1965. The investigations indicate that open pit mining might be the most feasible method of working this deposit.

Jan 1, 1967

By Hans Lundberg

IN last year's report on the progress of geophysics, the airborne magnetometer was the featured new development. At that time only a relatively small number of surveys had been made. During 1947, the airborne magnetometer was used in making many surveys and is again one of the high lights of the year in geophysics. This report is mainly concerned with geophysics as applied to the search for minerals exclusive of petroleum. In 194,5 and 1946, the use of the magnetic method reached a peak, partly because of an active period of prospecting brought on by an active mining market, particularly in Canada.

Jan 1, 1948

By Yuri Hovanski, Jingyi Zhang, David P. Field, Piyush Upadhyay

Friction stir welding has gained wide interest in industry and drawn large research attention due to its high level of automation and superior joint performance. In this study we further expand the welding parameters to be of magnitudes higher than those previously reported to lower the cost and enable high volume joint production. Sound butt-joints were produced with aluminum alloy 6111-T4 blanks with welding speeds up to 6000 mm/min. Tensile tests of the joint pieces show >97% joint efficiency in terms of ultimate tensile strength. The T4 natural aging and grain refinement is found to contribute to the superior joint properties. Electron backscatter diffraction (EBSD) analysis is used to qualitatively study the local shear texture inside the nugget zones of the welds. The shear texture result is a good indicator of the material flow directions in the nugget zones. The flow directions behind the rotation tool are found to be flattened towards the top surface of the workpiece when the welding speed is increased, suggesting intense material mixing and transportation along the longitudinal welding direction (WD).

Mar 1, 2018

By S. A. Richards

Business planning in the coal' industry revolves around the production and quality forecast. It is difficult to accurately estimate costs and revenues until the production forecast is made. At mines where production comes from multiple sections, quality is tied to each section's production. Blending becomes a part of the planning process. In order to respond to rapidly changing business climate, a reliable program is needed to accurately forecast the effects of changes in key parameters affecting the production. This paper discusses an efficient, intuitive, and economical approach to underground coal mine planning program which uses a PC-based relational database as the programming platform to forecast production and quality. The program was developed at a major coal company. The relational nature of the production planning data, the programming algorithm, and the underlying principles are discussed in this paper.

Jan 1, 1994

By R. B. Anderson, N. J. Sherren

The mining equipment at the Scully Mine, Wabush, consists of approximately twenty-five large haulage units, eight large dozer-loader applications and seventy other related pieces of service and maintenance equipment. This equipment is operating in sub-Arctic conditions. This pa-per presents a description of the tire maintenance procedures in use here and discusses the tire troubles that are being encountered and the methods of dealing with them.

Jan 1, 1969

"The Ernest Henry Mining (EHM) ore body is an iron oxide copper gold deposit with an average grade of 1.1 percent copper, 0.5 g/tonne gold and 22 percent magnetite. At the end of 2009, EHM converted the ball mill media charge from forged steel to high chrome media. At high pH values (above 10.5), forged media is passivated, so as the pH of the system drops the media corrosion rate increases and floods the system with corrosion products, affecting flotation. As the high chrome media is much more inert, pH has less of an effect on copper flotation response. Given this, the pH in the roughers was dropped from 10.6 to 9.6 and it was found that there was a slight increase in copper recovery and no statistical change in either the rougher or final copper concentrate grades for copper and gold. With the reduction in pH, there was a noticeable reduction in lime usage from 0.85 kg of lime per tonne of ore processed to 0.55 kg/t. This reduction in lime is equivalent to approximately $700,000 per annum at current production rates.INTRODUCTION The Xstrata Copper Ernest Henry Mine (EHM) is situated 38 km north east of Cloncurry, Australia. The mine began as an open-cut operation in 1998 and transitioned to a multi-sourced operation in December of 2011, utilising ore from the newly completed underground mine in addition to ore mined from the Mount Margaret Mining operations. EHM produces a combined copper gold concentrate containing 25 000 t of copper and 35 000 oz of gold annually, utilising a three stage grinding circuit along with a four stage flotation circuit. In addition to this EHM also produces 1 000 000 t of magnetite concentrate annually via a further grinding and three stage magnetic separation circuit. Based on metallurgical test work performed by Magotteaux between 2002 and 2008, the step to change from forged steel media to 18 percent chrome media was taken in 2009 in a bid to alter the pulp chemistry to improve the flotation performance in the plant (Greet, Kinal, Twomey, & Peatey, 2010). This plant trial resulted in: • Increased dissolved oxygen levels within the pulp, • A ball mill discharge Eh shift of 25 mV to more oxidising pulp potentials, and • An EDTA extractable iron percentage reduction. These improvements in the pulp chemistry resulted in an increase of 1.7 ± 0.6 percent in copper recovery and an increase of 2.9 ± 1.7 percent in gold recovery. As the plant trial using high chrome media was successful, the use of the media was adopted as the standard for the ball mill. This implementation opened the door for further process improvements around the flotation circuit."

Jan 1, 2014

By Krishna P. Sinha

An investigation was made to determine the creep behavior of oil shale at elevated temperatures. During the first phase of the investigation, work done on creep behavior of geologic materials was reviewed and triaxial creep tests on oil shale were planned. Tests at temperatures up to 250°C and axial stress up to 3000 psi were conducted at no confinement and at confining pressures equal to 1/3 and 2/3 of axial stress. Wide variations in the elastic properties as well as creep characteristics are exhibited. Creep deformation is more pronounced at elevated temperature but no definite quantitative remarks can be made regarding effect of grade of oil shale due to wide scatter and limited number of data paints. Primary creep can be described by a power law. Secondary creep seems to be an experimental function of deviatoric stress. Teritary creep was not observed within the test duration (24 hours in most tests).

Jan 1, 1983

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The business objectives of a metallurgical project determine targets and constraints, such as the range of products, production capacities, in-service dates, and capital and operating cost parameters. Permitting is usually left to the project team, as are decisions regarding site location, technology, and construction approach. Success requires an orderly methodology, represented in this book by front end loading (FEL) phases: FEL1 examines several alternative approaches; FEL2 ranks and eliminates less economically or technically attractive options; and FEL3 develops the preferred option to the point of major permit completion, with defined scope, schedule, and cost to submit for approval to proceed with implementation in FEL4. Working through FEL1, FEL2, and FEL3, the project definition improves, estimates become more accurate, and project risks are reduced. The project design basis at the end of FEL3 is the control document for project implementation in FEL4.

Jan 1, 2015

By C. E. Seaman, H. Jiang, S. Klima, T. W. Beck, Y. Zheng

Respirable coal dust has been long recognized as a leading cause of multiple lung diseases. Efforts aimed at reducing dust concentration in underground mines have been made, but increases in coal workers’ pneumoconiosis incidence rates over the last 20 years among U.S. miners are concerning. Dust deposition and water spray suppression are two types of dust removal mechanisms in underground mining activities. In this study, laboratory tests were conducted to investigate the respirable dust decay characteristics during deposition and suppression processes in a confined dust chamber. Dust concentration and size distribution were monitored continuously throughout each 60-minute test. A number-basis particle size distribution was used for analysis to capture the changes of smaller size fractions within the investigated dust sample. This study found that around 62.1% of respirable dust particles were deposited at the end of the deposition test. In addition, the final deposition rate for very fine particles can be less than 20%. The results from the suppression test indicate that larger particles were removed quickly; however, sub-micron particles remain suspended through the 60- minute water spray, and particles under 0.5 µm can be considered irremovable dust under single-spray operation conditions. This study also observed the resuspension of a significant amount of sub-micron particles by the water spray. The results of this study provide basic information for improving dust control strategies and can be utilized to improve the water spray performance for reducing airborne dust levels.

Mar 2, 2022

By Liangguo Kang

Coal, as one of the vital sources of energy in China, has raised widespread concerns regarding its safety issues amidst the country’s economic growth driven by coal. To address this concern, this study employed the Kuznets curve, multiple linear regression, and data envelopment analysis models to investigate the impact of Chinese coal economic development on coal mine deaths from 1992 to 2021. The findings revealed a clear correlation between the Chinese coal economy and coal mine deaths. Specifically, per capita coal output, the death rate per million coal tons, and the death rate per hundred thousand persons exhibited positive, negative, and negative correlations, respectively, with the growth of coal income over the past three decades. Moreover, when the coal workers and coal output factors remained unchanged, the income of coal demonstrated a negative correlation with future changes in coal mine deaths. Notably, with three decades of coal economy development, substantial improvements in coal mine safety have been observed in China. Consequently, this research provides valuable insights for formulating safety measures and policies in coal mines across different economic levels, as well as a useful framework for assessing safety development in the coal industry.

Jan 20, 2024

By Guilherme Corrêa Soares

The effects of temperature and strain rate on the mechanical behavior of a superelastic NiTi wire were investigated by uniaxial tensile testing. A universal testing machine with an attached heating chamber was used for the tensile tests. Temperature influence was studied through straining of samples until rupture at a fixed strain rate and temperatures of 25, 50, 75, 100, 125, 150, 175 and 200 °C. Strain rate effects were investigated by straining samples until rupture at room temperature and strain rates of 10-2, 5 x10-3 , 10-3, 5 x 10-4 and 10-4 s-1. The effects of temperature and strain rate on NiTi mechanical behavior were discussed in terms of critical stress to induce martensite and austenite yield strength, when applicable; upper plateau stress, transformation plateau length and ultimate plateau stress. It was found that increasing test temperature and strain rate shifted the stress-strain curve upwards, albeit temperature displayed a greater influence. Plateau length increased with temperature, but no significant changes were detected as a result of different strain rates.

Aug 17, 2017

Gold was determined directly in eight different mill cyanide solutions, by atomic absorption spectroscopy in an acetylene-air flame. Some of the mill solutions were diluted with water to bring them into the most sensitive absorption region (5-50 p.p.m. Au) whereas those solutions with very low gold content «2 p.p.m.) were concentrated by evaporation.Calcium was complexed with ethylene diamine tetra-acetic acid (EDTA) to avoid the undesirable effect of a precipitate on atomization.When added to standard gold solutions, EDTA had no effect on absorption, nor did any of the impurities common in mill cyanide solutions.Known amounts of gold, ranging from 2 to 30 p.p.m., were added to mill solution'aliquots and recovered to within 100 ± 2·5 per cent. For duplicate determinations under normal worKing conditions, standard deviation was 1·32 p.p.m.Excellent agreement was found between atomic absorption gold values and accurate fire assay values.INTRODUCTIONAtomic absorption spectroscopy has been shown to offer a rapid and accurate method for the determination of trace amounts of a number of metal ions. In the field of primary metallurgy atomic adsorption has been used for routine determinations of lead, copper, silver, zinc, cadmium and iron in a variety of raw materials and intermediate products.The scope of atomic absorption spectroscopy was reviewed recently by Willis (1963).The noble metals silver, gold, platinum, rhodium and palladium were determined by atomic absorption from chloride solutions by Lockyer ·and Hames (1959). In their determination of gold down to 1 p.p.m., they found no interference from the noble metals, nor from considerable excess...

Jan 1, 1964

By D. Odendaal, S. Bharat, R. D. Cromarty

The aim of this investigation was to determine the effect of high-temperature heat treatment on the electrical resistivity of charcoal. Samples of two different wood types (eucalyptus and black wattle) were pyrolised in a retort at a temperature of 700°C and the resulting charcoals heat-treated in an induction furnace at temperatures from 800°C to 1800°C and residence times from 60 to 120 minutes. After cooling, the resistivities of the samples were measured at room temperature using the four-point probe technique. It was found that as the heat treatment temperature increased the electrical resistivity of the charcoal decreased, approaching an asymptotic value at higher temperatures. Longer residence times decreased the resistivity, but this effect was not pronounced.

Oct 3, 2023