Search Documents

By J. F. Henderson

THIS paper relates to an area of more than 5,000 square miles in the Northwest Territories extending north from Great Slave lake and including-the Yellowknife, Beaulieu River and Gordon lake areas. Within the last three years much interest in the area has been created by the discovery of remarkably rich gold-bearing veins and the realization that thousands of square miles of unprospected ground are underlain by rocks like those in which the veins have been found. Probably there were more prospectors in this area in 1938 than in any other part of Canada. The area lies 650 miles north of Edmonton, and 425 miles north of the terminus of the Northern Alberta railway at Waterways, Alberta. The Athabaska and Slave rivers provide an excellent water route from Waterways to Great Slave lake for large oil and wood burning boats and barges which operate from the latter part of May to October. The only portage is around a 16-mile stretch of rapids on the Slave river between Fort Fitzgerald and Fort Smith. The town of Yellowknife, on the north side of Great Slave lake, has sprung into existence during the past year and is the centre for distribution of supplies for the Yellowknife-Beaulieu region. The Con-Rycon and Negus gold mines, which came into production in September, 1938, and February, 1939, respectively, lie about two miles south of the townsite. Excellent airplane service is available from Edmonton to Yellowknife and from Yellowknife to all parts of the area. The prospector and mining operator have come to rely almost entirely on the airplane for supplies and for the transportation of personnel, camp equipment, and canoes from Yellowknife to localities selected for intensive prospecting.

Jan 1, 1939

By Shilai Yuan, Huimin Lu, Zhijiang Gao, Panpan Wang

"Solvent refining of silicon through using Si-Al melts is a valid method to remove the impurities from metallurgical grade silicon (MG-Si) melt. The thermodynamic behavior of impurities Fe, Al, Ca, Ti, Cu, C, B and P in MG-Si during the solidification of MG-Si was studied based on the available thermodynamic parameters and experimental data. The morphology of inclusions was investigated by Scanning Electron Microscope (SEM). The chemical composition of inclusions in MG-Si and Al-Si melt was analyzed by EPMA. It is found that the amount of white inclusion reduces and most impurities are solved into the Al-Si melts. After solidification of Si–Al alloy using induction heating and acid leaching, impurities can be effectively removed. The solidification of silicon from the Si–Al melt is found to be more effective for purification than general silicon solidification.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. Multicrystalline silicon has now become the main material in the photovoltaic market because of its low production cost and because of the relative high conversion efficiency of solar cells made from this material, which has been studied for a long time [1-3].Electronic grade (EG) silicon (99.9999999% Si) is commonly used as the raw material to produce SOG-Si (99.9999% Si). Silicon produced from the chemical routes restricts the development of solar cells due to environment threaten, high energy consumption and low productivity. Purification of metallurgical grade silicon (MG-Si) is a low cost, environment friendly method. Although several metallurgical processes such as directional solidification, vacuum refining and electron beam melting [4], have been developed, the cost reduction and refining efficiencies for manufacturing silicon is still have to be further optimized.In the purification process, it is difficult to remove boron and phosphorus by the conventional metal refining method. The refining efficiency depends on the segregation behavior of different elements in solid silicon and the liquid phase. The segregation ratios of all investigated impurities were found to be much smaller than the segregation coefficients between solid and liquid Al-Si melts [5]. For instance, the segregation coefficient of B in Si is 0.8 at the silicon melting point (1687K), whereas it is around 0.2 when silicon is solidified from Si-Al melt at 1273K. For phosphorus the segregation coefficient is 0.06 when silicon is solidified from Si-Al melt at 973K°C, which is much less than 0.35 for recrystallization from liquid silicon. Since the segregation coefficient of boron in silicon is 0.8, it cannot be removed by directional solidification."

Jan 1, 2014

By G Hancock, J Lowry, W D. Erskine, D Jones, T Coulthard, M J. Saynor, P Lu

An 8 ha trial landform was constructed in late 2009 at the Ranger Uranium Mine, located 250 km east of Darwin in the wet-dry monsoonal tropics of northern Australia. The objective of the trial, which comprises two surface cover types on a uniform two per cent slope, is to provide long-term data to guide the development by Energy Resources of Australia Ltd (ERA) of its landform closure strategy. The scope of the work program for the landform includes many aspects; however, this paper is focusing on run-off and erosion rates. The run-off and erosion rates are used to assess the long-term geomorphic stability by comparing measured with modelled export rates from a landform evolution model.Monitoring of wet season run-off is undertaken collaboratively by the Environmental Research Institute of the Supervising Scientist (ERISS) and ERA, on four purpose-instrumented 30 m by 30 m erosion plots. Continuous measurements are made in rectangular broad crested (RBC) flumes located at the outflow of each plot, of water level, turbidity (a surrogate for fine suspended sediment) and electrical conductivity (EC) (a surrogate for solutes). Each plot has a tipping bucket pluviometer located near the RBC flume. Bed load is collected monthly.This paper reports the findings of rainfall and bed load from the first two wet seasons (2009 - 2010 and 2010 - 2011) following construction. The field measured loads will be compared with the predictions made by the Cellular Automaton Evolutionary Slope and River (CAESAR) landform evolution model. Initial results indicate that predicted rates of sediment export from the CAESAR model are similar to measured export rates. This provides confidence in the capability of the model to predict stability of the future rehabilitated mine area, especially during the critical initial years following construction. CITATION:Saynor, M J, Lowry, J, Erskine, W D, Coulthard, T, Hancock, G, Jones, D and Lu, P, 2012. Assessing erosion and run-off performance of a trial rehabilitated mining landform, in Proceedings Life-of-Mine 2012 , pp 123-132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By F Hancock

A rainfall simulator was developed to assist with hydrogeomorphic research into the stability of engineered landforms associated with rehabilitated uranium mines in the Top End of Australia. It can be used in rough terrain with slope gradients up to 30o. The rainfall simulator is modular, utilises upward jetting nozzles, has a multiple head arrangement and is capable of delivering rainfall intensities between 60 and 300 mmh-1 over areas up to 1000 m2 and could be easily modified for larger areas. Rainfall uniformity is commonly in excess of 80 per cent and the kinetic energy approaches that of natural rainfall (The modular design utilises an equilateral triangular array of rainfall stands, constructed from galvanised steel water pipes and flexible plastic hoses. Total construction costs are low. The water supply reservoir is mobile and easily constructed. An example of its use at Ranger Uranium Mine, investigating the effect of cover on rainsplash and rainwash dominated processes shows that vegetation cover is likely to reduce the erosion rate by these processes by at least four times below that experienced on bare areas.

Jan 1, 1997

By Garry W. Warren

The brass foundry industry produces a significant amount of waste sand containing Cu, Zn and Pb which is often classified as a hazardous waste due to Pb content. The potential application of a hydrometallurgical process to treat the sand by extracting metal values and thus detoxifying the material has been investigated. The process involves leaching of metal values followed by cementation. The emphasis of this investigation was on the leaching step, although some preliminary cementation experiments have been performed. In order for any alternative treatment scheme to be successful, the smaller size fractions of the sand must be addressed. Experiments have been performed on five individual size fractions using various lixiviants HCI, acetic acid and HCI/NaCI. Cu extraction was found to be slower than either Zn or Pb. Results obtained in this investigation indicate that copper is present in two forms, an oxide form which dissolves rapidly and is insensitive to the level of oxygen, and a less soluble form, probably metallic which dissolves more slowly and requires an oxidizing agent. The presence or absence of oxygen had no influence on the rate of Zn dissolution indicating that zinc is present mostly in oxide form. Toxicity Characteristic Leaching Procedure (TCLP) tests showed that residues could be produced which meet the toxicity limit for lead. Preliminary cementation experiments have also demonstrated the feasibility of Cu and Pb recovery.

Jan 1, 1991

By T. V. Nethery

Introduction A brief account of the East Malartic fire is essential if this paper is to serve the purpose implied by its title. The fire originated in the timbers of No. 4 shaft at the 10th, or 1,570-foot, level; this was the top or collar of the underground sinking operations. At the time, sinking was in progress and the shaft bottom was 242 feet below the 12th station horizon, or 618 feet 'below the l0th level. Above the l0th level, the shaft was not in use as the surface plant was not yet completed. The shaft crews descended from surface in No. 3 vertical shaft to the l0th level, where they transferred to No. 4 shaft, a distance of 1,450 feet. Of the sixteen shaftmen mucking at the shaft bottom, four were able to reach safety. One shaftman was overcome by fumes midway between the two shafts on the l0th level, while attempting his escape. The remaining eleven men climbed as far as the 11th station and there succumbed to carbon monoxide. No. 4 shaft, inclined at 61 degrees, bad been raised and timbered from the 10th level to surface; this bad been followed by sinking operations below the l0th. Two air hoists had been set up in the footwall of the shaft, 110 feet above the 10th level, and directly behind compartments No. 2 and No. 4. The waste from the shaft bottom was hoisted in 28-cubicfoot buckets on mono rails and dumped over standard shaft sinking doors into waste chutes built into No. 1 and No. 3 compartments. The five-compartment shaft, 7 ft. 8 in. by 34 ft. 6 in. overall size, was heavily timbered. In addition to the standard shaft timbers of 8 in. by 8 in. and 8 in. by 10 in. B.C. fir, the hanging-wall and ends of the shaft were laced with 4-inch spruce lagging. This represented approximately 300 board feet of timber in placee for every foot of shaft. The cause of the fire bas never been determined, despite every effort to do so. The inquest held for those who lost their lives in the fire was an extremely thorough one, but only the location of the origin, and not the cause, was established.

Jan 1, 1950

By E. J. Gleim

In keeping with past custom, it is the purpose of this publication to bring up to date previously published lists of equipment that meets safety standards of the bureau of Mines so that the mining industry may be informed as to the development and availability of equipment that can be used safely. The present lists supplement those in Bulletin 543. Permissible Mine Equipment Approved to January 1, 1953; Information Circular 7722, Permissible Equipment Approved During the Calendar Years 1953-54; and Information Circular [40], Permissible Equipment Approved During the Calendar Years 1955-56. These [ew] lists also contain equipment meeting those standards revised since the last listing. A revision of Schedule 16C (now Schedule 16D4/) was officially approved on September 28. 1958. Schedule 29 was another standard revised in 1958. The revision was officially approved on September 8. 1958, and is known as Schedule 29A5/ .

Jan 1, 1960

By MINE SAFETY BOARD

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions . In recent years these questions have tended to increase with the use of mechanical appliances . Twenty- five years ago electricity had hardly been used in mines . To - day there is practically no other means of transmitting energy employed in American mines , except in metal mines where compressed air is used for drilling and small portable hoists . In coal mines there has been a great increase in mechanization and a tendency to concentrate the mining operation , which has resulted in attendant difficulties of ventilation and intensified the danger of coal - dust in bituminous and subbituminous mines . The answers to the questions which arise are not always obvious , as is shown by the fact that even able , experienced men differ in their opinions of the best way to overcome a particular mining hazard . The difficulty of solving the problems is also demonstrated by the varying provisions in mine safety rules , both in official regulations and in the rules of those mining companies who are endeavoring to do more than follow the letter of the law . Such differences of opinion on the best way of meeting a difficult situation are often found within the same mining organization , and so it has been in the Bureau of Mines .

Nov 1, 1929

By José Roberto de Oliveira

In a smelting reduction process the reduction reaction occurs predominantly in the liquid state. The main reduction agent is the carbon from the carbon saturated iron bath. The aim of the present work was to determine the velocity equation and the rate constant of the reduction rate of MnO content in a Mn0-SiO2-Fe0 slag by iron saturated carbon and the carbon dissolution rate in a Fe-Mn bath. The manganese content in the iron bath was in the range of 5 to 15 wt.%. It was observed that the rates of carbon dissolution in all Fe-Mn baths are faster than the rates of MnO reduction by the carbon saturated liquid iron.

Jan 1, 1999

By M. E. Wadsworth, T. D. Chatwin

The kinetics of sulfidization of hematite (Fe203) by H2S gas at various partial pressures have been determined over the temperature range of 170° to 500°C. The process was controlled by thin films of pyrite (FeS2) and troilite (FeS) which were protective and formed diffusional layers. At higher temperatures the thermodynamic drive to form FeS2 decreased, and consequently the rate of formation of FeS, decreased. Conditions for the development of thin layers of FeSz consisting of 10 to 100 atomic diameters are presented. Laboratory flotation results on synethetic ores indicate floatability identical to that of pyrite of normal xanthate flotation. The prospect of high-temperature sulfidization of metal oxides using H2S, S, or other sulfur bearing compounds is intriguing as a potential activation process for flotation since the thermodynamics are very favorable for a large number of systems. If the kinetic parameters are sufficiently well understood it may be possible to provide surface sulfide layers a few angstroms thick, thus imparting normal sulfide floatability characteristics to the oxide. For thin layers the total sulfur pick-up would be small except for very high surface area materials but in most cases this sulfur could be readily removed by roasting if necessary. The general reactions for the sul-fidization of metal oxide MxO, to a metal sulfide MpSq using H2S may be written for the three conditions py > xq; py < xq; and py = xq: A large thermodynamic advantage is obtained in many systems because of the relatively large negative free energy of formation of H,O compared to H,S. For the temperature range 2S° to 1500°C &apos; where AFOis the standard free energy and T is absolute temperature. As is evident from Eqs. 4 and 5, the free energy of formation of H ,0 is approximately 35 to 37 kilocalories per mole greater than that for H,S over broad variations of temperature. For oxide-sulfide systems as outlined above, sulfidization may be expected to occur for the conditions: Groups I and 111: that is, if the terms on the right are more negative than those on the left the reaction is expected to occur thermodynamically. The value hFg,(,) is included in Eq. 6 since hFLzs is based upon gaseous S2 rather than the normal reference state, orthorhombic sulfur. The

Jan 1, 1969

By A. U. Seybolt, F. J. Norton

A standard technique for heat treating small metallurgical samples where no appreciable contamination from the atmosphere can be tolerated is that of sealing small samples in evacuated fused-silica tubes. Since vitreous silica is relatively impervious to diffusion of gases, even at temperatures approaching the devitrification range, around 1100°C, this simple procedure has been very widely adopted as a standard technique in metallurgical research. Many workers have recognized that, with metals of fairly high reactivity, insulation from direct contact with the SiOz envelope is desirable in order to avoid displacement reactions of the type M + SOz-- MOz + Si(in M). It is not so generally known, however, that the &apos;rate of permeation of oxygen from the air through the SiOz enclosure at tem-

Jan 1, 1964

The recent mine disasters in Australian coal mines have initiated an introduction of Self-Contained Self-Rescuer (SCSR) as component in the development of new escape strategies for miners. These self-contained self-rescuers are closed circuit, demand sensitive breathing apparatus that make oxygen available to the wearer for a nominal period of time. Their operation is completely independent of the surrounding atmosphere. Once properly donned, the SCSR can assist a miner to escape from an area containing smoke, toxic gases or an oxygen deficient atmosphere. The duration of a typical SCSR is usually taken at the point of complete collapse of the breathing bag which is accompanied by an increase in breathing resistance and inhaled levels of carbon dioxide. Because the oxygen consumption (V02) and the heart rate are correlated, a prediction of V02 and consequently the duration of an SCSR can be made by monitoring the heart rate. Thirty-seven volunteers participated in field simulated escape trials at four underground coal mines. The results from the field trials suggested that oxygen consumption depends on the heart rate, the body weight and exercise rating of the miner. All the volunteers were asked to fill out the questionnaires to evaluate the performance of the units. The miners indicated that they could tolerate the inhaled temperature without any difficulty to breathing resistance. A complete statistical analysis of the field results is also presented.

Jan 1, 1997

By William W. Adams

A new record in accident prevention was made by the metal-mining a industry of the United States in 1938, as signalized by a lower fatality rate than in any previous year. The rate was less than half as high as in 1911, the earliest year for which figures are available. A good safety record was also established in the prevention of nonfatal injuries, as the injury rate was lower than in any other years except 1931 to 1935, a 5-year period notable for its unusually low injury rates. Employment was more limited in 1938 than in 1937, both in number of men employed and total number of man-hours worked. The number of workdays per man also was smaller than in 1937. Operating companies reported that 7,233 mines were active in 1938 or some part of the year and that the total number of men employed was 103,027. This figure represents the summation of the average number of men employed as reported by the companies, the average for each mine being that for the period during which the mine was active. The number of employees at all mines in 1938 was 15,402 less than in 1937. Reports covering all mines indicated a total of 188 million man-hours worked during the year, or 21 percent less than the nearly 240 million man-hours worked in 1937. In the performance of this work accidents occurred that resulted in the death of 156 employees and the injury of 1.2,722, each injured employee being disabled for more than the remainder of the clay on which he was hurt.. The fatality rate for 1938 was 0.83 per million man-hours worked, which was 9 percent more favorable than the rate of 0.91 for 1937. Nonfatal injuries occurred at the rate of 67.61 per million man-hours worked, an improvement of 10 percent compared with the injury rate of 75.37 for 1937.

Jan 1, 1941

By A. Elizabet Serna

The weak acid is a by product obtained in a pre-treatment of gases from a copper smelter prior to sulfuric acid manufacture and the main components of this weak acid are: sulfuric acid. copper, arsenic. antimony, bismuth and iron. Usually, this effluent is neutralized with lime and the solid residues are stored in a landfill as a hazardous waste. This work was directed at determining the optimal conditions to recover copper from weak acid using a cementation process before the neutralization of the effluent. The variables investigated are: Effluent temperature, iron scrap amount and acid concentration versus reaction time. The results of these experiments show that the cementation process of copper and the co-cementation of impurities such as arsenic, antimony and bismuth were in accord with the theory of the electrode potentials.

Jan 1, 1996

R. W. Raymond, New York City: As was announced in the Secretary&apos;s note, appended to the pamphlet edition of Dr. Ledoux&apos;s paper, I have undertaken to superintend the preparation of the samples required by his plan, and the ollation for publication of the results reported. Promises of cordial co-operation hare been received already from a number of leading assayers;? and it is to he expected that the data thus collected, and the discussion to be based upon them, will shed much light upon the important question raised in this paper. Although a detailed discussion of methods on the present occasion might be deemed premature, I am sure that suggestions on the subject from members engaged in assaying would be timely and valuable as a preliminary to later and more detailed criticism. Herbert G. Torrey (U. S. Assay Office), New York City : I may say in relation to the losses in the furnace that I have made a number of experiments, and on my little blank form years ago I put down a place for the losses in the cupel. It met with a good deal of opposition among the smelters, but I claimed that it was my duty to give the full amount of the gold and silver present, and that it

Jan 1, 1895

The paper presents results of the mineralogical examination on samples from a bacterial leaching test which simulated in situ leaching for 482 days. Rock fragments (15 to 20 cm) were obtained from the top, the middle and the bottom of a bioleach column. Examination of the samples was carried by electron microscopy and image analysis. The surfaces of the rock fragments were studied to characterize the precipitation products, and cross-section cuts were studied to assess the advance of the bacteria leaching front and the dissolution of the different sulphide minerals.

Jan 1, 1991

By B. Schoevaerts

The ever-increasing depth of mineral extraction presents a challenging environment for hard-rock underground mines. High in situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. Its application in South African underground mining, however, is limited due to the high labour intensity. This paper describes a method of mechanized installation of a chain-link mesh as evaluation at Gold Fields&apos; South Deep Gold mine situated some 45 km south-west of Johannesburg. A purpose-built mechanized roll mesh handler, developed in Australia, was used in this trial. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been specified as success criteria by Gold Fields: ? A 30% faster installation compared to the conventional methodology ? The mesh should sustain any blast damage when applied to the blasting face ? No unravelling of the mesh when cut ? No failure of mesh under normal conditions ? Reliability of the MESHA® installation handler (availability >90% ? Compatibility of the MESHA® installation handler with AC 282 boomers. Although the energy-absorbing mesh combined with yielding rockbolts is a ground support system of choice for rockburst-prone conditions, the operational upsides recognized during the trial imply that this product can also be competitively used in less demanding ground conditions where weld mesh or shotcrete are customarily used as a primary surface support.

Jan 1, 2012

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/ lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By H. O. Poppleton, F. E. Block

This investigation was made to develop a method of preparing high - purity thorium metal in quantities up to 20 kilograms per batch . Several methods for the preparation , purification , and reduction of thorium tetrachloride are discussed . Thorium tetrachloride was prepared by chlorination of decomposed thorium nitrate or oxalate with carbon tetrachloride or phosgene . tion of the crude tetrachloride was achieved by multiple distillations or by filtration of the molten chloride . It was found that high - purity thorium metal could be prepared by sodium reduction of thorium tetrachloride if chloride of sufficient purity were available . Byproduct salts and excess reductant were removed by vacuum distillation , and the resultant thorium metal sponge was consolidated by consumable - electrode or fixed - electrode arc melting . It was demonstrated that metal prepared by this method could be fabricated into bar , rod , or sheet , at room temperature .

Jan 1, 1964

By John J. Sammarco

The functional safety of programmable electronic (PE) mining systems is an international issue and concern. From 1995 to 2001, 11 PE-related mining incidents in the U.S. were reported by the Mine Safety and Health Administration (MSHA); 71 PE-related mining incidents were reported in Australia. MSHA does not have regulations for formal evaluations of the functional safety of PE mining systems. Hence, the National Institute for Occupational Safety and Health (NIOSH), in partnership with MSHA and the industry, generated the NIOSH safety framework for functional safety of PE mining systems. An overview of the NIOSH framework is given; the key framework elements, the safety life cycle and safety integrity levels are detailed. The safety framework approach has impacted the national and Australian mining industries by enabling the industries to advance from an ad-hoc approach to a formalized and systematic functional safety process. In retrospect, valuable lessons were learned for addressing functional safety and for changing industry perspectives and practices. These lessons continue to benefit mining and are applicable to other industries as well.