Search Documents

By R. G. Zaripova, N. D. Ryan, H. J. McQueen

The austenitic and ferritic stainless steels do not undergo any phase transformation that induces very fine grains in the product through thermomechanical processing as practiced in most other steels. Considerable grain refinement can be achieved by intense multistage deformation descending through warm to cold working; notably multi-axial forging of bulk material can attain high strains with diminished risk of cracking. Hot working to improve ductility yields finer grain sizes as the T is reduced and strain rate E raised; increased strain has limited effect due to the steady state regime. Ferritic steels develop subgrains with size diminishing as E rises and T falls with the advantage of retained strain hardening; recrystallization delivers grains several times the cell size. In austenitic steels, dynamic recrystallization (DRX) provides finer grains at higher E and lower T with a lower limit due to intergranular cracking. The DRX grains contain a strengthening substructure that can easily be retained by quenching; if static recrystallization is allowed to occur the grain size rises markedly. Multistage rolling with diminishing T is able to provide grain refinement to the same degree as straining at the finishing T yet provides better ductility. grains on recrystallization. As a result of the strain induced transformation to martensite, small subzero deformations of austenitic or duplex steels produce very high dislocation densities that yield marked grain refinement when they revert upon reheating.

Jan 1, 2004

By Frank Callanan

The Ameristar Casino expansion project included the design and construction of a 25-story hotel and 9-story parking structure expansion. The site is located in a floodplain on the banks of the Missouri River in Saint Charles, Missouri, where the underlying soils are potentially liquefiable. The geotechnical engineer performed subsurface exploration and analysis, which included site-specific seismic response and liquefaction, and provided geotechnical design recommendations. In the event of an earthquake, post-liquefaction settlement was calculated to be approximately 14 inches. Additional project constraints included wetlands protection, construction adjacent to the existing facility, flood protection and river bank stability. Because of the liquefaction issue, the geotechnical engineer consulted with a specialty geotechnical contractor on ground improvement methods. This consultation led to a proposal to eliminate deep foundations from the design and support the structures on shallow and mat foundations. The geotechnical engineer assisted the design team with foundation design analysis and value engineering assessments. Together with the project team, the geotechnical engineer used the data to evaluate foundation options and construction methods to overcome the site challenges and concluded that ground improvement was the optimum course of action. Because of the nature of the site constraints, a number of ground improvement methods were needed. The geotechnical engineer evaluated the methods proposed by the geotechnical contractor and provided the technical specifications for the ground improvement bid package, which included vibro-compaction, compaction grouting and micropiles. The ground improvement allowed for the use of shallow foundations (mat and spread footings), which provided the client with significant time and cost savings over the deep foundation alternatives.

Jan 1, 2009

By P. Nelson, R. O’Connell, J. Rostami

Tunnel boring machine (TBM) system utilization is a critical factor for predicting machine performance. The process of estimating machine performance, including rate of penetration (ROP) and machine utilization (U) must incorporate an understanding of site geology, TBM specifications and site management. The study herein presents a preliminary analysis of the different activity time and downtime components from hard rock TBMs at two project sites to evaluate their impact on machine utilization. A comparison of crew experience, first between shifts and then between projects is included to analyze its effect on utilization and downtime. This work presents the sensitivity of the utilization factor to selected activities in the projects and the impact of geology and site set-up/logistics on machine performance.

Jun 13, 2021

By E. S. Shedd

The Bureau of Mines investigated electrowinning and tapping lanthanum metal from lanthanum oxide in a fluoride bath. The electrolyte was composed of LaF3, BaF2, and LiF. Metal containing 0.2 percent impurities was produced at a rate of over 2 pounds per hour. Principal impurities were carbon, aluminum, and silicon. Low-carbon metal was produced by continually discharging the carbon oxide gases and maintaining 0.1-atmosphere pressure. Anode reactions and cell design were found to be important factors in cell operation. Both frozen electrolyte skulls and tungsten metal crucibles proved satisfactory for collecting the metal and did not react with the molten lanthanum.

Jan 1, 1966

By J. L. Morning

During recent years, the Bureau of Mines has conducted an extensive investigation of the materials for making iron and steel. This work includes iron ore concentration, agglomeration, direct reduction of iron ores and concentrates, the production of pure manganese, chromium, and cobalt by electrolytic processes, the production of ferroalloys from low-grade domestic ores, and the development of special alloys to utilize these products. As a part of this general program, a Congressional appropriation allowed the con¬struction of an electric-furnace, semicommercial, ingot-producing plant at Shasta Dam near Redding, Calif. The primary objectives of the pilot plant were to determine the costs and operating problems involved in the production of steel and ferrous alloys in which sponge iron was used as melting stock, and to determine the physical properties of the materials produced. The pilot-plant equipment and the results of sponge iron-melting tests in the basic lined, electric arc furnace have been reported in previous publications.3/4/

Jan 1, 1953

By III Cocanour

The line scan video photometer is a personal computer (PC) based, software-driven instrument which is used for the real time, on-line analysis of industrial process streams. The novelty of the instrument lies in the integration of its various components: (l) a true Red/Green/Blue (R/G/B) color video camera; (2) a unique, line-scan color sample and hold technique which provides a 4 to 20 mA analog signal to a commercial 12 bit analog to digital (A/D) converter; (3) software which converts data through a color absorbance algorithm to correlate elemental color to concentration; and (4) software-based control which utilizes color data, along with temperature and conductivity data to control process equipment. The photometer can be used for noninvasive analysis wherever color hues are representative of process variables such as chemical concentrations or mineralogy color reflectance. The line scan video photometer has been successfully demonstrated in solvent extraction/electrowinning (SX/EW) and ball mill circuits of copper producers.

Jan 1, 1996

By C. G. Anderson

As the global demand for copper and gold steadily increases and the need for environmentally sound processing also grows, successful hydrometallurgical treatment of enargite (Cu3AsS4) concentrates has come to the forefront. This type of concentrate contains considerable arsenic so that successful arsenic fixation, for example as scorodite, is of the essence. This paper outlines the successful application of low temperature and low pressure nitrogen species catalyzed (NSC) hydrometallurgical pressure oxidation of enargite concentrates. The successful stabilization of the arsenic as an iron arsenate compound is discussed. Also, the use of experimental design software is highlighted as a process application and optimization tool.

Jan 1, 2006

By S. M. Pickering, L. T. Gregg

Appraisal of industrial minerals beneath privately owned land requires a different approach and mindset from valuation of base and precious metals or energy minerals, and from valuation of government-owned mineral lands. First, is it the value of inground minerals or of mining rights that is being sought? Second, value to whom, the mining company, a potential investor, the mineral landowner, a lending institution, the property tax assessor, or a condemnor? Third, how should mineral value be apportioned between the land and mineral owner, and a mining company with limited years of lease-hold interest? These and many other questions must be addressed before a valuation method and Discount Rate are selected. For various reasons the Income Method is most often used, with Net Present Value calculations made for long term predicted mining income. Choice of an appropriate Discount Rate is critical.

Jan 1, 2000

By M M. Collisson

The Synthetic Rutile (SR) plant operations, North Capel, produce electrostatic precipitator (ESP) fume and kiln scrubber residue. Typically ESP contains about 18 per cent Ti, 13 per cent Fe, 0.5 per cent Mn, eight per cent Si, six per cent Al, 16 per cent C, 0.9 per cent Zn, 0.6 per cent Pb, 300 ppm As, 300 ppm Cr and 5 ppm Cd. These wastes are held in a storage dam together with neutralised acid effluent (AE) liquor. A project was initiated to treat the fume and produce a benign residue that could be delivered to landfill, reducing dam space storage. Plant AE, containing free acid (9 - 14 g/L), Fe (6 - 7 g/L) and Mn (1 g/L), was used to leach ESP. The degree of extraction achieved for various elements include about 20 per cent Zn, almost 50 per cent As, five per cent Al, 0.4 per cent Pb and 15 per cent Cd. Extraction was most effective at pH The residue from AE leaching still contained Pb. TCLP tests of the leach residue produced Pb extraction significantly higher than the 0.1 ppm stipulated by Class 2 landfill guidelines. Other elements (eg As, Cd, Cr) successfully met the limits. Further leaching of the residue with EDTA extracted up to 65 per cent of Pb content. TCLP tests on treated residue showed Pb leaching potential of Lead was removed from the leach circuit as the sulphate by acidification of EDTA leach liquor, allowing EDTA to be recycled. The study showed that one waste stream can be used to treat another and help reduce plant waste.

Jan 1, 2001

By J. D. Doherty

That America's great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Increase imports. 3. Develop new sources such as synthetic liquid fuels.

Jan 1, 1949

By R. Thornton

Montana Tech is located in the historic mining town of Butte, MT and is adjacent to the Orphan Boy mine. This abandoned underground mine will be the heat source for a down-hole heat exchanger (DHE)/heat pump system. The mine was abandoned in the 1950?s and has since filled with water to within approximately 30 m of the surface. The shaft is composed of a 245 m vertical shaft connected with horizontal crosscut drifts at 60 m and 150 m below the water level that connect to a large stope with approximately 1250 million liters of water at a consistent 75-78°F temperature. The intent is to build this heating system to augment or fully heat a newly built 2,000 m2 building on the Montana Tech campus. As designed the system uses ?off-the-shelf? parts making the basic configuration straightforward with the exception of the DHE?s which need to be placed into the vertical shaft. Because there is little or no examples of placing the heat exchangers in a vertical shaft, the primary focus of this work was to model the heat exchanger placement and configuration in the vertical shaft such that thermal currents develop between the stope and vertical shaft in, via the horizontal crosscut drifts, in order to move the water and thereby provide the required energy. This study includes the modeling of water flow, temperature profiles, and the heat contribution from the surrounding rock walls.

Feb 27, 2013

By K. A. Natarajan, M. R. Sabari Prakasan

"Biodegradation of sodium isopropyl xanthate using two types of bacterial strains, Paenibacillus polymyxa and Pseudomonas putida, is demonstrated. At concentrations higher than 50 mg/L, the presence of xanthate in the growth medium resulted in bacterial toxicity, retarding growth kinetics. Adaptation through serial subculturing in the presence of higher xanthate concentrations resulted in the development of xanthate-tolerant bacterial strains. Stress proteins secreted by bacterial cells grown in the presence of xanthate were isolated. Bacterial cells could utilize xanthate as a growth substrate, degrading xanthate species in the process. Acidic metabolic products generated by bacterial metabolism promoted efficient xanthate decomposition. Probable mechanisms for the biodegradation of isopropyl xanthate are illustrated.IntroductionDifferent types of alkyl xanthates (ethyl, isopropyl, amyl, etc.) have been used as flotation collectors in the concentration of sulfidic ores for several decades. Large quantities of waste water and xanthate-containing effluents are generated by ore flotation processes, posing considerable environmental challenges. Billions of cubic meters of such process waste waters are produced annually across the world, most of which are discharged to the environment, often without any treatment. Leakages and accidental release of xanthate reagents from manufacturing plants and during transportation and storage can also contaminate the environment. Residual concentrations of xanthate reagents are encountered in waste effluent, which are found to be toxic to aquatic life and unfit for human consumption (Harris, 1984; Okibe and Johnson, 2002). Further, direct recycling of such waste waters for plant operations can compromise water quality standards required for process operations. The presence of residual xanthate in recycled waters from flotation plants deleteriously influences flotation processes. Xanthate can be easily decomposed at low pH values; however, CS2, which is more toxic, will be produced by the acidification of neutral and mildly alkaline xanthate-containing solutions. Physico-chemical methods such as flocculation, chemical oxidation and decomposition and physical adsorption used to remove residual collector reagents from mill process waters are often expensive and not environment-friendly (Oliveira and Rubio, 2009; Cheng et al., 2012; Molina et al., 2013,)."

Jan 1, 2015

By Pratima Meshram Abhilash

In this review, availability of germanium in primary and secondary resources and its recovery from these resources are presented. With nearly 40% germanium consumed in fiber optics and scarcity of resources, the global consumption outplays the primary production. Germanium exists as a substituted element in zinc sulfide matrix of lead–zinc sulfides and lignites. Nearly 60% of the germanium supply is met by zinc refining residues, and about 20–30% of germanium is produced from coal and its by-products. Germanium recovery from various resources such as zinc plant residues, coal and coal plant waste, spent optical fibers, and copper flue dust has been examined. Bioleaching was exploited by few researchers to extract germanium from zinc sulfides, sulfide tailings, jarosite, coal fly ash, and flue dust. This review covers the various work carried out by different chemical separation processes, viz., chemical precipitation, solvent extraction (SX), ion exchange (IX), and membrane processes, as well as biological approaches.

Jan 16, 2022

By W. Todd

The Robbins Company has developed a boring machine, with a rubber packer serving as the gripper system, for blind boring of raises without using drill pipe. This machine is the BorPak and has many applications for use in the mining industry which will improve productivity. In addition to the cost savings, the boring method will lead to increased safety in constructing blind raises. The advantages of using the BorPak in a mining environment will be discussed together with possible applications.

Jan 1, 1994

By David Mitchell, Daan Delport, Frik Marx, Mike Shapiro

The use of copper cooling elements to enhance refractory lining life in pyrometallurgical vessels is common in modern furnace design. Copper elements typically incorporate a base panel with cast in cooling passages and an integral extended surface (formed of pins, fins or similar) onto which suitable refractory material is cast. The metallic, conducting parts are located towards the cold face of the lining, with the refractory material interposing between the coolers and the process. The coolers are designed to arrest wear of the refractory material by freezing a layer of slag or partially reacted material onto the hot face, thereby rendering the lining inert to further attack [1]. These coolers have achieved success in new furnaces and relining of existing vessels. The freeze layer is prone to mechanical damage during operational and process instability. The coolers must be capable of extracting the additional heat flux under upset conditions to facilitate rapid self-repair of the freeze layer and prevent further refractory wear in the intermittently exposed areas. However, operational experience has shown that the high heat flux capabilities of the copper coolers have some disadvantages, especially in processes producing vapours which form corrosive compounds when condensing onto the cold surfaces of the coolers. When corrosive conditions develop, the entire composite will fail due to loss of structural integrity, and as a result of leaks from the cooling water passages. This paper describes recent developments in the approach to the design and manufacture of copper cooler panels customized to achieve specified heat fluxes and temperature profiles, thereby reducing the formation of corrosion mechanisms in applications with corrosive gaseous environments and enhancing refractory lining life. Condensation formation prevention is achieved by adjusting the geometry of the cooler and selection of suitable materials of construction.

Jan 1, 2007

By O. M. Johnson

Barite and bentonite are the two principal components of drilling fluid systems used in the petroleum industry for oil and gas well drilling with rotary-type rigs. Approximately 87 percent of the world's annual production of barite is used in drilling applications. Of the worldwide production of bentonite, an estimated 30 percent is used. The drilling fluid, or drilling mud, to which barite and bentonite are added, performs five distinct functions: Lubrication-The liquid phase of the drilling mud lubricates the drill bit, preventing premature failure of the cutting edges and bearings. it also helps to soften the formation being drilled. Cuttings Removal-A mud system must be able to carry rock cuttings broken loose by the bit up to the surface where they can be removed by mechanical or chemical methods. The fluid's ability to perform this function depends upon maintaining a proper balance between the rate of circulation of the fluid and the colloidal properties required to entrain the cuttings in the mud to prevent their settling to the bottom of the hole. Hole Stability-The pressure exerted by the mud against the wall of the bore hole prevents the collapse of the uncased portions of the hole. Downhole Information-The fluid characteristics of the mud should be such that good cuttings samples, cores and electric logs may be obtained to help evaluate a well's productive zones and potential. Control Oil, Gas and Water Flows-It is essential that a drilling fluid offset any pressure from naturally occurring formation fluids in order to prevent a potentially wasteful and dangerous blowout.

Jan 1, 1980

By J Stipcevich, N Patel, J Faithful5, S Narendranathan, L Tatnell4

ENGIE, the current owner and operator of the Hazelwood Open Cut coalmine, are in the process of rehabilitating the mine site in preparation for mine closure. Bucket wheel excavators (dredgers) used during coal mining operations are in the process of being demolished, which involves the controlled felling of dredger components using explosives. With the mine located in close proximity to the Morwell township and other critical public infrastructure, it is crucial that the use of explosives and the possible implications for mine stability is well understood. The felling of Large Mining Equipment (LME) will apply an impact load immediately to the underlying coal benches with the adjacent coal batters potentially at risk also of adverse slope stability impacts. This paper presents the 3D stability modelling methods employed to successfully assess the potentially adverse stability implications associated with LME collapse.

Jun 21, 2022

Cansolv® S02 Scrubbing Technology was described in a paper in Copper/Cobre 03. Four years on, the technology is operating at a full scale production facility.Hindustan Zinc Limited expanded their capacity by installing the AUSMELT process. The process proceeds through smelting, slag reduction, slag cleaning and holding stages sequentially in the same vessel, resulting in widely varying off gas characteristics. The off gas is suitable for treatment is a conventional acid plant for a modest proportion of the day, but at other times produces off gas too high in S02 to be discharged to atmosphere. Cansolv® S02 Scrubbing Technology was identified as a means of effectively removing the S02 down to low levels from the off gas during all stages of the pyrometallurgical process. Furthermore, the Cansolv® S02 Scrubbing System Technology produces high purity S02 that allowed for the captured S02 to be directed to an existing acid plant, avoiding the capital cost of new acid making capacity.

Jan 1, 2007

By D. C. Austin, P. J. Hazell, A. A. H. Ameri, J. P. Escobedo-Diaz, D. East, M. A. Bevan, A. D. Brown

Additive Manufacturing (AM) has become increasingly popular due to the ability to produce components with complex geometries and properties. The efficiency of this manufacturing method is investigated in this paper by examining the mechanical performance of AM austenitic stainless steel 316L under different strain rates. Dynamic compression experiments were conducted by using a Split Hopkinson Pressure Bar (SHPB). Microstructural observations were performed by utilizing optical microscopy. The behavior of this material is compared against stainless steel 316L manufactured by conventional methods. The results show that theAM316L used in this study display a considerable difference in the mechanical properties compared with conventional stainless steel alloys.

Mar 1, 2017

By E. E. White

(Cleveland Meeting, October, 1912.) IN, August, 1911, I read a paper before the Lake Superior Mining Institute' on surveying and sampling diamond-drill holes. The present paper gives a more thorough description of these methods, together with a few changes and notes suggested by further experience. Since August, 1911, the methods, used constantly by the Cleveland-Cliffs Iron Co., have been developed to a higher degree of efficiency, and have given great satisfaction. Until a few years ago but little attention was paid to the determination of the actual course of drill-holes, to the accurate sampling and analysis of the material, or to the scientific location of the drill-holes. It has now been common practice for several years in many districts to test the inclination of drill-holes by etching glass tubes with hydrofluoric acid, but the direction of deviation from the vertical has not often been determined. Methods of determining the direction by means of a compass were first developed in connection with drilling in Victoria. The latest method used on the Rand in South Africa has been recently described by John I. Hoffman.2 In the same paper Mr. Hoffman describes an ingenious method of wedging-off a drill-bole so as to start new holes at several successive points. By this means a hole can be deflected in any desired direction, and the curvature can be controlled to a considerable extent, provided the rock is soft enough to permit the hole to be wedged off. Unfortunately, in the Lake Superior district, the jasper iron-formation is so hard that it is very difficult, if not impossible, to do this. I tried to deflect one hole so as to avoid drill-rods stuck in the hole, by using a 1 Proceedings of the Lake Superior Mining Institute, vol. xvi., pp. 100 to 120 (1911). 2 Recent Practice in Diamond-Drilling and Borehole Surveying, Bulletin No. 91, Institution of Mining and Metallurgy (Apr.. 11, 1912).

Nov 1, 1912