Search Documents

By H. Oda, L. E. Fong, K. K. McBride, B. P. Weiss, F. J. Baudenbacher, A. Usui

Fine-scale dating is a key parameter in characterizing the growth history of hydrogenetic ferromanganese crusts. We once compared several dating methods, micropaleontological (calcareous nanofossil), radiometric (10/9Be), and paleomagnetic (step-wise measured inclination) methods on single samples, but these independent methods were not consistent with each other (Joshima & Usui, 1999). For example, a 4-cm thick crust was dated as 3Ma by the fossil-paleomagnetic combined method, while it dated older than 5.5 Ma by Be-10 dating. This discrepancy suggests a question if the Be-10 radiometric method can give us false ages or growth rates (Usui et al., 2002) because of post-depositional change, diffusion or other reasons. In order to answer the question, we conducted ultra-fine magnetostratigraphy with a SQUID microscope on the same hydrogenetic Mn crust sample. Rock magnetic measurements revealed that the main magnetic mineral is well dispersed single domain grains, which is typical to magnetite but not yet specified (Oda, 2005).

Aug 24, 2006

By K. E. Tame

A resume of the history and state of the art of physical beneficiation of uranium ores is presented along with a detailed description of research on concentration of uranium ores by attrition grinding. The information on flotation, gravity concentration, electronic sorting, and selective grinding was gathered to complement the study of attrition grinding methods. Both dry and wet grinding procedures were investigated as potential methods of upgrading a variety of ore types, ranging in grade from 0.02 to 0.42 percent U308. A Mardun4 disintegrator that employs high-speed rotating paddles in a cylindrical shell lined with interrupter bars was used in most of the dry grinding studies. Attrition scrubbing devices, which impart a violent mixing or attritioning action to ore pulps, and cylindrical mills, employing rods or punchings as grinding media, were used in the wet grinding tests.

Jan 1, 1961

By J. A. Finch

"Much progress has been made over the last several years in the ability to measure flotation cell hydrodynamic parameters in both the laboratory and plant. These techniques have allowed fundamental research to proceed to determine the effects that frother chemistry has on the main hydrodynamic parameters (gas hold up, bubble size) as well as on the amount of froth generation and water content of froth. A research program was begun that brought together a team consisting of private companies and a University with expertise in hydrodynamic characterization (McGill), flotation reagent applications (Flottec) and chemical synthesis (Sasol N.A.) with the purpose of characterizing frother chemistries with two goals in mind: Determine which frother chemistry can provide optimized cell hydrodynamics; and, create new frother chemistries with specific hydrodynamic properties.This paper describes the key steps that were taken that led to the development of new frother chemistry for use in flotation.The first step was the characterization of the major frother chemical families in a two phase system. The parameters measured were gas hold up, bubble size, froth height and water carrying rate at different concentrations and gas velocities.Analysis of the data indicated that definite patterns existed between frother chemistry and hydrodynamics and showed that frothers could be grouped into classes. More importantly, by modifying known frothers through chemical reaction it was shown that these frothers could be moved from one class to another. As a result of this better understanding of the interdependence of hydrodynamic and chemical properties, a new frother chemistry was proposed that was predicted to perform similarly to MIBC.The new frother was synthesized and hydrodynamic testing confirmed that the chemical performed similar to MIBC. Laboratory flotation tests were conducted on two different ore types that also confirmed the similar performance of the new chemical and MIBC. Subsequently, the new product was placed on a plant for a short period of time. The results showed that the product was an excellent frother but increased the flotation rate slightly more than MIBC at the same addition rate.Further research showed that the new frother chemistry was a family of products. By changing the reaction the resultant products could be made to be slightly weaker or stronger than MIBC but that this chemistry cannot provide hydrodynamic/froth characteristics similar to strong frothers like glycols and glycol ethers. Further work is planned to conduct longer plant trials to confirm the efficacy of this new frother family."

Jan 1, 2007

By M. M. Masood, G. Y. Raju, T. Verma

The inverse velocity method has proven to be an effective approach for predicting slope failures in surface mines by analysing displacement monitoring data. However, the accuracy of inverse velocity method predictions is significantly affected by instrumental noise and natural environmental variations, which influence the identification of different deformation stages. To enhance predictive accuracy, this study applies and evaluates three filtering techniques to velocity time series data: Exponential smoothing filter, short-term smoothing filter, long-term smoothing filter and also compares it to raw data (no filtering). A refined prediction framework, that is, filtered inverse velocity method analyser, is proposed to improve slope failure forecasting in surface mining operations. The results demonstrate that filter selection plays a crucial role in optimising failure time predictions, offering valuable insights for geotechnical monitoring and early warning systems in surface mines.

Sep 1, 2025

By Montaser S. El‑Salmawy, AHMED A. S. SEIFELNASSR, Ahmed Al‑Abady, Abdeaziem M. Abdelaal, Amr F. M. Ibrahim

Iron is a key detrimental impurity in silica sands that determines their contribution to high-technology industries. Herein, a simple ecologically sound approach is investigated for iron removal from a silica sand sample obtained from the El-Zaafarana area-Egypt. The sample was subjected to a detailed microscopic mineralogical study supported by XRD and XRF characterization. The sample was beneficiated using distilled water attrition scrubbing and screening over a 25 μm sieve followed by leaching using a mixture of equal amounts of phosphoric and oxalic acids. Leaching experiments were designed and analyzed using the Box-Behnken design (BBD) methodology. A model was developed and evaluated using the analysis of variance technique to map the relationship between the residual iron oxide in the produced concentrate and selected variables such as leaching temperature, oxalic acid, and phosphoric acid concentrations. XRD and mineralogical analysis reveal that quartz is the most dominant constituent of the studied sand and other minerals such as kaolinite, iron oxide, rutile, and zircon exist in trace amounts. The head sample shows a silica and iron oxide content of 95.69% and 2379 ppm, respectively. Attrition and separation over a 25 μm sieve increase the silica content to 97.05% and decreases the residual iron oxide to 455 ppm. The final product after leaching under optimized conditions shows 99.82% silica and 55 ppm iron oxide.

Aug 30, 2022

By B. McFadzean, M. Tadie, T. Dzingai, M. Becker

Ores from a single deposit may exhibit extensive variability in their mineralogy and texture. The ability to quantify this variability and link it to mineral processing performance is one of the primary goals of process mineralogy. This study focuses on the effect of alteration in three platinum group element ore samples from the Great Dyke in Zimbabwe – two of which were more pristine compared to the third, which was locally classified as ‘oxidized’ ore. These ores are known to be characterized by varying degrees of alteration, resulting in numerous challenges in flotation and affecting both grade and recovery. Alteration, by near-surface oxidation, of the valuable base metal sulphides and platinum group minerals resulted in lower flotation recoveries of Cu, Ni, Pt, and Pd. Evidence of incipient oxidation was more readily observed in the base metal sulphide assemblage than the platinum group mineral assemblage, even though the loss in recovery (because of oxidation) was most significant for Pd. Alteration through hydration resulted in a significant increase in mass pull and dilution of concentrate grade through the inadvertent recovery of naturally floating gangue comprising composite orthopyroxene and talc particles. In this study, the amount of naturally floating gangue was more strongly correlated with the talc grain size distribution than the grade of talc in the flotation feed. The oxidation and hydration alteration reactions are not necessarily mutually exclusive, although one may be more dominant than the other, giving rise to ore variability.

Sep 1, 2021

By S. Fabich

Since the very beginning of Polish copper mining, special consideration of sink shaft techniques through highly saturated Cenozoic rocks was required. Shaft freezing has been chosen as a method to consolidate these rocks. Due to the rock mass structure and water inflow potential, shaft sinking without freezing was considered dangerous. In the course of time, rock mass freezing technology and experience were evolved and this technology became safer and more reliable. New techniques appeared not only in the technical method of freezing, but also in the matter of designing. Computer aided techniques allow engineers to make a detailed analysis and view of freeze wall development. Nevertheless it is important to determine basic thermal rock properties. In this paper, the evolution of knowledge and engineering experience taken in Polish copper mines and current knowledge level in that matter were shown.

Aug 1, 2013

By J Wallis

The stability of a raise bore is often assessed using the rock mass classification system published by McCracken and Stacey as a modification of the Q system. Often the assessment is done using a spreadsheet to manipulate geotechnical log(s) of boreholes. This paper discusses the inherent difficulties with this approach. Recent work by others to provide guidelines to the classification system is discussed. A recent example of the design and raise bore performance at Macraes Gold Mine, New Zealand is presented. A key issue is that a visual assessment of the drill core and/or core photographs is necessary to æground-truthÆ the classification.

Jan 1, 2008

By J. A. Bartnik

Flocculation, the process of coagulation or coalescence of finely divided particles, is commonly used in separating fine solids from fluids. Forces disposing of the particles to flocculate include: ionic forces of attraction, secondary entropic forces, and magnetism. Magnetic flocculation is due to a physical magnetizing process which affects suspended ferromagnetic particles. Such particles, after exposure to magnetic fields strong enough to cause reorientation of the particles and alignment of the induced magnetic poles, tend strongly to retain this induced magnetism, as the magnetic retentivity of ferromagnetic particles is a linear function of its specific surface.1 Thus, because they become small magnets with high residual magnetism, the particles become and remain attracted to one another, forming large agglomerates. Fine magnetic particles close to domain size can exhibit energies of the magnetization of the order of 105 ergs/cm3,2 which is many times greater than the energy affected by chemical flocculents. Therefore magnetic flocculation can be used to agglomerate particles having surfaces ionized with like charges and only a minute quantity of ferromagnetic material will be necessary to develop sufficient force to overcome the repulsive ionic forces and hold together relatively large masses of fine solid agglomerates suspended in fluids. Since flocculation occurs after the fine suspension passes through a magnetic field generated by magnets surrounding a pipe section, the simplicity of the process and economic advantage makes magnetic flocculation very attractive.

Jan 1, 1971

By Wilbur A. Haley

One of the purposes of the investigation was to determine and report on how coal augers are used to mine bituminous coal that is near outcrops and may not be mined otherwise by any other present-day method. Such increased overall recovery results in the conservation of coal resources. Other reasons for the investigation were to determine and report the production rates of such operations and the types of equipment used. Auger mining of coal as a means of coal recovery supplementary to strip mining has been introduced and developed since World War II. This type of coal mining has grown rapidly, and bituminous-coal production by auger mining has been estimated at 6,000,000 tons in 1955. Mines were selected for study to give reasonably representative information on auger mining in different types and thicknesses of coal beds in different geographic areas and on different types and sizes of equipment operated under various conditions. This report is based on field studies of 8 auger-miming operations in Pennsylvania, West Virginia, and Ohio and in 5 different coal beds. Operations were observed in active strip mines, in strip mines reopened for auger mining, and along benched coal-bed outcrops. At the time of this study, no augers were reported to be operating in underground mines. The diameters of holes drilled ranged from 26 to 52 inches, and the lengths of holes ranged up to 208 feet. At some operations auger holes often penetrated abandoned underground mine workings.

Jan 1, 1957

By Leslie Gertsch

Outline First progress report ? ?Introduction ?Non-terrestrial mining ?Near-term targets ?Stages of mining ?Study procedure Capabilities needed for non-terrestrial mining ?Mining methods ?Mining unit operations ?Typical surface mine operations sequence ?Results to date General effects of gravity ?On fragmentation ?On excavation ?On transport ?Conclusions / Recommendations

May 1, 2013

By Joseph M. Singer

This research project had two main objectives: (1) To identify the smoke limits of gaseous fuel-air mixtures and (2) to obtain and evaluate basic chemical information on the formation of smoke in very rich flames near the smoke limit. Such information would do much to establish the circumstances for car-bon deposition in gas appliances and in other types of combustors. Based on tests with ethylene and propane, these studies showed the following: 1. Smoke limits are related to the yellow-tip limits of the fuel. Previous research established sufficient data to permit prediction of yellow-tip limits on gas burners using a wide variety of fuels. The present study of smoke limits deals only with ethylene-air flames, but the concept that was developed is probably applicable to other fuels.

Jan 1, 1962

By Nan C. Jensen

Modern high-temperature metallurgical processes have created a demand for raw material for furnace parts and lining that not only will with-stand high temperatures is but will not react with the substance being melted in the furnace. Spark-plug insulators, laboratory ware, tanks for the glassmaking making industry, and saggers and kiln furniture for the chinaware and pottery trades also must be made of materials hat have high melting points. Among the minerals that can be employed for such refractory uses ore those commonly known as the "sillimanite group' -kyanite, andaluste, sillimanite, and dumortierite - and the allied minerals topaz and pinite. Consideration of the occurrence, properties, qualities, uses, and sources of supply of these commodities and the markets for them constitute the subject of this paper. General Features of Kyanite and Related Minerals Kyanite, andalusite, and sillimanite ire composed of three elements - aluminum, silicon, and oxygen ? and are called aluminum silicates. The have

Jan 1, 1943

By Y. Ye

Typically, rougher molybdenite flotation and recovery from bulk copper/ molybdenum concentrates involves the use of alkalisulfides, Nokes reagents, cyanides, oxidants, and/or thermal treatment for the depression of copper sulfide minerals. The bulk copper/molybdenum feed generally varies from 0.2% Mo to 1.0% Mo, and with traditional reagents the single-stage rougher flotation recovery of molybdenite varies between 40 and 90% at a concentrate grade of 5 to 10% Mo. With ozone conditioning for copper depression, however, improved separations appear to be possible, as demonstrated by tests with Cu/Me concentrates from both the Phelps Dodge Morenci Operations and the Kennecott Copperton Operations. Single-stage rougher flotation after ozone conditioning can provide a molybdenum concentrate at a recovery of more than 90% and a rougher concentrate grade higher than 20% Mo in some cases. Subsequent cleaner flotation with additional ozone conditioning results in relatively copper-free molybdenum concentrates containing as much as 52% Mo. Preliminary analysis indicates that, with a multistage ozone conditioning/flotation strategy, the process is technically and economically viable and should be suitable for industrial application.

Jan 1, 1990

WHY IS IT that smoke-abatement efforts do not bring more satisfactory results? The main reason is an incorrect estimate of the kind and size of the job. When an industrial community realizes that keeping the air clean is a project of similar magnitude to keeping streets clean, providing clean water, removing city waste, or guarding the moral atmosphere, then there maybe a real hope of success. We usually think of the project in too small terms. It is thought of as is the dog catcher or the boiler inspector--a matter of a man or two, a job or two, a small appropriation of variable and uncertain amount, to be abolished in a fit of economy and reestablished under pressure of a vigorous minority. Even so, it is surprising how much is obtained for the effort; but the community is rarely satisfied, for the job is bigger than it was conceived to be. Continuous, never-ceasing effort is required to clean up a smoky city. A few months of relaxation and the situation slips back some years of effort.

Jan 1, 1938

By Kenneth M. Maas

The Bureau of Mines inventoried the land in southwestern Alaska to classify ownership and availability and compared this land with known mineral terranes and mineral deposits. This report discusses and quantifies the potential for favorable location of mining claims for metalliferous (locatable) mineral deposits. Of the nearly 24 million acres that constitute the study area, approximately 3.6 million acres or 17% are available for mineral location, 3.4 million acres or 14% are available with restrictions, and 17 million acres or 71% are unavailable. Mineral terranes are known to underlie about 7.8 million acres or 33% of the study area; 3 million acres or 38% occur on land available for mineral location, 1.3 million acres or 17% occur on land available with restrictions, and 3.5 million acres or 45% occur on unavailable land. The State of Alaska has opened over 91 % of its land in the study area to mineral location; in comparison, the Federal Government allows mineral location on 0.07% of the land under its jurisdiction. There are 117 known mineral deposits or occurrences within the study area, including 77 lode deposits and 40 placer deposits. Of the 41 lode deposits occurring within a mineral terrane, 2 occur on available land.

Jan 1, 1988

By H. Miller

In recognition of the need for a portable low-profile hard rock crusher, the Bureau of Mines sponsored the development of such a unit capable of moving up as the face advances. By allowing primary ore reduction at or near the mine face, the advantages of conveyor haulage From the face as demonstrated in soft ore and coal mines, could be realized for hard rock Brines as well. This report presents the results of a development and testing program for such a portable low-profile crusher, designed by Eagle Crusher Company and called the M44. The unit has an extremely low vertical profile considering its size and capacity. The crushing jaws, which form the crushing lumber, are inclined, with the lower jaw mounted for eccentric movement relative to the stationary upper jaw. This provides efficient crushing while also forcing material through the crushing chamber. As a result, the inlet feeder can be disposed horizontally. To facilitate correct processing of different materials, the size of the discharge opening and the action of the movable crushing jaw are variable. The unit also incorporates a feeder hopper and discharge conveyor that provides for efficient ore handling through the machine. Tests demonstrated the M44 Crusher's high capacity, efficiency and reliability. During testing, it crushed over 120,000 tons of materials of up to 32,000 psi compressive strength at production rates in the 200-350 tons/hour range. The unit operated smoothly under simulated low-headroom conditions, and Proved readily transportable.

Jan 1, 1983

By Adam J. Gesing

The eddy current separator (ECS) is designed to separate nonmagnetic (nonferrous) electrically conducting (metallic) particles from nonconductive residue. Nonferrous metallic particles are repelled out of the material stream passing over the eddy current rotor (ECR). The rotor is housed in a fiberglass composite outer shell that serves as a conveyor head pulley. This results in the desired metaVnonmeta1 separation. The behavior of ferromagnetic particles, mainly iron and iron oxide (i.e. rust), is quite different. These particles are strongly attracted to the magnets and the smaller particles tend to align their long axis in the direction of the magnetic flux. Since the direction of the flux changes with the passage of each magnet pole, the small particles spin at very high rates causing wear of the belt and of the composite outer shell housing the ECR. Large particles, when trapped under the ECS belt, cannot spin, but can be heated by the eddy current effects and subsequently can burn through the composite outer shell. We discuss the practical implication of this behavior of iron and rust on the design, performance and maintenance of eddy current separators.

Jan 1, 1999

By J. R. D. Gravel, D. A. Poland

"The induration of iron ore pellets has always utilized prefired pellets to protect the pallet cars from the environment of the induration furnace. This paper presents the process used to obtain superior upper sidewalls. These heat resistant castings are used on induration pallet cars, and their life improvements by as much as 400% is a significant step towards the reduction of the prefired (or hearth layer pellets.) The benefit to the industry in the removal of the hearth layer is improved overall productivity. IntroductionThe Iron Ore Company of Canada (IOC) operates with production facilities located in Labrador City, Newfoundland and Sept Iles, Quebec. It has recently been acquired by North Limited, an Australian based resource oriented company. Prior to its acquisition, IOC has examined several methods of operational cost reductions. One of these was an examination of indurrating pallets. Pallets are composed of numerous assemblies and sub-assemblies. The examination of the upper sidewalls began as an intent to increase the operational life of the component. The anticipated net effect was to be a reduction in the overall pallet maintenance cost. All of the components and assemblies have undergone a severe scrutiny. IOC has found that the success of the project has depended upon not only the technical competency of all parties involved, but also upon the ability to share risk, to be innovative, and to find a partner with whom the development can proceed without fear and yet with accountability. IOC has found in Cast Steel Products (CSP) such a partner in the field of pallet development. This paper will undertake to explore the progression into the arena of partnering between IOC and CSP. CSP and IOC met in the fall of 1994. The work of re-engineering the pallets began with an initial order for 36 pallets in March, 1995. The work on the upper sidewalls involved segregation of the effect of alloy development versus physical geometry development. The nature of partnering between the two companies allocated alloy development to IOC and physical geometry development to CSP, yet no advancements were made in either area without the close co-operation or the involvement of both partners."

Jan 1, 1999

By Alan M. Bateman

Before World War II we proudly considered that we were the nation of all the world most richly endowed in mineral resources. We knew it was no accident that those countries abundantly supplied with mineral resources became the great manufacturing nations, and the politically and militarily strong ones; and that our own great industrial cities sprang up where coal and iron met. We all reallized, especially we of the mining profession, that the energy of fuels and the solidity of metals spelled industrial growth and in turn industrial might and that other nations came to regard mineral self-sufficiency as one of the chief goalsof economic nationalism.

Jan 1, 1949