Search Documents

By Joseph Pogue

IN 1920, 531 million barrels of crude petroleum were consumed in the United States. As imposing as this figure is, the fact that the domestic consumption of crude petroleum has increased at an average rate of 10 per cent. a year for the past decade is more striking. Will this rate of increase in demand continue? If so, the year 1930 will call for 1260 million barrels of petroleum-a staggering volume. On the other hand, may we expect the demand for petroleum to grow as rapidly as it did when the automotive industry was having its most phenomenal expansion? If not, to what extent will the growth of oil requirements decrease? When and to what degree will the petroleum industry become affected by the economic law of diminishing returns? Obviously, this matter requires careful analysis, especially as both national and industrial planning must be predicated upon present estimates of the requirements of the future. The purpose of this paper, accordingly, is to project, as closely as present limitations of knowledge permit, the course of the demand for petroleum in the United States over the next ten years. At first, the problem of estimating the future of a demand as complex as that for petroleum might appear insoluble. Fortunately, however, there are several scientific methods of approaching the problem, centering around a study of rates of industrial growth, which lend considerable hope that the requirements of the immediate future in this field may be approximated with sufficient closeness to have practical value as a basis of action.

Jan 3, 1922

By Howard N. Eavenson

WHEN the A.I.M.E. was formed 75 years ago the bituminous coal industry was in its swaddling clothes, although it had been operating for more than a century and coal was being mined in every state now producing it, and its output had long passed that of anthracite. In 18/1, the value of bituminous coal was about seventy per cent of the value of all metals produced and more than one fifth of the value of all products of mines, both metallic and nonmetallic.[1a] While many of the operating mines then shipped by rail, most of the development was along waterways, although the canal era of transportation was nearly at its end. Coal mining is a heavy industry and one of the best measures of its progress is its output throughout the period. Fig. 1 shows this graphically from 1800 to 1945. From 1870 to 1910, the production-which is very nearly the consumption-almost doubled every decade, a most amazing growth. In 1918, in World War I, a peak was reached and a decline began, which ended in 1932. A gradual recovery then started, interrupted in 1938 but culminating in the record output of 1944, when, owing to World War II, a tonnage of 619,576,000 was produced. It is evident that the forces leading to the continuous increase ending in 1918 have spent themselves and that only unusual conditions will require so large a production again. The postwar conditions of World War II will probably

Jan 1, 1947

By Masayuki Otagawa

THE mining methods adopted in Japanese mines are less known to the mining world than those of other countries, owing to the geographical remoteness, but they present many features of interest to mining engineers. The Ashio copper mine is at the village of Ashio, in Tochigiken, about 109 mi. (175 km.) from Tokyo by the Imperial Government railroad. The area of the concession owned by the Furukawa Mining Co. is 5000 acres (5023 ha.). The mine was formerly divided into three, viz.. Honzan, Kotaki, and Tsudo, which are distant 3 mi. (4.8 km.) from each other as shown in Fig. 1. However, in 1914, when the writer was general manager, the three mining plants were amalgamated into one with the result of simplifying the working projects and increasing the operat-ing efficiency. The mine was visited-by the Institute party in November, 1911, when Mr. K. Inouye was the general manager. Shortly afterward, the writer was appointed manager, and, in 1915, he was succeeded by Dr. K. Asano. At the end of 1917, Mr. K. Kibe became general manager and, after two years, was succeeded by the present manager, Mr. I. Sugimoto-. For some time Dr. J. Kojima was acting general manager. It is needless to say that the gentlemen mentioned are all members of the Institute, as is also Baron T. Furukawa, president of the company. Since the discovery of the enormous masses, called "kajika" or "bullhead" deposits; which the writer has described elsewhere,' the mining methods have been varied to meet the different conditions presented by these deposits.

Jan 2, 1922

By Al Campoli

The majority of the 100 million roof bolts installed each year in the United States are 5/8 inch deformed rebar fully grouted into a one inch borehole. Commonly referred to as B-Series or No. 5 bar, this system is proven effective and cost efficient in coal mines with average to above average roof conditions. One of the critical variables affecting resin bolt performance is the size of the resin annulus, calculated as the difference between the hole and bolt diameters. The optimum annulus has been proven to be '/4 inch, which provides for effective mixing of the two polyester resin components and incorporation of the plastic film packaging within the cured resin. Glove fingering occurs when the plastic film is forced against the borehole wall potentially interfering with the mechanical interlock of the resin and the rock mass. Glove fingering is not a problem with the optimum '/n inch annulus but has been know to occur with the B-Series 3/8 inch annulus. Laboratory testing correlated the degree of Glove fingering with resin formulation and the bolt head to shaft axes alignment. Glove fingering occurred over 45 % of the grouted length of standard B¬Series bolts. The newly formulated Eclipse B-Series resin when combined with a 1/8 inch offset between the bolt head and shaft axes reduced the glove fingering 70%. The Eclipse system allows the 3/8 inch B-Series annulus to achieve the positive mixing characteristics associated with the / inch optimal annulus systems.

Jan 1, 2002

By Harry L. McNeill

The Selective Media Process was developed by the author in a laboratory provided by The Steams-Roger Manufacturing Co. It is the outcome of an investigation into the possibilities of coarse beneficiation by sink and float without using the conventional heavy media. Commercial work to date has been limited to the treatment of minus 3/8-in. iron ore at the Hill Trumbull washing plant of the Cleveland Clifis Iron Co., at Calumet, Minnesota. Two cut away prints of the machine are shown (Figs. I and 2). A rotary conical impeller is mounted within a stationary cone (Fig. 2). This impeller is adjustable vertically by a 12-ton screw jack. The speed of the impeller can be varied from 14 to 32 r.p.m. by the Reeves variable-speed motor pulley mounted on the 7½-hp. motor drive. Attached to the bottom of the stationary cone is the automatic control valve for sink product, actuated by a ¼-hp. gear motor. The sink product is dewatered in a conventional drag driven by a 7½-hp. motor and discharged onto an inclined conveyor containing from 6 to 10 per cent moisture. Two plants are operated at the Hill Trumbull property. All the ore is first treated in a typical washing plant (Fig. 3). when treating "wash ore" a finished concentrate can be produced by the log washers and Akins classifiers, as the separation involves only fine silica (minus 48-mesh) and free iron. However, when "jig ore" is led to the washing plant the coarse

Jan 1, 1947

By Harry L. McNeill

The Selective Media Process was developed by the author in a laboratory provided by The Steams-Roger Manufacturing Co. It is the outcome of an investigation into the possibilities of coarse beneficiation by sink and float without using the conventional heavy media. Commercial work to date has been limited to the treatment of minus 3/8-in. iron ore at the Hill Trumbull washing plant of the Cleveland Clifis Iron Co., at Calumet, Minnesota. Two cut away prints of the machine are shown (Figs. I and 2). A rotary conical impeller is mounted within a stationary cone (Fig. 2). This impeller is adjustable vertically by a 12-ton screw jack. The speed of the impeller can be varied from 14 to 32 r.p.m. by the Reeves variable-speed motor pulley mounted on the 7½-hp. motor drive. Attached to the bottom of the stationary cone is the automatic control valve for sink product, actuated by a ¼-hp. gear motor. The sink product is dewatered in a conventional drag driven by a 7½-hp. motor and discharged onto an inclined conveyor containing from 6 to 10 per cent moisture. Two plants are operated at the Hill Trumbull property. All the ore is first treated in a typical washing plant (Fig. 3). when treating "wash ore" a finished concentrate can be produced by the log washers and Akins classifiers, as the separation involves only fine silica (minus 48-mesh) and free iron. However, when "jig ore" is led to the washing plant the coarse

Jan 1, 1947

By H. M. Howe

(New York: Meeting, October, 1913.) 1. INTRODUCTION.-This paper gives the results of our micro-graphic determinations of the position of Ae3 in a series of 14 hypo-eutectoid steels of varying carbon content, one of them very rich in phosphorus, and of SEe for one hyper-eutectoid steel. We have pro-ceeded chiefly by noting the temperature -at which the reabsorption of the pro-eutectoid element is found to be complete after a 30-min. holding, but in part also by noting the temperature at which its precipitation begins. Observations on these same steels by Messrs. Burgess, Crowe, and Rawdon, of the United States Bureau of Standards, are given in a paper' issued simultaneously with this, while in a third paper s one of us compares these data with those of earlier observers. These three papers are treated as one whole by numbering their sections, tables, and illustrations continuously, and by setting the folding plates of micrographs at the end of the last paper. THE COMPOSITION OF THE STEELS EXPERIMENTED ON is given in Table I. Notation. and Definitions.-Following Osmond's development of Tschernoff's notation; in which " Ac3 " is the upper limit of the hypo-eutectoid part of the transformation range as observed in heating up, and " Ar3 " is that same limit as observed in cooling down, and following the usual custom of calling the upper limit of the hyper-eutectoid part of that range "SE," we may go farther and call this latter limit " SEc " when observed in heating up .and " SEr " when observed in cooling down.

Jan 6, 1913

By Harry L. McNeill

THE Selective Media Process was developed by the author in a laboratory provided by The Steårns-Roger Manufacturing Co. It is the outcome of an [ ] investigation into the possibilities of coarse beneficiation by sink and float without using the conventional heavy media. Commercial work to date has been limited to the treatment of minus 3/8-in. iron ore at the Hill Trumbull washing plant of the Cleveland Cliffs Iron Co., at Calumet, Minnesota. Two cut away prints of the machine are shown (Figs. I and 2). A rotary conical impeller is mounted within a stationary cone (Fig. 2). This impeller is adjustable vertically by a 12-ton screw jack. The speed of the impeller can be varied from 14 to 32 r.p.m. by the Reeves variable-speed motor pulley mounted on the 7 ½ -hp. motor drive. Attached to the bottom of the stationary cone is the automatic control valve for sink product, actuated by a ¼ -hp. gear motor. The sink product is dewatered in a conventional drag driven by a 7 ½ -hp. motor and discharged onto an inclined conveyor containing from 6 to 10 per cent moisture. Two plants are operated at the Hill Trumbull property. All the ore is first treated in a typical washing plant (Fig. 3). When treating "wash ore" a finished concentrate can be produced by the log washers and Akins classifiers, as the separation involves only fine silica (minus 48-mesh) and free iron. However, when "jig ore" is fed to the washing plant the coarse

Jan 1, 1946

By G. St. J. Perrot, S. P. Kinney

Consumers of metallurgical coke are agreed that the quality of their fuel plays an important part in the performance of the furnace. Less unanimous agreement is evident when the properties of a desirable coke are discussed or when consideration is made of suitable testing methods by which the worth of a coke for metallurgical purposes may be determined quantitatively. Much has been written of the importance of combustibility as a factor in determining the performance of coke in the blast furnace and it is generally believed that cokes vary widely in this respect. The usual operating data of the furnace afford little evidence as to the combustibility of the fuel. As a part of a general investigation of the properties of metallurgical coke, the Bureau of Mines has explored the hearth combustion zone in a number of blast furnaces by means of water-cooled gas sampling tubes driven into the hearth through the tuyeres. The attempt has been made to determine the difference in combustibility of cokes varying widely in physical properties. Data have also been obtained in an experimental combustion furnace at the Bureau laboratories in Pittsburgh. This paper gives the results of experiments, made at eleven blast furnaces, in which the composition of the gases was determined at various points in the hearth in the plane of the tuyeres. Further work is in progress in which the zone above the tuyeres will be explored. Factors Affecting Coke Combustibility Brassertl has defined combustibility as the rate of progression of combustion, or, in other words, the speed at which the carbon molecules

Jan 1, 1923

By S. A Weigand, J. W. Bolton

Production of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical. Review of Literature Carpenter and Edwards1 state that when gun metal is melted the alloy dissolves gas, the amount increasing with rise in temperature and duration of the melting. The solubility of the gas diminishes during the fall in temperature and it escapes through the liquid metal. At the moment of incipient solidification there is an evolution of gas. Sperry2 says that by using charcoal a reducing atmosphere is supplied whereby oxidation is prevented, and this also prevents gases from coming in contact with the metal. Logan3 says that many of the troubles that occur in non-ferrous castings are the direct result of one thing—oxidized material. He mentions how readily copper absorbs oxygen when molten, but does not mention the harmful effects of reducing conditions as observed in overpoled copper. Guillemin and Delachana14 investigated the gases occluded in bronze and found that the better bronzes contained mostly hydrogen while the poorer ones had a larger proportion of carbon monoxide and carbon dioxide.

Jan 1, 1929

By S. P. Kinney, G. St. J. Perrot

Consumers of metallurgical coke are agreed that the quality of their fuel plays an important part in the performance of the furnace. Less unanimous agreement is evident when the properties of a desirable coke are discussed or when consideration is made of suitable testing methods by which the worth of a coke for metallurgical purposes may be determined quantitatively. Much has been written of the importance of combustibility as a factor in determining the performance of coke in the blast furnace and it is generally believed that cokes vary widely in this respect. The usual operating data of the furnace afford little evidence as to the combustibility of the fuel. As a part of a general investigation of the properties of metallurgical coke, the Bureau of Mines has explored the hearth combustion zone in a number of blast furnaces by means of water-cooled gas sampling tubes driven into the hearth through the tuyeres. The attempt has been made to determine the difference in combustibility of cokes varying widely in physical properties. Data have also been obtained in an experimental combustion furnace at the Bureau laboratories in Pittsburgh. This paper gives the results of experiments, made at eleven blast furnaces, in which the composition of the gases was determined at various points in the hearth in the plane of the tuyeres. Further work is in progress in which the zone above the tuyeres will be explored. Factors Affecting Coke Combustibility Brassertl has defined combustibility as the rate of progression of combustion, or, in other words, the speed at which the carbon molecules

Jan 1, 1923

By Alden Greninger

TWINNED metal crystals are usually designated as either deformation twins or annealing twins. If twins are to be classified according to the treatment the metal has undergone just prior to the obser vation of the twins, there are two other possible groups: (1) solidification twins,? when observed in the as-solidified or as-cast condition, and (2) transformation twins, ? when observed in a metal which has been cooled from above an allotropic transformation temperature. McKeehan has demonstrated that ferrite does, occasionally at least, contain twinned structures2. The twins, which he studied by optical methods, were obtained during the preparation of iron single crystals by very slow cooling through A3. He proved that the twin relation was actually that which previous investigators had predicted; namely, twinning along three planes of the form {112}. Since McKeehan's discovery, little or no attention has-been given to this transformation twinning of alpha iron, or to the possibility that it might occur at all speeds of cooling from above A3 instead of merely during the prepara-tion of single crystals. McKeehan's twins were evidently regarded as interesting only in proving that a body-centered cubic metal could form twinned structures-at least under certain conditions. It is generally believed that iron seldom if ever forms annealing twins. Certainly the straight-line banding which is so abundant in annealed face-centered cubic metals is characteristically absent in iron annealed below A3. However, O'Neill3. has studied "twin-like" crystals in annealed alpha iron and concludes that the specimen he studied actually

Jan 1, 1936

By P. D. Duever, P. J. Readyhough, P. L. Silveston

"The Plastojrost apparatus, developed by Ritter and Juranek in the 1960s has been modified primarily, to automatic temperature control. A limited investigation of carboniferous and cretaceous coal samples showed that both coals undergo the same changes when coked in the Plastofrost unit. Dilatometer plastic range and total dilatation correlated well with the Piastofrost plastic range for the carboniferous Appalachian coal, but not for the cretaceous western Canadian coal. Work to elucidate the characteristics of some western Canadian coals using the Plastofrost is in progress. IntroductionCoke quality is critically affected by the properties of the plastic phase in the coal-to-coke transformation. Since these properties exist in a coke oven and are not measurable, they are approximated by standard laboratory tests, such as free swelling index, plastometry, and dilatometry. Of particular interest to us is the anomalous behaviour of western Canadian coals of cretaceous origin. By many predictive methods, these coals should not produce coherent cokes. When coked in pilot scale test ovens, in fact, they produce cokes of good stability. They typically make up 20% of Japanese coking coal blends and are also used in South Korea, Mexico, Brazil, and several European countries. This anomalous behaviour has been studied in our laboratory<8.9.1O). Plastic properties or rheological tests examine just the external ramifications of the coal-to-coke transformation. To understand the process, however, microscopic examination of the coal and coke seems to be needed. The Plastofrost unit has been shown to be a convenient means to this end."

Jan 1, 1987

By D. Reddish

The combination of free standing steel supports, such as arches, and rock bolts (mixed support) has Frequently been in used in UK coal mine roadways when it is considered that the strata and/or environmental conditions would not be suitable for rock bolts solely. However, how such mixed support systems operate is not fully understood. Due to the differences in the support method provided by rock bolts and free standing steel, the total support generated is not simply a case of adding the contribution to the support of the roadway given by the two systems. This paper describes a numerical investigation into mixed support systems when used in coal mine roadways. A series of 2D and 3D geomechanical models are described and the method of modelling the rock bolts and steel supports in coal mine tunnels is discussed. The numerical models described include rock boltd only roadways, steel supported roadways and mixed supported roadways in a variety of geological and in-situ stress conditions. Conclusions are formed that allow an insight into mechanisms of strata reinforcement provided by the support systems modelled. Further to this, a review of the numerical modelling of pre-tensioned rock bolted systems is described identifying the contribution to support efficiency given by the adoption of tensioning in full column resin anchors. The results obtained highlight that the effectiveness of the pre-tensioned load is dependant on the rock mass quality and in- situ stress level at the site where it is to be used.

Jan 1, 2004

By R. Spring

"Soft-sensors are a computer software alternative to inadequate hardware instrumentation. Filters are averaging methods that reduce the noise in any sensor&apos;s signal. This paper introduces these topics and places them in a mineral processing context using then-product formula.Soft SensorsAs their name implies, ""soft-sensors"" are computer programs that estimate values for process variables (Tham, 1991). This approach is useful when the appropriate hardware sensor does not exist, is deficient, supplies only infrequent values, etc. For example, in mineral concentrators the traditional magnetic flowmeter/ nuclear density gauge instrumentation for measuring slurry flows costs $5,000 or more per flow and requires frequent maintenance. However, metal assays are commonly available from online X-ray fluorescence analyzers and application of the n-product formula (Taggart, 1945) to these assays conveniently provides software estimates of the flowrates (albeit only when the circuit is in steady-state).Soft-sensors are used by inferential controllers that base their control actions on the process values ""inferred"" by the soft-sensor. Such was the case at Brenda Mines where the rod mill feed tonnage controller used an inferred value of the cyclone overflow particle size (Bradburn, 1976). It was also the case at Brunswick Mining where reagent controllers adjusted reagent addition rates throughout the plant according to the various ore flowrates inferred by an expert system (Spring, 1991). A unique feature of the expert system soft-sensor was its dynamic flow models which compensated for residence times, material transport lags, etc. Thus the soft-sensor values were valid under both steady-state and nonsteady- state conditions."

Jan 1, 1992

By J. W. Bolton, S. A. Weigand

Production of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical. Review of Literature Carpenter and Edwards1 state that when gun metal is melted the alloy dissolves gas, the amount increasing with rise in temperature and duration of the melting. The solubility of the gas diminishes during the fall in temperature and it escapes through the liquid metal. At the moment of incipient solidification there is an evolution of gas. Sperry2 says that by using charcoal a reducing atmosphere is supplied whereby oxidation is prevented, and this also prevents gases from coming in contact with the metal. Logan3 says that many of the troubles that occur in non-ferrous castings are the direct result of one thing—oxidized material. He mentions how readily copper absorbs oxygen when molten, but does not mention the harmful effects of reducing conditions as observed in overpoled copper. Guillemin and Delachana14 investigated the gases occluded in bronze and found that the better bronzes contained mostly hydrogen while the poorer ones had a larger proportion of carbon monoxide and carbon dioxide.

Jan 1, 1929

By E. A. H. Tays, F. A. Schiertz

In 1893 the Anglo-Mexican Mining Company, Limited, purchased the Guadalupe and adjoining mines, and, after opening up the Guadalupe, constructed a 20-stamp mill, which was started in August, 1894. Although the results were extremely profitable (the ore being very rich and carrying much free gold) they were not satisfactory, because the tailings were found to average about $20 per ton in gold. Early in 1895 the late Mr. James E. Mills made for the company a very thorough study of the subject, and decided that the tailings could be treated most advantageously by the cyanide process. In view of this opinion, Mr. Henry R. Batcheller, of Boston, was sent down in the winter of 1895-96 to experiment on a working scale. Mr. Batcheller was successful; and, during 1896-97, built a cyanide-plant with a capacity for treating 1500 tons per month. This was run until May, 1899, when all the sands suitable for the process had been treated. The mill was stopped about the same time for lack of ore; but no tailings from the mill had gone to the dump since October, 1897, as the values they contained after that date were far too low to warrant further treatment. When the cyanide-plant was stopped there still remained on the dump about 16,000 tons of slimes, consisting of about 75 per cent. of clay-slimes and 25 of sand-slimes. The successful treatment of this very unfavorable material is the theme of this paper. Fig. 1 is a view of the hacienda, taken in 1897.

Jan 1, 1902

By S Hughes

The smelting of concentrates and secondary materials has been subject to increasing challenges in recent years due to declining grades of feed materials, increasing impurity levels and ever more stringent environmental regulations. In addition there has been a growing focus on maximising the efficiency of energy usage and recovery of values. New opportunities have been created with rising metals prices and improved systems for the collection of secondary materials, giving rise to a need for more flexible process solutions.This paper focuses on a number of specific cases where a process solution has been developed using the Outotec« Ausmelt Process to meet particular feed material challenges and overcome limitations inherent when employing traditional pyrometallurgical processes.The first case involves the development and commercial implementation of a smelting process to recover values from zinc smelting residues typically deposited into dams as a waste product. The second case describes the application of the Ausmelt process for the smelting and converting of secondary copper feed materials, including e-waste. These materials contain a wide range of metals and plastics and need to be processed appropriately to maximise the recovery of values whilst avoiding environmental problems. The third case study covers the smelting of nickel concentrates containing elevated magnesia levels as well as nickel bearing catalysts with high alumina content, neither of which can be readily processed when employing traditional pyrometallurgical technologies. CITATION:Hughes, S, 2013. Pyrometallurgical process solutions for complex raw materials, in Proceedings MetPlant 2013 , pp 519-530 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By R. E. Morgan, Barkleym J. F.

"INTRODUCTION Wood burned for commercial heat and power usually is waste material from some manufacturing process. The amount of it reaches substantial proportions. It is estimated that over 50 percent of the timber cut for lumber becomes ""waste"" in the process - sawdust, shavings, trimmings, slabs, and bark. Woodworking manufacturing processes also produce much waste. The incentive to use this waste has resulted in much development of wood-burning equipment to produce heat and power. To answer general inquiries received by the Bureau, this publication covering developments along these lines was written. There is included a bibliography of additional information on the subject.COMPOSITION AND BURNING CHARACTERISTICS OF WOODThe approximate composition of moisture-free wood is, in even figures:PercentHydrogen 6Carbon 49Oxygen 44Ash 1Total 100This composition corresponds to about C6H1005. Moisture is essentially always associated with wood. Green wood contains approximately 30 to 50 percent moisture; air-dried or seasoned wood contains 15 to 25 percent and kiln-dried about 8 percent. Exposed to the weather, wood absorbs and gives off moisture depending on weather conditions and water contact.""Dry"" wood ignites relatively quickly and readily gives off volatile matter when heated. Long flames and smoke easily occur during burning. The burning action is substantially retarded, however, by appreciable moisture content; ignition is more difficult. When the moisture content is more than about 70 percent, an auxiliary fuel is required to maintain combustion. One of the main factors in the problem of the satisfactory and smokeless combustion of wood is its moisture content."

Sep 1, 1950

By S. B. King

IT is the purpose of this article to give those not familiar with the subject an idea of the extent to which coal is mined by machine in the United States; to describe some types of electrically operated coal cutters; and in particular, some of the latest improvements and developments in these machines. Generally speaking, the article deals with the mining of bituminous coal in room-and-pillar mines, as the use of undercutting machines in the anthracite region of Pennsylvania is in its infancy, and when machine mining is referred to bituminous coal is taken for granted. The number of mines in the United States that are operating on the long-wall principle is very limited, and the number of long-wall machines in use is a very small percentage of the total. The advantages of mining by machine may be summed up briefly as follows: A. Increased safety to property and life, due to the large decrease in the amount of powder required when the coal is properly undermined. B. Reduction in the cost of mining. C. Improvement in the quality of the product; and, consequently, increase in market value, due to the greater proportion of lump and screen sizes secured by machine mining. D. Increase in the capacity of the mine, and more rapid development of new mines. E. Ability to mine veins in which the height of the coal or the character of the roof has prevented mining by hand, on a commercial basis.

Jan 6, 1914