Search Documents

By R. D. Fisher, A. G. Metcalfe, F. A. Crossley

AN investigation of the application of magnetic stirring to the consumable arc melting of aluminum and nickel demonstrated that grain refinement could be obtained when there was sufficient stirring force. Also, it was found that grain refinement could be obtained in aluminum by alternately reversing the polarity of the current through the magnetic stirring coil. The effect of the latter was to periodically reverse the direction of rotation of the molten metal.' Because of their promise, these findings were applied to conventionally cast aluminum. Shortly after this work was begun, Kondic2 reported experiments in which aluminum cast with 40° C (72° F) of superheat exhibited a grain size of 10 to 20 grains per cm2. When interrupted rotation was applied during solidification by mechanical means, a grain size of 800 to 1000 grains per cm2 was obtained. Magnetic Stirring Applied to Conventional Casting— The applicability of magnetic stirring to producing grain refinement in conventionally cast metal was evaluated in the following way. Three pounds of aluminum were cast into a clay-bonded graphite mold. The mold was surrounded by a magnetic stirring coil of 1000 turns. A direct current of 200 amp was passed through the casting by means of a graphite electrode which was immersed from the top. A current of 5 amp was passed through the stirring coil. The aluminum (1100 or 25) was superheated to 1600° F (871° C) and fluxed by passing chlorine gas through the melt for 2 min prior to casting. Two additional castings were made for comparison: 1) a conventional casting of metal superheated to 1600° F and 2) a similar casting through which 200-amp current was passed during solidification, but without current in the magnetic coil. Macrosections of these three ingots are shown in Fig. 1. Very remarkable grain refinement resulted in the magnetically stirred casting. It may be noted that the casting through which 200-amp current was passed has a coarser structure than the conventional casting. It would appear that this is due to the additional heat input generated by the current to the former casting. Mechanical Rotation Applied to Conventional Casting—A casting temperature of 1600° F was used throughout. Some 1 1/2 -lb castings rotated at 150 rpm were predominantly columnar with small areas of coarse, equiaxed grains close to the lower mold wall. Following these, a series of 3-lb castings was made. Macrosections of these ingots are shown in Fig. 2. The imposed rotational speed was 250 rpm. Turbulence or acceleration in the solidifying liquid was the significant factor. Fine grain size resulted in the material solidified during the period of acceleration of the liquid to the imposed rotational speed. When uniform rotational motion was achieved, the grain structure reverted to columnar. The final casting shown in the lower right-

Jan 1, 1962

By R. A. Pallanch

Probably one of the most perplexing problems with which a mill operator contends is the proper evaluation of his mill results. True, he accurately determines his recoveries of metals and grades of products monthly, weekly, and often daily. These figures do not of themselves directly translate to mill economics. When one figure is unusually good there may be an offsetting circumstance. The advantage of high lead or zinc concentrate grade may be offset by poorer recovery; high lead recovery may be offset by poorer zinc recovery, or vice versa; and so on. Besides, grades or recoveries may not of themselves mean more than a reflection of the grade and character of the ore during the period under study. What the operator sorely needs is some one measuring stick that tells him when he has achieved his greatest return, regardless of grades or recoveries—for if he knows his methods and practices are yielding the optimum return he need no longer concern himself with the assays of products and tailings, or the corresponding distribution of metal values. At first blush it would appear that the obvious answer to this is the actual money return to the mill. Paradoxical as it may seem, however, money return does not make a dependable yardstick any more than do grades and recoveries, as ore condi- tions would vary enough to bring about greater money return during periods when the actual metallurgical work is not as good. The mill operator, of course, should always aim for the greatest return on the ore, once it is in the mill bins, with proper attention always to mill treatment cost. The need of a proper yardstick becomes more imperative with the increasing complexity of the problem. In the case of a simple, single-product operation on a fairly uniform ore, in which only one metal is of significant importance, the need is not great, as grade and recovery pretty well tell their own story. At the other extreme is the operation that makes three or four separate marketable products from a complex mixture of heterogeneous ores that vary tremendously in individual metal contents and ratios, degree of oxidation, and other characteristics, and in which gold, silver, copper, lead and zinc are all significant values. Economic Recovery The first attempt at obtaining a proper single yardstick for a fairly complex ore with which I am familiar is the use of the ''Economic Recovery" term at the lead-zinc flotation mill of the Sunnyside Mining and Milling Co., Eureka, Colorado. This method had been applied there early in Sunnyside flotation-mill history (not later than 1920) and credit for the innovation I believe belongs to Messrs. Kuryla and Marquand. The term "Economic Re-

Jan 1, 1949

By V. S. Tuman

In the first part of this paper, an estimate is made of the magnitude and extent of the thermal stresses which result from mud circulation. Our study is made for the period of relaxation, i.e., when the drilling operations are terminated and mud circulation is discontinued. In the second part, we have shown how the thermal stress can affect the wave propagation. An example is worked out for a Carbondale sandstone (Illinois basin). It is concluded that, in extreme cases when differential temperature is about 100°F, the travel time will be affected by about 2 microsec/ft. For more refined permeability studies, such corrections would be desirable. MAGNITUDE AND EXTENT OF THERMAL STRESSES RESULTING FROM MUD CIRCULATION When geological beds are penetrated by boreholes, it is observed that the formation temperatures increase with depth; however, the temperature profile varies considerably from place to place. During drilling operations, mud pumped from a pit at atmospheric temperature absorbs heat from the lower beds. As a result, the drilling fluid returning to the surface is at a higher temperature than the surrounding beds. The temperature gradient in a well depends on the rate of mud circulation and other factors; normally, this temperature gradient is smaller than the natural gradient in the formations. (See Fig. 1.) The temperature difference between the mud column and the surrounding beds gives rise to therma1 stresses (which are also important in the phenomenon of fracturing), and it is expected that they will affect the transit time of the sonic front in velocity logging.1 It is evident chat beds near the surface will undergo various cycles and will have a complicated dynamical and thermal-stress history. A limestone bed which is just penetrated will act as a source of heat, warming up the cold mud pumped down a few minutes earlier from the surface pit. The same limestone bed a week later will act as a sink, absorbing heat from the drilling mud which has already warmed up sufficiently to be at a higher temperature than the bed in question. No doubt a large section of the hole will undergo a heat treatment, which will make the calculation of the exact magnitude of the thermal stresses very difficult. In the solution of wellbore thermal equation, it is assumed that the rock around the wellbore is elastic and isotropic, and that the system is radially symmetrical. A complete dynamical solution of the thermal stresses set up at different horizons during the drilling operations would require a comprehensive history of the mud circulation, the surface temperature of the pit and the number of hours in which mud was not circulated. CONDUCTION OF HEAT AND THERMAL EQUATION OF STATE

By Fred T. Agthe, Fred C. Bond

When some materials are ground dry in a ball mill, a stage of comminution is reached at which the finely divided particles begin to adhere to the balls and to the mill lining. As grinding progresses, a coating accumulates upon the grinding media, which tends to cushion the impacts and thus retard reduction of the material. and finally becomes so thick that all grinding ceases. At this stage, the characteristic noise produced by the grinding media during normal mill operation changes to a dull, muffled sound. In most instances, the formation of the coating marks the practical limit of size reduction. Industrial requirements for fine grinding frequently meet with this obstacle, and the tendency in many commercial operations to grind materials to a higher degree of fineness than formerly makes the solution of this problem an important one. The phenomenon is of far greater importance, therefore, than the limited amount of research and technical discussion devoted to it implies. In order to learn more about the coating of different materials when ground dry to a high degree of fineness, certain laboratory tests were made from which it was found that different materials form coatings at widely different size distributions. It is probable that most materials will coat if they are ground fine enough; the exceptions have inherent lubricating qualities, like coal and graphite. In general, the softer materials tend to coat at coarser sizes than the harder or more brittle materials. Limestone, as an example, will coat more readily than quartz, even though limestones of different- texture and composition exhibit great differences in coating potentialities. Various materials were tested in the laboratory to show the variation in coating qualities. It was found that in most tests quartz must be ground to a fineness that would permit it to pass through 325 mesh before coating became markedly detrimental to the grinding operation. Siliceous rocks, however, tend to coat more readily than quartz. Granite, which is composed essentially of feldspar, quartz and mica, has been found to start coating at about 92 per cent through 200 mesh, and feld-spathic minerals alone usually show a tendency to coat at the same fineness. Barite has been ground in the laboratory to a fineness of 99 per cent through 325 mesh without showing serious coating of the grinding media. Gypsum coats readily. Apatite and phosphate rock usually tend to coat. Hematite usually coats, although when mixed with charcoal it does not do so. In testing the carbonate rocks and minerals, it has been found that burned magnesite, dolomite, and dolomitic limestone coat, whereas calcite and calcined calcite do not coat so readily. It has been found that commercial glass, slate, talc, steatite and coke have little tendency to coat. The relative tendencies toward coating during grinding operations, exemplified by

Jan 1, 1943

By Herbert A. Stein, John B. Murdock

AN analysis of perlite expansion furnaces must be based upon one consistent theory which explains how and why perlite does expand when heated. There is more than one such theory, so to establish a basis for the rest of this paper, the authors will outline one theory and the data that support it before going into the construction details of different furnaces. JOHN B. MURDOCK, Associate Member AIME, is President, and HERBERT A. STEIN is Secretary, of the Perlite Corp., Phoenix, Arizona. San Francisco Meeting, February 1949. TP 2736 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 3, 1949. Why Perlite Expands: Perlite is known to contain some dissolved or combined fluid, probably water, which is lost when the material is heated to fusion. It is generally agreed that when particles of this volcanic glass are heated to fusion in such a way that vaporization of this water into steam takes place at the same time as the glass becomes soft, the steam puffs up each particle into a mass of glass foam. It is a simple matter to expand perlite under a blow torch for demonstration purposes, but in commercial installations, the problem is made more complicated by the necessity of making efficient use of both raw material and fuel, and producing an expanded aggregate conforming to close specifications for size distribution and density, using many different types of perlite rock. The ability of a given operation to fulfill these requirements depends upon the proper handling of four variables. They are: (1) the nature of the perlite rock used, (2) the heating time taken to get the perlite particle up to its highest temperature, (3) the size of the particle, and (4) the maximum temperature the particle reaches. Types of Perlite Rock: Perlite may be classified in many ways, but the characteristics most easily correlated with its behavior in furnaces are its softening temperature, its effective water content, and its "liveliness." Actually there is a close correlation among these three characteristics so it is possible to describe a perlite using any one of them. Lively perlites always have low softening temperatures and high effective water contents, whereas the deader perlites have higher softening temperatures and lower effective water contents. These softening temperatures run from 1400°F to above 2000°F and the effective water contents run from over 2 pct down to 0.2 pct. Included in the category of lively glasses are the green pitchstone from the Edgar claim in Superior, Ariz., the red pitchstone on the Animas highway south of Lordsburg, N. Mex., and a gray glass from Beatty, Nevada. Examples of intermediate perlites (in order of decreasing liveliness) are the Guzman-Lobb perlite with obsidian

Jan 1, 1951

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By H. E. Hostetter

Grossmann's method1 for calculating the hardenability of steel from the composition and grain size has gained wide acceptance, and when properly used, has been well proved in practical application, both for estimating the hardenability of known compositions and for selecting compositions to meet known hardenability requirements. The Grossmann method uses as the criterion of hardenadility the "ideal critical diameter," DI, which is the' size round that will just harden to a structure of 50 per cent martensite at the center when given the theoretically fastest quench, or "ideal quench." The DI can be related to actual quenching practice if the severity of quench is known; or the DI can be correlated with hardenability as determined by the Jominy end-quench method.2 The effect on hardenability of each element present in a steel can be represented by a multiplying factor, the value of which depends on the amount of the element present and the degree of effectiveness of the particular element. (The value of the factor for a given carbon content varies with the grain size.) When the factors for all elements present in a steel have been determined from charts, they are multiplied, and the resultant product is the DI of the steel. The validity of Grossmann's scheme of multiplying factors has been confirmed in a number of other investigations.3-6 It can be appreciated that a certain desired level of hardenability can be obtained by adding chromium, molybdenum, nickel and vanadium to a base composition containing carbon, manganese, silicon and the usual impurities. Many of the ranges of hardenability used commercially can be obtained by any of the foregoing alloying elements used singly in the base composition. The same hardenability levels also can be obtained through use of any of a great number of multiple element combinations of these alloying elements. In this report a method will be presented for determining what one combination is the most efficient (based on hardenability and cost of added alloy) for a given level of hardenability. It should not be assumed from the emphasis given to hardenability, that hardenability is the only criterion for the selection of an alloy composition. Such properties as the hot-working characteristics, machinability, carburizing characteristics, amount of distortion during quenching and the retention of austenite may be considerations of importance in many applications. However, hardenability is one of the most important properties of an alloy steel and one that must be considered in almost all cases involving heat-treatment by quenching. Therefore, a method for determining the lowest-cost alloy combination should be of considerable value. Determination of Most Efficient Combinations For comparing the alloying elements on standards of cost and hardenability, it

Jan 1, 1947

By J. D. Milburn, H. J. Hill

In quantitative interpretation of electrical logs the presence of clay minerals introduces an additional variable which further complicates an already complex problern. Although recognizing the difficulties introduced as a result of the heterogeneity of natural sediments and despite the present incomplete state of knowledge regarding electrochemical behavior of shales, dissemirzated clay minerals and concentrated electrolytes, it was felt that useful empirical correlations might be obtained from experimental investigation. Six typical sandstone formations, having a wide variety of petrophysical properties, were selected for the study. Approximately 45 samples from each formation were selected to satisfactorily represent the range of pore size distribution within the particular formation, As a matter of general interest, four limestone formations were also included in the investigation. Previously proposed equations relating to resistivity, SP and interrelationship of the two phenomena have, where possible, been tested with data obtained in this investigation. These equations do not satisfactorily describe experimental behavior of samples through all degrees of shaliness or throughout the range of brine solution resistivities normally encountered in logging practice. An empirical equation has been developed which quantitatively relates formation resistivity factor to satirrnting solution resistivity, porosity, and "effective clay content." This relation is indicated to be uniformly applicable to clean or shaly reservoir rocks. It is shown that both the SP and resistivity phenomena of shaly samples are related to the sample cation exchange capacity per unit pore volume. The independent chemical determination of this parameter is thus a means of determining the "effective clay content" of samples. Some implications regarding theory and electric log interpretation of shaly sands are discussed. INTRODUCTION The use of electrical resistivity logs as a means for estimating formation porosity is based upon the original work of Archie1. It was shown by empirical methods that the resistivity of a rock, when 100 per cent saturated with brine solution, could be related to rock porosity through the equation, F = Ro/ RW = f-m.......(1) where F, the formation resistivity factor, is defined as the ratio of the resistivity of the 100 per cent water saturated rock, Ro, to the saturating solution resistivity, Rw; f is the ratio of pore volume to bulk volume; and m is the slope of the average line when the data are plotted on log-log paper. This relation was established for relatively shale-free formations containing water having high salt concentrations, and under these conditions F may be considered constant for a given rock sample. Applications of Eq. 1 to interpretation of logs of shale-free formations has been quite successful when satisfactory formation water resistivity data could be obtained. The most readily available means of estimating formation water resistivity is the self-potential log. Conventional methods of SP log interpretation involve correct.

Jan 1, 1957

By B. M. Larsen, T. E. Brower

IN an earlier paper1 we discussed a simple, rapid method of taking samples of liquid steel and analyzing them for oxygen, which, though possibly not absolutely accurate (as is likewise true of all other methods), certainly yields results that are satisfactorily consistent. Accordingly, samples from hundreds of heats in different shops were analyzed for oxygen, with results sufficient in number to be handled statistically and permit estimation of some general trends. Measurements were made in acid as well as in basic open hearths, throughout the refining period, to learn how stirring, blocking, adding ore or lime or sand, affects the oxygen content of the bath; we also followed the changes brought about by tapping, teeming, and deoxidizing. Some of these results, discussed in an earlier paper.2 bring out the dominant role of the carbon-oxygen reaction in regulating degree of oxidation both of metal and of slag, also the marked variability of concentration of dissolved oxygen [0] in excess of that which would be in equilibrium with carbon and with carbon monoxide at a partial pressure of one atmosphere. As a logical beginning on this complex problem, we take up in the present paper the variability of this excess oxygen, ?[O], when other factors are as constant as they ever are in open-hearth operation; namely, toward the end of the refining period, when the bath may be regarded as in the comparatively steady state it approaches in absence of disturbing factors. This condition was chosen because by that time the significant reactions, except carbon oxidation, between slag and metal have come to substantial equilibrium; this facilitates interpretation of the complex situation and thus permits more definite conclusions to be drawn. This excess concentration of oxygen, ?[0], in the metal is needed, of course, to make the steelmaking process go at a reasonable rate; alternatively it may be regarded as a measure of the virtual pressure increment above one atmosphere, or of the degree of supersaturation, of carbon monoxide in the metal. According to our measurements, the excess concentration ?[O] in liquid steel varies from about 0.009 to 0.035 per cent oxygen by weight. It is quite sensitive to change of conditions, being altered temporarily by operations such as stirring with green poles, additions of ore, lime, or sand; but as the disturbance works itself out, it resumes a level within the intermediate range characteristic of the steady state. The conditions most common in average furnace practice are covered by the following : [ ] as in a reasonably steady state-that is, when it is boiling normally, is at proper temperature with a well-shaped slag, and has been free from disturbing effects during the preceding half hour-?[O] returns from

Jan 1, 1946

By H. E. Hostetter

Grossmann's method1 for calculating the hardenability of steel from the composition and grain size has gained wide acceptance, and when properly used, has been well proved in practical application, both for estimating the hardenability of known compositions and for selecting compositions to meet known hardenability requirements. The Grossmann method uses as the criterion of hardenadility the "ideal critical diameter," DI, which is the' size round that will just harden to a structure of 50 per cent martensite at the center when given the theoretically fastest quench, or "ideal quench." The DI can be related to actual quenching practice if the severity of quench is known; or the DI can be correlated with hardenability as determined by the Jominy end-quench method.2 The effect on hardenability of each element present in a steel can be represented by a multiplying factor, the value of which depends on the amount of the element present and the degree of effectiveness of the particular element. (The value of the factor for a given carbon content varies with the grain size.) When the factors for all elements present in a steel have been determined from charts, they are multiplied, and the resultant product is the DI of the steel. The validity of Grossmann's scheme of multiplying factors has been confirmed in a number of other investigations.3-6 It can be appreciated that a certain desired level of hardenability can be obtained by adding chromium, molybdenum, nickel and vanadium to a base composition containing carbon, manganese, silicon and the usual impurities. Many of the ranges of hardenability used commercially can be obtained by any of the foregoing alloying elements used singly in the base composition. The same hardenability levels also can be obtained through use of any of a great number of multiple element combinations of these alloying elements. In this report a method will be presented for determining what one combination is the most efficient (based on hardenability and cost of added alloy) for a given level of hardenability. It should not be assumed from the emphasis given to hardenability, that hardenability is the only criterion for the selection of an alloy composition. Such properties as the hot-working characteristics, machinability, carburizing characteristics, amount of distortion during quenching and the retention of austenite may be considerations of importance in many applications. However, hardenability is one of the most important properties of an alloy steel and one that must be considered in almost all cases involving heat-treatment by quenching. Therefore, a method for determining the lowest-cost alloy combination should be of considerable value. Determination of Most Efficient Combinations For comparing the alloying elements on standards of cost and hardenability, it

Jan 1, 1947

By William B. Stephenson

IN the pumping of sands, slurries and slimes, practices developed over the years are the real keystones of successful operation. These practices are necessarily based on modifications of familiar theories. Practical methods used in the solution of problems involving the pumping of materials are set forth in the following discussion. BASIC REQUIREMENTS To pump sands and slurries economically, a few basic requirements must be met by the pumping system as a whole. A pipe-line velocity must be established that will move the fluid mixture throughout the entire system without any possibility of the solids settling out. To accomplish this, the velocity of flow must be slightly in excess of the critical velocity of the mixture. The critical velocity of a mixture varies from 3 ft. per sec. to 18 ft. per sec., depending on the screen analysis, concentration, and specific gravity of the solids in the mixture. Most tailings are pumped at a minimum velocity of 4 ft. per sec. if they include slimes, whereas the pipe lines of sand and gravel dredges require velocities as high as 18 ft. per second. A number of articles have been written on the determination of the minimum velocities required to maintain solids in suspension. Studies have also been made on the friction and pumping heads developed when handling solids in suspension.1-4 Our experience so far has shown that, within the normal operating limits of a pumping system, the friction factor follows more nearly the basis described by Howard,1 who says, among his conclusions: " ... values of ƒ (friction factor) .. . will decrease with an increase in velocity." This conclusion is borne out by our actual experience. When the velocity in a pipe line is not sufficient to keep the solids in suspension, the total friction head is greater than when the velocity is increased to a point where the solids are in suspension. A slight increase in the volume of feed to the pump and a slight increase in the pump speed are usually all that is necessary to put the system in balance. MAINTAINING CONSTANT VOLUME Within reasonable limits, the volume of mixture to be handled through a pipe line should be held constant, so that the required velocity will be provided at all times. There are several ways in which this can be accomplished. The commonest is to provide a sump of sufficient capacity to take care of slight surges in the volume of mixture being fed to the pumping system. This sump, however, should not be as large as a settling chamber. The use of a float-controlled, fresh-water make-up valve in a sump will guarantee a constant volume. Where variations in volume are slight,

Jan 1, 1946

By Herbert A. Stein, John B. Murdock

AN analysis of perlite expansion furnaces must be based upon one consistent theory which explains how and why perlite does expand when heated. There is more than one such theory, so to establish a basis for the rest of this paper, the authors will outline one theory and the data that support it before going into the construction details of different furnaces. JOHN B. MURDOCK, Associate Member AIME, is President, and HERBERT A. STEIN is Secretary, of the Perlite Corp., Phoenix, Arizona. San Francisco Meeting, February 1949. TP 2736 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 3, 1949. Why Perlite Expands: Perlite is known to contain some dissolved or combined fluid, probably water, which is lost when the material is heated to fusion. It is generally agreed that when particles of this volcanic glass are heated to fusion in such a way that vaporization of this water into steam takes place at the same time as the glass becomes soft, the steam puffs up each particle into a mass of glass foam. It is a simple matter to expand perlite under a blow torch for demonstration purposes, but in commercial installations, the problem is made more complicated by the necessity of making efficient use of both raw material and fuel, and producing an expanded aggregate conforming to close specifications for size distribution and density, using many different types of perlite rock. The ability of a given operation to fulfill these requirements depends upon the proper handling of four variables. They are: (1) the nature of the perlite rock used, (2) the heating time taken to get the perlite particle up to its highest temperature, (3) the size of the particle, and (4) the maximum temperature the particle reaches. Types of Perlite Rock: Perlite may be classified in many ways, but the characteristics most easily correlated with its behavior in furnaces are its softening temperature, its effective water content, and its "liveliness." Actually there is a close correlation among these three characteristics so it is possible to describe a perlite using any one of them. Lively perlites always have low softening temperatures and high effective water contents, whereas the deader perlites have higher softening temperatures and lower effective water contents. These softening temperatures run from 1400°F to above 2000°F and the effective water contents run from over 2 pct down to 0.2 pct. Included in the category of lively glasses are the green pitchstone from the Edgar claim in Superior, Ariz., the red pitchstone on the Animas highway south of Lordsburg, N. Mex., and a gray glass from Beatty, Nevada. Examples of intermediate perlites (in order of decreasing liveliness) are the Guzman-Lobb perlite with obsidian

Jan 1, 1951

By E. A. Gulbransen, W. S. Wysong, K. Andrew

The reaction of carbon in solid solution in a metal with the surface oxide fim on many metals may be inferred from thermo-dynamic calculations for high vacua and high temperature conditions. Holm has recently shown that oxide films may be removed from ferrous materials by heating in a vacuum at high temperatures and that carbon is the essential element in the reaction. considerable work has been described in the literature on the de-carburization reaction. Several general references may been 2,3,4 However, the nature of the mechanism involved in the decarburization is not well understood. Our interest in this reaction resulted from many attempts to degas and to reduce by pure and dry hydrogen the surface oxides on strips of various types Of chrome-nickel alloys. Some of the early experiments On the behavior Of '3 pct chrome-iron in vacua of the order of 5 X lo' mm and at a temperature Of 600°C have been reported.5 These experi-merits showed a 'low reaction with the residual Oxygen Or water vapor in the system and no reaction with hydrogen. This is in accord with thermodynamic data which would lead to the prediction that it is extremely difficult to maintain a hydrogen atmosphere at 600' C pure enough to reduce Crz03 formed On the surface. The crystal structure of the superficial oxide film formed on 13 pct chrome- iron and Nichrome V has been investigated in the thin film range by Gulbransenr Phelps and Hickman,' and shown to be "203. It Was surprising to us to note that when a specimen of Nichrome V containing approximately 80 pet nicke1 and 20 pet chromium was heated to 850°C in a high vacuum, the specimen lost weight. The rate Of weight loss was very temperature sensitive. A study of this reaction in vacua and in a hydrogen atmosphere is the subject of this communication. Type Reactions Let us consider the various reactions which may occur when a metal is heated in vacua, in a hydrogen atmosphere, or in an oxygen atmosphere. The number and kind of reactions will depend upon the chemical nature of the metal, its alloying constituents and the location of the alloying constituents. The metals used in this study are chrome-nickel alloys of the heater type, They consist essentially of chromium, nickel and iron, small amounts of carbon, silicon and manganese and traces of zirconium, calcium, aluminum and magnesium. The trace elements are added to improve the lifetime and other characteristics of the alloy when used as a heater. Seven of the more important reactions with which we are going to be concerned here are as follows: 1. Metal . (gas) F? metal + gas — degassing of the metal 2. zM(s) + y }i Oi(g) M MIOu(s) -oxidation

Jan 1, 1949

By Palmer C. Sweet

Kyanite. andalusite, and sillimanite are anhydrous aluminum silicate minerals, and they have the same chemical formula, Al2SiO3. Dumortierite and topaz are also classified as aluminum silicates although they contain boron and fluorine respectively. Mullite (a rare mineral named for its discovery site, the Scottish island of Mull) is produced when kyanite, andalusite, or sillimanite are heated. Synthetic mullite, also classified as an aluminum silicate, is formed by melting alumina and silica, bauxite, and kaolin or alumina, kaolin, and kyanite, depending on the type of synthetic mullite desired. These materials are either sintered in rotary, periodic, or tunnel kilns, or fused in an electric arc furnace. The world's largest producer of kyanite is the United States. Domestic kyanite is presently produced from one company at two sites in Virginia; Kyanite Mining Corporation mines kyanite from Willis Mountain and adjacent East Ridge in Buckingham County in the central Piedmont province of Virginia. Internationally, kymite is produced in Australia, Brazil, India, Kenya, Sweden, and Zimbabwe; the former USSR also produces kyanite (Fig. 1). Andalusite is produced by Piedmont Minerals Company, Inc. in the Piedmont province near Hillsborough, NC. Andalusite is also produced in France, India, the Republic of South Africa, and Spain (Fig. 1). Sillimanite is produced in Australia, Brazil, India, Spain, and the Republic of South Africa; the former USSR is also thought to be a major producer (Fig. 1). Some of the countries produce only for domestic use. Synthetic mullite, made by sintering and by electric arc fusion, is produced by Mulcoa (Mullite Company of America) in Andersonville, GA, and by Washington Mills Electro Minerals Corporation in Niagara Falls, NY. Annual world production of kyanite, andalusite, sillimanite, and synthetic mullite is approximately 672 727 tons (Potter, 1988). GEOLOGY Mineralogy Kyanite is a blue to light-green, triclinic mineral that occurs in long, thin-bladed crystals and crystalline aggregates in gneiss, schist, and pegmatites. The mineral has a hardness of 5 parallel to the long axis of the crystal and a hardness of 7 across the crystal. Andalusite is a yellow, brown, green, or red orthorhombic mineral that occurs in thick, almost square prisms in schist, gneiss, and hornfels. Gem quality andalusite exhibits a strong pleochroism; brownish-green in one direction and brownish-red perpendicular to it. Andalusite also occurs in placer concentrations where it has weathered out of rock. Sillimanite is a brown, pale-green, gray, or white orthorhombic mineral that occurs in long, slender, needlelike crystals in schist and gneiss. Chemical and Physical Properties Chemical and physical properties of kyanite, andalusite, and sillimanite are noted in Table 1. Kyanite is the only mineral that irreversibly expands when heated (calcined to produce mullite) and may offset the shrinkage of most ceramic or refractory ingredients when heated.

Jan 1, 1994

By E. A. Gulbransen, W. S. Wysong, K. Andrew

INTRODUCTION THE reaction of carbon in solid solution in a metal with the surface oxide film on many metals may be inferred from thermodynamic calculations for high vacua and high temperature conditions. Holm1 has recently shown that oxide films may be removed from ferrous materials by heating in a vacuum at high temperatures and that carbon is the essential element in the reaction. Considerable work has been described in the literature on the decarburization reaction. Several general references may be noted.2,3,4 However, the nature of the mechanism involved in the decarburization is not well understood. Our interest in this reaction resulted from many attempts to degas and to reduce by pure and dry hydrogen the surface oxides 0n strips of various types of chrome-nickel alloys. Some of the early experiments on the behavior of 13 pct chrome-iron in vacua of the order of 5 X 106 mm and at a temperature of 600°C have been reported.5 These experiments showed a slow reaction with the residual oxygen or water vapor in the system and no reaction with hydrogen. This is in accord with thermodynamic data which would lead to the prediction that it is extremely difficult to maintain a hydrogen atmosphere at 600°C pure enough to reduce Cr203 formed on the surface. The crystal structure of the superficial oxide film formed on 13 pct chrome iron and Nichrome V has been investigated in the thin film range by Gulbransen, Phelps and Hickman,6 and shown to be Cr203. It was surprising to us to note that when a specimen of Nichrome V containing approximately 80 pct nickel and 20 pct chromium was heated to 850°C in a high vacuum, the specimen' lost weight. The rate of weight loss was very temperature sensitive. A study of this reaction in vacua and in a hydrogen atmosphere is the subject of this communication. TYPE REACTIONS Let us consider the various reactions which may occur when a metal is heated in vacua, in a hydrogen atmosphere, or in an oxygen atmosphere. The number and kind of reactions will depend upon the chemical nature, of the metal, its alloying constituents and the location of the alloying constituents. The metals used in this study are chrome-nickel alloys of the heater type. They consist essentially of chromium, nickel and iron, small amounts of carbon, silicon and manganese and traces of zirconium, calcium, aluminum and magnesium. The trace elements are added to improve the lifetime and other characteristics of the alloy when used as a heater. Seven of the more important reactions with which we are going to be concerned here are as follows: [I. Metal • (gas) ;--* metal + gas - degassing of the metal 2. xM(s) + y ½ 02(g) tom- M.0„ (s) – oxidation]

Jan 1, 1948

Discussion of the papers of FREDERICH LAIST and HAROLD W. ALDRICH, FREDERICH LAIST and F. F. FRICK, W. L. AUSTIN, and STUART CROASDALE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletins No. 91 and 92, July, and August, 1914. R. C. CANBY, Wallingford, Conn. (communication to the Secretary*). -Apropos of the experimental reduction of copper from cuprous chloride by fusion with ground limestone and coke, as described by Messrs. Laist and Frick, and also proposed for use at Chuquicamata., it might be of interest to refer briefly to the experience at Argentine, Kan., in the smelting of the suboxide of copper (as produced in the Hunt and Douglas process) containing appreciable quantities of chlorides. In the Engineering and Mining Journal of June 10, 1911, I. gave some account of what had appeared to be crucial difficulties with the Hunt and Douglas process, and how the filter-press difficulty had been so rapidly overcome after my discovery of the effect of the sodium salts in the leaching solutions. I also described the effect of the cupola furnace gases upon the lime rock with which I had replaced the coke in the absorption tower, which apparently showed the presence of considerable-chlorine, clue to the imperfect conversion of the subchloride to suboxide, as well as that clue to the difficulties of washing thoroughly the suboxide with the means provided, and also to the presence of chlorides in the cement copper which was smelted With the suboxide. The fumes from the cupola, when issuing direct into the atmosphere, were very dense and white, except when a hot furnace top caused a reddish tinge due to dust. These, fumes had a peculiarly suffocating effect, so that when they were blown over into the town the population suffered the greatest actual distress, not the mere annoyance which would have been clue to a disagreeable odor. The absorption tower had been built at the instance of the city authorities to abate this nuisance, and not with the idea of making any additional metal savings. A serious feature in connection with the Argentine experience with the Hunt and Douglas process was, that it had been implicitly assumed that there could be no metal loss in the Hunt and Douglas process itself, and that all attempts to locate the ruinous copper losses which were accumulating in the metallurgical accounts were devoted to the roasting department. It is possibly unfortunate for metallurgical advance along these particular lines that just about the time of this discovery of this previously unsuspected volatilization loss, in the smelting of the suboxide, the Kansas City company made a contract with the Western Union Telegraph Co. for its supply of copper sulphate and the Hunt and Douglas

Jan 11, 1914

By Fred C. Bond, Fred T. Agthe

When some materials are ground dry in a ball mill, a stage of comminution is reached at which the finely divided particles begin to adhere to the balls and to the mill lining. As grinding progresses, a coating accumulates upon the grinding media, which tends to cushion the impacts and thus retard reduction of the material. and finally becomes so thick that all grinding ceases. At this stage, the characteristic noise produced by the grinding media during normal mill operation changes to a dull, muffled sound. In most instances, the formation of the coating marks the practical limit of size reduction. Industrial requirements for fine grinding frequently meet with this obstacle, and the tendency in many commercial operations to grind materials to a higher degree of fineness than formerly makes the solution of this problem an important one. The phenomenon is of far greater importance, therefore, than the limited amount of research and technical discussion devoted to it implies. In order to learn more about the coating of different materials when ground dry to a high degree of fineness, certain laboratory tests were made from which it was found that different materials form coatings at widely different size distributions. It is probable that most materials will coat if they are ground fine enough; the exceptions have inherent lubricating qualities, like coal and graphite. In general, the softer materials tend to coat at coarser sizes than the harder or more brittle materials. Limestone, as an example, will coat more readily than quartz, even though limestones of different- texture and composition exhibit great differences in coating potentialities. Various materials were tested in the laboratory to show the variation in coating qualities. It was found that in most tests quartz must be ground to a fineness that would permit it to pass through 325 mesh before coating became markedly detrimental to the grinding operation. Siliceous rocks, however, tend to coat more readily than quartz. Granite, which is composed essentially of feldspar, quartz and mica, has been found to start coating at about 92 per cent through 200 mesh, and feld-spathic minerals alone usually show a tendency to coat at the same fineness. Barite has been ground in the laboratory to a fineness of 99 per cent through 325 mesh without showing serious coating of the grinding media. Gypsum coats readily. Apatite and phosphate rock usually tend to coat. Hematite usually coats, although when mixed with charcoal it does not do so. In testing the carbonate rocks and minerals, it has been found that burned magnesite, dolomite, and dolomitic limestone coat, whereas calcite and calcined calcite do not coat so readily. It has been found that commercial glass, slate, talc, steatite and coke have little tendency to coat. The relative tendencies toward coating during grinding operations, exemplified by

Jan 1, 1943

By Harold Vagtborg

Equilibrium vaporization ratios were obtained for light hydrocarbons, nitrogen, carbon dioxide, and hydrogen sulfide in a reservoir fluid containing 35 mole per cent hydrogen sulfide. The data cover the range from 700 to 2500 psia at 154°F. The results of this study are compared with results obtained by other investigators on systems containing less hydrogen sulfide. When large amounts of hydrogen sulfide are present, the equilibrium vaporization ratios for ethane and heavier hydrocarbons are greater than the ratios for systems containing little or no hydrogen sulfide. Large amounts of hydrogen sulfide have the reverse effect on the ratios for methane. Routine PVT studies were performed on the reservoir fluid including flash and differential liberations of the dissolved gas. The pressure-volume relationships of the saturated fluid were also determined. It is shown that the use of published correlations on physical properties of reservoir .fluids can lead to gross errors when applied to systems containing large amounts of hydrogen sulfide. INTRODUCTION Equilibrium vaporization ratios for various components in naturally occurring crude oil and condensate systems have been reported in the literature.1,2,3,4 Recently, several papers have been published with emphasis on non-hydrocarbon components such as nitro- gen, carbon dioxide and hydrogen sulfide.5,6,7,8,9 The increased discovery of reservoir fluids having high concentrations of these non-hydrocarbon components, particularly hydrogen sulfide, has created a need for a further study of their phase behavior. Equilibrium vaporization ratios are known to vary with pressure, temperature, and overall composition of the system.'" It was anticipated that ratios for systems containing large amounts of hydrogen sulfide would differ from the ratios for systems containing small amounts of hydrogen sulfide. Therefore, the present work was undertaken in order to obtain reliable equilibrium vaporization ratios for the reservoir-fluid in question. PROCEDURE The procedure followed was evolved after considerable experimentation on methods of handling the very sour crude. It was found that drying agents (e.g. CaCl2 and CaSO4) absorbed an appreciable amount of hydrogen sulfide from the gas used to prepare the recombined samples. The concentration of hydrogen sulfide dropped as much as 10 mole per cent in a single pass through a 3-ft drying tube. It was also found that when undried gas was agitated with mercury in the PVT cell, a black scum, believed to be mercuric sulfide, was formed and the hydrogen sulfide content of the gas dropped several mole per cent. Because composition changes during a run could not be tolerated, separation of the mercury and sour fluid was necessary. In order to effect this separation, a stainless steel piston, equipped with Teflon O-rings, was placed in the PVT cell between the mercury and the sour fluid. This piston had to be constructed in three parts because

Jan 1, 1955

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By C. S. Matthews, H. C. Lefkovits

The performance of depletion-type reservoirs at the stage in which the gas is at such low pressure that gravity is essentially the sole driving force has been investigated both theoretically and by use of scaled models. A simple theory is developed which completely explains the scaled model experiments. It also agrees with some field data. When the range of production rates to be considered is less than 25, the theory predicts that the production rate decline curve for homogeneous reservoirs in which there is a free surface will be of the hyperbolic type with n = 2: The theory gives a physical significance to the parameter y. INTRODUCTION This investigation was undertaken to determine a method for prediction of performance of reservoirs where gravity is the sole driving agent. Depletion-type reservoirs fall into this category after the pressure has fallen to some low value. Some examples of this type are found at Healdton ('Oklahoma), Oklahoma City (Oklahoma), Midway-Sunset (California), and East Coalinga (California). Generally the production rate per unit thickness is quite low in such reservoirs, with the conse- quence that this stage is sometimes called the stripper stage. However, per well production rates may be of the order of 50 B/D because of the considerable sand thickness open in some of the reservoirs. In the past, predictions of behavior of such reservoirs have been based on empirical extrapolation of the rate of production to the economic limit. Difficulties arise when new wells are drilled in the field or when production is artificially curtailed, since in such cases the decline rate of individual wells or leases changes and no clear trend can be detected. It was hoped that the present study would lead to improved methods for evaluation of such reservoirs. The study was initiated by building a scaled model for a particular field and by running a number of experiments on this model. Later a simple theory was developed which explained the laboratory results completely. The theory led, as shown below, to a hyperbolic-type decline equation which had been used previously' in a completely empirical manner. THEORY The General Case The problem to be treated here is the following: We are given a homogeneous cylindrical porous reservoir with exterior radius r, wellbore radius r., and height h,, containing, from the bottom up to a height hit oil, some gas, and interstitial water (see Fig. 1 A). The portion of the reservoir between K, and h, is filled with gas at low pressure, with residual oil, and with interstitial water. If at a time t = 0, the level of the oil in the wellbore is lowered to a height h,, what is the production rate from the reservoir at a time to The configuration within the reservoir at some instant

Jan 1, 1957