Search Documents

By AIME AIME

AN IMPORTANT innovation in Alabama in the semi-longwall type of coal mining as applied to low-dipping thin seams has been introduced by the Galloway Coal Co., mining the Mary Lee high-ash seam which averages only 26 in. thick. The property is their Mill Creek mine, near Carbon Hill, Ala., in the Warrior coal field. The results, although not final, indicate that roof conditions can be successfully handled by this method without loss of walls, with a rate of recovery much above that possible with the room-and-pillar method, and at the low production cost necessary for this grade of coal. Double cross-headings are turned off a main haulageway on 60-ft. centers and driven 40 ft. wide with thin chain pillars between. These double entries are turned at 525-ft. intervals, leaving a solid block of coal 440 ft. across; that is, from the outside of one pair of headings to the inside of the next pair is 440 ft. The bottom, which consists of hard fireclay, is taken in these entries 8 ft. wide and 4 ft. deep for head room.

Jan 1, 1934

By E. W. Engelmann

A NEW and interesting type of drier has been developed and operated at the Magna plant of the Utah Copper Co. for the past year for the drying of a filtered concentrate in the molybdenum recovery plant of this company. The several units installed have ranged from 12 to 30 in. in width, and from 14 to 30 ft. long. Their economy was immediately apparent after the first one was installed. The machine is not only low in capital cost, but has proved efficient for the drying of fine concentrate at low operating cost. The Utah vibrating drier consists of a steel conveyor trough supported on flexible reeds from a structural steel foundation anchored in concrete. The steel pan, which is also the drying surface, is vibrated by a heavy Utah electromagnetic vibrator fastened either to the head or discharge end of the pan. The vibration thus obtained agitates the material and causes it to be conveyed over the heated surface.

Jan 1, 1938

By Frank T. Sisco

The discovery of phosphorous is usually credited to the German alchemist Brand, in 1669, and the element was rediscovered the next year by Boyle in England. IT was more than 100 years later, however, before its presence was detected in high-carbon iron produced in early blast furnaces. In 1781 the German chemist Meyer published the results of his investigation on the ?white earth? that he had found in cast iron made from bog ores. This white earth was metallic in appearance, it was extremely brittle, it was readily fusible, and it was not attracted by magnet. Meyer noted that cast iron containing this white earth was more fusible than other cast iron, and he was sure that he had discovered a new metal ? for which he proposed the name Wassereisen, or the Latin term Hydrosiderum. Two years later the distinguished Swedish Chemist Bergmann made the same discovery, finding a ?white calx? in cast iron, which he also mistakenly considered to be a new metal, and for which he proposed the Siderum.

Jan 1, 1944

By R. D. Parker

LARGEST of any hoist installation ever manufactured in Canada is that being erected at No. 5 shaft, Creighton mine, of the Inter- national Nickel Company of Canada, Limited. It is a bicylindrical conical- drum hoist with the drums arranged in tandem, and driven by two direct- current motors through single reduction gearing. This hoist was designed by the Canadian Allis-Chalmers, Limited and manufactured at their works in Lachine, Quebec.

Jan 1, 1936

By J. E. Johnson

Discussion of the paper of Prof. Henry M. Howe, presented in abstract by Bradley Stoughton at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912, pp. 1181 to 1227. J. E. JOHNSON, JR., Ashland, Wis. :-This material is largely beyond the understanding of most of us practical men, but there are certain portions of that diagram that are of enormous importance. We have been conducting a, very extensive investigation of the quality of charcoal-iron and of all iron, and we have found that this eutectic point here (indicating on chart) is a sort of balance point between the good irons and the bad ones, and I have some slides to show what practical results we have found depending on this point here on the d diagram; and it would be a mistake for men who were -concerned with operation and were getting practical results, to think that these things are of no importance. They are exceedingly hard to understand, and I confess that a great deal of them is beyond me, but there is no doubt that the quality of iron depends to an enormous extent on the location of the carbon content of the iron to the right and left of this point, and the position of that point is dependent upon the silicon, and I wish to make a plea to the practical and operating members of the Institute not to disregard this material on account of its being highly scientific, because I hope to show later that there are matters of the highest practical importance that depend directly upon certain portions of this diagram. HENRY D. HIBBARD, Plainfield, N. J. :-T understand that washed metal, which, is practically pure iron and carbon, does not solidify at one instant, is cast-iron does, but passes through a mushy stage. That has been an enigma as to how and why it did so, and possibly some light might be thrown on it in this connection. BRADLEY STOUGHTON, New York, N. Y.:-If Wittorff's propositions are accepted, washed metal containing more than 4.1 per cent. of carbon would begin to solidify as liquid plus Fe4C

Dec 1, 1912

By Hugo L. Johnson, Robert Wallace

THE Midvale plant of the United States Smelting Refining and Mining Company consists of a flotation mill for concentrating sulphide ores of lead and zinc by differential flotation to produce three separate concentrates, one of lead, one of zinc, and one of iron pyrite; and a lead smelter for smelting ores and concentrates to produce base lead bullion, The plant, including its shops, laboratories, office, railroad yards which serve both mill and smelter, and areas reserved for tailing ponds and slag dumps, covers 646 acres on the right bank of the Jordan River at Midvale, Utah. It is twelve miles south of Salt Lake City and sixteen miles east of the West Mountain mining district at Bingham Canyon from which is drawn a large part of its ore supply. Custom ores are treated as well as the product of Company mines.

Jan 1, 1948

J. T. Pullon, Rowangarth, Roundhay, Leeds, England :— In discussing Mr. Lee's paper, I wish to call attention to the fact that Mr. B. II. Thwaite (who was heard here yesterday on the subject of the application of blast-furnace gas for the production of power, of which he was undoubtedly the pioneer) read, at the Engineering Congress in Glasgow in 1901, a paper on the profitable utilization of power from blast-furnace gases,' in which he suggested the diversion and cleaning of the whole of the waste gases coming from the blast-furnace and their utilization for power-production, so as to obtain, with proper manipulation, from 4 to 6 times the efficiency of present methods. He suggested also the heating of the stoves with producer-gas of a higher and therefore more suitable calorific value, so as to maintain them in a constant state of maximum efficiency, free from dust, and to avoid the irregular working of the furnace, besides obtaining a maximum supply of air-blast, of 15 or even 20 lb. pressure, by means of internal-conibustion blast-engines driven by the cleaned waste furnace-gases, with a surplus of gas left for other uses. Since that time, in view of the necessity of having a stand-by plant, immediately available, in case of strikes or other reasons causing the banking or blowing-out of the blast-furnace, he has developed, as an addition to his other types of producer, a high blast-pressure gas-generator, producing a gas identical with, or somewhat superior to, blast-furnace gas; and in which all the ash of the fuel is turned into fluid slag, which is available for, the production of slagwool. The gas is a little richer in carbon monoxide than average blast-furnace waste gas, and has only from 1 to 3 per cent. of hydrogen. Fig. I, drawn from a photograph, shows a plant containing this generator, now in operation at Leeds. It is made in units of from 1,000 to 10,000 h.p. capacity for each vessel, and coupled,

Jan 1, 1907

By W. W. Bristol

The Jerritt Canyon Joint Venture project is located approximately 50 miles (80 km) north of Elko. Nevada, U.S.A. and produces between 250 and 300 thousand ounces of gold annually. The Joint Venture is 70% owned by Independence Mining Company and 30% owned by Meridian Gold Company. Independence Mining Company is the operator. The Jerrin Canyon Joint Venture started operations in 1980 mining a series of open pit mines. Since the early 1990's, the discovery of deeper ores has required the joint venture to develop and mine a significant portion of its annual production utilizing underground mining methods. Underground production started with the West Generator Mine in 1993 followed by the Murray Mine in late 1994. Presently, two additional underground projects are being developed. Underground mining at Jerritt Canyon is budgeted to produce 128 thousand ounces in 1997. This paper documents the major transition/redevelopment of the Jerritt Canyon mining methods.

Jan 1, 1997

By G. M. Hughes

"400 cubic foot Agitair Flotation Cells are in use at Sherritt Gordon's Fox and Ruttan Mine Cu-Zn concentrators. The 4 impeller model No. 120, used at the Fox Mine Operation, appears to offer superior agitation and aeration qualities compared to the single impeller model 120A, in use at Ruttan. The advantages of the model 120 are most significant with ores of high specific gravity and coarse grind.IntroductionSherritt is using 400 cubic foot Agitair flotation machines at both the Fox and Ruttan Mine Concentrators.At the 3000 tpd, Cu-Zn Fox concentrator, 18 model 120 machines have been in operation since May, 1969.The 10000 tpd, Cu-Zn operation at Ruttan utilizes 49 model 120A machines. The plant started operation in May, 1973.The 4-impeller model 120 flotation cell has been marketed by Galigher since the early 1960's but the single impeller model 120A is relatively new.Model 120 Agitair -Cell DataThe Model 120 (Dwg. 1) has floor dimensions of 101 x 10' and a lip height of 2~ to 4 feet to provide up to 400 cubic feet of volume. This machine is shown with a froth crowder and stabilizer plates which are optional.Each motor drives two agitators. 20 HP is recommended by Galigher but 25 HP is more realistic with massive sulphides. The SG of ?ox ore is about 3. 6.The Model 120 can handle up to 600 cubic feet of air per cell at 2 psig which requires 5-6 HP at the blowers. Air volume to each impeller is controlled by a valve from a main header.During the first 3 years of operation at Fox there were few mechanical problems with the 120's."

Jan 1, 1974

T. M. Drown, South Bethlehem, Pa.: Mr. Thackray's paper shows in a striking way the high degree of rapidity and ac curacy exhibited by the chemists of our steel-works in ordinary everyday practice. That determinations made in an hour should present only slight differences in the third place of deci male is certainly matter for surprise and congratulation. This remarkable result has been due, perhaps, in part, to a remark able cause. The managers of works, ignorant of all the diffi culties of the laboratory, have demanded "the impossible " of their chemists—and the chemists have done it! Andrew A. Blair, Philadelphia, Pa.: Mr. Thackray's paper is extremely interesting, especially in its bearing on the question of a standard method for the rapid determination of phosphorus in the laboratories of steel-works. Before discussing the re sults in general, I desire to explain the results obtained by me under method A'. This is the method which I have used in the work of the sub-committee on Methods of the Interna tional Steel Standards Committee. It may be described briefly as follows: Solution in nitric acid; oxidation of carbonaceous matter by permanganate; precipitation of phosphoric acid by molybdate solution; reduction of molybdic acid in the reductor, and titra tion by permanganate. This method was used apparently by only three chemists, Dr. Dudley, Mr. Crowell, and myself. In determining phosphorus by this method, among the most essential points to be considered are the ratio of iron to molyb dic acid, or the reducing action of zinc on molybdic acid as compared to its reducing action on iron, and the ratio of molyb dic acid to phosphorus in the ammonium phospho-molybdate obtained by precipitation from the solution of the steel. In regard to the first point, the usually accepted ratio is 1 to 0.90756, or, as it is roughly stated, 0.9076, which is based on the assumed reduction of the molybdic acid to Mo12019,. This

Jan 1, 1896

By Lawrence A. Soltis

Senior engineering or executive management positions are filled by engineers who are evaluated on their performance, knowledge, skill, and maturity. Not only is technical expertise required but a knowledge of sales and marketing, finance, law, industrial relations, and public affairs is necessary. The University of Wisconsin-Extension offers an innovative post-baccalaureate degree program blending technical and professional subjects the Professional Development Degree in engineering (PDD)-designed to bring various opportunities for learn-

Jan 4, 1978

By B. D. Hansen

Newmont has been on a focused path of improving operations for many years. After the merger of Newmont and Santa Fe Pacific Gold, Newmont created significant synergies of over $50million per year in Nevada, primarily through optimal ore movements and consolidation of various functions. During the current period of low gold and copper prices, Newmont has refocused its efforts on efficient operations worldwide. This paper will describe the methods and programs that continue to be implemented at Newmont's many mine facilities in Nevada. Newmont has used a combination of computer technology, optimal use of infrastructures, procurement strategies, functional consolidation, enhanced mine planning and a variety of available metallurgical processing options to decrease the cost of operations and increase profitability.

Jan 1, 1999

By D. Kaja

The Symons Cone Crusher was invented by Edgar B. Symons in 1923. It was quickly accepted as a superior secondary and tertiary crusher. Nordberg manufactured crushers for the Symons Brothers Co. and in 1928 acquired the Symons Cone business. Since then, the Symons cone has become the standard of the Mining Industry. This is due to the basic rugged design and Nordberg's continued efforts to modernize and upgrade the crusher design over the years. In 1930, the Heavy Duty model was introduced with a 225 kW (300 HP) rating. Then in 1931 the Short Head version was developed to handle finer crushing applications. In 1950, the 7 Ft. XHD design was produced which provided higher crushing force capabilities for harder ores and for smaller product size requirements. Finally, in 1978, the 7 Ft Super Heavy Duty design was created to expand the power rating to 500 HP and to further increase the crushing force limits. The first 7 Ft. Super Heavy Duty crushers were delivered to Bougainville Copper Ltd. in 1978 for the production of primary ball mill feed in a three stage crushing plant with the third stage in closed circuit. The product size was 80% minus 6.35 mm (1/4 in).

Jan 1, 1998

Theo. B. ComstocK, Los Angeles, Cal. (communication to the Secretary*):—Mr. Blake's recent paper upon this topic undoubtedly partly explains the rationale of a part of the known facts bearing upon discolorat'ion and encrustation of rocks. His quotation from Humboldt, with reference to certain South American examples, may be questioned in the light of further facts, which do not appear to bear out the great traveler's theory of causation. There is no available evidence that the waters of the tropical rivers referred to by Professor Blake contain dissolved organic matter in the varying proportions required to demonstrate Humboldt's guess, nor do the concomitant facts in any manner bear out the hypothesis that the blackening in one case and its absence in the other may, perhaps, be traced to differences in the chemical reactions of the respective waters. Careful consideration of Professor Blake's illustrations, in connection with numerous personal observations extending over widely-scattered areas, convinces me that elements of

Jan 1, 1905

By CHARLES M. SCHWAB

THE ENGINEERS have placed this great country of ours in a preeminent position with everything pertaining to manufacture, metallurgy, and the kindred arts. We are second to none in the world. We have a country which, another speaker has said, God has endowed with such riches in coal and natural resources as no other country in the world. But rich as these are, there is one thing greater; the sturdy character, energy, and integrity of its people, which will make these great resources an influence in the world's developments. Great as are these resources and the energy and integrity of our people, there is one problem of our .engineering, which I term human engineering, that is of far more importance than the creation of machines and methods, with which you have been so successful in the past. Of what value is the skillfully devised machinery, the complex process, unless manned and operated by people whose heart and soul are in sympathy with the work they are doing and who have before them the giving of a complete day's work for a day's pay?

Jan 1, 1920

By B. D. Hansen

Newmont has been on a focused path of improving operations for many years. After the merger of Newmont and Santa Fe Pacific Gold, Newmont created significant synergies of over $50 million per year in Nevada, primarily through optimal ore movements and consolidation of various functions. During the current period of low gold and copper prices, Newmont has refocused its efforts on efficient operations worldwide. This paper will describe the methods and programs that continue to be implemented at Newmont's many mine facilities in Nevada. Newmont has used a combination of computer technology, optimal use of infrastructures, procurement strategies, functional consolidation, enhanced mine planning and a variety of available metallurgical processing options to decrease the cost of operations and increase profitability.

Jan 1, 1999

By D Lawie

Prior to resource modelling, sample scale data is normally grouped into spatial domains that reflect zones of homogenous properties. These domains are usually based on a combination of grade and other variables that reflect, for example, geology and alteration, or variables known to correlate with properties of the samples that affect downstream processing. Domaining and wire-framing sample scale data is a time intensive task and it is difficult to track more than a few variables simultaneously while establishing domain boundaries. This is especially the case in operations with complex data, for example, a combination of multi-element assaying of total element concentrations, and/or phase specific assaying such as sulfide sulfur, carbonate carbon, cyanide available gold, and/or downhole geophysical measurements. To minimise unintentionally grouping samples of contrasting properties within the same domain, unsupervised statistical methods are available that can automatically identify samples atypical of the domain, both as univariate tests, and as tests that take correlation within the domain into account. Unsupervised methods in this context means methods of identifying atypical samples that require just the selection of the domain and input variables. Thresholds are derived robustly from the data itself, and the results are therefore repeatable and operator independent. Atypical samples may be thought of as outliers, ie, samples that are separated from the ‘majority’ of the data. If these atypical samples are themselves spatially associated, they may be allocated to an alternative existing domain or allocated to a new domain. Care should always be taken to ensure that identified outliers are due to meaningful causes and not due to data coding and storage errors, although the identification of the latter is still valuable. *This is an abstract only. No paper was prepared for this abstract.*

Sep 5, 2011

By CHENCHEN SUN, GUOPING LUO, GUOCHENG ZHANG

In this study, the conditions of raw materials and fuels were simulated for Bayan Obo iron ore concentrate by adding pure calcium fluoride (CaF2) in various concentrations to Australian iron ore. The mechanism by which the fluorine (F) content of the lattice influenced the reduction swelling properties of the iron ore briquettes during various stages of the reduction process was investigated. The results provide insight into the mechanism governing the reduction swelling process in Bayan Obo ore briquettes, which could be used to direct real?world production practices, particularly those related to the rational utilization of Bayan Obo ore resources.

By Kenneth Williams

Economic drives dictate the exploitation of formerly less attractive ore bodies located close to or even beneath the water table. These ores can cause handling problems and expensive downtime of processing equipment due to their increased adhesive characteristics and are colloquially termed as “wet and sticky” ores. In order to gain a better understanding of the causes of poor handleability, experimental test methods for wall and inter-particle adhesion within bulk solids samples were developed and validated. The results confirmed that adhesion of bulk solid to equipment surfaces is mainly governed by capillary pressure. It can therefore be described using the Young-Laplace equation, which implies that adhesion is primarily dependent on the interfacial water between bulk material and the adhesion partner. Accordingly, the governing material parameters of adhesion are its capillarity and permeability, as these two characterize water transport to or from the interface of the adhesion partners. Furthermore a threshold for the classification of a material as wet and sticky based on the measurements of adhesion has been proposed.

Aug 17, 2017

By CASSANDRA L. HOEBBEL, PATRICK L. YORIO, Emily J. Haas

This study revealed significantly less favorable perceptions of the existing organizational safety climate among workers in the underground coal-mining sector compared with those in the industrial-minerals and sand, stone and gravel (SSG) sectors. Consequently, it is important to consider pragmatic ways in which health and safety management systems (HSMS) in coal mines can alter processes to improve these perceptions. Given the interdependencies of safety climate factors and HSMS elements, researchers explored mineworker perceptions of the supportiveness of organizational safety climate factors among mineworkers and identified significant differences in perceptions across sectors. In this paper, we suggest that health and safety professionals in underground coal mining and organizations with fewer resources or less mature HSMSs focus on these factors to bolster support for proactive safety performance. Potential barriers to implementing or improving relevant HSMS elements and ideas to help foster more favorable perceptions of organizational safety climate are also discussed.