Search Documents

By Haofeng Xie, Lijun Peng, Xujun Mi, Xue Feng, Xiangqian Yin, Zhen Yang, Guojie Huang

The Cu/Al composite wires have been widely used in cable industry. Especially in the development of aerospace, the light weight character of wires is particularly important. The wires are fabricated by a drawing process and heat treatment. Mechanical and electrical properties are measured and analyzed. The bending behavior is studied by scanning electron microscope. INTRODUCTION Cu/Al composite is a typical bimetallic composite that has been used in plenty of fields such as automobile and aerospace. The composite has the advantages of excellent conductivity as well as low weight, which cannot be obtained from single copper or aluminum. Industrial products of Cu/Al composite include Cu/Al composite joints (Uscinowicz, R., 2013), Cu/Al bimetallic sheets (Li, X. et al., 2011), Cu/Al flat bar (Wu, Y. & Liu, X. & Xie, J., 2014) and CCA wires (Ahmed N., 1978). CCA wires refer to the composite wires that copper layer concentrically coated on the surface of aluminum core conductor, implementing solid combination of two metals on the interface and forming an integral. At present, the aircraft cable generally use copper or copper alloy conductor, which makes the wire in the aircraft occupy a considerable proportion due to the large density of copper. Therefore, the use of Cu/Al composite wires instead of copper wires for weight loss, is of great significance to the development of aerospace technology industry. Heat treatment is an indispensable procedure to improve plasticity during cold working process, which is of great importance to preparation of wires (Wang, Q. et al., 2008). During the heat treatment, the Intermetallic Compounds (IMCs) are inevitable formed at the contact area of Cu/Al due to the occurrence of diffusion (Lee, S. et al., 2012). According to the results of former researchers, kinds of IMCs were discovered. Antoine Gueydan (2014) identified the formation of three IMCs (Al2Cu, AlCu, and Al4Cu9) at the interface between copper and aluminum after thermal aging. IMCs have a significant effect to the properties of Cu/Al wires. Bending performance is a vital property for the actual application of wires. The brittle IMCs may create a stress concentration that can cause crack initiation during bending process. This work focus on the mechanical properties of Cu/Al composite wires after heat treatment. The effect of various annealing condition on mechanical and electrical properties are studied, in order to find the appropriate annealing conditions, which produce optimal combination properties of Cu/Al clad composite wires. Bending fracture of composite wires is discussed by morphology observation.

Jan 1, 2019

By J. Keith Haddock

"IntroductionThe Bienfait Mine is operated by Bienfait Coal Company Ltd., one of the Luscar Limited group of companies. Situated 5 km southeast of the town of Bienfait, Saskatchewan, it can produce 2.0 million tonnes of lignite annually in addition to 158,000 tonnes of char from a carbonization plant located on the property. Geology The economically mineable coal seams of the Estevan area are found in the Ravenscrag Formation. The lignite-bearing sands, silts and clays were deposited in Early Tertiary age, in an inland sea centred in the Williston Basin of North Dakota. The top of the Ravenscrag is an erosional surface, overlain by Tertiary or Quarternary sands and gravels or glacial till. The regional structure is a gently plunging syncline which dips to the southeast at about 0.3 degrees. There are minor undulations in the Bienfait area which are due to differential subsidence during deposition. Sporadic faulting is probably a result of glacial pressures, and preglacial and glacial channels are responsible for washout zones and the abrupt irregular subcrop found in the area. There are two economic coal seams in the Bienfait area, an uppe; seam locally known as the Roche Percee, and a lower seam, the Estevan. Both seams have been extensively mined since lignite mining began in the area in the late 1800s. The Roche Percee remains only in a small portion of the Bienfait Mine and comprises a very minor portion of the reserves. It averages 1.74 m thick under 8.1 m of overburden. The till rests on top of the Roche Percee and due to weathering the seam is generally of poorer quality. The Estevan seam comprises the majority of reserves at Bienfait. The main seam which is being worked on consists of an upper bench averaging 2.75 m, a carbonaceous parting of 0.21 m, and a lower bench of 0.92 m. Overburden depth above this seam varies from 21.0 m to 38.0 m."

Jan 1, 1985

By Eugene W. Pearson

In a marked departure from conventional practice, the Power Plate process combines the two unit operations of leaching and electrowinning into a single continuous step for direct recovery of copper from sulfide concentrates, cement copper, copper scrap, and copper oxide slurries. Considering how environmental controls are pre- venting development of smelters for additional capacity or new construction, the Power Plate process provides a welcome pollution-free alternative to the smelting-electrorefining routes. And its low capital investment and low operating costs also recommend it to copper producers who are now using or investigating various hydrometallurgical methods.

Jan 12, 1974

By R Barritt

Remedial options for a waste rock dump (WRD) were considered as part of closure planning studies at an active mine in Western Australia. To minimise the impact of any seepage from the landform it was determined that placement cover system utilising the moisture ‘store-and-release’ concept was appropriate. The purpose of the cover system was to:•Reduce net infiltration of meteoric water to attenuate peak concentrations for contaminants of concern in natural receptors to levels that can be assimilated without adverse impact to the surrounding ecosystem; •Provide a growth medium for establishment of a sustainable vegetation canopy; and •Improve current quality of surface water runoff from waste storage areas.The project comprised several phases of work: materials characterisation, numerical soil-plant-atmosphere (SPA) modelling and finally cover system construction and monitoring equipment installation.CITATION:Barritt, R, 2018. Conclusions from long-term cover system performance monitoring – a case study, in Proceedings Life-of-Mine 2018, pp 101–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By J. Z. Keating

There are close to two million tons of Industrial Minerals processed and sold in North America wherein the processor/marketer has no affiliation with the source mine. The largest quantity, about 800,000 tons, is barium sulfate, which is sourced in lump ore form mainly from China and India. The Alumina Trihydrate Industry sources several hundred thousand tons from various alumina refineries. Substantial quantities of bauxite, zircon, magnesite, and fluorspar arrive in North American ports each month. There are also rapidly growing quantities of offshore talcs and calcium carbonate ores being processed in U.S. plants. These feedstocks are usually quite pure, have unique properties, and enjoy bulk rail or waterborne freight economies that allow successful competition with locally sourced raw materials. With increasing restrictions on mining activities, and the increasing need for sophisticated functional minerals, the importation of minerals will continue to grow.

Jan 1, 1994

By Z. Y. Xie

The visualization techniques were employed for the analysis of computer simulation studies of dislocation core structure in ordered alloys. Atomistic computer simulation was used for the study of the local configuration of the material in the vicinity of the dislocation. Stresses were applied in the simulation in order to study the necessary stress level for the dislocation to move and onset plastic deformation of the material. The results were analyzed in terms of the strain tensor as a function of the position (x, y) in the material with the dislocation located at (0, 0). Various visualization packages are used to plot the invariants of this strain tensor and to visualize the changes that the dislocation core undergoes under stresses until it finally moves.

Jan 1, 1993

By Thomas Varley

"Concentration, ore-dressing, or the dressing of minerals are common terms used in metallurgy and indicate processes of separating valuable minerals from worthless gangue. It is understood, of course, that the products from such processes, being separated from the various minerals and gangue, are ready for commercial sale or for further treatment by smelters and refineries.Gravity concentration takes advantage of the difference in specific gravity of the various constituent minerals and gangue of waste material in the ore. The two most common forms of concentration by this means are jigging and table concentration. Jigs usually are used in the separation of relatively coarse material and the tables for the finer material, the line of division in general being about 20 mesh.There are mar factors to be considered .before a decision can be made as to what method would be best adapted to the successful treatment of an ore and only by careful experiments can this be determined. Among the important factors to be considered are. The nature of the minerals present, their physical and chemical relations to the gangue material, and the gangue material itself. Perhaps the most important is the number of minerals present and their relation to each other.Metals exist in ores in three principal forms -- sulphides, oxides or carbonates, and native. Concentration by gravity methods is in general best suited to sulphide ores, although in some places considerable success has, been obtained in the concentration of oxide ores by gravity methods."

Apr 1, 1920

By Karel Rössler, Petr Vítek

"The Ejpovice tunnels in Czech Republic were built by EPBM in soft Clyashale, and in weathered profile with low soil overburden. The segmented liner at the cross-passage openings required support, which would not interfere with the EPBM clearance envelope during the scheduled pull back of the EPBM through both tunnel tubes. For that reason support frames or radial bolting could not be used. Steel rods inserted into the neighboring segments during the ring assembly, and later grouted were tested and realized as an innovative solution. The paper presents practical experience gained with the segmented liner support during cross-passages construction. INTRODUCTION An innovative solution using the grouted dowels was developed and realized for sixteen cross-passage openings of the twin Ejpovice Tunnels, whose construction was part of the railway track Rokycany – Plzen modernization. The following paper described practical experience gained with the innovative support of cross-passage openings, which was realized by short steel dowels grouted within the segments of the EPBM segmented liner. The paper is a continuation of the paper published in WTC 2015, which described the design aspects of the grouted dowels support, while the following paper concentrated on the production, and the performance of the dowel support observed during the breakout for the cross-passages openings. The connection by grouted dowels was patented by Metrostav, a.s. Company THE EJPOVICE TUNNELS CONSTRUCTION The Ejpovice tunnels construction started in 2013. The start of the high speed train operation through the tunnels was planned for 2018. The project was funded by the state government with the support of European Union funds of up to 70%.The tunnels were excavated with one EPBM (Earth Pressure Balanced Machine) with the external diameter of 9.89 m. The segmental liner inner diameter was 8.7 m, and thickness of 0.4 m. First, the South tunnel tube was excavated from the East portal, then the EPBM was pulled back through the South tunnel, and the excavation was started from the same portal for the North tube. After the South tube was freed from the EPBM excavation operations the cross-passage construction started. Due to the short time schedule, in the North tube the cross-passage construction started while the tunnel was still under construction. Therefore, the cross-passage construction was performed concurrently with the segments transportation, and with the EPBM pull-back through the tunnel. There were 8 cross-passages along the tunnels with a maximum distance of about 500 m, Fig.1."

Jan 1, 2016

By W. X. Yin

Electrowinning of lead from aqueous solution of PbCl2 and electrowinning of manganese dioxide from aqueous solution of MnCl2 are two research focuses in hydrometallurgy. This paper investigated a new process of simultaneous electrowinning of lead and manganese dioxide in chloride medium. The simultaneous electrowinning process in chloride solution not only can prevent chloride from liberating at anodes but also obtain two electrolysis products and decrease electric energy consumption. Diaphragm cell is used in the simultaneous electrowinning process to form separate anode and cathode compartment. The effects of temperature, HCl concentration in anolyte, NaCl concentration in catholyte and electrolysis time on current efficiency and cell voltage are studied. The results indicate that current efficiency of anode and cathode for 5 hours is 99% and 96% respectively, average cell voltage is 1. 701V, the weight ratio of lead and manganese dioxide produced at electrodes is 2. 39:1 under the optimum conditions. As anode products, manganese dioxide is ??MnO2, content of which in the products is more than 92%.

Jan 1, 2014

By Lakshman D. Jayaweera

Today's rapidly developing and changing technologies and industrial products and practices frequently carry with them the increased generation of materials that, if improperly dealt with, can threaten both public health and the environment. Mercury is an element that poses great problems in the many forms in which it is to be found in the mineral processing industry. These forms are often contained in hazardous wastes and residues which may be unstable, and in which the contained mercury has value. This paper presents some of the stabilisation and recovery methods which are based on hydrometallurgical techniques and thermodynamic stability considerations.

Jan 1, 1994

By T. E. Durney

In the Fall of 1987 The Wellmore Coal division of The United Company installed a fines separation circuit in its #20 plant near Big Rock, Va. The addition of the fines circuit included a bank of classifying cyclones and two flotation units; one a conventional 4 cell, 34 m3 Wemco cell, the other an 2.4 meter diameter by 7.6 meter tall, 28.3 m3 column flotation cell. The new fine coal separation circuit is depicted in Figure 1. The column flotation cell is manufactured by the Deister Concentrator Company, Inc., under the trade name Flotaire. The Deister Flotaire column cell utilizes a counter current flow arrangement and a different means of generating air bubbles than that of conventional mechanical flotation cells found in coal processing plants. Other features include diffusers for additional air supply and a froth washer. This cell is one of the few commercial scale column cells processing coal.

Jan 1, 1990

By G. J. Conroy

Cable whip occurring during normal movement of a shuttle car can result in a personnel hazard and excessive tensions in the cable. This Bureau of Mines report discusses preferred payout and reel-in torque settings to reduce cable whip. A simplified adjustment procedure is described.

Jan 1, 1974

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, R. Tichy, W. Ecker, M. J. Mikl-Resch, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (Figure 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (Figure 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By E. Gutierrez-Miravete

Hot pressing processes are widely used to shape metallic, ceramic, and glass components. The process is an essential step in manufacturing ceramic fibre-glass matrix composites. The paper describes the use of computer simulation by the particle method, to the analysis of the deformation and flow of glass during hot pressing. The hot glass is represented by an assembly of interacting particles which deform in response to the applied pressure. The results, which should be regarded as complementary to continuum-based studies, provide useful insight about the hot pressing process.

Jan 1, 1990

By F G. Cooke

"This paper describes a medium-sized copper mine's results in making innovations and changing operational practices to combat increasing expenditures due to higher labour and supply costs, extended workings, scarcity of experienced manpower and problems created by deteriorating ground conditions.OPEMISKA COPPER MINES (QUEBEC) LIMITED is located at Chapais in the Chibougamau area, in central eastern Quebec, approximately 300 miles north of Montreal and 150 miles north west of Lake St. John. The latter area, developed by lumbering and farming, has supplied the majority of the employees, who, with training and experience and a desire to work and improve themselves, have become the backbone of the Company's 600 personnel.Opemiska began production in 1954 at a rate of 400 tons per day, using diesel power and road transportation. The rate was progressively increased and, by 1959, with hydro-electric power and rail transportation, the mine had reached its present production rate of 2,000 tons per day. It has produced concentrates containing over 430 million lbs of copper."

Jan 1, 1968

By F. Y. Kang

There are rich resources of natural graphite in China. It would be a good opportunity to upgrade national graphite industry if natural graphite with modification is used in lithium ion battery. Micro-crystalline graphite in high purity was coated with a carbon film on the surface. The initial cycle efficiency was improved to be 89.9% and cycle stability was remarkably improved. The experiments proved that microcrystalline graphite with carbon coating have excellent electrochemical performances at low cost as anode materials for lithium-ion battery. In addition, H2SO4-GIC technique was used to prepare the natural flake graphite powders with mild-exfoliation. Sub-micro and nano pores were found in the graphite samples. In correspondence the reversible capacity, rate capacity and cycle life were improved, which would meet the demand of high-power lithium-ion battery. Natural graphite is the most promising anode material for large-scale lithium-ion batteries. The demand of modified graphite grows up greatly in the market. Microcrystalline graphite with surface coating and flake graphite with mild-exfoliation are the promising commercial anode materials for the industry of lithium ion battery.

Jan 1, 2014

By Michael K. Rhodes

A 120 tonne per day BacTech bacterial oxidation plant treating refractory gold concentrates for Gold Mines of Australia's Youanmi project in Western Australia commenced operation September 1994. This was the first commercial application of the BacTech process. A pilot plant trial on concentrates produced from Youanmi ore was carried out at BacTech's laboratory in Perth. Results and measurements from this trial were used by Signet Engineering Pty Ltd to design the commercial plant. This paper cover the results obtained from the piloting, their implementation in the plant design and the initial commissioning of the full scale plant.

Jan 1, 1995

By J A. Braithwaite

Social licence to operate is not a new concept for the mining industry, referring to stakeholder approval or acceptance for the activities and impacts of a project, company or industry. It is intangible, dynamic and non-permanent, hence it needs to be earned and then maintained (Thomson and Boutilier, 2014). It has also been argued that social licence extends beyond building approval or acceptance, into engagement for long-term development (Owen and Kemp, 2012).There are many examples where stakeholder opposition – or withdrawal of social licence – have increased capital and operating costs, extended schedules and impacted reputation. At its extreme, the withdrawal of social licence to operate can also contribute to or be the catalyst for mine closure.The key benefit of obtaining a social licence is a reduction of risk. Stakeholder support and advocacy, as well as the implementation of social performance programs that contribute to social licence, can be beneficial in terms of schedule, costs and other benefits.While decisions to close a mine are generally driven by resource availability or economic conditions, the social, economic and environmental legacy remaining post-closure is of importance to many stakeholders. With a number of significant mines now approaching closure within Australia, we are seeing heightened community concern about the economic and social impact of mine closure and the success of land rehabilitation. So how does the concept of social licence to operate extend into the closure phase of the mining life cycle?CITATION:Braithwaite, J A, 2016. Social licence to close?, in Proceedings Life-of-Mine 2016 Conference, pp 176–179 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By M McGrory, A Rodolfo, J Paredes, L E. Manguba, K A Villaspir, G Webb, R Setiagani, H Cardenas

"OceanaGold’s Didipio operation has been in operation for three years. Integral to the flow sheet design is a flash flotation circuit treating a portion of cyclone underflow, consisting of an Outotec SK-500 flash rougher and an Outotec TC10 flash cleaner and a SB-2500 falcon treating flash rougher concentrate to recover fine free gold.Flash copper recovery has been holding steady at 60 per cent, while flash gold recovery at 50 per cent. Gold recovery from the gravity circuit is 22 per cent, bringing the overall flash plus gravity gold recovery to 72 per cent.Operation of the flash rougher is mainly by pulp level control. Control of copper grade in the flash cleaner is mainly controlled by air inflow and flash cleaner pulp level control drives copper recovery. Gold recovery around the circuit is mainly driven by gold head grade.SB-2500 concentrate is scalped with a 250 micron screen with the coarse fraction reporting to a SB-250 falcon, concentrate of which combines with the screen fine fraction to a Gemini table.Citation:Cardenas, H, McGrory, M, Webb, G, Paredes, J, Setiagani, R, Villaspir, K A, Manguba, L E and Rodolfo, A, 2016. Didipio Flash Flotation and Gravity Recovery Circuit, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 123–126 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"Iron ore in Minnesota probably carries a heavier tax burden than any mineral in any other place in the world. The State Tax Commission, created in 1907, originated the system, and with the assistance of the School of Mines is constantly making such adjustments, changes and increases as appear necessary, in order to place mineral reserves on the assessment rolls at their true and full present taxable value. The ore bodies on the Mesabi are so well defined by drilling and underground devel¬opment that it is possible to estimate very exactly the volume on every forty acres of land taken as a unit. This is done by the operating or holding company and reported annually to the Tax Commission, Who check the estimates, having all data, and- proceed to fix the valuation for taxation purposes.The first step is to ascertain a general average selling price in open market, over a period of years ; then the total cost per ton (exclusive of royalty) to produce and market the ore. The difference between the average selling price and producing cost per ton is taken as the future full value per ton. This is then discounted at a rate of interest that represents the present and possible future worth of money, over a period of years that will be required to exhaust the ore body, giving the present full value per ton., Iron ore is taxed at 50 per cent of its full value, while other property is taxed at 33 1/3 per cent and 25 per cent."

Jan 1, 1920