Search Documents

By Shawn T. Sorrell

Phillips Coal Company (PCC) submitted the first surface mine permit application under the Office of Surface &lining approved regulatory program of the State of Louisiana. This application for the Oxbow Lignite Surface Mine which is located approximately 64 kilometers (40 miles) southeast of Shreveport, Louisiana was submitted in March 1981. The State of Louisiana Office of Conservation, Surface Mining Division, assigned this application number LSM-1, indicating it is the first one submitted in Louisiana history. The permit area for the Oxbow Mine encompasses 6,251 hectares (15,627 acres). Of this total permit area, 5,862 hectares (14,656 acres) were classified by soil type as prime farmland by the U.S. Soil Conservation Service (SCS). Prime farmland acreage in the permit area became a major central issue in our early planning stages and throughout the permitting process of the Oxbow Mine, due to the magnitude of acreage involved.

Jan 1, 1982

By Z. Smieszek, Z. Szota, P. Gajowski

"A new method for measuring the total quantity of suspensions contained in the electrolyte during copper electrorefining has been developed by the Institute of Non-Ferrous Metals, Gliwice. Electrolyte purity, and the suspensions content in particular, is of essential importance for the quality of electrolytic copper produced during the process. Suspensions contribute to the increase of slime impurities in electrolytic copper and increase losses in noble metals. Up to now, the laboratory method has been used for the· process control which provides analytical results with considerable time delay. Therefore, it is useless for the process control.The measuring method developed enables continuous measurements of a suspensions content directly within the stream of the flowing electrolyte. The principle of measurement is based on changes in optic properties of the electrolyte with varying suspensions content.1. IntroductionIn copper electrorefining, it is essential that the final product quality be maintained. If suspensions are present in electrolyte, the content of slime impurities in electrolytic copper, (such as Pb, Ag, Bi, Sn, Sb, and As), increases which can result in the occurrence of the so-called slime dendrites on cathodes, thus debasing the quality of the product. As a normal suspension content in electrolyte, the contents in the order of several mg/l are considered, usually not more than 5-6 mg/l, while contents exceeding 20 mg/l are referred to as an alarm state. Suspensions present in an electrolyte are usually a light fraction of anodic slime whose main components are metallic silver, lead sulphate, complexes of antimony and arsenic, and sometimes even calcium sulphate; they are mainly composed of very small particles of lead sulphate and antimony complexes. Sometimes - - in case of alarm states - - the so-called ""wandering slims"" can be observed, which are composed mainly of arsenic and antimony complexes. These ""wandering slims"" make a serious technological disturbance. In normal operating conditions of the electrorefining plant, an increase of suspension content can result from such reasons as crack of filter cloth in a slime filter, turbulent flow of the electrolyte, anodic passivation, aeration of the electrolyte, and improper servicing of an electrolytic tank. It is necessary to continuously control the suspensions content in electrolyte for proper electrorefining."

Jan 1, 1989

By Gerardo Noriega

Aeromagnetic compensation plays an important role in most airborne geophysical exploration programs, dealing with the modelling and elimination of interference effects generated by the aircraft flying in the Earth’s magnetic field. This work discusses broadly recent developments on adaptive compensation (which allows continuous optimization of the solution through a recursive algorithm), real-time compensation of on-board electronic systems (whose effects are not captured by the conventional model), attitude-reference sensors, compensation of UAV platforms, and various modelling issues.

May 1, 2008

By O. D. Maurice

Feldspar mining in Canada came to an end during 1972 after many years of continuous activity. The deposits are not exhausted and the domestic demand for this product is expected to continue at about the same level as in recent years. The size of the industry does not justify the installation of expensive equipment in the mills, but it is believed that a modest profit could be made by a small operation using rudimentary methods of separation. Largescale and accurate mapping of the pegmatite dykes could help in planning mining operations for a better recovery of a uniform product.

Jan 1, 1973

Drilling is a common process in mining and petroleum engineering applications which have different objectives. For example, drilling deep boreholes in tight gas formations and gas shales is becoming more popular in the oil and gas industry. By contrast, drilling deep small sized holes for mineral exploration in hard rocks is performed to obtain samples for grade analysis purposes. In both applications optimising the drilling process includes using the most effective operating parameters such as rotation speed and weight-on-bit in order to maximise the rate of penetration. Obtaining the optimum drilling parameters requires sensitivity analysis over a range of data, which would be costly and time consuming during real field operations. Therefore, conducting several experimental simulations in the lab would be very beneficial before field operations begin. A drilling rig was designed and developed to simulate various drilling scenarios. The rig works in conjunction with an existing true triaxial stress cell (TTSC) which is in use for different petroleum related applications. The rig allows drilling into a cubic rock sample of up to 300 mm size. Three independent stresses can be applied to the sample to simulate real in-situ field stress conditions while the sample may be saturated with fluid. A significant feature of the rig is its ultra-high speed rotation which can rotate up to 8000 rpm: this is to simulate hard rock drilling for mineral exploration applications where large weight-onbit could damage the bit cutters. With the proposed design, a drilling fluid of any type can be circulated in the simulated borehole similar to the real situation, to study its effect on drilling performance. The TTSC drilling lid is equipped with torque and drag measurement systems which are two important drilling parameters to be recorded during drilling operation. It is believed that this new drilling rig will open opportunities for performing major new applied research in the area of more efficient drilling in both oil and gas bearing formations and mineral exploration applications.

Aug 1, 2013

By T. Watanabe, T. Fujiwara, S-Wan Song, Y. Nakagawa, R. Teranishi, M. Yoshimura

"We have tried a new method to fabricate cobalt oxide films onto porous films directly by an electrodeposition method at low temperature. The porous substrate films (membrane-filters and paper) were placed between a LiOH solution and a CoSO4 solution and treated under electricalcurrents of ~1 mA/cm2 using carbon cathode and anode. Effects of temperatures, flow rates and electrical currents have been investigated. As a result, we found that the LiCoO2 films and Co3O4 films were successfully fabricated on paper and/or porous PTFE filters at 120 °C, while CoOOH films were deposited at 80 °C. Furthermore, LiCoO2 films did not cover whole the substrates, but was fabricated just over the anode. The chemical reactions of electrodeposition were also considered from these results.IntroductionRecent agreements on global environment require rapid progress of low energy and low waste processings for the fabrication of thin films that succeed to the mass production with the high consumption of the fossil fuels (such as physical vapor deposition°, chemical vapor deposition2), dip coating with firing3) etc.). The total energy consumption in aqueous systems should be the lowest among all these processing routes, because a much lager excess of energy is necessary to create melts, vapor, gas, or plasma than to form an aqueous solution at the same temperature4)The ""Soft Solution-Process"" (SSP) was one of the best concepts to realize the low energy and low waste fabrication of inorganic materials. 5) Generally speaking, SSP gives similar results to any other processing using fluids (such as vapor, gas plasma) and/or beam/vacuum processing. However, the total energy consumption of all these possessing routes should be the lowest in aqueous systems, because a much larger excess of energy is necessary to create melts, vapor, gas or plasma than to form an aqueous solution at the same temperature (Fig. 1). This idea can be easily demonstrated, using the simple example of BaTiO3. The energy diagram for the formation of BaTiO3 from various precursors is shown in reference 4. The driving forces (AG) for representative synthesis reaction of (1), (2), (3), (4) and(5) are 38, 727, 3685, 17 and —14kcal/mol, respectively at room temperature. 6' 7"

Jan 1, 2000

By B. H. Zhao

A low grade Pt-Pd ores, with 1g/t Pt and 0.13g/t Pd, and 8.70% Fe and 2.50% P2O5 is experimented to recover of Pt and Pd. The flowsheet is proposed which consists of Pt-Pd selective flotation, apatite flotation from tailings of Pt-Pd flotation, magnetic separation of magnetite from apatite flotation tailing. With butyl xanthate, N-ally group-O-isobuturyl-thioanimoformate and Sodium y-89 xanthate as collectors, sodium silicate as depressant, and sodium carbonate as pH regulator, a concentrate, assaying 324.52 g/t Pt and 45.62 g/t Pd, is obtained with recoveries of 87.23% Pt and 76.89% Pd from surface ore. A concentrate, assaying 1693.53 g/t Pt and 64.12 g/t Pd, is obtained with recoveries of 88.54% Pt and 83.78% Pd from primary ore. At same time, A iron concentrate assaying 64.12% Fe with a recovery of 24.94%, and a apatite concentrate assying 30.32% P2O5 with a recovery of 80.12% are obtained.

Jan 1, 2014

By J. P. Rider

Along with increased production from longwall units has come the likelihood of increased worker noise exposures. In recent years, equipment has become larger, more powerful, and noisier than its predecessors. For these reasons, the Mining Division of the National Institute for Occupational Safety and Health (NIOSH) is investigating worker noise exposure on longwall faces and researching possible solutions to reduce this exposure. Part of this research effort involves studying the effect of covering the underside of longwall shields with acoustical material to reduce reverberating noise along the face. Experiments using acoustical absorptive insulation to cover the undersides of the shields, shearer body, and the shield supports were conducted at the full scale simulated longwall test facility located at the Pittsburgh Research Center. Sound levels were recorded every l.5 m [5 ft] along a 15.2 m [50 ft] section of the simulated face for all of the conditions tested. The analysis of the data indicated that a 2.0-3.0 dBA noise reduction was achieved between the shearer drums and a 4.0-5.5 dBA attenuation was attained upwind of the headgate drum.

Jan 1, 1997

By Wang Chen

COREX process is briefly introduced. A static model combining a set of mass and heat balance equations has been developed. Taking the specified inputs from the graphical user interfaces, the model is capable of calculating the consumption of raw materials and fluxes, the volume and composition of the slag and the volume and composition of the generator gas. The model enables the examination of the changes of materials and energy flows induced by the variations of operational parameters and raw materials chemical analysis. The model allows a detailed process analysis and adjustment of the plant operation and can thus be used to improve plant operation.

Jan 1, 2008

By Malcolm Heyburn

Airborne and ground magnetic surveys were made over and in the vicinity of the Sanford Hill ore body at Tahawus, Essex County, New York. These geophysical surveys served to: l. delineate, lithologic and structural features associated with the ore bodies; 2. indicate a major extension of the Sanford Hill ore body; and 3. guide a drilling program to prove this extension. The titaniferous magnetite ore body at Sanford Hill is associated with gabbro occurring in anorthosite. The contrast in the magnetic susceptibilities of these rock types, reflected in the magnetic measurements, allows geologic-mapping showing rock types and inferred structural features. The anomalous magnetic high of the airborne magnetometer survey indicated a southern extension of the Sanford Hill ore body. Diamond drilling, guided by the airborne and specifically the ground magnetic results, substantiated this interpreted ore extension to be of major magnitude.

Jan 1, 1961

By J. L. Gartshore

PRACTICALLY all of Quebec's chrysotile asbestos production derives from twelve mining and milling operations located in the "Eastern Townships" area of the province. The annual output of these twelve operations exceeds one million tons of chrysotile asbestos, valued at over one hundred million dollars, and is shipped to manufacturers spread over all six continental areas of the world. A total of approximately twenty million ton of asbestos ore yearly, or about seventy-five thousand tons a day, is mined. Individually, the operations vary in size from about two thousand tons to thirty thousand tons per day. Removal of waste rock and overburden to develop these ore tonnages varies greatly from one mine to another, but would probably average out at about a one to one ratio.

Jan 1, 1962

By J. R. Hartin

Traditionally, many of the advances in casting technology have been made by expensive and time consuming trial-and-error methodology. Modeling of the complex solidification process promises production of castings which are made "right the first time." Even though several models are available for simulation of conventional casting processes, none of them address this relatively new technology of investment cast titanium aluminides. In this paper, modification and application of a transient, three-dimensional, fully coupled fluid flow and heat transfer solidification modeling computer program to the analysis of centrifugally cast titanium aluminides is discussed. The predictive results of the program are compared to qualities of actual cast parts for validation.

Jan 1, 1992

By Jincheng Hu, Honggang Zhong, Qijie Zhai, Congsen Wu, Cheng Zhang, Jingzheng Ye

"The influence of cooling intensity on the solidification structure and ferrite phase content of a new duplex stainless steel (DSS) was investigated by using a thermal simulation setup for continuous casting. The results showed that the characteristics of the solidification structure were similar to their industrial scale manufactured slabs, including chill zone, colunmar zone and equiaxed zone. And austenite morphologies were mainly primary and secondary Widmanstatten sideplates as well as intragranular Widmanstatten plates. In addition, it revealed that the ferrite content increased with an increasing distance from the chill surface and decreased at colunmar to equiaxed transition (CET) position, then the value remained relatively stable at equiaxed zone. Furthermore, the ferrite content presented the same trend with the cooling intensity ranging from 100 mL/min to 2000 mL/min with the values just varying in a slight range.IntroductionThe duplex stainless steel (DSS) is the kind of steel that ferrite phase and austenite phase occupy about 50% respectively, or the content of the fewer phase has to be more than 30% [l]. The success of modem duplex stainless steels is to a large degree due to their higher strength than austenitic stainless steels, higher toughness than ferritic stainless steels, good weldability and high resistance to stress corrosion cracking as well [2,3]. The cost of stainless steel production continues to soar in recent years due to the increasingly higher price of Cr. In order to decrease the production cost, a new type of duplex stainless steel was developed by Bao steel [4]. This newly developed duplex stainless steel had low Cr content compared with 2205 DSS, and was expected to be applied into automobile industry. However, this type of steel was still in the initial stage of development, and the influence of continuous casting process on its solidification process and structure was still unclear, which needed to be studied further. Several works published in literature presented the effect of continuous casting conditions on duplex stainless steel (DSS) 2205, 2304 [5,6]. It was discussed that the cooling intensity in the chill-side had little efficient influence on the phase transformation. In this paper, the effect of cooling intensity on the solidification structure and ferrite volume fraction of this DSS at a given cooling rate was investigated."

Jan 1, 2014

By Masatoshi Ogasawara

Saganoseki smelter & refinery operated two flash smelting furnaces, producing a combined 330,000 metric tons per year (hereinafter mtpy) of copper. In 1996, however, it successfully shifted to a single furnace operation while maintaining production at the same level. Since then, the production capacity has been further increased to the present 470,000 mtpy by technological improvements. Also, in order to reduce the converter load which represents a bottleneck in efforts to increase production, the matte grade was gradually increased and currently runs at 65 to 66% attaining the low copper content in the slag (hereinafter slag loss) of 0.7 to 0.8%. This paper introduces some improvements, recent operation results and thermodynamic analyses.

Jan 1, 2003

By P. Fecko

The objective of the paper was application of bacterial leaching on two brown coal samples from locality Mine Druzba, seams Antonin and Josef (Sokolov brown coal basin, Czech republic). Based on the results of bacterial leaching and petrologic analyses of the given samples, it is possible to say that application of bacterial leaching gived good results. Applying bacterial leaching it is possible to remove from 34% to 47% of total sulphur and from 45% to 64% of pyritic sulphur from the coal.

Jan 1, 2014

By S. K. Dimitrov

?Ellatzite Med? is one of the biggest mining companies in Bulgaria, processing about 12,000,000 t of ore per year. Waste materials left after extraction of copper concentrate are deposited in tailings dam ?Benkovski 2?. The hydraulic structure is built according to the downstream method, through hydrocyclonization where the downstream batter and the body of the wall are formed by the separated coarse sand particles of the separated tailings. In connection with the prolonged concession of Ellatzite Med and the enlarged capacity of Benkovski 2, the tailings dam has expanded on to the surrounding terrain. To guarantee a normal hydrocyclonization and build up of a tailings wall during waste deposition from the ore mill, the technological scheme of the hydraulic transport system of Benkovski 2 has been changed.

Aug 1, 2013

By Henning E. Soderberg

Yesterday, air pollution was somebody else's problem -- today, it is everybody's problem. The coal industry with thermal coal drying, is aware of their problem and the necessity of doing an acceptable job; however, there is much to be said as to how good a job is required and what performance limits should be set up. American Air Filter Company has been one of the pioneers in the solution of the thermal coal dryer dust problems, Because of high moisture content, products of combustion and occasional temperature surges, only wet collection has been considered as the practical approach. Our first installation goes back some 12 years with a total to date of 29 Individual wet collectors, each, fabricated of suitable corrosion-resistant material, at 14 operating plants. To eliminate a potential air pollution problem, a performance requirement of not more than approximately one-quarter (1/4) grains per cubic foot in the dust collector discharge was used. In nearly all installations, operating performance surpassed requirements, but discharge stacks were not entirely free of discoloration. However, plant nuisance and air pollution complaints were eliminated. This satisfactory performance was accomplished by medium priced wet dust collectors operating at a 4-6" W.G. pressure drop with cater drain requirements of about 1 gallon of drain water per 1000 cubic feet of air exhausted.

Jan 1, 1962

By Michael Karmis, Syed Muhammad Tariq, Zeshan Hyder

This paper analyzes the blast design for lime stone quarries of two major cement plants in Pakistan. The production blast of these quarries was resulting in excessive boulders production. At some instances, the rate of boulders production was approximately 10%-15% of the main production blast i.e. if a round of main blast gave around 4000 tons of material; almost 400 to 500 tons of that material was in the shape of massive boulders. This gave rise to increased operating costs requiring boulders collection, drilling and secondary blast.

Jan 1, 2012

By Bruce Macdonald

Operational monitoring of slope stability can be achieved by space based InSAR monitoring platforms. Natural and man-made rock slopes are monitored using a novel stack-based InSAR method that exploits both persistent point scatterers (PS) as well as coherent distributed scatterers (DS) such as areas of pavement and sparsely vegetated surfaces. The new method, Homogenous Distributed Scatterer (HDS)-InSAR identifies InSAR targets by using adaptive multilooking of statistically homogenous pixel neighbourhoods combined with thresholding the differential temporal coherence of each target candidate with respect to its surroundings. HDS-InSAR preserves PS and therefore forms a direct generalization to our proven DualScale-PSI method. The density of HDS exceeds that of PS by more than an order of magnitude often providing essentially continuous coverage over urban and industrial landscapes featuring a mix of infrastructure with mostly bare soils or rock surfaces. The improved coverage enables better definition of surface motion and underlying geology, which will lead to superior interpretation of the geophysical mechanisms causing the surface deformation, e.g. through improved integration with 3D deformation modeling. We illustrate the performance of our new HDS-InSAR method compared to DualScale-PSI using displacement results from Vancouver, Canada; Bingham mine, USA; and the Palabora mine, South Africa.

Jun 1, 2012

By Versiane A. Leão

The hydrochloric leaching of chrysotile tailings and soapstone powders) is discussed. This two materials are magnesium compounds associated with carbonates and iron oxides. In this work the chemical and physical characterization of formers is presented and the thermodynamic analyses of leaching is carried out. Magnesium extraction is almost complete for chrysotile tailings while, for soapstone powders, one can be reached 60%. The behavior of iron and calcium impurities is discussed.

Jan 1, 1997