Search Documents

By Jung-Hum Lee, Young-Joon Lee, Eui-Joon Hong, Seon-Hong Kim, Chan-Dong Kim, Keon-Woong Jeong, Ki-Lim Kim

"Subsea tunnel needs to be built over 50km long to connect between nations and continents. However there are only 19 tunnels longer than 5km in Korea, and there is no history of constructing and operating a tunnel longer than 50km. As the concept of a subsea tunnel, which withstands high water pressure and has an extremely long length is completely different from that of a land tunnel, all kinds of the latest technologies for tunnel construction are required such as survey and analysis of geology, design and construction under high water pressure, ventilation and prevention of disasters within an ultra long tunnel. Therefore, this paper describes the determination of tunnel cross-section under a high speed railway, structural stability, ventilation and fire safety under construction and operation, etc. through the virtual project for the length of 108km subsea tunnel under high water pressure of maximum 20bars from Honam to Jeju island in Korea. 1. INTRODUCTION The Honam-Jeju virtual project is subsea tunnel project to link from Honam(land) to Jeju(island) extending the currently operating Honam high speed railway line, and the same express train(t=18, design speed 350km/h, total train length 200m) operating at Honam line is applied in this project. As Honam-Jeju site is approximately 80km in straight distance with 160m maximum depth, subsea tunnel project should determine the various issues such as air quality/ventilation, aerodynamics, temperature, drainage, fire & life safety, structural stability. Figure 1. is the plan of subsea tunnel, with be constructed using Shield TBM. This double tube-Single track is composed of cross passages (every 350m in general section and 40m in emergency station), service tunnel, pressure relief ducts (every 250m), cross-over tunnels, shafts and emergency stations. 2. ALIGNMENT AND SITE CONDITON This project is planned as an ultra long tunnel of total length more than 105km via existing islands between Honam and Jeju island because straight alignment requires an artificial island which has high cost and construction risk, by deep water depth, though this is the shortest distance (see Fig 2). Water depth and topography in project site is divided into two blocks by Chuja Island. In first block to Chuja Island, depth of the water is 40m on average and maximum 60m, which indicates gradual change of water depth relatively. Also, outcrop bedrock is widely distributed near island."

Jan 1, 2016

By d&apos, L. F. G. Assumpcao

Kaolin samples from Rio Capim resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the color removal process. Coating clays and delaminated clay were tested. Retention time (or pulp injection velocity), magnetic field intensity and matrix type were the' variables studied. The feed brightness ranged from 84.7 to 87.6 % ISO for the coating clays and from 80.7 to 85.4 % ISO for the delaminated clay. The results showed unleached brightness values higher than 88 % ISO for coating products and higher than 87 % ISO for the delaminated product, using a conventional magnetic separator with an applied field of 1.5 to 2.0 Tesla. With a maximum field intensity in the superconducting machine of 5.0 Tesla, unleached brightness values higher than 88.5 % ISO for both coating and delaminated clays were attained.

Jan 1, 1995

By J. Wiedenroth

Since the end of the 1970s Pipe Conveyors have become increasingly important for conveying bulk materials because they have some specific advantages over conventional troughed belt conveyors. FLSmidth KOCH Pipe Conveyor represent the marked-leading know how of the former KOCH Transporttechnik GmbH, which belongs to the FLSmidth Group since January 2007. Pipe Conveyors from FLSmidth KOCH are already being used successfully at more than 260 locations around the world. Their special properties, their extreme flexibility, the horizontal and vertical changes in direction without transfer points, the small space requirement, the low-noise running and their optimum protection of environment and material without any additional casing mean that Pipe Conveyors can provide transport solutions that are often far superior to other conveying systems. The utilization of these many advantages will be illustrated in the following example of the world?s longest Pipe Conveyor at Cementos Lima, the Peruvian cement producer.

Jan 1, 2010

By L. Shang

In conventional continuous hot rolling processes, metals are usually reheated to a temperature such that the workpiece will maintain appropriate hot working characteristics as it proceeds through the rolling mill, assuming that the temperature is continually decreasing. Metallurgically, reheating will reduce micro-segregation in the as-cast material, may increase the as-cast grain size and will affect any second phase particles present in the as-cast structure. All these changes can affect the hot working characteristics, and the final as-hot rolled microstructure. In order to study the effect of reheating on AZ31 magnesium alloy, a plate sample was cast in a water cooled copper mould and a series of compression tests was performed at a temperature of 350 °C, strain rate 0.01 5-1, and strains from 0.2 to 1.0, after different reheating schedules. It was found that there is no significant difference in flow behavior between the as-cast sample and all but one of the reheated ones. The reheat treatment of the 'anomalous' sample was a two stage heat treatment; it was first reheated to 450 °C, cooled to room temperature, then reheated to 350 °C. The effect on the flow curve was to increase the flow stress. This result may be related to changes in second phase particle characteristics.

Jan 1, 2006

By A. Musschoot

"The paper will review general types and designs of vibratory feeders, describing briefly the design features and characteristics that apply to the application of specific types. Control considerations for selecting types will be dis• cussed, such as fixed or adjustable, manual or automatic, individual or multiple bank, and process requirements. Design parameters for hopper openings and installation geometry will be discussed, including consideration of material size distribution, segregation, moisture content and other characteristics, based on practical applications and experience as well as theory. Pan designs and the selection of pan materials will also be discussed with reference to wear, corrosion, impact and practical economic factors."

Jan 1, 1972

By Martin Junker

This Notwithstanding all the debates on climate change and renewable energy, coal remains the world's no.1 primary energy source even in the 21st century. In 2011 alone, total output rose from 420 million t to around 6.6 billion t. Similar growth rates are also expected for the next few years. In order to meet demand, new seams are being tapped and others mined far more extensively. In most cases, this means a move from open-cast to deep mining, and extracting coal from ever greater depths. At the same time, extraction processes such as the room and pillar method are being replaced by longwall mining, which significantly increases seam yield and therefore output. The depth of extraction with new, modified mining methods is increasing rapidly around the world - in most countries, much more rapidly than the corresponding expertise. A trade in mining expertise has therefore developed alongside the coal trade proper. Germany relies on coal imports, but can export mining industry services and advanced mining equipment. Geological conditions in the Ruhr and Saar coalfields forced Germany to drive forward development of deep working for hard coal years ago. For 30 years now, Germany has been mining hard coal at depths of over 1,000 m, and excavation is now at depths up to 1,600 m. Deeper extraction and more extensive excavation posed new challenges for both miners and equipment. Intelligent logistics, modern roadway development methods and longwall mining with ploughs or shearers combined with optimised process coordination offered pioneering solutions - solutions to enable costeffective coal extraction in the long term without compromising safety. Countries such as Russia, the Ukraine, China and the Czech Republic, where extraction is now reaching similar depths, can now benefit from this experience: they do not need to go through the same process of trial and development, but can draw on Germany's findings and ultimately save on costs. Now, Germany is offering this knowledge and experience on the international market on a client- and deposit-specific basis to continue providing mining countries with safe and cost-effective coal mining solutions and secure the energy supply. The presentation gives a number of examples of how international mining companies have used expertise from Germany to better meet the challenges of deep mining.

Aug 1, 2013

By Judith S. Chan

With the increasing awareness of the need for the reduction of carbon emissions globally, geothermal energy, which offers a potential for cleaner energy generation, is one potential new source. In Alberta, these geothermal resources are likely to be found in the sedimentary basin, or in the deeper crystalline basement rocks. Alberta exhibits a very low geothermal gradient compared to other existing geothermal fields located in areas of volcanic and tectonic activity. To mitigate this effect, the focus in Alberta will involve the development of engineered geothermal systems (EGS) in the target resource. The first goal for EGS research and development is to develop a detailed geological-geophysical characterization of selected sites to delineate potential geothermal reservoirs in Northern Alberta. One of the selected sites is in the Fort McMurray area. The deepest well drilled in the oilsands areas of Northern Alberta is located just west of Fort McMurray. It has a depth of 2363 m and as such can provide details on the physical properties of the rocks, the state of stress, and the existence of fracture porosity toward geothermal investigations. To date, we have acquired temperature logs to study the change in geothermal gradient with depth, and a series of petrophysical logs to study the finer scale structure of the rock formations with vertical resolutions in the range of 0.05 cm to 80 cm. Our aim is to identify geological features such as zones of fractures in the basin and/or basement that could provide an indication of enhanced fluid flow potential ? a necessary component for any geothermal systems to be viable. Zero offset and walkaway vertical seismic profiles (VSP) were also conducted to measure the seismic responses at the borehole. VSP data can be used to delineate the structural and stratigraphic features surrounding the borehole that could not be resolved from surface seismic reflection data that are also available near the borehole. The full integration of well logs, VSP data and surface seismic reflection data are expected to provide a detailed characterization of the sedimentary basin and crystalline basement rocks of the Canadian Shield in Northeastern Alberta and will assist in future planning for drilling.

Jun 1, 2012

By Y Zhu, D J. Williams, M O’Neill, C Zhang, X Lei

A cover of inert material overlain by topsoil is required over compacted, seawater-neutralised red mud, a waste product from the refining of bauxite to produce alumina. The cover is to be revegetated, and it is necessary to demonstrate that the potential evapotranspirative-driven uptake of salts from the seawater-neutralised red mud will not impact the revegetation. An instrumented column was designed and constructed to test the evaporation-driven uptake of salts from compacted red mud into an overlying cover material with a thickness limited to 600 mm. The PVC column is 1.2 m high, with a 200 mm internal diameter. The column is instrumented with up to ten of each of moisture, suction, salinity and temperature sensors, together with a data logger, designed and manufactured at The University of Queensland (UQ) in Brisbane, Australia. The sensors were installed through the wall of the column at various depth intervals, with each set of sensors located at quarter points around the circumference of the column. Two pressure transducers were installed in the column to monitor the change of water level due to rainfall and evaporation. The column was filled with compacted red mud to a depth of 600 mm overlain by 600 mm of cover material, both sourced from the Queensland Alumina Limited (QAL) site in Gladstone, Queensland, Australia. The column is installed on a building roof at UQ, alongside a weather station, and will be subjected to the prevailing weather conditions for up to 1 year in the first instance, during which time the weather conditions and sensor responses will be continuously monitored. This paper reports on the instrumented column set-up and the early results obtained from the test.CITATION:Zhang, C, Williams, D J, Lei, X, Zhu, Y and O’Neill, M, 2018. Instrumented column testing of salt uptake from compacted red mud into a cover, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 220–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By S. Narra, M. Nelles, I. Eickhoff, S. Teitge

"The aim of the research is to develop a holistic process flow for the recycling of glass fibres from glass reinforced plastics (GRP) and carbon fibres from carbon fibre reinforced plastics (CFRP), wherein the dissolution of the fibre epoxy resin matrix, separation of fibre fractions and their renewed material use is intended. In clear distinction to the previous research and development projects, the aim here is to recycle complex composite structures such as dismantled/disused wind turbine rotor blades and end-of-life composite wastes. In the course of the study, mechanical, hydrothermal and thermal processes and their combined procedures will be developed. As the fibre length is a decisive quality criterion in the recycling of composite materials, the further focus of the study will be the development of upstream and downstream material processing, in which the fibres are retained in their original form. The evaluation of the recycled fibres obtained is based on the elemental composition, measurement and morphological evaluation of individual filaments by scanning electron microscope (SEM), micro tensile tests on single fibres and their comparison to virgin fibres. The resulting process water is analysed by gas chromatography and mass spectroscopy (GC-MS) and a potential recirculation is determined. In cooperation with companies from the composite processing industry as well as recycling companies, a return of the recycled fibres to the known manufacturing process will be examined and an energetic and economic evaluation of the overall process will be carried out. Ambitious aim of the study is to achieve an actual recycling instead of the present downcycling or the energetic utilization. INTRODUCTION As global warming increases, so does the awareness of consumption and production of energy. To counteract the effects of global warming, renewable energy has been increasingly used during the last two decades, not only in Germany, but worldwide. Both, hydropower and wind energy, hereby play a fundamental role. After the end of their useful life of 20 to 30 years, the wind turbines (WTs) are being dismantled. Due to their foundations and tower segments, their recycling rate hereby exceeds 90% by mass. So far, the resulting rotor blade waste played a minor role accounting for only 2 - 3 weight-% of the total plant. Rotor blades of modern wind turbines are made of glass and carbon fibers, which are embedded in an epoxy or polyester resin matrix, balsa wood, PU or PET foams as fillers as well as various paints and coatings. These wastes currently end up in waste incineration or are sold to non-European countries."

Jan 1, 2018

By Frank Otten, Jochen Greinacher

"In July 2017, Deilmann-Haniel signed a contract with IOO Slavkaliy to sink two 750 metre (m) deep freeze shafts for the Nezhinsky Potash mine in Belarus. This is the second shaft project where this technology is employed after two over 1,000 m deep shafts for a potash project in Saskatchewan, Canada, have been sunk by the application of the Herrenknecht Shaft Boring Roadheader (SBR) technology. Developed to sink shafts for green field projects in soft to medium hard rock, in frozen or unfrozen geology, the machine technology utilizes a roadheader-type cutterhead on a telescopic boom to mechanically excavate the rock, and a pneumatic mucking system to convey the muck from the face into the buckets. This leads to a manless face during the sinking cycle and thus a significant improvement in terms of workplace safety. For the Nezhinsky project, the SBR design was significantly modified in close cooperation between Deilmann-Haniel and Herrenknecht, based on the available experience and the special requirements of the project. Such modifications have been for example the adaptation of the Pneumatic Mucking System to cope with wet material as well as dry as originally planned or the shaft lining moving from shotcrete application to jump for and tubbing installation for which a step-change hands-off tubbing erector for the placement of segments was designed. Further modifications to optimize the machine technology for the requirements during shaft sinking were applied on the two machines for the Slavkaliy project as well as several revisions to match the special project requirements. The SBR is suitable for soft and medium hard rock up to 100 MPa UCS. The main design limits are maximum weight of the machine with 400 tonnes and length or height of 50 m due to the depth of the pre-sink. The Pneumatic Mucking System was changed in all components, sheaves and rope arrangement were redesigned and the concept of the hoist system was also re-engineered. The SBR in Belarus is configured for a daily sinking rate of three metres and all systems behind the cutting boom are not the bottle neck of the whole system. The works on site started in November 2017 including freeze hole drilling, construction works, site setup, installation of hoists winches, permanent headgears and other components required for sinking. The SBRs arrived on site in June/July 2018 and were preassembled on surface and then lowered into the 50 m pre-sink. SBR #1 started full face sinking in mid-December 2018, and SBR #2 in late January 2019. By the end of February 2019, the machines were at 150 m and 100 m depth respectively, and achieved up to 3.6 m/day concrete lined shaft. The SBR and the sinking system, the experiences, problems, technical solutions and performances of this challenging project will be presented in this paper."

Jan 1, 2019

By F. Qiming

By means of flotation experiments, potential-pH diagram, electrochemical testing and X -ray photoelectronic spectrum (XPS), the main factors (the thermodynamics and the property of surface products) influencing the separation of sulfide minerals (such as galena and chalcopyrite) in the collectorless flotation are studied. The actual conditions (Eh, pH) of separation are not conformable to the results of thermodynamic calculation. The kinetic behavior of oxidation of sulfide minerals and the property of oxidation products are the decisive factors of the separation of sulfide minerals in the collectorless notation.

Jan 1, 1992

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off....,gases from the copper ?and nickel flash smelting furnaces and converters? in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are presented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas.and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By Jozef Zmik, Sergey Dobatkin, Martin Fujda, George Raab, Libor Kraus

"The present work, likewise, deals with grain refinement of medium carbon steel AISI 1045 having different initial microstructure resulting from thermal and/or thermomechanical treatment (TM) applied prior severe plastic deformation. In case of TM treated steel, structure refinement was conducted in two steps. Preliminary structure refinement has been achieved due to multistep open die forging process which provided total strain Eef ~ 3. Uniform and fine recrystallized ferrite structure with grain size of the order of 2-5 µm and with nest-like pearlite colonies was obtained. The further grain refinement of steel samples having different initial structure was accomplished during warm Equal Channel Angular Pressing (ECAP) at 400°C. The microstructure development was analyzed in dependence of effective strain introduced ( Eef ~ 2.5 - 4). Employment of this processing route resulted in extensive deformation of ferrite grains where mixture of subgrains and ultrafine grain was found regardless the preliminary treatment of steel. As straining increases the dynamic polygonization and recrystallization became active to form mixture of polygonized subgrains and submicrocrystalline grains having high angle boundaries. The intensive straining and moderate ECAP temperature caused the partial cementite lamellae fragmentation and spheroidization as straining increased. The lamellae cementite spheroidization was more extensive in TM treated steel samples. The deformation behavior of for both steel structural state confirm the strength increase; however the work hardening behavior was modified with respect to initial structure of steel prior SPD processing.IntroductionIn the last years, ultrafine grained materials have attracted considerable research interest because they tend to possess high strength without sacrificing toughness and ductility. Microstructural refinement of steel is usually achieved by alloying and/or by thermomechanical treatment process, which modifies phase transformation. Recently, advancement of severe plastic deformation (SPD) techniques provides another efficient access for grain refinement of metals and alloys. The fabrication of bulk materials with ultrafine grain sizes has attracted a great deal of attention over the past two decades because of the materials' enhanced properties [ 1, 2]. In last decade a worldwide effort in manufacturing process to obtain ultrafine grain structures in steels is persisting."

Jan 1, 2011

By Mitsuru Tanahashi

In order to develop an effective process for the production of a solar-grade silicon (SOG-Si) from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at 1773 K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten MG-Si followed by oxygen gas injection into the melt (Two-stage connecting process). II) II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By Ye Chen, Jianhua Chen, Meng Liu, Yuqiong Li, Xiao Mu, Cuihua Zhao

"Sulfidization-amine is the most effective method for the recovery of smithsonite (ZnCO3), however the interface interaction details remain unclear. The sulfidization-amine flotation mechanism of smithsonite has been studied by Density Functional based Tight Binding (DFTB+) method in this paper. The slab model of ZnCO3 (101) surface was built and the adsorptions of a monolayer of HS- and S2- ions were conducted to model the sulfidization effect on the ZnCO3 (101) surface adsorption. DDA hardly interacts with the hydrated ZnCO3 (101) surface. Under the low concentration of Na2S, HS- ions form a Zn-SH-SH structure on the ZnCO3 (101) surface, which hinders the interaction between DDA and surface Zn atoms. Under the high concentration of Na2S, a layer of ZnS is formed on ZnCO3 (101) surface, which is favorable for the adsorption of DDA on the surface. This is consistent with the flotation practice where smithsonite flotation requires a large amount of sodium sulfide. The results could provide a microscopic investigation into the sulfidization-amine flotation mechanism of smithsonite.INTRODUCTIONSmithsonite (ZnCO3) is an important and typical oxide mineral of zinc. It is a semi-soluble salt mineral with a solubility product constant of 1.46 × 10-10 (Weast, 1973). The most common and effective method to recover oxidized zinc ores is froth flotation (Caproni et al., 1979; Pereia and Peres, 2005; Kashani and Rashchi, 2008). It is well known that the flotation of oxidized zinc minerals is much more difficult than the flotation of zinc sulphide minerals (Hosseini and Forssberg, 2007).The recovery of zinc oxide ores with poor floatability attracts more and more attention due to the depletion of easy-recovered of zinc sulfide ores.Sulfidization-amine flotation, which using Na2S as sufidizing agent and amine as collector (Mckenna et al., 1949; Rey, 1954; Abramov, 1961; Rey, 1979; Hosseini and Forssberg, 2007). This method is the most successful technology used for zinc oxide minerals flotation in large-scale industrial applications since it was invented in the 1950s (Önal et al., 2005; Pereira and Peres, 2005). There have been numerous experimental researches on the sulfidization-amine flotation of smithsonite. Shi et al., (2013) studied solution chemistry of smithsonite flotation system. Feng and Wen (2017) studied the formation of zinc sulfide species on smithsonite surfaces and its response to flotation performance. Wu et al., (2017) investigated the sulfidization behavior of smithsonite with the use of zeta potential, inductively coupled plasma (ICP), scanning electron microscope (SEM), and X-ray photoelectron spectroscopic (XPS). Their measurement results confirms the chemisorption of sulfur ions and the formation of ZnS film on the smithsonite surface after Na2S treatment, however the influence of HS- ions on the surface and the influence of sulfidization on the amine adsorption have not been discussed."

Jan 1, 2018

By N. K. Dumakor-Dupey, G. B. Sakyi-Addo, K. J. Bansah

"Artisanal and small-scale mining (ASM) occurs in many countries around the world, and provides a source of livelihood to many impoverished local people in areas where it occurs. This paper reports the role of female participants and reasons why they engage in ASM. Field visits were made to 12 ASM sites located in the Tarkwa Mining District of Ghana to conduct interviews with male diggers and female participants. It was observed that over 100 women between the ages of 18 and 50 participate in ASM for survival. They engage in ASM largely because they have no alternative employable skills and income sources. These female participants depend on ASM to sustain the lives of their dependents. INTRODUCTION Artisanal and small-scale mining (ASM) conventionally involves use of rudimentary tools (such as picks, shovels, chisels and hammers) to exploit precious minerals and metals from the ground. It has been a major source of livelihood to many impoverished local people for more than a century. In many instances, it is the only source of income to indigenous people who have no alternative employable skills. The World Bank estimated that more than 100 million people around the world benefit from ASM which largely occurs in developing countries in Asia, Africa, Oceania, and South and Central America (World Bank, 2013). Cobalt, which is used in lithium-ion batteries to power cellphones, laptop computers, and electric vehicles, is largely produced by artisanal miners in Congo (The Washington Post, 2016). In Sudan, ASM is a significant contributor to the national economy, accounting for about 85% of total gold extracted yearly from 2010 to 2015 (Ibrahim, 2015). Also, according to the Embassy of Sierra Leone in Washington DC, USA, 90% of mineral export in Sierra Leone can be attributed to thriving artisanal diamond mining in the country (Sierra Leone Embassy, 2016). In Ghana, the ASM sector was recognized by government as a multimillion industrial activity, and through a series of initiatives, it was legalized by promulgating the Small Scale Gold Mining Law of 1989 (PNDCL 218). Presently, artisanal mining is widely practiced in two forms: licensed (registered), sometimes referred to as formal ASM, and unregistered (informal or illegal) operations, popularly called “galamsey”, a name believed to have been derived from “gather and sell” by ancient miners who could not communicate in the English language with European/British miners. The ASM sector in Ghana, like other countries, has seen a rise in female participation over the years. A report by the International Labour Organization (ILO) indicated that women account for about 15% of total workforce in ASM in Ghana, and up to 50% in Africa (ILO, 1999). Other researchers have also estimated women participants in ASM to be between 30 and 70% in Africa (Hinton et al., 2003a; Hinton et al. 2003b; Hilson, 2002). Presently, there is no reliable data from Ghanaian authorities on number of females engaged in ASM. However, data obtained from 15 ASM sites suggest that at least 40% of the employees are women. It is expected that a similar trend exists across ASM operations in Ghana."

Jan 1, 2017

By F. W. Mueller

It seems to be a matter of general understnading that title extraction or use of ground water may not be used as the basis of a depletion deduction under the United States Revenue Code And indeed, I have been unable to find any precedent upon which to base such a deduction. It is for this reason that the Shurbet case, which is the subject of my discussion and is now before the Court, may well become a precedent as authority for the allowance or disallowance of a depletion deduction for income purposes. It is well known that the law recognized that capital is consumed in the process of extracting minerals, oil and has, other natural deposits, and timber (underscoring supplied). This exhaustion, or depletion, is likened to the using up of raw materials in manufacturing. The law, therefore, provides a deduction for depletion which is intended as compensation for the exhaustion of assets consumed in the production of income through severance of minerals, oil and gas, other natural deposits, and timber.

Jan 1, 1962

By R. J. Gochin, P. Bevilacqua, G. D. Schena

This class of flowsheet-dependent simulators does not replace modular simulators, such as Modsim and Microsim, which are necessary for the assessment of different flowsheets before selection of the most desirable technical option and for investigation of the fine details of unit processes. The system presented here is regarded as complementary, serving in the early stages of feasibility studies as an aid to assessing the convenience and economics of preconcentration; the example used is of dense-medium preconcentration of a barytes-fluorite ore

Jun 13, 1905

By J Ding, H J Peng, S B. Zhu, L Hou, J R. Zhang, S Y. Wu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Numerous Fe-Cu-Au-rare earth element (REE) deposits have been identified within the Palaeoproterozoic Dongchuan Group of the Kangdian region of SW China. Geochronologic and geochemical data of the dolerite dykes and other volcanic rocks reveal extensional activity occurred about 1.7 Ga called ‘Kunyang Rifting’. The Kangdian region underwent variable degrees of extension, meaning that breakup in the central part of this region occurred earlier than in the north. Research on microphysiography, isotopic geochemistry and inclusions of the Yinachang typical Fe-Cu-Au-REE deposits suggest that the dominant mineralisation fluid is high-temperature, high-salinity magma fluid, containing alkalic components, volatile phase and Cu-Au. Metasomatism and mixing between this magmatic fluid and carbonaceous wall rock and meteoric water caused the precipitation of Fe, REEs and Cu-Au. A chalcopyrite Re-Os age from the Yinachang deposit obtained during this study is some 50–100 million years younger than the timing of emplacement of the deeply sourced Haizi and Dongchuan dolerites. The Yinachang deposit is a typical iron oxide-copper-gold (IOCG)-type deposit, and the presence of this and other deposits in the Kangdian region indicates that the region hosts an intraplate extension-related IOCG system within the western edge of the Yangtze Block, China.CITATION:Hou, L, Ding, J, Zhang, J R, Zhu, S B, Wu, S Y and Peng, H J, 2015. Proterozoic iron oxide-copper-gold mineralisation in the Kangdian Region, south-west Yangtze block, China – a case study on the Yinachang Fe-Cu-Au-rare earth element deposit , in Proceedings PACRIM 2015 Congress, pp 255–264 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Steven M. Puricelli

In recent times, smelter off gases treatment plants have become more efficient and environmentally friendly. Where in the past it was acceptable to process only high strength, treatable furnace gases, new smelters must now treat primary gases and abate dust and SO2 from secondary gases: Processing smelter gases can present some interesting challenges. Some equipment can see varying concentrations of sulfuric acid, up to the boiling point, with a periodic table of contaminates thrown in for good measure. Treating weaker secondary gases have, in the past, been cost prohibitive. Nowadays, new technology, like physical absorption or catalytic carbon, show promise for economically treating low strength secondary gases. Modem smelters do a much better job of treating the SO2 laden gases generated by the smelting process but significant challenges remain.

Jan 1, 1998