Search Documents

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By J. H. Corrigan

A series of six papers describing the Falconbridge Dominicana Ferronickel project were presented at the International Laterite Symposium held as a joint project of TMS-AIME in February 1979 at New Orleans. A review of the ore mineralogy, as well as. the processing and environmental practices as they exist today at Falcondo with emphasis on modifications put into practice since 1979 are presented in two papers: Part I.- Mineralogy and Ore Dressing E.W. Lithgow - General Superintendent ? Mines Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, X- ray amorphous materials. Minor constituents are hematite, gibsite, olivine and enstatite. In the Ore Dressing plant, the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock kagments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing. Part II.- Pyrometallurgy, Fuel and Power Generation J.H. Comgan - Manager ? Production Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Falcondo&apos;s energy requirements are based on oil which is refined on site to provide distillate to carry out drying and selective reduction of the nickeliferous ore in the shaft furnaces, plus bunker oil to produce electrical power for process melting, refining and ancillary use. The dryer product at 1.68% Ni is briquetted and passed counter current to hot reducing gas in 12 vertical shaft furnaces. The hot calcine discharge is melted in two high power electric furnaces at very high secondary voltage. The crude ferronickel is ladle refined and cast as 15 kg ingots or 125 gm ferrocones.

Jan 1, 1993

By W. M. Goodwin

The gold district of northwestern Quebec, though it has attracted such widespread attention during the past year, is still in the prospect stage throughout, and one must preface any remarks about it with the plain statement that its capacity to produce gold commercially is still subject to proof. However, this proof may be forthcoming any day, and from widely separated localities. Consequently it is of interest to note some of the features of the region and of the prospects now being developed. First I shall note the relation of this mining development to the province of Quebec and to the Dominion; then will follow a brief resume of the known geological facts; and finally I shall describe briefly some of the more advanced prospects developed during the past twelve-month. Those that have followed closely the fortunes of the new gold-field will find little that is new in what follows, but it may serve a useful purpose for others by bringing together scattered items of information and presenting them as a whole. GOLD MINING AND AGRICULTURE First let us consider the gold belt in its relation to the province of Quebec. Apart from the world-renowned asbestos camp south of the St. Lawrence, it is the only mineral development of major importance the province has experienced. It is the first important development in the province&apos;s vast area of Precambrian rocks, most of which remains as yet totally unexplored and unprospected. The relative importance of this first mining camp in northern Quebec cannot as yet be gauged, but it is bound to stimulate an active interest in the other mineral-bearing areas now known to exist, and in the vast unexplored spaces.

Jan 1, 1924

By J. Grubb

"The undertakings described in the paper titled “Study on correlation of quantified coal rank with self-heating temperature” by Wang and Luo in the November 2015 issue of Mining Engineering (Wang and Luo, 2015) are mathematically sustainable and an acceptable extension of work performed by Smith and Lazzara (1987) for the U.S. Bureau of Mines. The paper is not an accurate explanation of the currently accepted leading practice for determining the propensity of a coal seam for spontaneous combustion. The paper could lead a practitioner to an oversimplified conclusion on how to determine the propensity of a coal seam to spontaneously combust.The spontaneous combustion of coal is a complex and not fully understood reaction. What is understood is that many more factors other than selfheating temperature (SHT) and coal rank are required to sufficiently evaluate the risk of spontaneous combustion in a particular coal seam. A superficial assessment can lead to an improper response to the risk. Some statements on the next steps through an appropriate literature search would have made the authors’ conclusions more credible.The SponCom 2.0 software, updated by the National Institute for Occupational Health and Safety (NIOSH) in 2011, provides a path for evaluating the susceptibility of a coal seam to spontaneous combustion. In addition to proximate and ultimate analyses to establish coal rank, and therefore an estimate of SHT, the program includes the history of heatings, friability, seam thickness, overburden thickness, rider seam presence, pyrite presence, face and butt cleat densities, geothermal source presence and other geological features in the assessment. Mining conditions including floor heave, rib sloughage and rate of advance are also assessed to conclude a propensity for spontaneous combustion."

Jun 1, 2016

By Hsing Kuang Lin

Ferric chloride leaching w.as applied to a complex sulfide ore from Tok, Alaska to dissolve zinc, lead, silver and copper. Gold in the leaching residue, as well as in the ore, is found to be refractory to the conventional cyanidation process. Roasting, pressure oxidation and elemental sulfur removal followed by cyanidation were tested to improve gold dissolution. Also tested were thiourea leaching and high-pressure cyanidation. The readsorption of dissolved gold by carbonaceous matter in the chloride leaching residue was analyzed. Based on the experimental results, factors causing difficulty of gold dissolution from the leaching residue are discussed.

Jan 1, 1989

By Harry W. Campbell

In 1986 at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 2 acre North Sisters Rocks Wilderness Study Area (OR-12-8) in order to evaluate its identified mineral resources. The Wilderness Study Area is located in Curry County, Oregon, about 15 miles north from Gold Beach. No mines, prospects, or mining claims were located inside the study area, and no mineral resources were identified. Stone from the study area could be quarried and used for construction purposes; however, two nearby quarries have sufficient stone to satisfy local construction needs. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and mineral resource potential of the North Sisters Rocks WSA (Wilderness Study Area) 1/ at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of investigations will be used to help determine the suitability of the North Sisters Rocks WSA for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1987

By R G. Jeffrey

The Northparkes, Endeavour 26 orebody is a porphyry copperûgold deposit and comprises a moderately to well jointed rock mass characterised by gypsum veining, the intensity of which decreases with depth. The top 480 metres of the orebody is currently being mined by block caving, the undercut dimensions measuring 196 metres in length by 180 metres in width. Continuous caving was never achieved after the completion of the undercut thus cave inducement techniques were sought to maintain caving so as to safely sustain production. The use of hydraulic fracturing as a cave inducement tool was successfully trialled in December 1997 using existing exploration boreholes located midway up the current lift. Subsequent fracturing campaigns have enjoyed various degrees of success and have yielded in excess of seven million tonnes of ore at a significantly lower cost than conventional cave inducement techniques. Monitoring of both the hydraulic fracture system and the rock mass response has provided considerable insight into the geometry, growth and influence of hydraulic fracture networks above the Northparkes block cave, and has initiated additional research into the use of hydraulic fracturing in other mining methods.

Jan 1, 2000

By V. J. Ramirez, A. M. E. Noguez, M. J. Navarrete, B. G. Salas, N. T. Robert

"The close die forging stress in truncated conical cavities is evaluated with dimensional analysis. Five dimensionless groups are proposed from the process variables in order to simplify the forging stress determination. These groups are experimentally related and graphically expressed. This methodology can be used to predict the actual forging stress in industrial close die forgingThe use of the dimensionless groups allow to comprise more cases than the presented here, provided similar geometries and operational conditions.Introduction.Closed die forging is essentially a plastic deformation inside a two piece mold (forging die) with the inverted shape of the actual forging geometry. This plastic deformation will always be the result of a compressive stress. There are theoretical models which include complex calculations for the analytical determination of stresses (1, 2, 3, 4). Results of these calculations are approximate, requiring generally ulterior tests to obtain the true operational conditions(5).In this paper, it is presented a simplified approach to the actual compression stress needed in the forging. A well known tool in engineering: the Buckingham's Pi theorem in conjunction with dimensionless groups and a working piece scale model is used. Dimensional analysis will give the dimensionless terms needed to experiment with a selected scale model geometry to make the stress determination. The results presented demonstrate the reliability of this methodology."

Jan 1, 1997

By J. S. S. Allwin Ebinesar

The bioremediation of zinc was carried out using Pseudomonas alcaligenes, a Gram negative heterotroph. The parameters such as pH, bacterial cell number, initial metal concentration, and interaction time on the biosorption of zinc were studied. The maximum zinc uptake was found to be about 95% at pH 5 and biomass loading of 2.7x1010cells/mL. The biosorption isotherm for zinc exhibited Langmuirian behavior and the Gibbs free energy of biosorption was determined to be -31.2 kJ/mol, indicative of coordination of zinc with the functional groups on the bacterial surface. The adsorption kinetics followed a pseudo-second order equation. FTIR and EDAX studies confirmed the interaction of zinc with the biomass. The mechanisms of metal-microbe interactions are discussed.

Sep 1, 2012

By Gerald Onyedika, Tochi Onwumere, Martin Ogwuegbu

"The kinetic study for the leaching of iron from cassiterite ore in KOH solution was studied. The effects of KOH concentration, particle size and reaction temperature on the leaching rate of iron were also examined. The results of leaching studies showed that the leaching of iron from cassiterite ore in KOH solution is significantly influenced by the reaction temperature, KOH concentration, and decrease in particle size. The study showed that 90.62% of iron ore was leached in 8M KOH solution at 80°C within 120 minutes. The experimental data were well evaluated using the shrinking model for surface chemical reaction and diffusion control through the product layer. The activation energies for the iron ore dissolution using the two models were calculated to be 32.06KJmor1 and 97.97 KJmor' respectively.IntroductionIn recent times, there has been increasing attention on the kinetic study of mineral dissolution. In most of these studies, the experimental results were analyzed with a suitable shrinking core model under the assumption that the ore is a homogeneous spherical solid phase [1-4]. A study of the dissolution kinetics of a Nigerian cassiterite ore by hydrochloric acid showed that increase in the hydrochloric acid concentration is accompanied with increase in the amount of cassiterite ore dissolved at various times [4]. The optimal concentration was found to be 4.0M HCl, after which there was a decline in the amount of the ore dissolved, which showed that the concentration of the reagent has a significant effect on the leaching rate of the ore. Also in studying the effect of stirring speed on the rate of cassiterite ore dissolution while keeping other conditions constant for 120 minutes, the result showed that the rate of cassiterite ore dissolution was dependent on the stirring speed over a range of 0 to 630 rpm. Above 360 rpm, the stirring speed no longer had any effect on the solid dissolution. The dissolution rates of cassiterite were analyzed using a suitable shrinking model. The results showed that the reaction was controlled by the diffusion of tin through the porous product layer, a reaction order with respect to hydrogen ion concentration of 0.92 M and activation energy of 50.05KJmor'. In another kinetic study on the leaching of a low grade niobium-tantalum ore with concentrated KOH solution the effect ofreaction temperature, KOH concentration, agitation speed, particle size and alkali-to-ore mass ratio on the dissolution rate of niobium were examined [5]. The result of niobium leaching from low grade niobium-tantalum ore with concentrated KOH, solution at different agitation speeds showed that the dissolution rate increased with increase in agitation rate. In the case of particle size effect, the results show that small particles require much shorter time for complete dissolution than the large ones."

Jan 1, 2013

By L. G. Austin

A program has been written to combine the Klimpel-Austin approximate model for liberation in a binary system with a mill model applicable to ball milling. The model applies for a system where the volume fraction of valuable B in host matrix A is small. The mill model is treated as an equivalent series of fully-mixed reactors. Twenty-three classes of material are considered: pure A; pure B; unchanged AB; 0-10.2 B in AB either as surfac- exposed B or as wholly-contained grains of B; 10-20% B in AB, surface-exposed or wholly- contained;etc.. to 90-100% /b ub /ABm syrface-exposed or wholly-contained. Illustrative cases are given making reasonable assumptions concerning relative rates of breakage and primary breakage distribution functions for each class of material.

Jan 1, 1986

By M. N. Collison

"In 1960, with the opening of the Chisel Lake mine near Snow Lake, Manitoba, the Hudson Bay Mining and Smelting Co., Limited, commenced a new phase in their mining operation -that of bringing ore to Flin Flon over 100 miles of railroad.The schedule of operations required to accomplish this, together with an outline of some of the problems of handling ore at 40° and 50,0 below zero, are discussed. The facilities required to thaw and unload from twenty to fifty cars per working day are also described."

Jan 1, 1966

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines showed that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum group metals (PGM) was technically feasible. This work involves a more detailed investigation of the chemistry of the dissolution of PGM in cyanide solutions. The PGM species in solution identified by ultraviolet spectroscopy. Pt and Pd cyanide complexes were square were The planar in geometry, while the Rh complex was octahedral. The rate of dissolution of the PGM was also investigated using a rotating disk technique. Dissolution rates increased in the order of Rh, pt, and Pd, respectively.

Jan 1, 1994

By John F. Slonaker

This report is a review of current research being conducted in the United States which is intended to increase the utilization of coal ash. In order that this report be as timely as possible, the majority of information was obtained by direct comunication with the people listed in the references. Due to the magnitude of the flyash research program, some projects may be inadvertently omitted. Field research on flyash for use as an agricultural fertilizer is being monitored at Virginia Polytechnic Institute and State University.1 This research is directed at determining the plant nutrients that are available in flyash as well as the quantities of flyash that can be applied to agricultural soil without adversely affecting plant growth, Coal mine spoil and refuse bank reclamation with power plant flyash is being demonstrated by United States Bureau of Mines, Morgantown, West Virginia.2 Numerous highly visible coal refuse piles and strip mine spoil banks contribute to air, water, and land environmental problems. Revegetation of several experimental sites with flyash from bituminous coal-fired power plants was undertaken in West Virginia and Pennsylvania. Conventional farm equipment was used at some of the sites while large earthmovers were required at others. The flyash served as a neutralizing agent, dilutent, and soil amendment to provide some nutrients which enhanced vegetation of the barren areas, Estimated cost of reclamation by this method is $300.00 per acre of previously leveled area. This figure can vary considerably depending upon the topography of the site, haul distance, quality of the soil and quality of flyash.

Jan 1, 1974

By E. Kaya

Investigations of fine grinding of bituminous coal in a laboratory-scale pulverizer are described. The results indicate essentially "normal" breakage behavior at relatively coarse sizes (greater than about 20 µm) but show clear evidence for re-agglomeration in the fine size range (less than about 10 µm). A simplified population balance model for simultaneous growth and breakage has been formulated. Breakage rates and breakage distributions are assumed to follow the patterns typically observed in simple grinding systems. It is recognized, however, that solid particles and agglomerates may exhibit different breakage behavior. Agglomeration rates are assumed to be determined by contact probability, i.e. by the relative numbers of interacting particles. Based on comparisons of model simulations and experimental data, it appears that agglomerate re-breakage rates and fragment size distributions are quite different from those for solid particles. The result is that product size passes through a minimum and then increases with time as agglomeration begins to dominate.

Jan 1, 1996

By T. S. Golosinski

Use of contractors to excavate, load and haul mined material is widespread in Australia. It is also becoming a common practice in many other countries. The paper reviews current practices in Australian contract mining. Various types of contracts are reviewed, including partnering arrangements and alliancing between the contractor and the mine owner. Applicability of various types of contracts to specific mining situations is discussed, as is their impact on overall mine performance

Jan 1, 1998

By John S. Dunning

This is one of a. series of papers being prepared for and published by the United States Bureau of Mines, describing raining and milling methods at crushed-stone plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might in man; instances cause embarrassment to individual producers as well as to the industry as a whole. However, operating costs are essential to technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that the scope of the cost tabulations shall not be misunderstood. This paper deals with the quarrying and crushing methods used at the Avon Mountain trap-rock quarry of the Atlas Sand, Gravel & Stone Co., in West Hartford, Conn.

Jan 1, 1936

By O. E. Omotoso

This study is part of an ongoing investigation to understand the mechanism of stabilization/solidification of hazardous chromium wastes in ordinary Portland cement (OPC). Tricalcium silicate (C3S*),a major component of OPC is mixed with reagent grade Cr(lll) and Cr(VI) solutions, to simulate complex cementiCr waste systems. Scanning electron microscopy (SEM) and energy disperse spectrometry (EDS) were employed to provide microstructural and chemical information. Transmission electron microscopy (TEMlEDS), apart from complimenting the SEM, was used to probe the distribution of Cr in the hydration products of C3S and to provide crystallographic information. 29Si MAS NMR (magic angle spinning - nuclear magnetic resonance) Was used to characterize the influence of Cr on the hydrated silicate structure.

Jan 1, 1995

By R. Kobialka

In the article results of experiments over jaws? linings in jaw crushers with different shaping of working surface were presented. Following sets of jaws were under investigation: immobile plain jaw and moving jaw with grooving surface. Grooving jaws have groves with circular, triangular and trapezoid cross section. In order to evaluate efficiency of comminution both the grain composition of product and the content of irregular grains were determined, as well as the size of crushing forces and process efficiency were measured. For the combination: plain jaw with grooved one, a good results were obtained as regards the grain composition of product and the content of irregular grains. Crushing forces were higher at crushing with mixed types of jaws (the one plain, the second grooved), in comparison to crushing with using both grooved jaws. Efficiency of the process was definitely higher for mixed jaws.

Jan 1, 2014

By Bruce W. King, David A. Newman

"Underground mines have always been an integral part of the limestone industry. However, beginning in the 1990s, the number of underground limestone mines has increased for many reasons including• Stripping ratios at surface quarries have become uneconomic.• Existing surface quarries have reached the mineral boundaries, and the remaining stone reserves are underground.• Surface access to the entirety of the limestone reserve is limited by development or infrastructure.• The once-rural setting of the surface quarry is now surrounded by subdivisions and development. An underground mine is less intrusive and takes the mining operation out of the public eye.• For larger markets, an underground mine enables year-round production without the sequence of overburden stripping in the winter to expose mineable stone for summer production. This is common at many surface quarries.Multiple-level operations are a natural extension of the decision to mine underground. Most limestone reserves, for example, the Tyrone-Oregon-Camp Nelson, Hermitage-CartersLebanon- Ridley, and Salem Limestones, are sufficiently thick to accommodate multiple levels. Multiple-level mines should be planned by considering each level separately and then integrating the individual levels into a larger mine plan. Failure to plan all the levels of a multiple-level mine in concert can result in ground control (back, pillar, floor, and inter-level sill pillar) problems attributable to stress transfer and interaction between the levels or the necessity to leave a thicker sill pillar between adjacent levels.Multiple-level mine planning begins with geology. Once the upper level back horizon is identified, the geology, rock strength, and physical properties in each level are used to• identify the optimal back horizon• quantify whether back support is required and, if so, the type, spacing, and length of the back support• determine the pillar centers• determine the total mining height, including floor shots"

Jan 1, 2016