Search Documents

By Charles H. Rawlins

Reported is work done on processing of steel mill effluents in the areas of dewatering and separation. Much of the waste from these operations is in the form of sludges from scrubbers, in which the primary constituent is iron oxide. Recycling of the sludge&apos;s magnetic fraction has become economically attractive in order to reduce the overall volume placed in landfills. The objective of this research is to determine the effectiveness of combining magnetic and cyclonic forces, to recover iron oxide particles from waste water stream, while decreasing the volume to be disposed. Three different size hydrocyclones, operating within the field of a quadripole magnet, were tested using varying feed pulp densities of magnetite, magnetite/dolomite, blast furnace (BF), and basic oxygen furnace (BOF) slurries. In the first three cases, the percentage of magnetics recovered increased to greater than 95%. The limiting operational factors are; high pulp density for small cyclones, which can cause flow blockage within the magnet field, and extremely fine particle sizes (<2 microns), which cannot be recovered. The results indicate this technique can remove virtually all the magnetic particles from some steel effluents to a 40-50% weight percent solids pulp, on an in line continuous basis.

Jan 1, 1994

By K. P. Chong

Fracture toughness of oil shale is an essential property in fragmentation to optimize particle sizes and permeability distributions in in-situ processes. Fracture mechanics of oil shale has been based on conventional fracture mechanics using notched samples and assuming the material to be isotropic and elastic. Oil shale is a layered material more accurately characterized as transversely isotropic. The senior author proposes to use a semi- circular core specimen with a center crack subjected to three point bending. Singular crack tip elements with isoparametric elements are used. The precracked semi-circular disk is modeled under displacement loading. The effect of crack length on the non-dimensionalized stress intensity factor is investigated by strain energy method, ellipse method, and stress method. Very close agreements are found. The fracture toughness is obtained by compressing the specimen in to failure. Parameters such as oil yield are investigated.

Jan 1, 1984

By D P. Sainsbury, J Western, B L. Sainsbury, V Mutton, P E. Petrie

Remnant rib pillars at Castlemaine Goldfields Ltd’s Ballarat Gold Project have been sterilised by the placement of loose rock fill in production stopes. The application of selectively injecting low-viscosity grout into the backfilled stopes to form a stabilised material has enabled recovery of the previously sterilised pillars. This paper outlines the engineering design, quality control and quality assurance program implemented to ensure the safe and efficient recovery of the rib pillars. The successful program included laboratory testing, numerical exposure stability modelling and in situ monitoring.CITATION:Sainsbury, B L, Sainsbury, D P, Western, J, Petrie, P E and Mutton, V, 2014. Pillar recovery adjacent to stabilised rock fill at the Ballarat Gold Project, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 77–86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Harry R. Nicholls

Preliminary tests on presplitting rock in the presence of an in situ static stress field were undertaken to study the influence of a horizontal static stress field on the creation of a vertical presplit fracture plane. These tests indicated that it is easier to fracture the rock parallel to the in situ maximum compressive stress than in other directions. Instrumented shots indicate that the interaction of stress waves generated by the detonating charges is probably responsible for starting tensile fractures between shotholes and that expanding gases may propagate these initial cracks by a wedging action. The hole spacing for presplitting appears to be equal to the half wavelength of the stress wave. However, wider hole spacing appears feasible if the initial fracture is started by closer hole spacing.

Jan 1, 1966

By P. Koskinen

Outokumpu Oy has 30 years&apos; experience in nickel production. It is mainly based on the technology developed within the company. The production chain starts from the mines reaching to the high-grade cathode nickel and the stainless steel manufacturing. As a multi-metal producer Outokumpu has the advantage to exploit from nickel raw materials also other valuable metals and intermediate products which can be processed at the company&apos;s various plants. The main source of nickel concentrate is nowadays the Enonkoski Mine started up in early 1986. It is the most modern mine in Finland being provided with the latest Finnish high-tech systems. Nickel concentrates are smelted at the Harjavalta Works using Outokumpu&apos;s internationally well-known flash smelting method. Also nickel containing residues and secondaries&apos; are used as raw materials. The high-grade nickel matte from the smelter is then refined at the nickel refinery in a hydrometallurgical process, which was also developed by the company&apos;s own research staff. These processes have been continually improved and capacities gradually enlarged to 18 000 mtpy of cathode nickel. Besides plating, melting and superalloying purposes part of the nickel ends in stainless steel at the Tornio Works. The production was started in 1976 and has reached an established position on the European market.

Jan 1, 1988

By L. A. Haas

The Bureau of Mines conducted bench-scale leaching tests with recycled spent copper electrolytes and copper-nickel mattes produced from the Minnesota Duluth Complex concentrates. This report describes the first stage of an overall two-stage leach operation. The objective of this research was to determine the matte-leach technology required to convert spent copper electrolyte into an enriched nickel liquor suitable for a nickel refinery and there-fore essentially free of copper, iron, and sulfuric acid. The experimental variables investigated were matte composition, particle size, spent electrolyte content, pulp concentration, oxygenation, temperature, and time. The time required to produce an enriched purified nickel liquor decreased with increasing pulp concentration, temperature, and oxygenation, but increased with increasing particle size and electrolyte copper and acid content. Nickel-rich (about 50 g/l) liquors at a pH of about 4 and containing less than 1 g/l of copper and iron were produced at 70° C by leaching minus 325-mesh low-iron (less than 5 pct) matte for 8 hours with spent electrolyte containing 22.4 g/l Cu, 28.9 g/l Ni, less than 0.1 g/l Fe, and 50 g/l H2S04 at a pulp concentration of 1 kg of matte per liter of spent electrolyteo Varying the nickel content of the spent electrolyte from 11 to 101 g/l appeared to have no appreciable influence on the matte leaching characteristics.

Jan 1, 1981

By S. M. Fatemi-Varzaneh

The AZ31 magnesium alloy is considered as a promising alloy in various applications and industries. Furthermore, to design a proper hot working process (rolling, forging and extrusion), the assessment of hot working behaviour of the alloy is necessitated. Accordingly, the hot deformation behaviour of AZ31 alloy was studied through hot compression testing method. The latter was carried out in a wide range of temperature (523 K to 783 K) and strain rates. The obtained true stress-true strain curves and final microstructures were examined and a partial melting was realized at 740 K. It was concluded that the presence of liquid did change the deformation mechanisms thereby affecting the flow behaviour.

Jan 1, 2005

By M. J. Sapko

The U.S. Bureau of Mines has developed a portable meter for measuring the component concentrations in binary dust mixtures whose constituents have different optical reflectivities. The meter has been successfully tested with coal dust-rock dust mixtures taken from coal mines in Europe and the United States and fluorinated-carbon mixtures that change from carbon black to pure white during fluorination. Additional study has also substantiated the theoretical expressions used in the design of the meter.

Jan 1, 2010

By Krishna Parameswaran

This paper discusses sustainability considerations in primary copper smelting using selected examples of practices at ASARCO LLC, an integrated U.S. primary copper producer. Using the classic Brundtland Commission definition of sustainable development, i.e., “development that meets the needs of the present without compromising the ability of future generations to meet their own needs,” the paper discusses how copper mining and smelting practices can be made sustainable. The examples used to illustrate sustainability considerations include: (1) adoption of flash smelting; (2) emission reduction and process improvement associated with anode refining of blister copper and the converter retrofit project, and (3) preliminary research findings on alkali treatment of copper smelting slags and copper mine tailings.

By R Badreddine, J Rose, L De Windt, P Chaurand, L Raimbault

Municipal solid waste of incineration (MSWI) bottom ashes are recycled as aggregates in civil engineering. These heterogeneous materials are composed of crystalline and glassy solid phases which contain trace metals, presenting a potential risk to the environment. Secondary ion mass spectrometry (SIMS) can provide quantitative chemical information, in particular the localisation of metals at trace level. Unstable glassy phases formed during incineration are present in relatively high proportions. Their analyses suggest a continuum between melilite-bearing glasses and dark glasses enriched in iron with abundant spinel aggregates. These primary glasses are enriched in zinc (~4500 ppm) but depleted in lead (~800 ppm) by comparison with the bulk chemical composition and reference materials. Heterogeneous cementing and encrusting admixtures on coarse grains are studied in a second step. SIMS imaging suggests a superposition of band zones including an intermediate layer enriched in iron oxyhydroxides and a superficial layer with calcium accumulation. A strong spatial association between lead and iron is systematically observed. Extended X-ray absorption fine structure (EXAFS) supports these observations by demonstrating that lead co-precipitation within iron oxyhydroxides, or sorption on their surfaces, may be a main containment process in the cementing and encrusting admixtures, whereas lead speciation is globally more complex in MSWI bottom ash.

Jan 1, 2008

By Greg Dowling, Jun Ge, George Shannon, Shufeng Yang, Yongfeng Chen, Lifeng Zhang

"Inclusions in 316L stainless steel ingots poured using two different upgate designs – a traditional upgate and a swirl upgate - were investigated using SEM and ASPEX automated inclusion analysis. The main inclusions were high SiO2 inclusions, MnS inclusions and SiO2-Al2O3-CaO inclusions. More inclusions were detected at the top of the ingot than other places in vertical direction, and more inclusions were at the edge of the ingot than other place in the radial direction. With swirling upgate there were more K- and Na- bearing inclusions than that with the traditional upgate indicating possible more serious flux entrainment with the swirl upgate.IntroductionIngot casting still is very important for production of special steel grades including high carbon chromium bearing steel, thick plate, seamless tube, forgings, bars, and wire rods [1] . During the bottom teeming process, molten steel enters the trumpet and passes through the spider into the runners. Molten steel then enters the ingot mold through an upgate near the end of the runner. In the early stages of filling a mold, a mold flux bag hung in the mold were burnt and the mold flux will cover the top of the rising steel to protect the steel from being reoxidized, acting as well as act as a thermal insulator. So far, some efforts on studying inclusions characteristics in the ingot have been reported. A review paper on the control of inclusions during steel ingot casting was published by Zhang et al. [2] Zhang also studied Inclusions in bottom-teemed ingots of plain carbon steel and found that the >20µm inclusions originated from either the entrainment of mold flux of the reoxidation during teeming process. [3] The results of Nagendra and Du showed that there were more inclusions in the centre part of the ingot [4]. Eriksson et al reported that the composition of inclusions was more complex in the mold samples in comparison to the ladle samples, and more inclusions in the mold were found than in ladle because of the reaction between the mold flux and the molten steel [5]. It was reported that SiO2-CaO-Al2O3 inclusions originating from mold powder with reoxidation product Al2O3 as a part, and there were more inclusions close to the side wall than the center of the ingot in the radial direction. [6]. A more recent investigation showed that four main types of inclusions in runner samples were classified: oxides, sulfides, complex and carbon-nitrides. [7] The flow pattern in the mold during filling has been found to be an important factor regarding inclusions in the ingot. In the early stages offilling a mold, steel enters the mold through the entry nozzle at a high velocity. The effect of the resulting turbulence on the meniscus can lead to the entrainment of mold flux. Efforts have been paid over the years to find methods to reduce the velocity of the molten steel entering the mold, such as using opening angle of the inlet nozzle [8], using swirl blade at the runner [9], using a divergent nozzle combined with a swirling flow generated in the nozzle [10-11]."

Jan 1, 2012

By Amy Anderson

The Silica (SME) Technology has been utilized on three separate projects focusing upon the stabilization of mercury-contaminated materials: at the Mother Lode Mine in Oregon, the Sulfur Bank Mercury Mine in California and at a former chloralkali plant in British Columbia. Each of the projects relied primarily on the results collected via EPA Method 1311 TCLP, with additional tests such as SPLP, humidity cell tests and other supporting tests employed as well. Both technical and economic performance of the silica-based technology was evaluated as well as that of competing technologies in some cases. Results established that in each of the three projects an SME chemical dosage rate of 3% chemical by weight of soil/sludge was the optimal ratio required to achieve project treatment objectives, TCLP test results exhibited a reduction in the leachable mercury from the treated materials ranging between 75% and 99% as compared to untreated material, satisfying the technical objectives for each project, Project costs ranged from $l5.00 - $18.26 per metric ton.

Jan 1, 2003

By C. Doyle, J. Brennan, C. Díaz, J. Hrepic, K. Cushnie

"In 1991/1992, INCO undertook a successful R&D program aimed at extending the lining lives of the top blown rotary converters (TBRCs)at its Copper Cliff Nickel Refinery (CCNR) and the electric furnace at INMETCO. At the laboratory scale, this effort was divided into three phases. In the first part, mineralogical work was performed on six refractories that were either currently being used to line these vessels or were considered suitable alternatives. In the second part, this mineralogical knowledge was used to help determine the compositions of slags that would not corrode the bricks at the operating temperature (1600°C) of the above furnaces. Finally, several important properties of the six refractories were measured to complete their evaluation as candidate linings. This paper reports the results of all three phases of the laboratory scale R&D work.The mineralogical work showed that rebonded fused grain magnesite-chrome (RFG-MC) bricks consist principally of periclase with minor amounts of free chromite and trace quantities of silicates monticellite and sometimes olivine. The bricks are principally held together by periclase-periclase direct bonding. Of note, the bulk of the chromite exists as exsolved precipitated blebs within the periclase grains. These likely redissolve at high temperature.Slags on the periclase liquidus coexist stably with these refractories. Examples are presented using CaO-MgO-Al2O3-SiO2 slags at~1600°C.Finally, the two refractories manufactured using close to 100% fused grain material generally outperformed the others in terms of physical properties and certainly were superior in their resistance to slag penetration damage."

Jan 1, 1997

By O Ishiyama, L Lu

Sintering is the most economic and widely used agglomeration process to prepare iron ore fines for blast furnace use. Due to the depleting reserves of traditional high-grade iron ore, there have been considerable changes in iron ore resources available throughout the world, especially in steel mills in East Asia. Corresponding to the changes in the availability of iron ore resources, the amount of impurities in iron ore has been slowly increasing. Some of these impurities have been found to have deleterious impacts on sinter quality and sintering performance. In the meantime, an increasing number of large blast furnaces with inner volumes of more than 5000 m3 have been built that require more sinter and are often more demanding in terms of the quality requirements of the ferrous materials. Finally, sinter plants are facing increasing pressure due to more stringent regulations regarding their environmental impact. This paper gives an overall review of a variety of technologies developed worldwide to tackle the changing raw material characteristics and mitigate emissions from sintering operations.CITATION:Lu, L and Ishiyama, O, 2015. Recent advances in iron ore sintering, in Proceedings Iron Ore 2015, pp 61–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Farid Mirahadi

Forecasting productivity of construction operations is a difficult but crucial task in planning construction projects. Over the past decades, many models have been developed to forecast productivity for different construction operations. Models made up of several functional relations and controlled by a specific number of control rules are more in line with human reasoning and logic. Neural-Network-Driven Fuzzy Reasoning (NNDFR) structure as one of these models shows a great performance for modeling datasets among which clear clusters are recognizable. Lack of the compatibility of conventional NNDFR with fuzzy clustering algorithms besides the insufficient attention paid to the optimization of number of clusters in this model, created a potential area for further research. The main contribution of the proposed model is to develop a modified NNDFR system to model construction data. To this end, Fuzzy C-Means (FCM) algorithm is substituted for K-means in NNDFR structure, and its parameters such as the number of clusters and weighting exponent are optimized through genetic algorithm. The proposed model is further verified through simulation of a construction operation in which several qualitative and quantitative factors are considered. Its implementation to the case study shows a considerable improvement of model performance with lower Mean Squared Error (MSE). The developed model assists researchers and practitioners in utilizing historical construction data to forecast productivity of construction operations with a high accuracy that could not be obtained by traditional techniques.

Aug 1, 2013

By O. P. Hood

The spontaneous combustion of coal lies at the bottom of the subject of storage. It is useless to store coal that is to be lost by fire from spontaneous combustion. Every engineer is familiar with the phenomena of the self-heating of coal, yet, for all that, spontaneous combustion is relatively rare. If we counted the times a portion of cod was stored where it would be undisturbed for a few weeks, the number of such storage operations in any one year would mount into the millions. Of these, a relatively small number show the phenomena of spontaneous combustion and time risk per ton is very small. It is extremely rare that in the smaller operations involving; only a few tons there is any heating. There is no spontaneous combustion of anthracite, and very rarely does the domestic consumer of bituminous coal find troublesome heating. The main interest in the subject lies in the large piles needed as reserves for public-service utilities, and the industries. Everyone desires to have directions for storage that are perfectly simple and yet will insure against loss. Unfortunately, the problem is too complicated for a simple solution. Many of the factors involved are difficult to determine, as we have no practical means of quantitative measurement. The factors involve chemistry, physics, and engineering, and the man who is

Jan 1, 1939

By S McKnight, L Koroznikova, J Begelhole

"This paper outlines a simple methodology for iron ore characterisation. Iron ores commonly contain a range of iron oxides with varying iron content along with generally minor quantities of lighter silicate gangue phases, giving rise to density variations. Companies tend to rely on heavy liquid separation (HLS) in the evaluation of samples arising from exploration, mining or metallurgical processes. Heavy suspension separation (HSS), a simple laboratory technique of density fractionation, employing suspensions of fine tungsten carbide (WC) particles in lithium heteropolytungstate (LST) solutions, can be used in the evaluation of iron ore.As part of Arrium Mining’s program to improve its knowledge of ore types being processed in two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed and geometallurgical evaluation for the OBPs has become a major focus.Metallurgical evaluation of the hematite ore ultra-fine size fraction, formally treated as waste but now upgraded by HSS, is a part of Arrium’s program to improve recovery.The HLS method for iron ore characterisation is not generally used as part of routine iron ore feed metallurgical evaluation due to the expense, toxicity and time-consuming nature of the technique. Results show that the HSS method for iron ore characterisation can achieve low-cost, low-toxic separation and can be used on-site to improve turnaround time of results (Begelhole, Jasper and Koroznikova, 2013).Arrium have applied this technique successfully for the past three years to progress process improvement for the two OBP as well as to assist Arrium’s on-site laboratory services, Bureau Veritas in Whyalla.The main objective of this program has been to further develop the HSS procedures using a low-toxicity, high specific gravity (SG) suspension; LST and WC as the dense medium for metallurgical evaluation of ultra-fines.A suspension of a particular density will separate iron ore into two products: a sink fraction (denser iron oxide – hydroxide particles) and float fraction (silicate – iron ore composite particles). A theoretical grade and mass recovery can be calculated, and a grade – mass recovery curve can be constructed for iron.Metallurgical evaluation of the plant feed ultra-fine size fractions are used to improve efficiency of an upgrading plant process. This type of characterisation can be used to prepare feed piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved.CITATION:Koroznikova, L, Begelhole, J and McKnight, S, 2016. Characterisation of Low-grade Hematite Ore Ultra-fine Size Fraction Particles by Heavy Suspension, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 327–334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D. Lauriski

The recent spate of catastrophic events at U.S. mines raises the question as to whether or not the mine safety and health system in the U.S. is broken. The prescriptive regulatory regime in the U.S. is not a cure-all for a broken system. Without totally dismissing the contribution of a prescriptive regulatory approach, this paper argues that safety in the U.S. mining industry would be enhanced if the nation adopted a scheme that provides a balance between specification standards and two alternatives: performance and systems-based standards. This would allow effective and flexible means to continuous health and safety performance improvement. Mine operators, regulators and politicians could then go beyond thinking that compliance alone equals strong safety by creating a proactive system that emphasizes continuous improvement. By adopting performance and systems-based standards, exemplary safety and health performers can be recognized, allowing regulators to focus their efforts on those without sound occupational safety systems and who have substandard safety performance. Mining Engineering, 2011, Vol. 63, No. 7, pp. 77-82. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By A. S. Ibrado, D. W. Fuerstenau

"Gold, silver and copper form various complexes with cyanide, of which only the singly charged dicyano form adsorbs appreciably on activated carbon. The adsorption of the dicyano complexes appears to be controlled predominantly by chemical reaction at the surface of a shrinking unreacted core. Metal uptake over time is non-linear, which eliminates control by boundary layer diffusion. The rate of adsorption is not enhanced by a reaction interruption, which suggests the absence of concentration gradients in the pores. Finally, the rate of adsorption increases with decreasing activated carbon size in a manner consistent with the shrinking core model. The results of this investigation accentuate the importance of efficient acid washing of carbon and removing carbon fines from the barren carbon stream. INTRODUCTION With the dwindling reserves of high-grade ores, most of the world’s gold is produced from low-grade ores by cyanide leaching. In the past, leaching was followed by the Merrill-Crowe process, in which gold is precipitated from clarified pregnant solutions by zinc cementation. This process is still being used for high-silver ores, where the cost of carbon stripping becomes prohibitive. For deposits with silver-to-gold ratios of about 4 or less, adsorption on activated carbon would be the usual solution purification step taken. The process simplifies solid-liquid separation and offers a viable solution to preg-robbing organic carbon in some ores. The modern industrial application of carbon adsorption started with the carbon-in-pulp (CIP) process, where carbon adsorption was used mainly as a solution purification step. In 1973, Homestake Mining Company commissioned the first large-scale CIP plant in the U.S.A.1 Later, carbon was added earlier in the circuit to control preg-robbing by adsorbing gold cyanide onto activated carbon as soon as it is dissolved. The scheme is successful because activated carbon is a stronger adsorber than the organic carbon found in preg-robbing ores. This process came to be known as the carbon-in-leach (CIL) process. Numerous research investigations have been performed on the chemistry involved in the CIP process, which at the time of its introduction was not clearly understood. Of these, research on the kinetics of adsorption probably bears the most immediate impact on industrial practice,2,3 where adsorption systems rarely reach equilibrium, if at all, and slight slowdowns in the adsorption rate can translate into significant decreases in revenue. To illustrate this, organic compounds, like flotation reagents, have been known to impair CIP circuits. However, laboratory tests showed that the organic compounds do not significantly affect the adsorption capacity of activated carbon. Rather, the harmful effect may be attributed to a lowered adsorption rate.4,5 Also well known is the faster rate at which fine activated carbon powders reach equilibrium compared to coarse activated carbon, even though the final (equilibrium) amount of material adsorbed per unit weight is the same."

Jan 1, 2015

By Victor F. Hollister, Robert W. Hodder

"The petrology and mineralogy of porphyry copper deposits are thoroughly described in recent literature and cited as the definitive characteristics for this type of deposit. The magmatic-hydrothermal aspect of genesis is also dealt with in detail. However, descriptions of their internal structure and regional setting are not as rigorous, and the genesis of this structure is simply stated as the release of high fluid pressures in a cooling magma emplaced along large fault zones. Genetic relationships between internal structure, regional setting and the tectonic evolution of continents has been alluded to infrequently in the past, but can now be considered together within the developing concept of orogeny at the margins of drifting crustal plates.Tensional structures, on both local and regional scale, and a Triassic to Tertiary age are described for porphyry copper deposits. We contend that such structure and age are distinct and unifying characteristics for this type of deposit and are genetically related to major crustal movements. British Columbia has porphyry copper deposits contemporaneous with plutons 180 to 200 million years old and 40 to 60 million years old. The former age group correlates with early stages of the continent's westward drift, and the latter group with a change in tectonic style during late development of the Canadian Cordillera. Hence, one can in British Columbia reflect on the genesis of a deposit's structure in the broader context of tectonic evolution. Such consideration should lead to more definitive criteria for area selection in exploration."

Jan 1, 1972