Search Documents

By L. D. van Dyk, G. S. Tshofu

Iron ore fines are by-products of iron ore mining operations. Unlike iron ore lumps, fines cannot directly be used in conventional iron making processes, and consequently large quantities accumulate around the world. Pelletizing and sintering can be used to convert iron ore fines into agglomerates or briquettes for processing with lump ore, but these techniques are energy intensive and produce greenhouse gases. This research investigated the extraction of iron from iron ore fines using acetylacetone (a ß-diketone) as an environmentally friendly alternative process for fines utilization. A 2k factorial experiment design was used to identify the significant extraction variables. It was found that the reaction temperature and solid to liquid ratio had significant effects on the extraction process. The extraction kinetics were studied at different temperatures and the highest iron extraction (97 %) was obtained after 48 hours at 413 K and 0.025:1 (g:mL) solid to liquid ratio for a particle size range of +106 to -150 µm. The extraction products were easily separated from the unreacted acetylacetone by flash distillation and iron(III) acetylacetonate crystals were recovered. An economic evaluation showed that selling the crystals was profitable. Alternatively, the crystals can be reduced with hydrogen to iron particles and acetylacetone (for reuse).

Jan 1, 2015

By Maria I. De Rosa

The U. S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (~300° C) and later (~400° C) combustion stages of chlorinated polyester-reinforced mine ventilation ducts could be predicted by a smoke particle characteristic, for the development of a test parameter. The experiments were conducted in an approximately 20-L furnace, at 14-min durations at set furnace temperatures of 2500 and 1,000° C, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were the hydrogen chloride (HCI), carbon monoxide (CO), carbon dioxide (C02), and oxygen (02) concentrations, furnace temperatures, the sample mass weight loss, the average smoke particle diameter (dg and average number and concentration (no), and the product of the average smoke particle diameter and concentration (dgno). Results show that the inverse of the smoke particle diameter-concentration product [(l/dgn0)], correlates directly and significantly with the primary gas toxicities evolved during both early (HCI) and later (CO) stages of combustion.

Jan 1, 1989

By Robert C. Sutter

In 1958, it became obvious to some of us in the solution mining business that there were certain problems in connection with our sodium chloride brining operations which were industry- wide. These were the types of problems which, while they were important to the safe and economical operation of our salt brining operations, were not such that their solutions would give an individual company a great competitive advantage over his competitor; and since they involve the safe and efficient mining of a natural resource, it was obvious that the answers would, in any event, be shared industry-wide. Since we were dealing with underground solution mining and, consequently, unseen and remotely controlled operations, the problems are formidable and the solutions difficult. While all of us were doing work to improve our operations, none of us could justify the expenditures necessary for basic research in these areas. Consequently, the idea was conceived of research sponsored by many companies with the same problems. In 1960, 11 companies entered into a' formal agreement to jointly support research on a specific problem of sodium chloride solution mining. The project to be undertaken was the development of a method for measuring the size and extent of underground solution cavities in sedimentary salt beds. It was agreed that all research was to be performed by independent research organizations. A part-time consultant or administrator was retained to administer the research contracts and to provide technical advice.

Jan 1, 1966

By Sebastiaan Peelman

NdFeB permanent magnets are the best available magnets used in many technology applications. However, at their end-of-life (EoL) most of magnets and the contained REEs are lost during the recycling of the bulk metals. The REEs are classified as the most critical raw materials in the European Union, and recycling of REEs from EoL products will reduce their criticality and contribute to the sustainability of REE. Various technological routes have been reported, but most of the methods are effective for highly concentrated magnets or magnet scrap, which is greatly dependent on expensive pre-dismantling processes. This paper presents various innovative metallurgical solutions to the effective REE recovery from current industrial practice for WEEE recycling, including the ferrous scrap from WEEE shredder products and shredder residues from computer hard disk drives. Both hydrometallurgical and combined hydro- and pyrometallurgical REE recovery routes are developed after demagnetization and physical upgrading.

By J. A. Marshall

"INTRODUCTION The purpose of this paper is to investigate the potential for use of UAVs in underground mines and present a prototype design for a novel autorotating UAV platform for underground 3D data collection. The mining industry has recently shown increased interest in the use of unmanned aerial vehicles (UAVs) to assist in everyday operations [20, 11, 4]. Above ground, small UAVs are in some cases a more efficient, inexpensive, and safer alternative to manned aircrafts currently used for photography, inspection and security [6, 10]. For example, attaching camera, infrared and LiDAR payloads, UAVs can provide a low-cost method of obtaining highly accurate 3D photogrammetric data and aerial photography. UAVs are now commonly used in open pit mining operations for applications that include stockpile surveying, 3D pit modelling, facilities management, accident reporting, progress monitoring, and environmental assessment [11]. There are numerous companies offering UAV services for mining applications; e.g., UAV Geomatics, Leica Geosystems, Sky Futures, SenseFly and FlyTerra, to name just a few. Common services include stockpile and open pit volume computations, environmental assessment, aerial mapping and photogrammetry. Although the aforementioned services are thosemost commonly provided by UAV surveying companies, they may also add value to other daily mining operations. For instance, SenseFly offers pre and post-blast monitoring in order to identify the presence of misfires and wall damage. This data can also be used to reconcile the blast results with expected results. GEM Systems offers a UAV equipped with a magnetometer for mineral exploration surveys. Companies such as Barrick have even used UAVs for solids modelling at tailings dams and stability monitoring [11]. UAVs in mining have so far been mostly limited to surface applications. Harsh underground environments pose many obstacles for flying UAVs. The confined space, dampness, reduced visibility, air movement, and lack of control signal propagation hinders most operators from being able to fly a drone underground. It may be that truly practical uses for UAVs underground will require either autonomous or semi-autonomous flight capabilities. Although there are many difficulties with flying underground, the potential benefits from a working system could greatly improve mining operations. The potential benefits of deploying UAV platforms underground include access to unreachable and dangerous locations and removing personnel from unsafe situations. These benefits have the potential to greatly improve mine monitoring and mine safety. Research has shown that current UAV technologies exist that allow for autonomous indoor flight. Extensive research has been done to develop UAV systems that are capable of performing on-board simultaneous localization and mapping (SLAM), which can allow them to navigate and map a foreign environment autonomously [5, 7, 1, 13]. Grzonka [7] successfully used an open hardware quadrotor to autonomously navigate and map an office building. The research outlines the localization, mapping, path planning, height estimation and control of the autonomous quadrotor. Other research has been done that exploits autonomous UAVs for search and rescue. Kassecker [9] proposed a software and hardware framework for a quadrotor capable of indoor and outdoor urban search and rescue and Rudol [19] developed a system for human body detection and geolocalization using an autonomous UAV.The use of autonomous UAVs in search and rescue has the potential to improve situational awareness and surveillance for a rescue team. Similar research has been done that uses autonomous UAVs for indoor exploration. Pravitra [15] outlined a strategy for autonomous exploration of miniature air vehicles (MAVs) within indoor environments and Rudol [19] developed a method for using an unmanned ground vehicle (UGV) and a UAV for cooperative indoor exploration. These studies show that aut"

Jan 1, 2017

By L. Ya Agapova

Emissions from pyrometallurgical processing of copper concentrates are usually subjected to wet scrubbing. The washing sulphuric acid so produced contains up to 0.2 g/L of rhenium, which is recovered by solvent extraction in the form of crude ammonia permeate (NH4ReO4). The mother liquor, obtained from the sulfuric acid wash, contains up to 35 g/L of rhenium and significant amounts of impurities. Crude rhenium salt is commonly processed by double recrystallization to produce marketable salt. A ton of high grade NH4ReO4 can be produced using 3.0-3.5 m3 of mother liquor. We propose an efficient technology of mother liquor pre-treatment aimed at removal of water-soluble organics with subsequent electrodialysis. Electrodialysis of mother liquor in a multichamber electrodialyzer resulted in the production of pure rhenium acid, from which a marketable NH4ReO4 is precipitated using ammonia solution. Multiple steps of recycling consisting of dissolution of NH4ReO4 salt, rhenium acid production from NH4ReO4 salt by electrodialysis and precipitation of NH4ReO4 from rhenium acid made it possible to upgrade the purity of obtained rhenium compounds by 1-2 orders of magnitude. A rhenium metal powder of 99.997% purity was produced by high-temperature reduction of high-purity NH4ReO4 with gaseous hydrogen. Rhenium metal powder of high purity can be produced from sulfate solutions of NH4ReO4 by non-platinum anode-based membrane electrolysis processes also. Keywords: rhenium, mother liquors, membranes, electrodialysis, rhenium acid, ammonia perrhenate, reduction, powder, electrolysis

Sep 1, 2012

By M. Yavuz

As a branch of Operations Research, decision making is a widely used application in both science and social sciences. There are many different methods developed to solve decision making problems in the literature. In this study, Fuzzy Analytic Hierarchy Process (AHP) method is performed for the selection of reclamation project selection in an open pit mine and the optimal solution of the problem is investigated. Different reclamation project alternatives are prepared for an open pit mine, which continues to its production activities in magnesite sector in Turkey. The data obtained from Magnesite Cooperation is used in the application of the method. A decision-making process is prepared as considering the project alternatives for the purpose of selecting the most suitable reclamation project. The entire criteria that affect the decision-making process are identified and transformed into a hierarchical structure. The problem is solved by using Fuzzy AHP method developed according to this structure. It is found that Fuzzy AHP is a method that may help decision-makers in solving different decision-making problems in mining.

Aug 1, 2013

By D Johansson, A Nordqvist, D Mihaylov, N Petropoulos, M Wimmer

The flowability of the caved rock masses in the sublevel caving (SLC) mining method is of great importance. During the blasting process of a SLC-ring, the caved rock mass in front of the ring is compacted. As a result of this compaction, the mechanical properties of the fractured rock masses change, for example void ratio, angle of internal friction and structure of the compacted material. The changed mechanical properties of caved rock mass and recent blasted material can influence the mobility of the material, which could result in blockage of the flow path of the material. The identification of the involved mechanisms in this process can be done after a series of tests in different scales. However, there is no available equipment for dynamic measurements during blasting, ie velocity and displacement of the burden and in the caved masses. This study focuses on the development and laboratory evaluation of a measuring system that can be installed in a borehole. The first trial was carried out in a pillar, where two blastholes had been drilled (9.5 m) parallel with the drift and two measuring holes (16.5 m) were perpendicular to the drift. Two measuring systems were installed in the measuring holes. Some preliminary tests were carried out to find suitable initiation procedures for the emulsion explosive. Applicability and robustness of the developed measuring system were also evaluated. In addition to these tests, an expandable cement mixture was developed to firmly anchor the measuring systems in the boreholes. The measuring system consists of an anchor, armoured cable in a pulling tube and a protective case. The anchor is equipped with uniaxial and triaxial accelerometers. A potentiometric measuring system for displacement up to 2 m is installed at the end of the pulling tube and connected to an extendable spiral cable. All sensors are connected to a data acquisition system (DAS). Both measuring systems have their own DAS to acquire data in case of failure of one of the systems. The measuring system was tested in laboratory conditions with impact velocity up to 10 m/s. It was proven to be functional and gave reliable results.CITATION:Petropoulos, N, Mihaylov, D, Johansson, D, Wimmer, M and Nordqvist, A, 2015. Design of equipment for dynamic burden measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 493–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By W. A. Jones

THE Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is situated near the north end of lot 1, concession 2, Hislop township, Ontario. The property comprises the north half of lot 1, concession 2, and the south one-third of lot 1, concession 3. It is readily reached by a good motor road from the village of Ramore, 7.5 miles to the southeast on the Temiskaming and Northern Ontario railway. The-mine has been developed to a depth of 900 feet and the current daily production rate is about 260 tons. From the inception of operations in March, 1935, until December 31st, 1942, 455,720 tons of ore with a total value of $4,169,-316 have been milled. The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines. The deposit is interesting because the relationship between hydrothermal metamorphism and three successive stages of fracturing and mineralization is marked with considerable clarity. During the past seven years, detailed geological maps of the mine have been kept up to date, many thousands of feet of diamond-drill core have been logged, and numerous thin and polished ore sections have been studied. The present paper describes the structure and mineralogy of the orebodies.

Jan 1, 1944

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid Deep Mixing (DM) shoring system was recently constructed for a high-rise development in downtown Vancouver, British Columbia, Canada for the temporary support of a five-level basement excavation. The site is bounded by an existing bridge off-ramp structure along its longest side and by city streets on the other two sides, which formed a truncated triangle in plan. A conventional secant pile wall was installed along the longest side, about 380 ft (116 m) in length, of the site. Hybrid shoring walls (HSW) 1 and 2 were installed along two shorter sides with each being 235 to 246 ft (72 to 75 m) long. HSW 3 completed the excavation support system along the shortest side with a length of about 55 ft (17 m). Cutter soil mixing (CSM) was proposed by the excavation and shoring design-build team in lieu of conventional secant piling. CSM was the preferred method to construct the infill panels between soldier piles because of the speed at which the shoring system could be constructed in the variable fill, peat, wood waste and overburden. Design ConsiderationsTo minimize the impact on buried utilities along the outside perimeter of the excavation, the temporary shoring was designed to limit the lateral displacements to less than 0.8 in (20 mm). Factors taken into consideration for shoring design included the lateral earth pressures from the fill and native soils, groundwater pressures, temporary construction loads (e.g., crane or heavy plant/equipment), and permanent structural requirements. The subsurface conditions at this site typically consisted of fill (cohesive and granular), overlying peat and/or wood waste, overlying clayey silt to sandy silt, overlying weathered to dense to very dense clayey silt till to sandy silt till with silt layers. Localized, perched groundwater was observed within the fill, peat, wood waste and sandy silt layers above the dense till."

Jan 1, 2017

By J. van Deventer

Volatile gold prices in the face of rising costs for mining and refining is causing the mines to look for new ways to reduce costs and increase recoveries. This task is complicated by the fact that the gold in hereto unexploited reserves is associated with increasingly complex ores - either preg-robbing, refractory, associated with high concentrations of copper, or all of the above. Ion exchange resins can play a significant role in this quest for improvement. Although ion exchange resins have been used in Former Soviet Union (FSU) countries for the recovery of gold for many decades, it is still not widely used in the Western World. Synthetically manufactured ion exchange resins can be tailor-made to suit the chemical and mechanical characteristics of a specific application. As such, ion exchange resins can be used in a variety of solution matrices (e.g. cyanide, thiosulphate and acid), and process designs (recovery from clear liquor after solid-liquid separation or directly from the leached pulp). In this paper, a number of applications are discussed along with a review of recent developments in ion exchange technology.

Jan 1, 2014

By Charles R. Harrison

The purpose of this study and resulting development of the training program, "Safety--Let's Make It Happen" was to determine the relation of concepts to the development of desired Health and Safety behavior. After extensive pre-contract study, it was hypothesized that improved acceptance and understanding of the Federal Coal Mine Health and Safety Act of 1969 could possibly contribute to the reduction of accidents. Second, in order for an individual to accept and understand the Act, he or she must have a working knowledge of its purposes and application. Third, acceptance and understanding of the Act, necessary to protect the individual from negligence, was imperative. Fourth, an actual operating company could provide the base in which to test these hypotheses in a meaningful manner and develop this type of training program. Six assumptions were agreed upon before embarking on this study and training program development. (1) In the cognitive process, a concept introduction into an individual's personality may result in a behavior quite different than if he or she had been exposed to a different concept.

Jan 1, 1977

By Kari Niiranen

LKAB (Luossavaara-Kiirunavaara AB) is operating iron ore mines, concentration plants and pelletizing plants in Northern Sweden. The largest of the apatite magnetite deposits and the mines are Kiirunavaara with annual production rate of approximately 27 Mt crude ore underground. LKAB produces two varieties of pellets: blast furnace pellets and direct reduction pellets (LKAB DR Oxide Pellets). Meanwhile the concentration process in a sequence of the low intensity magnetic separation (LIMS) and flotation at the concentration plant. In spring 2007 there were noticed great fluctuations of SiO2 grade in the crude ore. The high SiO2 grade is particularly problematic in the case of direct reduction pellets. In consequence, a project was started (called Silica in the Mine) to define exactly the problem related with silica and to find out, if possible, the reason for the great fluctuation of SiO2 grade in the crude ore going to the processing plant. A further target of this project was to develop a simplified method at the laboratory scale, to predict SiO2 grade in the magnetite concentrate in the future, but also predict the physical properties of the ore with respect to mineral processing. The essential stage of systematic characterization of the ore body for mineral processing properties is the estimation and simulation of different parameters from the laboratory scale to the large scale at the concentration plants using empirical data collected at the mineral processing by LKAB in Kiruna. Further a target was also to find useful physical parameters for mineral processing and implant those parameters into the existing geological 3D-model of the deposit. This information will be used for making prognosis of the future mining and the quality of the crude ore. It will also give better control and improve the production planning in the mine and the performance at the concentration plant in Kiruna concerning the decrease of the SiO2 grade of the magnetite concentrate.

Sep 1, 2012

By Gaballah Djona M.

Spent hydrorefining catalysts contain about 5 % of CoO and/or NiO, 12 % of MoO3 and up to 10 % of V205. They are generally supported by alumina and contain up to 25 percent of C, S and hydrocarbons. Such materials are potentially hazardous to the soil and to water resources. Selective chlorination of raw unroasted samples with Cl2 + air gas mixture had been investigated. At temperatures lower than 600 °C, it was possible to recover more than 90 % of nickel and cobalt chlorides, about 99 % of the molybdenum and up to 75 % of vanadium chlorinated compounds. CoCl2 and Ni/Cl2 were extracted from the chlorination residues by their dissolution with acidified water. Molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The chlorination of Al2O3 could be limited to less than 6 %. The scale up of this treatment was successful and a flow-sheet is proposed.

Jan 1, 1995

By A. Noël, R. Lapierre, M. Provencher

"Modem aluminum smelters are facing significant operating cost pressure. Key methods used by smelters to manage this pressure are automation and production-information systems to optimize processes, manage quality, anticipate problems and reduce operating costs. In 2002, Aluminerie Alouette Inc. began its Phase II Expansion project, and retained the joint venture of SNC-Lavalin and Hatch (SLH) as its engineering, procurement and construction management (EPCM) team. Alouette had the distinction of being one of the most efficient aluminum smelters in the world. Alouette already understood the importance of systems integration in project delivery. For Phase II, key objectives were identified to ensure ""a state of the art"" integrated architecture that would support Alouette's production goals to integrate the existing facilities with the expansion, to form a single efficient facility and meet project schedule and budget targets. Achieving those objectives within the context of a large project often creates major challenges due to the nature of the traditional EPCM delivery model, which relies on several vendors and third-party-systems integrators. In this case, an integrated Alouette-SLH team was made responsible for all aspects of the systems integration, taking over the task from most suppliers. The integrated team was responsible for delivering an automation system and plant-wide-production IT system for the new facilities while accommodating migration for the existing systems. Through the use of rigorous methodology and advanced state of the art technology, the IT and automation strategy led to significant value creation and is recognized today as one of the key factors of the project's success. The primary results were: fast and efficient start-up of facilities, due to quality programming and implementation; a plant able to operate as a single entity; automation and IT systems delivered before time and under budget; standard programming methods implemented throughout the plant; and reduced and simplified maintenance."

Jan 1, 2006

By J. B. Hiskey

Of the halogens, the gold iodide complexes are the most stable in aqueous solutions. A series of experiments were performed to investigate the kinetics and mechanism of the leaching reaction between gold and iodide. Using a rotation disk technique, the effects of rotation speed, iodide and iodine concentration, temperature, pH and in the presence of different electrolytes were measured. Oxygen and hydrogen peroxide were also examined as oxidants in the iodide system. The first order reaction rate was found with respect to 13 and half order reaction rate with respect to 1-. The comparison of gold leaching between iodide and cyanide is also presented, in which a rate constant of about 2.6x10-9 mol/cm2? sec for 10-2 M I- and 5x10-3 M I2 was obtained. This value is close to that -for typical cyanidation. Cyclic voltammetry experiments were also performed to examine the electrochemical nature of the reaction which will be presented in part II of this study.

Jan 1, 1990

By I. D. Ustinov, V. A. Arsentyev, A. O. Mezenin, A. M. Gerasimov

"The solid mineral raw materials of the sediment deposits containing the argillaceous variations such as the coal and the potash ores are the most multi-tonnage solid minerals mined and processed in the territory of the Russian Federation. Both types of the deposits have relatively simple geology aspects with large and medium-sized solids and as a rule, the most often, with the regular bedding which are characterized by the fitchery thickness and the internal structure. Such deposits are very difficult for mining and processing. The thermal modification of this of ores allows changing the physico-chemical properties of its components in such a way that their further processing - grinding, separation, transportation and storage can be carried out without the use of process water or significantly reduces its consumption. The purpose of the present study is to increase the efficiency of the mineral processing containing the layered aluminum silicate by reducing their negative impact on the basic dressing processes, the separation of suspended matters and the storage of waste. INTRODUCTION Many deposits of minerals are associated with the presence of layered silicates such as the argil, mudstones, argillaceous slate - highly hydrophilic mineral varieties which have the ability to swell in the water. This ability to self-disperse creates the great difficulties both for the extraction and the processing of such ores. Since the dressing of most minerals is associated with the use of wet processes, where in contact with water the swelling layered silicates are dispersed to a particle size of less than 50 µm, but due to their high hydrophylic property they form bonds that promote the formation of so-called structured suspensions having increased viscosity. In this case the structured suspensions make it difficult to perform the separation operations as the classification, the gravity and magnetic separation, the flotation and thickening and filtration operations."

Jan 1, 2018

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTIONThe process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic.A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities."

Jan 1, 2012

By M. W. Pullen

It is recognized that the determination of electrical resistivity of the earth within a given area may furnish information concerning the location of certain mineralized strata of economic importance. Present knowledge of the electrical resistivity of the various rock formations is almost nil, and the geophysicist who is detailed to make a survey of an area without any data as to the relative resistivity of the underlying rocks is greatly handicapped. Such surveys are usually made within areas known to contain mineral deposits to aid in locating desirable points for drilling. Usually these areas have been prospected by diamond drilling, and drill cores of the various rocks and ores are usually obtainable. Were it possible to make resistivity tests in a laboratory of the drill cores or from pieces of the rocks and ore within an area before attempting a field survey, this would indicate not only the advisability for such a survey but would aid considerably in the interpretation of the results of such a survey. To be of most value a definite method should be used for all such tests, and as yet such a method has not been established.

Jan 1, 1929

By J. Morris, R. Sellaro

El petrodiesel es un colector común para la flotación de carbón, pero la partición de compuestos orgánicos de diesel (DRO por sus siglas en inglés) en corrientes de proceso no ha sido ampliamente estudiada. Investigaciones preliminares sugieren que bajo esquemas de dosificación normales los contenidos residuales totales de DRO en aguas de procesos deben estar limitados a la fracción soluble en agua (WSF por sus siglas en inglés) sub-ppm. Es más, los hidrocarburos aromáticos poli-cíclicos (PAH por sus siglas en inglés) debería segmentarse de manera proporcional con los compuestos orgánicos de diesel (DRO). El propósito de este estudio fue confirmar estos resultados en pruebas de flotación realizadas en laboratorio. Se midieron los contenidos totales de DRO Y PAH en aguas asociadas con los flujos o corrientes de concentrados y relaves. Los resultados muestran que las aguas con concentrados tenían de manera consistente mayores cantidades de DRO que las aguas de relaves. Es más, los contenidos de DRO en ambos flujos generalmente se incrementaban con el aumento de la dosis de diesel. De acuerdo con la investigación preliminar, los DRO parecían estar limitados a la fracción soluble en agua (WSF) y los PAH tendían a segmentarse proporcionalmente con los DRO. Bajo condiciones de operación típicas, los DRO residuales no deberían representar una preocupación medioambiental, pero deben evitarse situaciones que permitan una sobredosis significativa de diesel.

Jan 1, 2014