Search Documents

By J. W. Latilla, J. J. van Wijk

In late 1997 a request was received to assist with determining the powered support unit (shield) load capacities for the planned 2 seam short wall. This project had a number of aspects which made it attractive to utilize numerical modelling in conjunction with other more conventional design tools in the design of the shields. Amongst these were: The 2 seam panels were to be laid out about 25 m below the previously short walled 4 seam, the 4 seam had in turn been over-mined by the 5 seam long wall, the proposed face height of the 2 seam short wall was 5.5 m while the 4 seam had been mined at 4 m. The top seam in the area (5 seam) had been mined at between 1.5 and 2.2 m high, the face conditions with about 95 m of broken material applying dead weight loading to the 2 to 4 seam inter-burden septum were hard to predict and cyclical loading due to the presence of strong sandstone bands in the 2 to 4 seam inter-burden. The basic thrust of the study was to take the known, and successful, situation (4 seam short wall) and carry out comparative modelling to enable prediction of likely 2 seam conditions. Some two dimensional aspects studied were: 5 m goaf hanging up behind shields, stresses in beams to determine likely first goaf roof span, stresses in cantilever beams to asses cyclical loading due to sandstone bands in the interburden being loaded by the overlying goaf and stresses on chain and crush pillars adjacent to the goaf edge. Three dimensional aspects that were investigated included: Load distribution along face for close goafing and 5 m goaf hang-up and load in a 1 m wide rib modelled in the position of the powered support units. From the modelling it was possible to determine the optimal shield leg capacity of the new 2 seam equipment. These outputs were used when drawing up the technical specifications for manufacture of the new equipment. The face was successfully commissioned in August 2002. Fin 1997, requête fut faite pour aider à la détermination des capacités de charge pour l’unité de soutènement mécanisée (bouclier) pour la couche 2 courte taille en projet. Certains aspects de ce projet le rendaient intéressant pour utiliser la modélisation numérique en même temps que d’autres méthodes conventionnelles pour la conception des boucliers. Parmi ces aspects se trouvaient : Les panneaux de la couche 2 devaient être placés environ 25 m au dessous de la couche 4 courte taille ; la couche 4 avait été remplacée par la couche 5 longue taille ; la hauteur de taille proposée pour la couche 2 courte taille était 5.5 m, tandis que la couche 4 avait été exploitée à 4 m. La couche supérieure de la région (couche 5) avait été exploitée entre 1.5 et 2.2 m de hauteur ; il était difficile de prédire les conditions de taille, avec environ 95m de matériaux cassés ajoutant une charge morte à la plaque de séparation entre les couches 2 et 4 et un chargement cyclique causé par des bandes de grès dans l’entre-fardeau 2-4. L’idée principale de l’étude fut de prendre la situation connue et réussie (couche 4 courte taille) et de faire une modélisation comparative pour prédire les conditions probables de la couche 2. Certains des aspects à double dimension qui furent étudiés étaient : Un accrochage de remblai de 5m derrière les boucliers ; contraintes dans les poutres pour déterminer le premier intervalle probable entre remblai et toit ; contraintes dans les poutres en porte-à-faux pour évaluer le chargement cyclique causé par les bandes de grès dans l’entre-fardeau qui est accablé par le remblai et les contraintes sur les piliers par chaîne et d’écrasement adjacents au bord du remblai. Aspects à trois dimensions qui furent étudiés : Distribution de la charge le long de la taille pour les remblais proches et l’accrochage de remblai de 5 m et la charge dans une nervure de 1 m de large modelée dans la position des unités de soutènement mécanisées. La modélisation a permis de déterminer la capacité de portée optimale du bouclier du dispositif nouveau pour la couche 2. Ces résultats furent utilisés pour dresser les spécifications techniques pour la fabrication de l’équipement nouveau. La taille fut commissionnée avec succès en août

Jan 1, 2003

By Craig S. Hartley

Expressions are obtained for the energy changes associated with the reaction of (a& (111) slip dislocations on intersecting (110)planes in anisotropic bcc metals. An energy criterion for assessing the likelihood of dissociation of the products of such reactions is also presented. It is found that the "burrier reactions" which form a(100) dislocations at the intersection of two active {110) slip planes are more energetically favorable in metals which exhibit a high value of Zener's anisotropy factor, A, than those which have a low value. The results are presented in a form which permits the stacking fault energy to be obtained from a measurement of the separation between par-tials in a dissociated configuration. However, until accurate calculations or measurements of the stacking fault energies involved are available, it is not possible to assess the physical importance of dissociated dislocations. In a recent paper,' the energy changes associated with several types of reactions between two slip dislocations, (a/2)(111){110), in bcc structures were calculated.* Isotropic elasticity and the approxima- tion v = -3- were employed. The purpose of this work is to present calculations of the energy changes for many of the same reactions using anisotropic elasticity. The problem of dissociation of a(100) and a(110) dislocations is also considered, and maximum fault energies for which dissociation will be energetically favorable are calculated for several bcc metals. Two general types of reactions are considered; those for which the reactant (a/2)(111) dislocations have long-range attractive forces and those for which the reverse is true. An example of the former is: (a/2)[lll] + (a/2)[lll]-a[l00] while the latter are typified by: (a/2)[lll] + (a/2)[111] -a[011] Only reactants lying in different slip planes are considered; therefore, the products must lie along (111) or (100) directions, which are the intersection of two {llO} planes. It will be assumed that the reactants and products are infinitely long parallel dislocations, since in this case the energy change associated with the reactions is a maximum.' THEORY The self-energy per unit length of a straight mixed dislocation in an anisotropic medium can be written? where b is the Burgers vector, K is an appropriate combination of the single-crystal elastic constants, and R and ro are, respectively, outer and inner cut-off radii of the elastic solution. The energy given by Eq. [I] does not account for any variation of the core energy with orientation. This could be manifested by an orientation dependence of the core radius or, equivalently, the Peierls width, of the dislocation. However, the energy contribution due to this source is expected to be small, and current models of the dislocation core are not sufficiently accurate to justify such a refinement. It has already been shown that for the isotropic case the energy contributions due to nonzero tractions across the cores of the reactants and products exactly cancel one another in the reaction.' Accordingly, it will be assumed that this contribution to the total energy change in the anisotropic case is small. In the subsequent discussion it is also assumed that the core radii of the reactant and product dislocation are the same and that, where stacking faults are formed, the faulted region is bounded by the centers of the partials. Consequently only changes in elastic energy due to the reactions will be considered. When the dislocation is parallel to either the (111) or the (100) directions, K may be written:375 K = (Ke sin2 a + Ks cos2 a) [2] where K, and Ks are the combination of elastic constants corresponding to an edge and screw dislocation lying along the same direction as the mixed dislocation, and a is the angle between the direction tangent to the dislocation line and the Burgers vector. Eq. [2] should not be confused with the isotropic approximation to the variation in energy with line Orientation.6 It should be noted that the essentially isotropic expression for K is a result of the characteristic symmetry of the (111) and (100) directions and is not, in general, valid for other dislocation directions in anisotropic cubic metals. The energy* change for a reaction in which the re- actant and product dislocations are parallel perfect dislocations can be written: where Ep and E, refer to the self-energies of the products and reactants, respectively. For dislocations parallel to (100) and (111) directions, Eq. [3] becomes:

Jan 1, 1969

By Werner Schwartz, Wolfgang Haase

Lead sulfide concentrates, which may include other lead concentrates, are sintered on an up-draught sintering machine without the addition of any diluting agents or fluxes. Subsequently they are melted in an oil- or gas-fired rotary furnace. The sintering and melting processes are based upon the following roast-reaction: PbS + 2 PbO = 3 Pb + SO, PbS + PbSO, =2 Pb + 2 SO, For obtaining a lead bullion free from sulfur, the sintering process is carried out in such a way that the sinter product contains a small amount of excess oxygen above that to react with the sulfides. At the end of the melting process, when the reactions are finished, the remaining small amount of oxide residues is reduced with coal to which a certain percentage of soda ash (about 1 pct of the lead bullion) is added. For the lead smelting process described neither coke nor fluxes—except soda ash—are required. This process is being utilized by a European smelter successfully and with a high lead recovery. The consumption figures for the smelting of 100 tons per day of lead concentrates are indicated. The lead content of the lead concentrates from modern ore dressing plants ranges from 65 pct to above 80 pct. In most lead smelters of the world these concentrates are smelted in a blast furnace. For blast-furnace smelting the concentrates have to be desulfurized and agglomerated by sintering. A requirement for the perfect operation of a down-draught sintering machine and of a blast furnace is a maximum lead content in the feed of 40 to 45 pct. For this reason, some lead concentrates have to be diluted by adding return slags, limestone, and possibly iron oxide and sand. As an example, 100 tons of lead concentrate with 72 pct Pb would contain 13.5 tons of gangue (including the zinc). To produce a perfect sinter with 42 pct Pb it would be necessary to add 70 tons of flux and return slag, more than five times the original weight of the gangue, to the sinter mix and blast-furnace charge. A correspondingly large amount of coke would be required in order that all of these materials reach the heat of formation and the melting temperatures of the slag (1200" to 1400°C) inside the blast furnace. The roast-reaction process presents a possibility for lead recovery without dilution of the concentrates. In this process the concentrate mixed with coal is placed upon a Newnam-hearth and air is blown through nozzles into the heated mix. AS a result metalllic lead and a relatively great amount of so-called .'Grey Slag" with a lead content of 25 to 35 pct are formed. The slag is sintered to eliminate sulfur and, after addition of the requisite fluxes, treatt:d in a blast furnace. Owing to the poor recovery of lead from the hearths and to the unavoidable heavy hand-work plus the risk of poisoning this process is utilized in very few 112ad smelters today. Since in mxny countries of the world coke is expensive and difficult to obtain, it appeared feasible to use the principle of the roast-reaction by modern sintering and melting methods with recovery of the lead in electric, or oil, gas, or coal-fired furnaces. Two processes are utilized on an industrial scale: A) Lead smelting in the electric furnace of the Bolidens Gruv A/B in Sweden, as described by S. J. Walldcn, N. E. Lindvall, K.G. Gorling, and S. Lundquist. B) The self-fluxing lead smelting of Lurgi Gesell-schaft fiir Chemie und Huttenwesen m.b. H., Frankfurt a M, Germany, which is described in this paper. In the Boliden process referred to above the sinter mix is pelletized by enveloping return fines with layers of flue dust, limestone powder, and dried galena concentrate. The roasting and agglomeration are carried out on a down-draught machine, and a slight excess of sulfur is left in the sinter product. During the smelting in the electric furnance the roast-reactions occur and a slag poor in lead and a sulfur bearing lead are formed. This latter is subsequently oxidized in a converter to obtain lead bullion and dross. The Lurgi-process achieves the maximum possible extent of the roasting reaction on the sintering machine. The wet flotation concentrates are blended with return fines (lead content 70 to 80 pet), any existing flue dusts and lead slimes—but without the

Jan 1, 1962

By Luc Delaey, Horace Pops

The structure and morphology of thermoelastic and burst type martensitic phases that form upon cooling in Cu-Zn-Si p phase alloys have been studied by transmission electron microscopy. The martensitic phases are composed of a lamellar mixture of two close-packed structures with different stacking sequence, namely ABCBCACAB (orthorhombic) and ABC (fcc). Striations within thermoelastic martensite are most likely produced during interaction with impinging burst-type martensite and not as a consequence of secondary shears. In a study of the martensitic transformation in ternary Cu-Zn based 0 phase alloys1 the dependence of the martensitic transformation temperature, M,, with composition shows variations for elements within a constant valence subgroup and between different subgroups. Such variations are not reflected in a change in habit plane, which is approximately the same for each ternary alloy, namely in the vicinity of (2, 11, 12 Ip. The fact that the habit plane remained constant, despite large differences in M, temperature and electron concentration, suggested2 that the crystal structures of the martensitic phases could be nearly the same. Crystal structures of ternary Cu-Zn based martensites have been determined recently for alloys containing the three-valent elements gallium3, 4 and aluminm. The present studies have been made to examine the structures and morphology of the martensitic phase in ternary Cu-Zn based alloys containing a four-valent element, silicon. I) PROCEDURE Two alloys were prepared by melting and casting weighed quantities of the component high-purity metals in sealed quartz tubes under half an atmosphere of argon. They were subsequently remelted by levitation under a protective atmosphere of argon. After allowing for losses of zinc as determined by the difference in weight before and after casting, the compositions in atomic percent of both alloys were established to be Cu-33.5 Zn-1.8 Si and Cu-27 Zn-5.0 Si. These alloys were homogenized in the P-phase field for 2 days at 800" C. Bulk samples consisted of a martensite phase at room temperature, the M, temperature being approximately 30' and 200" for the 1.8 and the 5 pct Si alloys, respectively. Thin disks were cut from the ingots using a spark machine, and they were heated for 5 min at 800' and quenched into water in order to obtain martensite. These slices were thinned chemically at room temperature in a solution consisting of 40 parts HN03, 50 part H3PO4, and 10 parts HC1 and thinned further electrolytically by the Window technique, using a voltage of 15 to 25 v and a mixture of 1 part HN03 and 2 parts methanol, which was kept at a temperature near -30° c. Foils were examined by transmission electron microscopy using a Philips EM 200 electron microscope. 11) RESULTS AND DISCUSSION 1) Structure and Morphology. Fig. 1 shows the martensitic phase in the alloy containing 1.8 at. pct Si. This phase is composed of contiguous platelets, each containing striations. The direction of the striations changes at the boundary between individual platelets. These internal markings resemble the striations that are usually identified as stacking faults, as for example in Cu-A1 martensites6-a or the lamellar mixture of two close-packed phases in Cu-Zn-Ga marten-sites.3p '9 lo In the present alloys, selected-area diffraction experiments have been obtained in order to determine the nature of the striations. Figs. 2(a), (61, and (c) are electron diffraction patterns of an area inside a single martensite plate. Fig. 2(a) contains diffraction spots which correspond to two close-packed structures with different stacking sequences, namely ABCBCACAB (orthorhombic) and ABC (fcc). Spots belonging only to the fcc structure are indicated by arrows. By tilting the foil either the orthorhombic structure, Fig. 2(b), or the cubic structure shown in Fig. 2(c) may be obtained. When the foil is oriented so that only the diffraction spots of the orthorhornbic structure are present, bright-field illumination shows small lamellae, as seen in Fig. 3. In this figure the lamellae that belong to the fcc structure are bright bands inside the dark extinction contours of the orthorhombic structure. The boundaries of the lamellae are parallel to the basal planes of the orthorhombic structure and to the {Ill} planes of the cubic structure, the close-packed directions of both structures being parallel. The 5 pct Si alloy shows similar features as those described for the 1.8 at. pct Si alloy.

Jan 1, 1969

CHAIRMAN LITTLEJOHN: Some of the members will want to question Mr. Farnham on some of the things he has brought tip, so we will throw the meeting open for discussion. I am quite sure Mr. Farnham will be willing and glad to answer any questions that may be put to him. MR. HOLMAN: I would like to ask Mr. Farnham a question in regard to the Duckbill: How wide a face will it operate without moving the bill? MR. FARNHAM: The Duckbill is a device that was developed in the Union Pacific Mine at Rock Springs, within the last few months, and it is shaped something like, a dustpan, with discharge throat in the rear. They made one seven feet wide and found it was too wide, and the one they are using now is between three and four feet in width. The front section of the conveyor, which attaches to the duckbill, meshes into it to form a sliding section, and the front end of the Duckbill is pushed by the upper segments. I saw one used in a room twenty-four feet wide, and they drew it back after they cleaned out one room and pushed it forward again. MR. HOLMAN: You have no arrangement other than ratchet work? MR. FARNHAM: The ratchet is for forward working and back; the sections are made 12 or 13 feet long, and the stroke of the conveyor automatically works the ratchet; they can ratchet it back; it is a hand device. MR. HOLMAN: They just swing the end of the conveyor across the face to pick up the loose coal? MR. FARNHAM: Yes; they are also planning to use it endwise along the panel face, that and the room work both are quite new in their application, and I do not think the Union Pacific is giving out any results as yet, because the system has not been in use long. MR. HOLMAN: We are planning on putting one in very shortly. MR. HALL: I understand they can swing it over 30 degrees one way or the other, and it goes the same way easily because of the continual jar of the back and forward motion on a 60-degree swing. SECRETARY SHUBART: Take on a comparatively long conveyor, you can get quite a sweep, a large part of the circle. The Duckbill could command quite a large range. For a 12-foot entry, take a four-foot wide advance through the middle of the shot coal, with a 12-foot advance, ratchet back, swing the Duckbill to the rib and repeat; but I do not think they could get as much as 60 degree. on the end of the Duckbill without curving further back. The conveyor is light and not normally set on any permanent foundation. I saw one of Mr. McCarty's first machines, a rather rudimentary one, clean tip a 12-trot entry, 21 tons of coal, in 16 minutes, three men at the face and one at the loading end. MR. FARNHAM: The average time to clean the entries is about an hour-to clean up good-it wouldn't take but a short time; that is why they get this record of several cuts a shift. CHAIRMAN LITTLEJOHN: Are there any other questions you would like to ask Mr. Farnham? MR. HOLMAN: We were discussing this entry driving in regard to the entry loader; an entry loader in advance work, just what you have to do to place the jackbars with the sheave-blocks? Do you dig along the ribs after the coal is shot or do you have any other scheme that could be worked out to a good advantage? MR. FARNHAM: This record is a report I have just received from our Chicago office, without the full details, which I have written for. I am sorry I cannot give you the details. This was an Indiana or Pennsylvania mine, near Pocahontas, not the one where they had an accident. I assume they set the jacks ahead and swung and dumped the coal partly out with a scoop and partly by hand, but the application for that for entry driving is entirely new. The reports stated that they anticipated using that as a standard method of entry driving in the future. I will be glad to see that you get a copy of it when I get the report completed. MR. MONAY: Mr. Shubart, did you say they loaded 12 tons in 16 minutes? SECRETARY SHUBART: Twenty-one tons. MR. MONAY: How long did it take to change the machinery out of there

Jan 1, 1926

By E. B. Fitch, E. C. Johnson

The operating behavior of liquid-solid cyclones is outlined, together with the nature and range of the process results obtainable, to serve as a background for engineers wishing to consider application of this new process tool. BY now most engineers are familiar with the liquid-solid or Dutch State Mines cyclone. However, it should be helpful to know exactly what it is that the equipment does and what its limits are. Without going into cyclone theory, this paper will describe the operating characteristics of Dutch State Mines cyclones. These are manufactured under license in this country and sold under the trade-marked name of DorrClone. The physical construction of the liquid-solid cyclone has been covered in many papers,'-' the DorrClone in particular being described in some detail by Weems. Fig. 1 shows the unit in cross-section. The feed enters at C. The coarse, heavy particles are thrown centrifugally to the periphery and make their way down the wall to the apex where their rate of discharge as underflow is controlled by an adjustable rubber apex valve. As the apex diameter is decreased the solids build up behind the valve, producing a denser underflow. Meanwhile the fine particles are swept into the upward flowing vortex stream which exits as overflow through the vortex finder, F. Flexibility to produce the specific result desired in a particular process is achieved by providing means for varying the areas of the entrance, vortex discharge, and apex discharge. The entrance area may be varied by insertion of special shims. Vortex discharge area may be changed by use of different-sized vortex finders which are interchangeable. Similarly, the different sizes of apex valves are interchangeable and in addition each apex valve is variable down to about 60 pct of its maximum diameter. A most significant primary distinction to make is that although liquid-solid cyclones have been sometimes called thickeners, they actually are classifiers, and very potent ones. They are almost never thickeners in the special sense that many metallurgical engineers understand the term. There would be no profit in quibbling over the definition of a word, but when the application of cyclones is considered, it will help to understand the difference be- tween two mechanisms, one of which will be called classification, and the other thickening. In what is called thickening the fine solid particles present in the feed hold together by surface attraction during the sedimentation process. The loose network of particles thus held together constrains all particles to settle at approximately the same rate, the larger ones dragging the smaller ones down. As a result, pulp settles with a sharp line of demarcation between solids and a relatively clear supernatant liquid. Essentially all the solids, regardless of their fineness, pass into the thickened underflow, and a clear overflow is separated. In classification, on the other hand, the interparti-cle forces are relatively insignificant as compared to the settling force on the individual particles, and are insufficient to prevent independent movement of the particles. The coarsest, heaviest particles settle most rapidly through the pulp, passing more slowly settling fines. Particles coarser than the mesh-of-separation essentially all settle into the underflow, but if the feed contains any particles finer than the mesh of separation, at least part of them will appear in the overflow. A clear supernatant or overflow can be obtained only if there are no undersize particles present in the feed. Thus it will be seen that classification is impossible under ideal thickening conditions. The finer particles are pulled down at essentially the same rate as coarser particles, and there is no separation on the basis of particle size. The surface attraction holding the particles together in a thickener is usually feeble. Whenever the sedimentation force on any particle is strong with respect to the interparticle forces, that particle can pass through the tenuous structure and settle independently. There are at least four ways of making the sedimentation force strong, with respect to the interparticle forces, and obtaining classification. First, and most obvious, the particles may be large and heavy. Thus coarse sands settle out in a beaker or Dorr thickener ahead of the rest of the thickening solids. Second, the interparticle forces may be altered by physicochemical means; i.e., it is often necessary to add dispersing agents to destroy the interparticle forces and permit classification to take place. Third, the interparticle forces may be reduced by dilution of pulp. It is well known that to obtain the most efficient separation of

Jan 1, 1954

By C. E. Sims, F. W. Boulger, H. A. Saller

Most of the data on equilibrium constant and the deoxidations potentialities of those elements, considered to be stronger deoxidizers for steel than is silicon, have been calculated from thermodynamic data. The reason for this is, primarily, the obvious difficulty of obtaining direct experimental evidence of equivalent accuracy. This is an excellent use of the principles of thermodynamics and has given valuable data not otherwise available. Such results, of course, can be no more accurate than the physical constants used in the calculations, and one can never be sure that the basic data are either complete or accurate. In fact, as in the case with silicon,1 there are not only discrepancies among the calculated theoretical values of the equilibrium constant for deoxidation of steel but also between the theoretical and experimental values. It is highly desirable, therefore, to obtain experimental values for checks on calculated results whenever possible. If they disagree, both cannot be right, but if there is good agreement, their value is enhanced. The present work was done in an effort to obtain experimental evidence in regard to some of the common alloying additions but more particularly the so-called "strong" deoxidizers for steel. The method used was to determine the minimum concentration of the deoxidizer that would effect a certain definite degree of deoxidation in steel. The criterion of deoxidation was the change from the large globular Type I sulphide to the eutectic Type II as described by Sims and Dahle.2 This change is sharp and definite, and inasmuch as it can be produced with equal facility by aluminum, zirconium, and titanium, it is considered a manifestation of a certain degree of deoxidation and not an alloying effect. Ostensibly such a procedure could give only a comparison of deoxidizing powers and no absolute values. Nevertheless, repeated observations have shown that, when increasing increments of aluminum are added to a steel, the residual aluminum content begins to increase simultaneously with the appearance of Type II inclusions. Thus it seems warranted to postulate that the Type II inclusions appear coincident with the virtual elimination of FeO as an active constituent of the steel. Experimental Procedure The data obtained were primarily from the microexamination of polished and unetched specimens and from chemical analysis. Experimental heats weighing 200 to 250 lb were made in a basic-lined high-frequency induction furnace. The base composition was nominally that of a medium-carbon casting steel to which the appropriate additions were made. Specimens were poured into sand-cast ingots 3 in. in diam as shown in Fig 1. Sand-cast ingots were used to prevent chilling and to allow sufficient time in freezing for normal inclusions to form of a size large enough to be studied readily. In the first few heats, the tapered wall ingot was used, but in the majority, the extra large riser was used to prevent piping in heavily deoxidized steels. Specimens for microexamination were taken from the location shown in Fig 1, and drillings for chemical analysis were taken from a similar location. The procedure was to melt the base composition and deoxidize with the usual manganese and silicon additions and then to pour an ingot. The furnace was then tilted back, and the first increment of strong deoxidizer or special alloy was added and allowed to disseminate through the melt, with enough power on to hold the temperature constant, for 45 sec. Then a second ingot was poured. After this, another increment was added, and after the same holding time another ingot was poured. In this way from 9 to 12 ingots were poured from each heat, each successive ingot having progressively larger total additions of alloy. Eighteen heats were made altogether, and the range of alloys used and additions made are outlined in Table 1. The three principal types of sulphide inclusions found are illustrated in Fig 2. The globular Type I sulphides are characteristic of silicon-killed steels, the eutectic Type II are characteristic of steels deoxidized with a small amount of aluminum, while the larger, angular Type III are usually found in steels with a residual aluminum content above about 0.02 pct. In all specimens studied, the transition from Type I to II either did not occur at all or was very abrupt and clear cut. There never was any doubt as to just which increment produced the change, although the individual additions were small, in the order of 0.01 pct. The change from Type II to Type III was considerably less sharp, and, in some cases, both types were found together. Inasmuch as the formation of Type III sulphides is apparently not a deoxidation phenomenon, they will not be discussed here.

Jan 1, 1950

By P. Duwez, C. B. Jordan

A. J. SHALER*—I should like to congratulate the authors for having carried out such a precise set of experiments. It has been found useful, in sintering experimental compacts in vacuo, to make certain that the residual gas is not one which reacts with the metal. Since traces of oxygen can be kept away only with great difficulty, the technique is often adopted of using a "getter " of powder in the vicinity of the compacts, and, in addition, of permitting a small hydrogen leak to flow into the vacuum chamber. Did the authors use similar devices? This paper brings up a question concerning the definition of the word ' sintering.' The authors restrict its use to the adhesion between particles. Kuczynski, in a paper presented at this meeting, applies the word to the growth of areas of contact between particles. I have used it to mean both these phenomena and also the dimensional changes which continue to take place after the first two have run their course. May I suggest that we should come to an agreement on the use of these words ? Fig 1 and 2 show an interesting feature: extrapolation of the curves to zero time does not give a densification parameter of zero. The higher the temperature, the higher is the intercept on that axis. These observations agree with the concept of a practically instantaneous densification taking place while the compact is being brought to heat. Such a change may be brought about by plastic deformation and primary creep. The stress pattern causing this first rapid flow is, to my mind, due to the force of attraction between the surfaces of opposite particles in the regions immediately flanking their common areas of contact. The stress is not temperature-sensitive, but at room temperature plastic deformation only proceeds until the metal in the area of contact can support it elastically. As the metal is heated, the elastic limit falls, and further plastic flow occurs. At the higher temperatures, this is followed by primary creep, and finally by the steady-state rate-reaction which the authors are seeking. If they were to recalculate their densification-parameter values, using, not the initial density of the cold compact, but the density after the compacts have been brought to temperature, the systematic deviations from linearity in Fig 3 and 4 might be eliminated. Such initial densities might be obtained by extrapolating the curves of Fig 1 and 2 to zero time. I am naturally pleased to see that such a very well done series of experiments leads to a heat of activation (for the densification process in hydrogen) that is much higher than that for self-diffusion, in confirmation of the less elaborate results reported by Wulff and myself (Ind. and Eng. Chem., (1948) 40, 838). J. T. KEMP*—I would like to comment on Dr. Shaler's remarks. There are apparently different interpretations of the word "sintering." It seems to me that an accurate definition of our word is essential in all metallurgy. May I point out, in this connection, that in practical metallurgy the word "sintering" has been applied to a bonding process in the preparation of ores and flue dust for fur-nacing. It would be unfortunate if in the area of powdered metallurgy we should establish a definition that is essentially different in meaning. F. N. RHINES*—I think that I can answer the question by saying that I see no essential difference between the use of the term "sintering" in extractive metallurgy and in powder metallurgy; physically the same things are going on. I admit sintering is used for different end purposes in the two cases. When we resort to the sintering of lead ore mixture we are doing so to obtain a chemically reactive, loose texture of some rigidity. This is only a difference in use. After all, in powder metallurgy we sometimes deliberately produce a very porous material which has just a little strength, just as in the case of sinter cake. P. DUWEZ (authors' reply)—We agree that it would be helpful to have well-established definitions of such terms as "sintering." Since the question has now been raised, the time might be appropriate for its consideration by some suitable committee of one or more of the metallurgical societies. In answer to Dr. Shaler's first question, no getter nor hydrogen leak was used in our vacuum experiments, except insofar as the guard disks (used to reduce friction between specimens and trays) may have acted as getters. Dr. Shaler's statement that extrapolation of the curves of Fig 1 and 2 does not lead to zero densification at zero time apparently overlooks the logarithmic

Jan 1, 1950

By Shiou-Chuan Sun

THE presence of an excessive amount of tough froth in the flotation of minerals, particularly coals, may create trouble in dewatering, filtering, and handling. Froth is also a nuisance in many chemical industries.' This paper presents a study on the destruction of extremely tough froths with intense high-frequency sound. The data indicate that sound waves can be employed for continuous atandsoundwavescan instantaneous defrothing. A powerful high-frequency siren was used in obtaining the data. Also tested was an ultrasonorator of the crystal type with a frequency range of 400, 700, 1000, and 1500 kc per sec and a maximum power output from its amplifier of 198 w. The results, not presented, indicate that as now designed this machine is not suitable for defrothing. Although the sound generators of the magnetostriction type2,3 and of the electromagnetic type'.' were not available, it is beelectromagneticlieved they are capable of producing the required sound intensity for defrothing. The use of ultrasonics for defrothing was suggested by Ross and McBain1 in 1944. Ramsey8 reported in 1948 that E. H. Rose mentioned a supersonic device that broke down flotation froth but with low capacity. The writer has not been able to find any published literature containing practical experiments. Theoretical Considerations The mechanism of defrothing by sound is attributed to the periodically collapsing force of the propagated sound waves and the induced resonant vibration of the bubbles. The collapse of froth is further facilitated by the sonic wind and the heat of the siren. Sound waves can exert a radiation pressure'," against any obstacle upon which they impinge. When a froth surface is subjected to the periodic puncturing of sound waves, the bubbles are broken. According to Rayleigh9 and Bergmann,12 the radiation pressure of sound, P, in dynes per sq cm is given as: P = 1/2 (r+1)i/v where r is the ratio of the specific heats of the medium through which sound is traveling and is equal to 1 on the basis of Boyle's law; i is the sound intensity in ergs per sec per sq cm, and v is the sound velocity in cm per sec. In this case, the accuracy of the formula is only approximate, because a perfect reflection can hardly result from a column of froth. In addition to the radiation pressure, the propagated sound waves cause the bubbles of the froth to have a resonant vibration.'" he vibratory motion of the bubbles causes collision and coalescence, thereby weakening if not breaking the bubble walls. Sonic wind and heat were also generated." The sonic wind can exert pressure on the froth surface, and the heat can evaporate the moisture content of the bubble walls as well as expand the enclosed air. Apparatus The defrothing apparatus, shown in Figs. 1 and 2, consists of a powerful high-frequency siren, a glass or stainless steel beaker of 2-liter capacity with 12.4 cm diam and 17.1 cm height, and a metal reflector. The beaker was placed 2 in. above the top point of the siren. The metal reflector was adjusted to reflect and focus the generated sound waves into the central part of the beaker. Fig. 2 shows the crystal probe microphone used to measure the acoustic intensity and the mandler bacteriological filter employed to introduce compressed air into the beaker for frothing. The apparatus was enclosed in a soundproof cabinet equipped with a glass window. The siren, shown in Fig. 3, consists of a rotor that interrupts the flow of air through the orifices in a stator. The rotor, a 6-in. diam disk with 100 equally spaced slots, is driven by a 2/3 hp, Dumore W2 motor at 133 rps. The frequency of the siren can be varied from 3 to 34 kc. The maximum chamber pressure is about 2 atm, yielding acoustic outputs of approximately 2 kw at an efficiency of about 20 pct. The siren itself is relatively small and can be operated in any orientation. A detailed description of the siren has been given by Allen and Rudnick.11 Collapse of Froth To study the sequence of the collapse of froth, the glass beaker was partially filled with 920 cc water, 100 g of —150 mesh bituminous coal, 0.3 cc petroleum light oil, 0.2 cc pine oil and 1.54 cc Pyrene foam compound. This mineral pulp was agitated for 5 min and then aerated through a mandler filter until the empty space of the beaker, approximately 9 cm high, was filled completely with min-

Jan 1, 1952

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995

By D. O. Hobson

Zirconium single crystals of various specific orientations were fabricated by rolling or drawing. The resulting textures were determined and are discussed with respect to the deformation modes that produced them. The crystals deformed in a predictable manner by combinations of up to third-order twinning with three twinning modes and by slip. Twinning was found to play a major role in initial texture formation. Texture changes produced by slip occurred only at the higher reductions. The twinning sequences that produced each intensity peak during the initial reductions could be identified. Schmid factor criteria were found useful in predicting which deformation modes to expect for each crystal orientation and fabrication procedure. The possible application of these data to poly-crystalline material is discussed. PREFERRED orientation or texture has a significant effect on the properties of most materials, causing anisotropy in fabricated cubic metals and enhancing the natural anisotropy of noncubic metals. This study evaluates the effects of several fabrication methods on the textures formed from specific starting orientations of zirconium single crystals and, it is hoped, gives an insight into the effects of the same operations on poly-crystalline material. BACKGROUND In fcc and bcc metals, texture changes take place by gradual lattice rotations caused by the operation of one or more slip systems. Deformation twinning plays an insignificant role in the deformation of such metals. In zirconium and its alloys, however, and in many other hep metals the ability to twin allows very rapid texture changes to be made with very small amounts of deformation. The deformation systems found in zirconium and its alloys are prism slip and three twinning modes.1 Slip occurs on the {1010}< 1120) system. There is little or no appreciable basal slip in zirconium. The twinning planes, illustrated in Fig. 1, are {1012}, {ll2l}, and {1122}. Two twinning modes, the {1012} and the {ll2l} operate for a tensile stress along the basal pole. A compressive stress parallel to the basal pole is required for {ll22} twinning. These twinning operations cause a 35- to 85-deg reorientation of the basal pole. The {1012} twin is the predominant tensile twin at room temperature. The twinning shears, S, are shown in the figure. A criterion for predicting which deformation system will operate when a grain is subjected to a known stress state is the Schmid (orientation) factor. This factor gives the fraction of the applied stress that computer program was written2 to calculate the Schmid factors for the four deformation modes in zirconium. It assumed three orthogonal stress axes and considered ninety-one different orientations of the basal pole in one octant of this stress space. At each basal pole position the Schmid factors were calculated for seven positions of rotation at 10-deg increments of the unit cell about the basal pole. Schmid factors were determined for a total of 637 orientations and for twenty-four deformation systems in each orientation. The program listed the Schmid factors for uniaxial stress parallel to each axis and, to approximate rolling, or-thonormal biaxial stress was also considered. Fig. 2 shows the range of orientations over which the various types of deformation would tend to predominate in biaxial plane strain with the stresses, equal magnitude. The exact boundary position between regions of different deformation modes depends, however, on the relative values of the critical shear stress for each deformation mode. Fig. 2 is drawn on the assumption that they are equal and it therefore may be only approximately correct. It is also recognized that the biaxial stress analysis may not be applicable in certain crystal orientations. EXPERIMENTAL PROCEDURE Single crystals of zone-refined zirconium, produced by Wilson of this Laboratory,3 were electrical-discharge-machined to form specimens for rolling, tube-drawing, and rod-drawing studies. Specimens were rolled at room temperature on 2-|--in.-diam hand-powered rolls from three different starting orientations: 1) the basal plane parallel to the rolling plane and the [1120] in the rolling direction, (0001)[ll20]; 2) the (1120) plane parallel to the rolling plane and the basal pole in the rolling direction, (1120)[0001]; and 3)_the (1120) plane parallel to the rolling plane and the [1100] in the rolling direction, (1120)[ll00]. Drawing specimens were cut with the [0001] direction as the drawing direction in the tube blank and [1120] as the drawing direction in the rod specimen. The drawing

Jan 1, 1969

By F. Selig, A. S. Odeh

A second-order approximation to the exact solution of the diffusivity equation corresponding to the pressure build-up of a well producing at a variable rate is derived. This approximation is applicable when the well&apos;s shut-in time is larger than the total time elapsed since the well was first produced. The resulting equations are compact in form and easy to use. Thus, the need for Horner&apos;s&apos; theoretically precise but rather laborious solution to the above problem is eliminated. In addition, these equations apply where the use of Horner&apos;s widely known approximate method is questionable. From a practical point of view, the reported method is best suited for analysis of drill-stem tests and short production tests conducted on new wells. INTRODUCTION The utility of drill-stem and short production tests in reservoir studies has long been recognized by the reservoir engineer. If interpreted correctly they could lead to a wealth of information upon which may depend the success or failure of reservoirs&apos; analyses. Initial reservoir pressure and the average flow capacity are two quantities that are normally sought from a drill-stem and/or a short production test analysis. Pressures are the most valuable and useful data in reservoir engineering. Directly or indirectly, they enter into all phases of reservoir engineering calculations. Therefore, their accurate determination is of utmost importance. The flow capacity kh of the reservoir is indicative of its commercial capability. In addition, it can indicate the presence of a darnaged zone around the wellbore and, thus, the necessity for remedial measures. Of the several methods used to analyze drill-stem and short production tests, Horner&apos;s&apos; method is by and large the most common. It applies to an infinite reservoir and or a limited reservoir where the effect of production has not been felt by the boundary. Horner&apos;s method makes use of the so-called "point-source" solution of the diffusivity equation. The point-source solution is approximated by a logarithmic function and the superposition theorem is utilized to give the familiar pressure build-up equation where is the shut-in time, q is in reservoir barrels per day and the rest of the symbols conform with AIME nomenclature. Eq. 1 was derived for a well which produced at a constant rate q from time zero to time t and was then shut in. In actuality, such a constant rate of production does not normally obtain. Therefore, a correction must be applied to Eq. 1 to account for the varying rates of production. Horner suggested two methods. The first, which results in a theoretically accurate solution, is rather lengthy and laborious and, thus, it is not suited for routine analysis. The second which has been termed a "good working approximation" is the one used by the majority of the reservoir engineers. In the second method, Eq. 1 is modified by simply introducing a corrected time t, and writing where q is the last established production rate prior to shut-in, and t, is obtained by dividing the total cumulative production by the last established rate. Horner&apos;s original paper does not give any indication that this method of correction is based on any theoretical justification. In addition, there is a question as to what constitutes the last established rate. In case of a drill-stem test some engineers use the average rate obtained by dividing the total fluid produced by the total flow time, while others calculate the average rate by dividing the total fluid produced by the last flow-period time. Obviously, different results obtain for the different flow rates used. Because of this, a simple method to the varying-rate case was developed which is theoretically sound and which defines clearly the flow rate and its associated time to be used in the calculations. The final equation arrived at is where q* and t* are a modified rate and time, respectively, and can be easily calculated. In addition, it is shown theoretically that Horner&apos;s approximate method, if used for a variable-rate case, gives the correct pressure but would not be expected to give the correct flow capacity. MATHEMATICAL ANALYSIS The general equation governing the flow of slightly compressible fluid in porous media may be written as The elementary solution to Eq. 4, representing an instantaneous withdrawal of Q units volume of fluid at the origin at t = 0, is known as the instantaneous sink

By Pol Duwez

IN the course of an investigation of the V-CO system, two intermediate phases were found. One of these phases corresponds approximately to the stoichiometric composition VCo and is isomorphous with the sigma phase in the Fe-Cr system.&apos; The second phase has the composition V3Co; its crystal structure is described in the present note. The alloys were prepared by mixing the two metals in the powder form, pressing a small disk weighing about 5 g at 80,000 psi, and arc melting this disk on a water-cooled copper plate in an atmosphere of pure helium. The details of this technique have been described.&apos; The vanadium powder was obtained from Westinghouse Electric Corp., Bloomfield, N. J. This powder is probably of very high purity, since when it is properly sintered or melted in the above-mentioned arc furnace, ductile specimens are obtained. The cobalt powder, from Charles Hardy, Inc., New York, contained 0.5 pct Ni, 0.1 pct Cr, and traces of Si and Fe. After melting, the V,Co samples were sealed in evacuated quartz tubes and homogenized for ten days at 800°C. Powder diffraction patterns were obtained with a 14.32 cm diam camera, using Ka copper radiation. The patterns were readily indexed on the basis of a primitive cubic lattice with a parameter equal to 4.675A. The density, determined by the immersion method, was 6.71 g per cu cm; hence the number of molecules per unit cell is approximately 1.95; i.e., 2. At this point, the possibility that the structure might be that of beta tungstena became apparent. The beta tungsten structure is described as follows: Space group 03,, — Pm3n 2 Co in (a) : 000; ?4lhYZ (hhl) reflection present only if 1 = 2n. Assuming this structure to be the correct one, intensities were computed by means of the usual eauation: 1 + cos220 I oc p F sin 0 cos 6 where F is the structure factor, 0 the Bragg angle, and p the multiplicity factor. The observed and calculated values of sin 0 and the intensities are given in Table I. The agreement between the observed and the calculated sin 0 is good and there are no flagrant discrepancies between the calculated intensities and those estimated visually. The (hhl) reflections for which 1 is odd are not observed, as required by the space group. In addition, the (410), (430), and (531) reflections are missing as expected, because of the special (a) and (c) positions in0%. However, six reflections—(llo), (220), (310), (411), (422), and (510)—which have very weak computed intensities were not observed. For these reflections, the structure factor is proportional to the difference between the scattering factors of the two atoms in the structure. Since the scattering factors of vanadium and cobalt are not very different, these reflections are weak. However, by using Ka chromium radiation, whose wavelength is just above the absorption edge of vanadium, the effective scattering factor of vanadium may be decreased by one or two units; consequently the difference between the cobalt and vanadium scattering factors is increased. It was, indeed, found that in a powder pattern taken with chromium Ka radiation, the three reflections (110), (220), and (310) were actually present. The three other reflections (411), (422), and (510), with spacings smaller than half the wavelength of chromium Ka, were obviously not obtainable with chromium radiation. All the experimental results appear to confirm the beta tungsten structure for V,Co. In this structure, each cobalt atom is surrounded by twelve vanadium atoms at 2.61A; each vanadium atom is surrounded by two vanadium atoms at 2.34A, four cobalt atoms at 2.61 A, and eight vanadium atoms at 2.86A. Acknowledgment This work was done at the Jet Propulsion Laboratory, California Institute of Technology, under contract number W-04-200-ORD-455 with the Army Ordnance Department, Washington, D. C. The author wishes to thank this agency for the permission to publish the results of this investigation. References &apos;P. Duwez and S. R. Baen: X-Ray Study of the Sigma Phase in Various Alloy Systems. Symposium on the Nature, Occurrence, and Effect of Sigma Phase. ASTM Special Tech. Pub. No. 110, pp. 48-54. Philadelphia, 1951. 2 C. H. Schramm, P. Gordon, and A. R. Kaufmann: The Alloy Systems Uranium-Tungsten, Uranium-Tantalum, and Tungsten-Tantalum. Trans. AIME (1950) 188, pp. 195-204; Journal of Metals (January 1950). 3 M. C. Neuburger: The Crystal Structure and Lattice Constants of Alpha and Beta Tungsten. Ztsch. fiir Krist. (1933) 85, pp. 232-237.

Jan 1, 1952

By C. E. Birchenall, C L. McCabe

IN attempting to extend vapor pressure measurements of the type previously reported by Schadel and Birchenall1 for silver and by Schadel, Derge, and Birchenall&apos; for silver-silicon to other systems, it was observed that the materials melted at indicated temperatures 10" to 15" below their accepted melting points. Further investigation revealed that the thermocouple readings were in error due to appreciable conduction losses along the reference thermocouple wires. If the wire diameter of the reference couple inserted into the Knudsen cell was reduced, the correction for the indicating couple changed in a manner tending to explain the melting behavior. When extrapolated to zero wire diameter from measurements with several reference thermocouples of different wire thickness, the melting point of silver then agreed with the indicated temperature at which silver chips were observed to coalesce into a sphere. Approximately the same calibration was given by observing the melting of small wires of silver or gold in the Knudsen cell connected in series with an ammeter, where the leads into the cell were very fine in order to minimize heat conduction. Unfortunately neither of these methods seemed to yield a sufficiently precise temperature calibration to match the apparent precision of the other aspects of the vapor pressure measurement. It was decided. therefore, to redetermine the vapor pressure of silver in another setup under conditions permitting precise temperature measurement. The vapor pressure of pure silver could then be used as an internal calibration of temperature in the older unit in making runs on alloys. This has been done; the present report is a correction to ref. 1. Experimental Procedure The apparatus, shown in Fig. 1, was very similar to that employed by Harteck,3 except that the orifice sizes were smaller and the residual pressure in the vacuum system was probably much lower. A small, sharp-edged hole, nearly circular in shape, was ground into the rounded end of a quartz tube. The orifice area was then measured by tracing the image at known magnification on graph paper and counting the squares enclosed. The silver specimen was sealed into the tube to make a Knudsen cell. A tantalum jacket surrounding the cell served to increase the uniformity of temperature. This assembly was placed in the bottom of a long quartz tube with an inside diameter of about 1 in., which was connected to the vacuum system through a ground joint sealed with picein wax well removed from the furnace. A thermocouple tube inserted through the top of the vacuum line reached into the tantalum jacket so that the thermocouple junction was immediately adjacent to the Knudsen cell except for the protection tube wall. A resistance furnace could be raised to cover the end of the quartz tube containing the cell in such a way that the cell was in the uniform temperature zone 13 in. from the end of the furnace. An ionization gage was included in the vacuum system in the cold lines of wide diameter, immediately beyond the ground joint. The vacuum system consisted of a mercury one-stage diffusion pump, backed by a Welch duo-seal mechanical pump. The pumps were separated from the reactor chamber by a dry ice trap. The ionization gage always read less than 10-5 mm Hg after initial outgassing and before each run was started. Each newly filled Knudsen cell was evacuated at high temperature overnight before the first weighing was made. The cell was returned to the system, heated for a measured time at constant temperature, cooled, and reweighed. The heating and cooling times were quite short since the hot furnace was raised to receive the reactor at the beginning of the run and removed again at the end. The tube heated or cooled quickly. The total mass loss was attributed entirely to effusion of silver vapor from the quartz cell, since empty quartz cells maintained constant mass through similar heating cycles. The vaporized silver condensed on the cold walls of the quartz tube extending above the furnace. Earlier studies in the induction heated unit had shown that the same vapor pressure was found for silver, whether the silver was in contact with the tantalum metal cell or with porcelain or quartz liners. The Pt-Pt-10 pct Rh thermocouple was calibrated against a secondary standard of the same material and found to agree with the published tables. Always operating in air at temperatures below 100O°C,

Jan 1, 1954

The United StatesÆ reporting standard for the mining industry for securities purposes is contained in the Security and Exchange CommissionÆs Industry Guide 7. It defines proven and probable Reserves using its own definitions, and prohibits the disclosure of quantitative estimates, for all mineralisation other than those two Reserve categories (though disclosure of Measured and Indicated Resources as quantitative mineralised material estimates is now informally allowed). Similarly, it restricts disclosure of value estimates to Reserves only, which SEC policy generally requires to be on an historic cost accounting basis. The SEC does not maintain a formal Competent or Qualified Person policy. In March 1999, the US-based Society of Mining, Metallurgy and Exploration (SME) released an update of its 1991 guidelines for definitions to be used in reporting of Mineral Resources, Reserves and Exploration Information, closely abiding by the 1997 CMMI recommendations. However, without SEC recognition, reporting under the SME and CMMI definitions is effectively barred for US companies. The SEC intends to adopt the International Financial Reporting Standards (IFRS) of the International Accounting Standards Board (IASB). This will occur within just a few years, when the convergence project for development of the IFRS has reached a satisfactory point. The US is the largest financial supporter and participator in IASB. The Extractive Industries Standard of the IFRS will likely terminate Industry Guide 7. However, the effect of this international replacement will likely be equally restrictive. This could possibly neutralise the benefit of a CMMI-based global reporting standard. SME, the US society encompassing the widest range of mining industry professionals, does not have a Code of Ethics. It has no mechanism for requiring members to abide by a professional standard. SME is presently looking into possible solutions for this deficiency. US-based professional societies that do have a binding Code of Ethics, generally cater to a single profession, and are not just mining industry related. The American Institute of Professional Geologists (AIPG) and the American Institute of Minerals Appraisers (AIMA) are examples. The SME is considering creating a subsidiary body with an enforceable Code of Ethics. To support a CMMI-based global reporting standard, competent persons will need to work across international borders. A standardised mechanism for qualifying and registering competent persons will be needed. National rules and laws must allow competent persons to easily enter countries to perform their work. State issued licenses are increasingly required for much of the work performed in the US mining industry by engineers, geologists and minerals appraisers (valuers). Such licenses are not required by the SEC for Reserve reporting in the US, may not be required for valuation of mineral properties under certain circumstances, and except for real property valuer licenses, they generally do not have a binding code of conduct. However, state licensing of professionals forms a substantial and increasing barrier to interstate trade in professional services, and can be a prohibitive barrier to professionals from outside the US. Any rationalisation of this confusing patchwork of regulations confronting US minerals industry practitioners will only occur as part of larger, national change, hopefully aimed at compliance with international standards and protocols. The US does not have a valuation standard aimed specifically at the mining industry. The Uniform Standards of Professional Appraisal Practice, the national valuation standards, often must be applied to mineral property valuation, but contains no specific instructions for minerals. The author has campaigned against development of minerals valuation standards proposed by US minerals institutes. Instead he encourages the mining industry worldwide to place its support behind the initiative of the International Valuation Standards Committee (IVSC) to include an extractive industries section in its International Valuation Standards (IVS). This should provide a global set of valuation standards for the mining and petroleum industry within two years. This addition to IVS will provide essential valuation standards reference support for the extractive industries financial reporting standard of the International Accounting Standards Board. The IVS has achieved a high level of acceptance in the developed and lesser developed countries of the world. It provides a comprehensive framework of Generally Accepted Valuation Principles for the valuation profession internationally, for valuation of all property or asset types. IVSC is effectively a sister organisation to IASB. The IASBÆs International Financial Reporting Standards (IFRS), previously known as the International Accounting Standards (IAS), reference and quote IVS in some instructions for determination of fair value. IVSC is a non-governmental organisation (NGO) member of the United Nations and maintains liaison with many important international economic, accounting and financial agencies, such as the OECD, IMF and WTO.

Jan 1, 2002

By W. Allen

FOR the past six years gravity surveys have been used for underground prospecting in the copper mines at Bisbee, Ariz. The primary purpose of the surveys has been to reduce the diamond drilling and crosscutting necessary for exploration. Since many of the orebodies are small, and geologic control is not always apparent, any information that will direct the drilling and crosscutting is highly desirable. Because of extensive development and exploration work in the copper mines at Bisbee, it has been possible to cover more than 630,000 ft of crosscuts on 30 levels with the gravity surveys. In the process the gravity procedures have been refined to a high degree. Density Contrast: For a gravity survey to be successful, a sufficient density contrast must exist between the geologic feature sought and surrounding host rocks. Most mineralized areas will provide this contrast if fairly massive bodies are present. In the Bisbee area the entire sequence of formations, except for alluvium, appears to have specific gravities ranging from 2.65 to 2.70. These values have been determined by means of a large number of cut samples and diamond drill cores. As a further check, vertical gravity differences have been used where nonmineralized sections are known to occur.&apos; The only known major gravity disturbances result from mineralization that has increased the density and the voids that have decreased density. The voids are caused by mining operations and by underground water movement that has developed several areas of caverns. Equipment: While not absolutely essential, a small rugged gravity meter, such as the Worden meter, is highly desirable. A tall tripod, about the height of a transit tripod, permits instrument set-ups in deep water and in locations where fallen timber and muck piles make it impossible to use a short tripod. An additional advantage of a tall tripod is that it places the meter in the center of the crosscut, reducing the error caused by the crosscut void. Size and weight are important, since the only satisfactory means of operating the meter underground is to carry it by hand. A backpack can be used in rare instances but is usually a hindrance because of the close station spacing. The operator&apos;s ability to move through tight clearances will improve survey coverage, as it is then possible to move through raises and caved areas and to pass mine cars and machinery with a minimum of trouble. Station Control: Gravity stations are normally located every 100 ft along the crosscuts, at each intersection, and in the face of all stub crosscuts. In areas of high gravity relief, or where small anomalies might be expected, stations may be located at 25 or 50-ft intervals. When possible, the stations should be offset to avoid effects of raises or other voids. The gravity stations on a level are tied to one or more base stations, which are usually located at the shaft or near the portal of an adit. The base stations may be part of a gravity control net that extends to each level in the mine as well as to the surface. Such a net extending throughout the potential area of the surveys is highly desirable, as it is then possible to compare all gravity stations on a uniform basis. The stations that are part of the base net should be carefully established by multiple readings and, if necessary, by a least squares adjustment of the loops. In some instances where levels do not have a shaft station, or where access may be blocked by caving, it may be necessary to establish secondary bases at the top and bottom of the raises that are between levels. Under fair conditions 70 to 90 gravity stations can be located and run in 6 hr by a two-man crew. The best field procedures depend on conditions. Reduction of Field Data: Most of the time required to produce a final gravity map is consumed in processing the data. Each meter reading must be corrected for a minimum of five factors that affect the gravity value in addition to the density contrast being sought. These factors are 1) instrumental drift, 2) station elevation, 3) topography, 4) latitude, and 5) regional gravity gradient. Mine openings, such as stopes and raises, will affect the value. However, it is seldom practical to make corrections for these voids. Usually a rotation is made on the field note on the station, and any

Jan 1, 1957

By A. P. Svenningsen

IN the early stages of design it was not considered necessary that separate crushing plants be built for the new sulphide concentrator and smelter until sometime in the future. The plan was to use the existing crushing facilities for both oxide and sulphide ore. A few additions were contemplated for the existing plants, such as increased bin capacity, and possibly two new secondary crushing units. The more the problem was studied and discussed with the plant operators, the more it became evident that it was complex. It involved the classification of different kinds of ore from the open pit mine -sulphide, oxide and mixed-and how best to separate them so that each kind of ore was given the proper processing and treatment. It also involved the problem of keeping the different ores from being contaminated in bins, hoppers and chutes. Added to these, transportation became complicated and would involve additional handling and loading of ore from crushing plants to conveyors, to bins, and finally to railroad cars which were to be hauled to the concentrator and dumped into the fine ore bin. General In the early part of 1951 it was decided that the concentrator be constructed with ten grinding units instead of seven as originally authorized. The smelter was to be increased proportionally and naturally also the overall tonnages of ore to be handled by the new sulphide plant. Due to this increase in plant capacity and the larger tonnages involved, the difficulties which would arise by using the existing crushing plants were increased to a point where it became evident that the building of new crushing plants for sulphide ore exclusively was technically, as well as economically, advantageous. Authorization was, therefore, given by the company to construct new crushing plants to handle 30,000 tons of ore per day, and capable of reducing the run-of-open-pit ore to the proper size feed for the 10x14-ft rod mills in the concentrator. The ore, mined in the open pit, sometimes comes in pieces as large as 6 to 7 ft diam. The rod mills may call for ore crushed to 3/4 in. The large .size of ore delivered from the open pit determined that a 60-in. gyratory crusher be used as primary breaker. Such a crusher will have a capacity considerably in excess of 30,000 tons per day. The crusher will be a single discharge unit driven by a 500-hp electric motor through a tear coupling and a floating shaft. This type of drive has proven successful at a number of other crusher installations which our company has operating in the United States, Mexico and South America. The tear coupling will protect both the crusher and motor against damage in case of overload. No new features are incorporated in the design of the crusher itself, except that the, discharge chute is made the full width of the crusher with parallel sides instead of the usual converging sides. This change in detail should eliminate, a feature which has been a bottleneck in some of the operating plants and has caused loss of production due to ore hanging up and blocking the chute. The secondary crushing plants will have three 7-ft standard Symons cone crushers and six 7-ft short head Symons crushers. Between the primary and secondary crushing plants a coarse ore bin will be constructed with a nominal draw-off capacity of 30,000 tons of ore. The standard Symons and the short head Symons will be in separate buildings. All the crushing plants and the coarse ore bin are interconnected with conveyor belts for transporting the ore to the crushers at the tonnage rate desired. The final product of the new crushing plants is produced by the short head crushers. It will be delivered onto a conveyor belt leading to the top of the fines ore bin in the concentrator. A separate conveyor belt running the full length of the fines ore bin and provided with a movable tripper of rugged design will discharge the sulphide ore into the bin. The concentrator bin is planned and designed so that the installation of this additional conveyor will not interfere with the operation of the two railroad tracks on which crushed ore is brought from the existing oxide plant. Thus when completed the bin can be filled simultaneously by ore from the new crushing plant and by ore from the existing leaching plant.

Jan 1, 1952

By L. H. Van Vlack, T. Y. Tien, R. J. Martin

The phase relationships of the MnTe-MnS system were studied by DTA procedures. There is an eutectic at 810°C with about 10 mole pct MnS-90 mole pct MnTe. An eutectoid occurs at about 710°C with approximately 7 mole pct MnS where the MnTe(NaCl) solid solution dissociates on cooling to MnTe(NiAs) and MnS. There is very little solid solubility of MnTe in MnS. ALTHOUGH MnS may exist in three different crystal forms,&apos; only the NaC1-type phase is stable.2 Above 1040°C, MnTe also has the cubic NaC1-type structure. Below that temperature, MnTe changes to the NiAs-type structure.3 This phase transition is rapid for both heating and cooling. As a result the high-temperature crystal form of MnTe cannot be retained at room temperature. Because MnO, MnS, and MnSe are all stable with the NaC1-type structure, and MnTe has this structure at high temperatures,4 solid solution formation could be expected among these compounds. It is interesting to note, however, that a complete series of solid solutions exist only in the MnS-MnSe system,&apos; and that the solid solution is quite limited in the MnO-MnS system.&apos; The MnSe-MnTe system possesses a complete series of solid solutions at high temperatures with separation at lower temperatures.7 Although ion size may be critical in the miscibility of MnO-MnS, it is quite possible that the bond type plays a more important role with the miscibility of MnSe-MnTe. This would permit us to speculate that the miscibility gap would be extensive in the MnTe-MnS system. EXPERIMENTAL Preparation. The samples were prepared by mixing and compacting MnTe and MnS powders. The MnS was previously prepared through the sulfur reduction of Mnso4.8 The MnTe had been prepared by mixing and compacting double vacuum distilled metallic manganese and high-purity tellurium in stoichiometric ratio modified with 1 wt pct excess tellurium. The compacted powders were put in a graphite crucible which was sealed in an evacuated vycor tube. The free space in the vycor tube was made minimal to reduce the loss of tellurium. The sealed assembly was then heated slowly to about 500° C where the free manganese and tellurium reacted vigorously, melting the MnTe which formed. Only one phase, MnTe, was detected by X-ray powder patterns and metallographic techniques. Each compact of MnTe-MnS was placed in a graphite crucible and then sealed in an evacuated vycor tube. The samples were heated at 1250°C for 4 hr and furnace-cooled. Microscopic examination revealed no third phase beyond MnS and MnTe. A typical microstructure is presented in Fig. 1. Identification. X-ray powder patterns were obtained using 114.6 mm Debye-Scherrer camera and Fe-Ka radiation. Mixtures of cubic MnS and hexagonal MnTe were observed in all of the compositions prepared. No lattice parameter change was noticed among different compositions, indicating no solid solution could be retained at room temperatures between these two end-members. A lattice parameter of 5.244Å for MnS was obtained by the Nelson and Riley9 extrapolation method using the diffraction lines of (h2 + k2 + 12) equal 12, 16, 20, and 24. The values, a = 4.145Å and c = 6.708Å, for hexagonal MnTe were obtained from the (006) and (220) lines in the back-reflection region. These values agree well with the values reported by Taylor and Kag1e.10 Differential Thermal Analysis. A differential thermal analysis procedure was used to determine phase relationships since the high-temperature equilibrium conditions could not be retained for examination at room temperature, even when the sealed samples (~0.5 g) were quenched in water. The samples were sealed in an evacuated 4 mm vycor tube with a recess in the bottom to accept a thermocouple. An Al2O3 reference was similarly prepared and the two placed within a piece of insulating fire brick to dampen spurious temperature changes within the furnace. The furnace was controlled by a mechanically driven rheostat which increased the temperature at a rate of about 15°C per min. Known phase changes in the Pb-Sn system1&apos; and the a-to-ß quartz inversion12 were used for calibration

Jan 1, 1969

By D. W. Rudd, D. W. Vose, S. Johnson

The permeability of Mo-0.5 pel Ti to hydrogen was investigated over a limited range of temperature and pressuire (709° to 1100°C, 1.i and 2.0 atm). The resulting permeability, p, is found to obey the The experimental data justifies the permeation mechanism as a diffusion contl-olled pnssage of Ilvdrogen atoms through the metal barrier. 1 HE permeability of metals to hydrogen has been investigated by a number of workers and their published results have been tabulated by Barrer&apos; up to 1951. Since most of the work on the permeability has been accomplished prior to this date, the compilation is fairly complete. Mathematical discussion of the permeability process has been reported by Barrer, smithells, and more recently by zener. From these efforts several facts are observed. First, the permeability of metals to diatomic gases involves the passage through the metal of individual atoms of the permeating gas. This is evidenced by the fact that the rate of permeation is directly proportional to the square root of the gas pressure. Second, the gas permeates the lattice of the metal and not along grain boundaries. It was shown by Smithells and Ransley that the rate of permeation through single-crystal iron was the same after the iron had been recrystallized into several smaller crystals. Third, it has been observed that the rate of permeation is inversely proportional to the thickness of the metal membrane. Johnson and Larose5 verified these phenomena by measurirlg the permeation of oxygen through silver foils of various thicknesses. Similar findings were noted by Lombard6 for the system H-Ni and by Lewkonja and Baukloh7 for H-Fe. Finally, it has been determined that for a gas to permeate a metal, activated adsorption of the gas on the metal must take place. Rare gases are not adsorbed by metals, and attempts to measure permeabilities of these gases have proved futile. ~~der&apos; found negative results on the permeability of iron to argon. Also, Baukloh and Kayser found nickel impervious to helium, neon, argon, and krypton. From what was stated above concerning the dependence of the rate on the reciprocal thickness of the metal barrier, it is seen that although adsorption is a very important process, at least in determining whether permeation will or will not ensue, it is not the rate determining process for the common metals. A case in which adsorption is of sufficient inlportance to cause abnormal behavior has been noted in the case of Inconel-hydrogen and various stainless steels.&apos;&apos; APPARATUS The apparatus used in this study is shown in Fig. 1. The membrane is a thin disc (A), but is an integral part of an entire membrane assembly. The entire unit is one piece, being machined from a solid ingot of metal stock. When finished, the membrane assembly is about 5 in. long. Two membrane assemblies were made; the dimensions of the membranes are given in Table I. The wall thickness is large compared to the thickness of the membrane, being on the average in the ratio of 13 to 1. There exists in this design the possibility that some gas may diffuse around the corner section of the membrane where it joins the walls of the membrane assembly, If such an effect is present, it is of a small order of magnitude, as evidenced by the agreement of the values of permeability between the two membranes under the same temperature and pressure. A thermocouple well (B) is drilled to the vicinity of the membrane. The entire membrane assembly is then encased in an Inconel jacket and mounted in a resistance furnace. The interior of the jacket is connected to an auxiliary vacuum pump and is always kept evacuated so that the membrane assembly will suffer no oxidation at the temperatures at which measurements are taken. The advantages of this configuration are: 1) there are no welds about the membrane itself, so that the chance of welding material diffusing into the membrane at elevated temperatures is remote. 2) It is possible to maintain the membrane at a constant temperature. Since the resulting permeation rate is very dependent upon temperature, it is advisable to be as free as possible from all temperature gradients. 3) It is possible to obtain reproducible results using different specimens. The only disadvantage to this configuration is the welds (at C) in the hot zone. The welding of molybdenum to the degree of per-

Jan 1, 1962

By William F. Brandom

INTRODUCTION Cross, et al. (1974), produced a retrospective study of standard setting for underground miners. This report had two distinct components; i) criteria of importance for the protection of the miners, and ii) economic considerations for standard setting. The methods for setting radiation safety standards reviewed were: dose calculations and consensus methods; epidemiology; pathology; bioassay; animal experiments; sputum cytology; chromosome aberrations; and, the Mantel-Bryan Model. By looking back, the authors intended to enable officials to look ahead in making future decisions based on reasonable conclusions. Now it may be time to consider underground miners&apos; protection from another perspective: are there miners who may be especially susceptible to toxic environments?; and if so, are there any biomedical assays that might be indicative of exceptional sensitivities to toxic substances? The human population is genetically very heterogeneous. The data of Saccomanno, et al. (1973), reveal great variability in individual response to radon daughter exposure and only a small portion of the miner population subject to toxic inhalants develop squamous cell metaplasia (Saccomanno, et al., 1970). The majority of the miner population is either not susceptible or is resistant to the toxic agents. This information suggests the existence of a small subpopulation with increased sensitivity or reduced resistance and underscores the need for indicators from biomedical assays that might prove of value for the detection of such individuals. The heightened awareness of the contribution of pollutants in the environment for the potential induction of mutations and carcinogenesis lead to a profusion of short-term bioassays to circumvent the high cost and time-consuming large toxicity animal studies. Over 100 bioassays across taxa from microbes to man are at various stages of use or development (Hollstein, et al., 1979). Less than a dozen tests currently offer early promise for application to[ in vivo] effect studies of man. Many are still in early development, lack the sensitivity needed for a retrospective or prospective study at current permissible exposures, are impractical to conduct in the field, or are not cost effective. The purpose of this paper is to review some of the bioassays that may now, or in the near term, prove applicable for the detection of individual underground miners with increased susceptibility to toxic agents. Throughout this statement, it is assumed that any single test may give false negatives or false positives and, therefore, a tier of tests should be investigated. The possible tests are in various stages of development; some tests better proven than others with a firmer data base and, therefore, with greater probability of usefulness. Some of the less proven assays are not ruled out if they have practical or theoretical promise as indicators. Table I summarizes the assays critiqued for their potential to monitor the effects of [in vivo] exposure to genotoxic substances. POTENTIAL INDICATORS OF HIGHLY SENSITIVE MINERS Assays of Body Fluids It is desirable to have data on the agent(s) to which subjects are exposed when humans are monitored by biomedical effects. Obviously, to varying intensity, the underground mining environments are monitored for radon daughters and it is recognized that the miners are also exposed to other pollutants, most notably, uranium ore dust and diesel fumes. Further testing for the metabolites of the pollutants can be done on body fluid, urine. [High Performance Liquid Chromatography (HPLC)]: This is a very sensitive method for the detection of mutagenic metabolites in urine. The urine is treated with the enzyme sulfatase and beta-glucuronidase to permit identification of substances that are made nonmutagenic by conjugation as glucuronides. The sample is then passed through an XAD-2 resin column and the absorbed organic molecules eluted with acetone. The sample is then split and evaporated to 1 ml and used for direct chemical analysis using HPLC. One drawback to the test is the inability to measure cumulative exposure, but multiple samples can be obtained and comparison to baseline (control) and exposure samples can reveal qualitative differences as a consequence of exposure to mutagens. [The Ames/Salmonella Microbiological Assay]: The Ames/Salmonella microbiological mutagen test is the most extensively used short-term bioassay, with over 2,600 chemicals having undergone testing by this method (Hollstein, et al., 1979). The method, thoroughly worked out and tested for 10 years, consists of taking the second split urine sample from the HPLC preparation, evaporating to dryness and dissolving in dimethylsulfoxide (DMSO). The sample is then applied directly to

Jan 1, 1981