Search Documents

By Gram Curtis

The apparatus described below for the handling of plates upon their delivery from the rolls, embodies features believed to be of interest to those contemplating the building of new plate-mills, and also to such owners of existing mills as may be considering the improvement of their works. The points to which attention is called are the small space required for the finishing-end of the mill, and consequently the very moderate size of the building for the amount of plates handled; the directness and ease of manipulation, and therefore the mall amount of labor required; the distribution of plates; the facilities and time allowed for their cooling. These, together with other features of detail and general arrangement scarcely less important, will become apparent when the descriptions and illustrations herewith given are understood. As these devices deal with the finishing of the plates only, they may be added to any plate-train when the floor-space and the building are large enough to permit their introduction; and it will be obvious that the features of this method, more or less modified, are applicable to any existing mill. Figs. 1 and 2 show a three-high 32-and 19- by 120-inch Lauth mill, with hydraulic lifting-tables, served by four heating-furnaces, with hydraulic cranes for charging and drawing. Upon leaving the rolls, the plate is allowed to rest with its forward edge projecting somewhat beyond the end of the catcher's table. Here it is seized by the automatic tongs, A, suspended from a buggy travelling in the overhead trough, B, and actuated by the hydraulic cylinder, C. These tongs are operated by a boy, who stands several feet from the heated plate, and controls the long light handle, D, shown in the plan, Fig. I. His duty is merely to advance the tongs by means of .the hydrulic cylinder, C, to raise or

Jan 1, 1892

ARTHUR BRICE deSAULLES In the death of, Major A. B. deSaulles at South Bethlehem, Pa., on Dec. 24, 1917, the Institute lost a valued and esteemed member, one of the last few of those who, in May, 1871, at Wilkes-Barre, attended the first meeting of the Institute, in response to a call that had been issued by R. P. Rothwell, Eckley B. Coxe, and Martin Coryell. Major deSaulles was born Jan. 8, 1840, at New Orleans, and was the son of Louis and Armide Longer deSaulles, each of French descent. As a boy he was privately tutored in the South, and then schooled in New England to enter the Rensselaer Polytechnic Institute, where he was graduated with honors in the class of '59. Following his graduation he studied in France and Germany for two years, returning to New Orleans in 1861 to enter the Confederate Army, in which he served with distinction- as an engineer throughout the Civil War, rising to the rank of Major and the command of his Corps. After the close of the war he pursued his studies abroad for another year, returning to New York in April, 1866, when be became engineer for the New York & Schuylkill Coal Company, and remained at its plant near Wilkes-Barre until October, 1871, when it was sold to the Philadelphia & Reading Coal and Iron Company.. He then returned to New York where for several years he was engaged in the practice of his profession. In 1869, he married Catharine M. Heckscher, daughter of Charles Heckscher of New York City. Mrs. deSaulles survives him. In 1876, Major deSaulles became superintendent of the Dunbar Furnace Company in Fayette County, Pa., with which company he remained until 1883. As a feature of the Pittsburgh meeting in May, 1879, Major and Mrs. deSaulles entertained the members of the Insti-

Jan 4, 1918

By R. E. Head

Under existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes. Surface Contamination The experience gained by microscopic study of numerous gold ores and tailings has shown that there are pronounced differences in the physical characteristics of the minerals composing them, more especially of the gold. Repeated studies of tailings from flotation and cyanidation of gold ores has established the fact that surface contaminations on gold particles are often directly responsible for high gold losses; comparison of gold particles isolated from flotation concentrates and the resulting tailings have showed that the clean gold has been recovered and the tarnished or contaminated gold invariably lost in the tailing. Obviously, it is not possible to make such a comparison of gold ores treated by cyanidation, as the clean gold has been taken into solution; but when the gold found in cyanide tailing has a tarnished or coated surface, one may infer, with a reasonable degree of certainty, that the clean gold has been extracted. This premise is supported by experimental evidence obtained by isolating particles of tarnished gold and exposing them to cyanide solution in small parting cups. In one such experiment, tarnished gold particles picked from a cyanide tailing showed but slight evidence 01 dissolving at the end of 27 days. In this test, a cyanide solution of 1.6 11). per ton was used and the leach solution was decanted arid renewed every

Jan 1, 1939

By B. B. Zavoico, J. G. H. Crump, P. P. Gregory

West Texas was the scene of greatly increased oil activity during 1937, producing 75,743,000 bb1.l in that year as compared with 61,901,-000 bb1.2 in 1936, an increase of 22.36 per cent. The annual total of wells completed increased from 15863 in 1936 to 28062 in 1937, an increase of 76.92 per cent. Of the total completions in 1937, 2464 were oil wells,2 11 gas wells2 and 331 dry holes.2 The marked increase in the number of oil wells completed in West Texas during 1937 had a substantial effect upon the daily average production per well, which decreased 20.84 per cent from December 1936, when a total of 5310 wells3 produced 5,236,467 bbl.3 for an average of 31.81 bbl. per well per day to December 1937, when 7571 wells2 with a total production of 5,910,257 bb1.2 averaged 25.18 bbl. per well per day. Drilling blocks and checkerboard acreage were being acquired following geophysical work in the northern end of the Permian Basin area, composed of Bailey, Cochran, Hockley, Yoakum and Terry Counties, presaging extension of active development northward. During 1937, at one time 30 geophysical crews were working in West Texas, and an average of 15 to 20 crews was active in this area throughout the year. Discoveries Wasson-Denver Field.—Wasson-Denver field in Gaines and Yoakum Counties was the outstanding field discovery of the year. Production is from porous limestone found at about 5000 ft., and an average well is good for from 300 to 500 bbl. of crude oil per day through 3/4-in. choke. The discovery well was drilled by A. G. Carter and others on the Wasson Ranch, Gaines County, and the field has since been extended into Yoakum County. At the year's end 21 wells had been completed, producing

Jan 1, 1938

By Paul B. Crawford, Bobby L. Landrum

An electrical model study has been mode to estimate the effect of horizontal fractures in thick reservoirs on pattern conductivity. For the patterns studied, it is shown that fracturing all the wells in the pattern in-creases the conductivity considerably more than frac-turing only single wells. For certain conditions one large fracture is more effective in increasing conductivity than several fractures of half the radius. Particularly in thick reservoirs and with large fractures, the center of the pay is found to be more responsive than other locations. For the seven-spot pattern fracturing the center well is more effective in increasing pattern con-ductivity than fracturing all outer wells with fractures of the same size. INTRODUCTION Although commercial fracturing has been used for some time very little quantitative information is known about the effects of fractures on reservoir behavior. The purpose of this work was to estimate the effect of horizontal fractures in thick reservoirs on the con-ductivity of various flooding and cycling patterns.2 Circular fractures originating at the wellbore and extending symmetrically into the pay were considered. ANALYSIS Electrical models were used in making this study. Horizontal fractures were simulated by copper sheets shaped like the fractures and of a proportional size; the wellbore was simulated by a copper wire. A dilute salt solution served as a conducting medium. A con-ductivity bridge was used to measure the conductivities of the various patterns studied. EFFECT OF HORIZONTAL FRACTURES ON CONDUCTIVITY Fig. 1 shows the effect on square and staggered line drive patterns of horizontal fractures located in the center of the pay. The model is shown schematically in the insert. The upper and lower groups of lines show the effect on conductivity when all wells are fractured, and when only one well is fractured, respectively. In general, pattern conductivities are substantially improved by fracturing all wells. Fig. 2 shows the effect of multiple horizontal frac-tures on the conductivity of a line-drive pattern. At

Jan 1, 1958

By D. Harrington

EFFICIENT ventilation of metal mines consists in having such complete control of air currents that. there is always supplied at places where men work sufficient moving air to allow working at maximum capacity without injury to health; and in case of underground fire or of surface fire in the vicinity of mine openings, underground air currents may be quickly reversed if desired, or air may be sent into or excluded from any region and fire fumes confined to only part of the mine workings, instead of penetrating practically the entire mine. Health and safety of workers in mines as well as proper safeguarding and operating efficiency of mining properties are so intimately associated with proper ventilation of mines (both coal and metal) that they are inseparable, yet mine ventilation is only too frequently neglected, especially in metal mines. The metalliferous operator, generally not confronted with inflammable gas or explosive dust which so frequently force ventilation of coal mines, usually disregards air supply altogether except such as may be obtained from compressed air; and generally, even when attention is given to metal-mine ventilation, the air currents rarely are found where they are needed, namely, the working places, especially the working faces. After several years' study of miners' consumption, the writer is. convinced that long continued breathing of air impregnated with large quantities of any kind of finely divided dust, such as is found in a large number of the working places of our mines, will ultimately produce some respiratory disease, whether it be asthma, bronchitis, or phthisis; and the progress of these diseases is hastened. if there are also present high temperatures, high humidities, or harmful gases or if there is present (and allowed to remain to be breathed) large quantities of the finely divided dust when air temperatures are low, hence favorable to maximum performance of work with accompanied maximum breathing into the respiratory passages of the harmful material. It is generally accepted

Jan 2, 1922

By A. H. Bell

The general principles of the gas-lift will not be described in this paper. Only specific details that have not been fully discussed in previous papers, or results that do not fully coincide with conditions previously described, will be dealt with. The principal points to be emphasized and for which supporting data are furnished are as follows: 1. Gas-lift installations usually have comparatively high efficiencies as compared with standard pumping equipment, when reduced to a basis of barrels produced per horsepower installed. 2. Advantages of high-pressure plants from the standpoint of operating efficiency and for the application of the gas-lift early in the life of flowing wells. 3. Evidence of increased ultimate yield through conservation of gas by the gas-lift. 4. Possibility of development of new equipment to increase efficiency of the gas-lift. 5. Indications of the advantages of repressuring as a means of stabilizing gas-lift wells and as a means of increasing ultimate yields. TyPes of Installation The gas-lift installations of the more important companies in California have been of the central-plant type wherever field conditions would permit. This has resulted in greater flexibility and lower installation costs per well than could be obtained with individual well units. In general discussions of the gas-lift method of production, the installation costs are frequently referred to as being too high for economical operation. If the field conditions are carefully analyzed and the plant designed with the idea of obtaining high operating efficiencies, the installation cost per well can be lowered sufficiently to compare favorably with individual well-pumping units, when the operating advantages are considered. Much greater production per horsepower can be obtained with the gas-lift than is possible with pumping equipment. Table 1 shows the unit sizes and costs of gas-lift installations of three companies in the Los Angeles basin. The cost of walking beams, rods,

Jan 1, 1928

By I. R. Kramer

A study was made of the effect of surface-active agents an copper, gold, and zinc single crystals as well as polycrystalline aluminum. The study on coppw showed that the maximum effect of the surface -active agent occurred at the same concentration of the solution as that at which the rate of solution of the copper soap was the greatest. Surface -active agents did not affect the creep behavior of gold or freshly polished zinc specimens. The creel-, rate of zinc specimens in a solution containing a surface-active agent zoas always lower than that of freshly polished specimens. In previous papers1'2 it was reported that the surface played an important role in the plastic deformation of metals. By removing the surface layers of a crystal of aluminum by electrolytic polishing dur- ing tensile deformation, it was found that the slopes of Stages I, 11, and In were decreased and the extent of Stages I and I1 were increased when the rate of metal removal was increased. The results of the investigation of surface-active agents showed that changes in the slopes and extents of Stages I and II occurred when single crystals of aluminum were deformed in tension in a bath containing solutions of paraffin oil and stearic acid. The amount of change was a function of the concentration of stearic acid and the maximum effect occurred at a concentration of 0.002 mole per liter. These results were interpreted2 in terms of the rate of solution of metal soaps which form as a result of the chemical reaction between the surface-active agent and the metal. According to this interpretation, the "weakening" effect is controlled by the rate of solution of the soaps which depends upon the concentration of surface-active agents. At low concentrations, the number of metal soap molecules formed is low; at high concentrations, the rate of solubility is low, because of the high degree of saturation.

Jan 1, 1963

By T. Olrog

Dissemination of technical data on developments in rock-blasting techniques in Sweden initially takes place as personal contacts and contacts between companies. In addition to these informal contacts, contacts occur in Sweden in a somewhat more organized form. There exists an informal working group--the Rock Blasting Committee--which consists of a number of personal representatives from various companies that perform rock blasting on a large scale and from firms manufacturing the equipment that is used. This means that people from both mining and construction companies get together, plus the manufacturers of explosives, drill steel, drilling machines, and loading equipment. This working group has, so far, succeeded very well in ignoring the purely commercial interests of the companies concerned. Cooperation in this form was started in the 1940's when the tungsten-carbide drill steel was invented-the group originally concentrated entirely on the development of that product. Their activities have been broadened since that time and now a meeting is held every year, at which practical experiences are reported. Only in the past five years have subjects relating to blasting procedures to avoid rock damage been treated at such meetings. This, of course, does not mean that such techniques had been neglected previously. It does, however, reflect the fact that practice in this field is still under development. Why do we try to be careful about the rock surfaces? Obviously, it is a question of economic evaluation. An even rock surface provides, in certain cases, the conditions for more favorable maintainance costs later on, greater strength, and a diminished risk of slides. The economic connections in this field, however, are neither simple or clear. A well-controlled blasted rock surface limits the need for concrete when you later build the concrete constructions. In this respect, the connections are all the more clear. In certain situations, such as tunnels for hydroeletric power plants, a good rock surface that is not lined is hydraulically more favorable than a more coarsely blasted surface. This permits a gain in the height of fall, but the

Jan 1, 1970

By John M. Bostwick

Bitumen is a general term for a group of materials composed of mixtures of hydrocarbons that are fusible and soluble in carbon disulfide. Included in the group are petroleum, asphalts, asphaltites, and mineral waxes. Asphalt is a dark-colored, cementitious solid or semisolid, which generally softens on heating and resumes a more viscous or solid state when cooled (personal communication). It is found in native form in fissures and pore spaces in rocks and as lakes. It is also obtained from the residues produced in petroleum refining. Asphaltites are black, naturally occurring solid bitumens. They are generally shiny and break with a conchoidal fracture. Common asphaltites are gilsonite (uintahite), grahamite, and glance pitch. Mineral waxes are solid or semisolid, relatively nonvolatile bitumens of various colors, having an unctuous feel and waxy luster. Of the native waxes, ozokerite is the best known. Montan wax is also classed as a natural wax, although it never occurs in the pure state and must be extracted from lignite or cannel coal (Ladoo, 1920). Mineral waxes may also be obtained by pyroprocessing of petroleum, lignite, and peat. Pyrobitumens are dark-colored, solid hydro- carbons that are infusible and relatively insoluble in carbon disulfide. They are so-called because they will yield liquid and gaseous hydrocarbons only when heated. Asphaltic pyrobitumens are defined as "substantially free of oxygenated bodies" and include wurtzilite (elaterite), albertite, and impsonite (Thrush, 1968). Nonasphaltic pyrobitumens contain oxygenated bodies; examples are coal and peat. The nonasphaltic type will not be discussed further. Petroleum Asphalts Asphalts refined from crude petroleum have almost completely replaced the native types. Refineries can produce asphalts in every desirable grade more economically and in greater quantity than the native types and with a variety of properties that meet the requirements of the various manufacturers using them. For all practical purposes, it is estimated that more than 95% of the asphalts consumed in the United States are refined from crude petroleum (private communication).

Jan 1, 1975

By John Primrose

Tube stills having demonstrated their usefulness for refining operations, the later developments in their design have been in the direction of improved thermal efficiency. The earlier designs operated with low furnace temperatures and large volumes of furnace gas because the fuel was burned with much excess air. It was quite possible to provide sufficient heating surface to lower the temperature of the flue gas to within 150" of the temperature of the inlet oil, or when inlet-oil tempera-tures were high to have the flue gas escape at 300" or 350" F. by using the heat remaining in the flue gas from the still to preheat the air supplied for combustion. But even so, the thermal efficiency was low because of the large quantity of air used for combustion. The large quantity of excess air was required to burn the fuel in the furnace at a temperature low enough to prevent overheating the furnace walls and overheating of the oil. Supplying heat to the tubes of the heating surface at a rate beyond the capabilities of the oil to absorb, except with a considerable difference between the temperature of the inside of the tube and oil passing through, would result in overheating the tubes and the oil in contact with them. For these reasons it was very necessary in the older types of tube stills to burn the fuel with large quantities of excess air, resulting in low thermal efficiency despite the low flue-gas temperature. Neglecting loss by radiation, the thermal efficiency could be improved only by burning the fuel with less excess air, but it was necessary to accomplish this without upsetting the furnace temperature conditions existing when large quantities of excess air were used. There are several methods of bringing this about, such as controlling the furnace temperature by returning a proportion of the flue gas to the furnace, or by exposing direct to the fire a heat-absorbing surface so located and proportioned that sufficient heat will be absorbed by radiation to prevent excessive furnace temperatures.

Jan 1, 1928

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

Data or input files are used to describe the mine's ventilation system and physical characteristics necessary for ventilation calculations as well as the physical or mechanical disturbance to be modeled and simulated Data files are organized into lines of categories or groups of information Each line contains multiple sets of information or data items Data lines are read by the program, and the data items provide information to the program variables The data file is in American Standard Code for Informa¬tion Interchange (ASCII) format, sometimes called a DOS text format Creation or modification of a data file is accomplished with text editor software Most word pro¬cessors are also capable of making the required ASCII type files A sample data file and its associated output are included in appendix B. When selecting software for editing the data files, the user should be aware that the software will also be used for viewing the output of the simulation The output file can be quite large (several megabytes), if a lengthy simulation is performed The output can be sent to a printer for a hardcopy fisting, however, the user should also be aware that most printers currently used with PC's print at rates of 100 to 300 characters per second and large output files may take several hours to print Viewing the output with a text editor can save much time and paper DATA FILE MANAGEMENT The data files describing the event and mine to be simulated can reside either on a floppy disk or in a directory on the hard disk drive When the program starts, the user is prompted for the data file location and name The user response is in the form of a standard DOS path and file name For example, if the data file is on a floppy disk located in drive B and the disk has a directory MYMINE with the data file MYDATA DAT in that directory, then, at the prompt

Jan 1, 1990

By Zhang Libo, Wang Xin, Peng Jin-hui, Ju Shaohua, Guo Sheng-hui, Xu Lei, Huang Meng-yang

"China is lacking high grade titanium ores. This work intends to leach impurities such as Fe, Ca and Mg from a low grade titanium ore, to increase the grade. The original material contained 65% TiO2 , 16.12% Fe, 9.4% CaO + MgO, 4.2% SiO2, 1.25% A12O3, and the particle size is between 0.053-0.045mm. Microwave energy was used to enhance the leaching effect. The results showed that when normal heating was used to leach the mineral, the extraction of impurities Fe, Ca and Mg was very low. However, when microwave energy is introduced, the extraction of Fe, Ca and Mg increased dramatically. The optimized conditions are: relative power 5W/g, the ratio of concentrate to HC1 isl5%, leaching at 160°C for 20 min with a ratio of liquid to solid 12:1 mL/g. The material obtained under these conditions contains 92.73% TiO2, 0.207% Ca + Mg, 0.8% Fe, with 94.6% Ti recovery. The poduct meets with the quality for boiling chlorine.IntroductionThe resources of titanium are very abundant, and are distributed all over the world. There are almost 140 minerals containing TiO2 with a content of more than 1%. However, there are only several minerals which can be used for producing sponge titanium. They are mainly rutile and ilmenite. The grade of nature rutile concentrates is higher than 95% TiO2, and it is a high quality raw material. But the resources of nature rutile are relatively low; after mining for many years, its resources are exhausting gradually. Although ilmenite reserves are great, ilmenite cannot be used as a raw material because of its low content of TiO2, only 45-70%; also it has a high impurity content of Ca, Mg and Fe. In these years, there is a tendency for titanium industry to use high grade concentrate."

Jan 1, 2012

By Arthur Knapp

The petroleum industry is confronted with the problem of conservalion. This is not a simple problem in view of a wide difference of opinion among authorities as to whether conservation is necessary and the specific direction that it should take. Many writers accuse the petroleum industry of wasting the natural resources of the country. Others link the consuming public with the industry in this waste. Let us define our terms; agree, if possible, on where and when waste occurs in connection with either the recovery or use of petroleum and select such plans for conservation as appear most practical. A plan for conserv3tion which appears to be logical today may not meet the problem tomorrow. The conservation of petroleum is closely linked with the advancement of marly arts and sciences and as these advance, the plan of conservation has to change. The need for conservation does not necessarily rest upon the elimination of waste. There is not necessarily a fixed connection between waste and conservation. Conservation may be necessary or desirable although there is no waste. Definitions Waste: Useless or unnecessary expenditure. Conservation: The preservation of the natural resources for economical use. Both definitions contain adjectives the interpretation of which is extremely difficult. It is the determination of what expenditures are "unnecessary" or what uses are "economical" that will require study and agreement. If one lets his automobile engine run in cold weather in order to keep it hot, it is difficult to measure that necessity. If an automobile is driven two blocks, when the driver is physically capable of walking, what is the measure of necessity. This question is in the realm of one of the oldest of sociological problems, "What is a luxury?"—a problem which has not been solved. The history of society indicates that the measure of a man's wealth has been the measure of necessity. What he can afford to buy without stinting himself in some other direction, is not a luxury to him and, if it fulfills his desires, may be considered his necessity.

Jan 1, 1927

By R. E. Head

Under existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes. Surface Contamination The experience gained by microscopic study of numerous gold ores and tailings has shown that there are pronounced differences in the physical characteristics of the minerals composing them, more especially of the gold. Repeated studies of tailings from flotation and cyanidation of gold ores has established the fact that surface contaminations on gold particles are often directly responsible for high gold losses; comparison of gold particles isolated from flotation concentrates and the resulting tailings have showed that the clean gold has been recovered and the tarnished or contaminated gold invariably lost in the tailing. Obviously, it is not possible to make such a comparison of gold ores treated by cyanidation, as the clean gold has been taken into solution; but when the gold found in cyanide tailing has a tarnished or coated surface, one may infer, with a reasonable degree of certainty, that the clean gold has been extracted. This premise is supported by experimental evidence obtained by isolating particles of tarnished gold and exposing them to cyanide solution in small parting cups. In one such experiment, tarnished gold particles picked from a cyanide tailing showed but slight evidence 01 dissolving at the end of 27 days. In this test, a cyanide solution of 1.6 11). per ton was used and the leach solution was decanted arid renewed every

Jan 1, 1939

By C. A. Heberlein

The present war in Europe seems to have stimulated the demand for quicksilver. In July last, the price ranged around $35 per flask of 75 Ib., while to-day it seems to fluctuate between $47.50 and $50. The use of quicksilver in the form of fulminate, containing 70 per cent., and as corrosive sublimate, containing 73.8 per cent., must be extensive and a further market advance may be expected. With such an advance, some revival in quicksilver mining may be looked for, particularly in California, where many abandoned properties exist. What can be done with low-grade quicksilver ores under favorable conditions, particularly with low mining cost, may be seen from the following description of the Oceanic mine, near San Luis Obispo, Cal. Its operations date back to 1876, when rich sand ores were discovered. In three years 7,400 flasks of quicksilver were produced, but since then the deposit has been worked only sporadically . Until two years ago various attempts had been made by the Oceanic Quicksilver Co. to mine the more refractory "mud rock," which was encountered lying beyond the " sand rock." Mud and sand rock in varying quantities were treated together, with poor results, but operations were successful with sand rock of fair percentage. About two years ago, when all the sand rock had been exhausted, Murray Innes purchased the Oceanic mine. He found large quantities of low-grade mud rock, varying from 6 to 8 Ib. of quicksilver per ton, which at the prevailing low price of quicksilver demanded very cheap mining costs, in conjunction with high but cheap metallurgical extraction. At that time the extraction of quicksilver from mud rock ranged between 40 and 50 per cent., as far as I am able to learn. Mining The low cost of mining was the principal consideration, since, with mercury at 50c. per pound, the total gross value of the ore did not exceed

Jan 1, 1915

By Samuel M. Cassidy

The exact date of man's first use of coal is lost in antiquity. The discovery that certain black rock would burn was undoubtedly accidental and probably occurred independently and many times in the world over thousands of years. It is quite likely that these independent discoveries were made when primitive man chanced to build camp fires on exposed ledges of a black rock, then was amazed when it caught fire. The Chinese recorded the use of coal 1100 yearn before the Christian Era and from the Bible we learn that King Solomon was familiar with coal in what is now Syria. In Wales, there is evidence that the Bronze Age people used coal for funeral pyres, and it is known that the Romans used this fuel. There are other ancient references. So the knowledge that coal would burn, and even some uses of that knowledge, go back thousands of years. However, practical and consistent use of coal seems to date to England in the Middle Ages. COAL IN AMERICA In the Americas, there is evidence here and there of occasional use by the Indians. However, the first recorded discovery of coal, in what is now the US, was by French explorers, who reported an outcrop exposure on the Illinois River in 1679. Following this, other discoveries were made by French and British explorers, but the first recorded actual usage was in Virginia in 1702, where a French settler was granted permission to use coal for his forge. Earliest recorded commercial mining was in 1750, from the James River coaEeld near Richmond, VA, a deposit now abandoned. Besides local consumption from this field, shipments were made to Philadelphia, New Pork, and Boston. During the Revolution this coal was of impor- tance in the manufacture of shot and shell; so important, in fact, that the British sent an expedition in 1781 to destroy the iron works and

Jan 1, 1981

By Frank E. Hall

The needs of the World War showed the necessity of a metal stronger than cast iron which would supplement the supply of steel. SO patriotic metallurgists were spurred to new efforts to improve the status of that half-breed of the metal world that had been, more or less erroneously, christened semisteel. As a result, it was developed that for certain purposes semisteel was superior to steel in the manufacture of shells. Steel, because of its greater strength and toughness, is able to carry a greater charge of explosive, weight for weight; consequently, a steel shell can be expected to cause greater destruction when used against fortifications or other inanimate objects, while semisteel, because of its comparative brittleness and its resulting greater fragmentation, is capable of inflicting more serious loss of life when used against opposing forces of men. Therefore, each has its proper place in the economy of war. For the present purpose, steel may be defined as a comparatively pure iron whose physical nature is modified by small amounts of carbon, silicon, sulfur, phosphorus, manganese, and possibly other rarer elements; while cast iron generally is limited to approximately 93 per cent. of iron, the remainder consisting of larger percentages of carbon, silicon, sulfur, phosphorus, and manganese. Semisteel may be defined as cast iron in which the carbon and silicon have been reduced to as low a point as is consistent with maintaining the nature of gray iron, and in which the remaining elements are adjusted so as to give the greatest strength. The fact that the addition of steel scrap, in varying percentages, is the means used to reduce the carbon, together with the fact that a considerable increase in strength results, is probably the explanation of the origin of the name semisteel. That ordinary grades of steel show from three to four times the tensile strength of cast iron is due to the fact that the crystals, or grains, of cast iron are interspersed with flakes of

Jan 1, 1922

By D. Harrington

Efficient ventilation of metal mines consists in having such complete control of air currents that there is always supplied at placcs where men work sufficient moving air to allow working at maximum capacity without injury to health; and in case of underground fire or of surface fire in the vicinity of mine openings, underground air currents may be quickly reversed if desired, or air may be sent into or excluded from any region and fire fumes confined to only part of the mine workings, instead of penetrating practically the entire mine. Health and safety of workers in mines as well as proper safeguarding and operating efficiency of mining properties are so intimately associated with proper ventilation of mines (both coal and metal) that they are inseparable, yet ventilation is only too frequently neglected, especial1y in metal mines. The metalliferous operator, generally not confronted with inflammable gas or explosive dust which so frequently force ventilation of coal mines, usually disregards air supply altogether except such as may be obtained from compressed air; and generally, even when attention is given to metal-mine ventilation, the air currents rarely are found where they are needed, namely, the working places, especially the working faces. After several years' study of miners' consumption, the writer is convinced that long continued breathing of air impregnated with large quantities of any kind of finely divided dust, such as is found in a large number of the working places of our mines, will ultimately produce some respiratory disease, whether it be asthma, bronchitis, or phthisis; and the progress of these diseases is hastened if there are also present high temperatures, high humidities, or harmful gases or if there is present (and allowed to remain to be breathed) large quantities of the finely divided dust when air temperatures are low, hence favorable to maximum performance of work with accompanied maximum breathing into the respiratory passages of the harmful material. It is generally accepted

Jan 1, 1923

By P. B. Elkin, K. C. Ten Brink, Allen D. Garrison

It is the purpose of this article to present the results of an investigation of certain clay and shale suspensions having viscosities that are materially influenced by fluid motion, and to discuss the bearing of these results upon the choice of policy in the control of drilling fluids. A previous article described the design and the characteristics of an instrument adapted to measure the viscosity of plastic suspensions during continuous uniform motion and at a variety of speeds.' It has long been recognized that the viscosity of a clay suspension depends on the past history of the fluid motion. Since an abundance of literature is available on this phenomenon,2 it is not necessary to describe it in more than general terms. It is usually observed that rapid motion reduces the viscosity of a clay suspension, and that some time is required for the viscosity to fall to its equilibrium value after the steady motion is started. On reducing the speed of motion to some lower value, the viscosity again rises, but it also requires some time to attain a steady viscosity value at the slower rate of motion. Thus clay suspensions are usually observed to be increasing in viscosity as time passes when the measurement has been immediately preceded by fluid motion that was more rapid than that employed in the measurement. And it is usually observed that the viscosity falls as time passes when the measurement has been preceded by more quiescent conditions. Reed,3 and Broughton and Hand4 have reported a condition of observation of clay suspensions in which the viscosity was observed to fall during the first few moments of steady motion, and rise thereafter. The characteristics of the new instrument are particularly well adapted to studies of this kind. With it we have been able to observe all of the phenomena described above, and it is important to understand their nature because they all occur at some time during normal drill-

Jan 1, 1940