Search Documents

By W. A. Alexander

Introduction In the course of a programme of research on beryllium in progress in these laboratories, knowledge of the recrystallization temperature became necessary. As the information is not available in the literature, the determination of this temperature for metallic beryllium was undertaken. By the reduction of grain size through working and recrystallization and the probable simultaneous induction of preferred orientation, it was hoped to improve the working properties of beryllium at lower temperatures. The recrystallization temperature is usually determined by observing the lowest temperature of annealing at which new crystals are formed in severely cold-worked metal or alloys. This temperature is profoundly influenced by the following factors: the purity of the metal, in the case of an element, or the composition of the alloy; the degree of straining or working; the temperature of straining; the original grain size; and the time held at the annealing temperature. The observed temperature is lowered by higher purity, more severe straining, lower temperature of working, smaller original grain size, and longer time of annealing. Beryllium presents special difficulties in that the percent elongation in tension is effectively zero, so that ordinary squeezing or rolling was not possible. A possible means of straining was suggested by the fact that indentation hardness tests could be made. It was known from earlier work that the metal could be worked at elevated temperatures, so that working at the lowest feasible temperature and quenching might also be a means of producing strain. The purity of the metal is also a point of some uncertainty in the case of beryllium. Losano has prepared 99.96% Be which appears to be the best reported. Distilled metal used in the present work approached this purity. However, by analogy with other metals, residual impurities may have a pronounced effect on the recrystallization. Further purification of beryllium would evidently entail considerable difficulties due to the highly reactive nature of the metal, and was not attempted.

Jan 1, 1947

By G. E. S. Valadao

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake pore microstructure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 µm, length of 500 µm and height of 4000 µm. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: I) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method, 2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4) some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By Arthur L. Murray

"Oil-shale camps are peculiarly favored, in that before they are establishes it can be ascertained with a degree of certainty, that the life of the project is not limited. Unlike camps at metal mines, where the metal content of a given area is frequently an unknown quantity until after years of development, oil-shale camps should, from the outset, be planned and. built as permanent types of camps. Where this procedure is followed camps will be established which better serve the needs of the industry and the cost of their general care and upkeep will be less.Selection of camp or townsite.The site of the camp or town' whether on company property or not, should be selected with care. It should be separate if possible from the location of the plants of the company so as to be free from noise and fumes and so as to provide a change of environment for employees in going from their work to their homes.The principal features governing the site to be selected are as follows:Drainage. The general contour of the surrounding country should be such that drainage is away from the site. The camp or town should, if practical, be situated on higher ground than that in its immediate vicinity.Soil. The nature of the soil on which the camp or town is located may bear a decided relation to health. A porous, well underdrained top soil of at least four feet in depth insures dryness and facilities the placing of foundations and the laying of water mains and sewer pipes. Such a soil also is an advantage in growing trees, shrubs and grass plots, which are a decided adjunct to making the community attractive.Enviroment. The contiguous territory should afford no unwholesome sur¬roundings such as swamps Or accumulations of stagnant water.General Considerations. The water supply to be provided and the method of disposal of wastes influence to a certain extent the location of the camp or town-site. The means of supplying water, whether by gravity or by pupping, and the disposal of sewage, whether by outfall, system, sewage disposal system through septic tanks, broad irrigation or filter beds, or cesspools will govern the location of the site topographically in relation to source of water and point of disposal of sewage.* This article was prepared as part of the paper ""Use and Supply of Water for the Oil-Shale Industry"" by J. J. Jakowsky, to be published by the Department of Metallurgical Research, University of Utah, in cooperation with the United States Bureau of Mines."

Jul 1, 1921

By A. Rai

"This paper provides an overview of the current use of auxiliary ventilation product and the challenges with limited air quantity in dead-end entry or working face. The PVC low frictional factor, low physical constraint and minimum leakage ventilation duct was development with ""made in US and used in US"". The PVC duct development covering operational and total cost of ownership with on-going success will be presented. This paper will discuss mine sites using new PVC vent duct underground and the results from operational and technical side making a difference. INTRODUCTION The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone’s, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods [3].Mining Method; Underhand cut and fill : The mine uses underhand cut and fill method which has 12’x12’ top cuts and several different size undercuts. The ore body is accessed off of a secondary development heading, utilizing a heading with a cross section of 14W x 14H or 15W x 16H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the type of drilling machine being used. An example of a typical topcut and associated undercut layout is shown in Figure 2. SECONDARY / AUXILIARY VENTILATION IN UNUNDERGROUND METAL MINES The auxiliary ventilation system provides the required air volumes at the face of dead-end developments and production workings, which in many cases may be considered as the primary method of assuring that the air quantity and quality standards in these working areas are satisfied. The Auxiliary fans and ducting systems are usually the primary means of delivering the required air volumes to the face of dead-end developments and production workings. Both centrifugal and axial-flow fans are used in underground auxiliary ventilation systems, usually electric powered. The internally direct driven axial-flow fans tend to be more popular because of their compactness and adaptability to staging. The most commonly used materials for ridged tubing are coated steel, alloyed steel, fiberglass and resin. Flexible (collapsible) ventilation tubing is also used and is usually made from neoprene-coated or nylon material. To add stiffness and reduce collapsibility these fabric ducts can be formed over a steel spring frame. A very important factor in the design of an auxiliary ventilation system is to minimize leakage and reduce the frictional pressure losses along the auxiliary ducting systems by minimizing their friction factors (K)."

Jan 1, 2015

By R. S. Farinato

Thionocarbamate flotation reagents have enjoyed a niche position in the recovery of copper sulfides and activated sphalerites since their introduction in the mid 1950's (Harris, 1954). Thionocarbamates containing an allyl group (-CH2- CH=CH2), introduced recently Lewellyn, 1985; Nagaraj, 1988; Avotins, 1991), are used commercially as collectors for copper sulfides and activated sphalerite. Laboratory flotation tests and plant usage have demonstrated that allyl-containing thionocarbamate collectors exhibit certain unique properties that distinguish them from the corresponding dialkyl thionocarbamates. Spectroscopic (FTIR, XPS) and wettability studies of N-allyl iso-butyl thionocarbamate (AIBTC) and its saturated analog N-propyl iso-butyl thionocarbamate (NPIBTC) adsorbed on copper at pH 9 were performed in order to investigate whether there were any fundamental reasons for these differences. Flotation tests were carried out on chalcocite, copper ore and an activated sphalerite.

Jan 1, 1993

By G. Frithum

In the present paper a new and highly economic route for Fe-separation from HCl leaching processes in hydrometallurgical applications is described. In most ore leaching processes, Fe is involved and needs to be separated; HCl has become an interesting leaching agent, because it can be recycled. Usually a mix of Fe2+ and Fe3+ is obtained which can be hydrolyzed directly (in case only Fe3+) or roasted via pyrohydrolysis (in case of Fe2+) to ferric oxide. Economic oxidation of Fe2+ to Fe3+ is described, and potential technologies for regeneration of HCl with separation of Fe are shown and compared.

Jan 1, 2014

By N DavT

Pyritic tailings from the Quirke mine waste management area in Elliot Lake, Ontario were subjected to long-term column leaching experiments in two PVC columns measuring 122 cm in height and 15.2 cm in diameter. At the end of the leaching experiments, the columns were taken apart and sampled at 5 cm intervals for quantitative mineralogical and geochemical characterisation. Each column is represented by a total of ten samples. Polished sections, prepared from the samples, were studied by optical microscopy, scanning electron microscopy, electron microprobe and X-ray diffraction techniques. Mineral quantities were determined based on linear mixing models of whole rock and mineral compositions. Pyrite particle sizes were measured by image analysis interfaced to an electron microprobe. The tailings are coarse-grained (ie 96 per cent passing 75 ¦m) and composed of quartz, K-feldspar, muscovite and pyrite. Pyrite is homogenous and occurs as liberated particles displaying angular to subangular boundaries with strong dissolution features at the end of the leaching experiments. Based on up to 3518 particles measured in a sample, pyrite particle sizes range from 1.7 to 78.6 ¦m. Pyrite concentrations vary from 0.1 to 7.8 wt per cent, depending upon their location from the top of the columns. These correspond to pyrite losses of up to 99 per cent from their original level of 7.2 wt per cent in the upper half of the columns. Pyrite oxidation rates in terms of moles of pyrite oxidised per mole of pyrite per square metre per second were calculated from the effluent data and the measured pyrite particle sizes. The rates vary from 1.71+10-12 to 5.78+10-10 mole+m-2+s-1 within the 1.5 to 3.5 pH range for 10 ¦m particles. These results are comparable with the published oxidation rates at pH 2 where the dissolved oxygen is the only oxidant.

Jan 1, 2003

By E. Lee

The behavior of As bioleaching using Acidithiobacillus thiooxidans (A. thiooxidans) in mine tailings containing highly concentrated As contents (i.e., As=33877 mg/kg) was systematically evaluated according to the changes in temperature (25?40°C, pulp density=0.5%, pH=1.8), pulp density (0.5?4%, temp=30°C, pH=1.8), and initial pH(1.8?2.2, temp=30°C, pulp density=0.5%). The changes in temperature and pulp density affected the As leaching behavior more than the change in initial pH did. Based on the pH and oxidation-reduction potential (ORP) results, the As leaching was attributed to solution acidification. In particular, As leaching was accelerated with increasing sulfate production in the reacting solution. After bioleaching, surface of tailings examined that many pores which dissolved As were formed by a chemical reaction due to bacteria. The As bioleaching efficiency by A. thiooxidans was enhanced by the oxidation of both the added elemental sulfur and the sulfur compounds in the mine tailings. The As bioleaching efficiency was maximized at 50.5% under conditions of an initial pH of 2.2, reaction temperature of 30°C, and pulp density of 0.5%.

Feb 23, 2014

By P. Radziszewski

Industrial practice in mineral processing shows that an important problem in understanding and monitoring in-mill parameters is due to the lack of fundamental knowledge and appropriate sensors. With the development and growing use of DEM charge motion simulators for mill optimisation and design, it is possible to describe the fundamentals of grinding mill behaviour, in improving the understanding of internal grinding mill dynamics and in developing solutions to industrial practice. The main challenge to bringing this DEM technology to the mill operator however was the need for substantial computing power and time. However, what about a simplified DEM charge motion model running in real-time? What about the use of sensor technologies to correct any possible drift in simulator prediction? Could such a technological system be used to predict mill performance and eventually be used for mill control and optimisation? Some of these questions are answered with the development of an "on-line" DEM charge motion simulator package (SAGTools?) along with that of a number of sensor technologies (liner wear, acoustic, instrumented ball) that can contribute to simulator precision. With the objective of bringing this modelling and sensor technology into the concentrator control room to assist operators, this paper aims to describe the main elements of this emerging and developing technology and discuss how it can lead to online mill performance prediction and eventual control.

Jan 1, 2007

By J. B. Malcolm

The discovery of tungsten-bearing quartz outcroppings in Vance County, N. C., by the Hamme brothers in 1942, made international news in the mining industry and was, in fact, one of the major ore discoveries made in the U.S. during the last 25 years. Operations began at the Hamme mine in 1942, but after 16 years of successful operation, the mine was closed down in 1958 under adverse market conditions. By that time, it had produced nearly 20 million lbs of metallic tungsten. Because of the square-set timber mining method then in use, mine operating expenses were high, actually representing 78% of the total operating expenses at the property. In timber work alone, 160 men were employed. Approximately 500,000 bd ft of timber were placed monthly at a direct supply cost of $1.00 per ton of ore mined. Late in 1959, following a slightly improved position in the tungsten market, company management decided that, by changing the mining method, the operation could be economically feasible. The major premise in this decision was that a reduction of from 25 to 30% of the mining costs could be achieved by the conversion of the mining method from square-sets to horizontal cut and fill. Reopening of the mine began in February 1960, Full production has now been reached and overall mine productivity has been doubled.

Jan 1, 1962

By S. Owada

A national project of ?Establishing ?Green-Hydrogen (G-H)? Society in Honjo-Waseda Area? is now being developed by Waseda University together with four other universities and ten companies. The project involves three tasks of technological development of, (1)?G-H? production, (2)?G-H? refining, transportation and storage, and (3)?G-H? utilization. This paper focuses the first task of ?G-H? production from aluminium dross. We developed the physical treatment process by combining selective grinding with vibrating rod mill and electrostatic separation, in order to produce two kinds of materials, one is metal aluminium concentrate to recover it and the other is raw material to produce ?G-H? and aluminium hydroxide which can be generated by the treatment with sodium hydroxide aqueous solution. Here, we described the concentration mechanism of metal aluminium in the selective grinding and electrostatic separation and proposed a separation flowchart for optimizing the ?G-H? system in Honjo-Waseda area.

Jan 1, 2014

By Z. C. Shen

As core part of flotation column, aerator has been always priority research. A new type of porous aerator made of stainless sintered microcellular material is designed , which diameter is between 20µm to 40µm. High bubble surface area flux is obtained at low air pressure 20kPa by this type of aerator in water. In order to extend its applied range ,experiments were carried out in alkali slurry (pH=12) , resulting with porous aerator clogged after working 20 days . Sampling the cross-section of aerator detected by microscope and X-ray diffraction ,the reason clogging was found. Then plugging aerator was reactivated after putting it in acidic liquor treated by ultrasonic for about ten minutes. On-line aerator maintenance can be done in no down time , and it can be repetitive-used after recovered ,so reduced capital costs.

Jan 1, 2014

By T. W. Camm

The Bureau of Mines conducts studies of the economic impacts of regulations on federal lands. These studies are part of the Bureau Potential Supply Analysis (PSA) program. To meet the needs of these studies, a methodology was developed to estimate operating and capital costs for a mineral deposit given its tonnage, grade, and depth. The format for the cost models in this study was developed at the Bureau's Western Field Operations Center (WFOC), Spokane, W. A., for studies of known and undiscovered resources on Federal lands. These cost models are described in a Bureau publication by Camm (1991).

Jan 1, 1993

By David Rees

Tomago Aluminium, a 400,OO tonnes per annum primary aluminium smelter in Australia, has installed Ozone for biological control of its process water. The system was designed in Australia by Ionics Watertec Engineering, whilst ANCO Australia monitors the water quality and provides technical support for the project. The motivation was initially to reduce operating costs, however investigations indicated that there were substantial environmental benefits to be achieved by the elimination of a part, or all of, the chemicals being used to control the system. Also the existing chemicals appeared to be losing their ability to control biological growth in the system, in particular, the legionella bacteria. Ozone water treatment commenced in January 1998 and after a short transition period has operated without chemical addition since. There appears to be no doubt that the biological control is effective, the clarity and purity of the water has improved and initial testing indicates that the corrosion control rate is acceptable, although some chemical corrosion control may be introduced after further testing around the total circuit to guarantee protection

Jan 1, 1999

By Ö. Y. Gulsoy, L. Ergün, I. B. Celik

"In this study, the studies to develop a flowsheet for a low grade chromite ore are presented. The existing concentrator had to be suspended due to the decreasing metal prices. The study commenced with mineralogy and liberation profile of the chromite. The valuable mineral is chromite and the major gangue mineral is forsterite together with small amount of brucite and calcite. Heavy liquid tests were performed on different size fractions without any acceptable success. The concentration tests were performed using teetered bed separator (TBS) +shaking table, spiral concentrator+TBS+shaking table for different grind size. Based on the test results, 100% finer than 0.4mm was found to be optimum for grind size. Comparison of alternative circuits showed that the performance of both alternatives would be similar. A flowsheet was designed and operated for as 25 tph trial circuit in the existing plant. The results showed that the performance of the plant predicted was very close to the actual plant data. The paper describes the methodology used, presents the experimental data and actual performance figures.INTRODUCTION Turkey is one of the largest chromite producers in the world. Since 1850, chromite mining found industrial applications and geographically spread along six different regions in Turkey. Although the reserves in these locations are not as rich as the big producers, they are regarded as very valuable due to Cr/Fe ratio in terms of chromite utilization standards (1, 2). In this period, significant portion of high grade (=35% Cr2O3), directly marketable ore deposits have already been produced. According to General Directorate of Mineral Research and Exploration (Turkey) data; 83% of the known chromite deposits of Turkey which makes 242 341 000 tons in total, is consisting from the deposits those have a Cr2O3 grade lower than 10%. Only 5% of the known deposits (13 087 000 tons) has a grade of directly saleable (2, 3). Gravity concentration methods are well-known processes for chromite beneficiation and there are plenty of plants in the world and Turkey using these methods. As different equipment combinations can be used for the same enrichment method, different methods can also be used in combination for plant designs (4). Beneficiation of low grade and problematic chromite ores may lead to use these method and equipment combinations (5, 6). Ore liberation, the grades of Al2O3, SiO2, FeO and Cr2O3 in the obtained concentrate, Cr/Fe ratio, some physical and chemical properties between gangue and minerals (i.e. specific gravity, magnetic property, color, etc.) designate the selection and combination of these methods and equipment (7)."

Jan 1, 2017

By G. T. Lapidus, O. J. Solis-Marcial

Currently, ores with high-grades of copper oxides and secondary sulfides have become increasingly scarce, which has encouraged industry to look for alternative raw materials to obtain copper. The problem is that primary sulfides are difficult to dissolve at near ambient conditions. Proposed hydrometallurgical processes have not been implemented beyond a pilot or demonstration scale. One of the principal disadvantages is that the majority of these processes are not viable with ores that contain less than 4% copper. One of the more recently proposed techniques involves the use of organic solvents in the dissolution of copper concentrates with a chalcopyrite content of between 20 and 30%, which has shown high efficiency. The present research explores the ability of this process to leach copper from low grade chalcopyritic ores (<4% Cu) at different temperatures ranging from 20 to 50°C. It was found that depending on the temperature, high percentages of copper were extracted in 40 to 100 minutes, using different oxidants. Additionally, distinct leaching behavior was observed with each oxidizing agent. In some cases, the extraction kinetics adjusted to the diffusion controlled shrinking core model.

Jan 1, 2014

By C. J. Thompson

Two sulfur compounds--the 2,2,5-trimethyl- and the 2,2,5,5-tetramethyl derivatives of thiacyclopentane--were identified in Wilmington, Calif., crude oil, using microdesulfurization and gas-liquid chromtography techniques.

Jan 1, 1963

By T. A. George, David J. Sellmyer

"The concept of achieving a useful high-energy-product magnet through appropriate nanostructuring of known hard and soft phases has been tantalizing researchers since the idea was first proposed. The fabrication of exchange-coupled nanocomposite magnets faces several challenges including aligning the easy anisotropy axes of the hard-phase grains. Here we investigate experimentally two-phase nanostructures of hard Lio-ordered FePt and soft iron-rich/cc Fe(Pt). The Fe-Pt thin films were produced by epitaxial cosputtering onto MgO (001) single-crystal substrates which lead to strong (001) texturing. The measured hysteresis loops indicate nearly ideal exchange coupling. Excellent magnetic properties are obtained, with largest values of coercivity (51 kOe), saturation magnetization (1287 emu/ cm3, J, = 16.2 kG), and nominal maximum energy product (58 MGOe).1. IntroductionA key figure of merit for permanent magnets is the maximum energy product (BH)rrw.x. The achievable maximum energy product is determined by a magnet's saturation magnetization M, and its magnetic anisotropy. For example, it is well known that (BH)rrw.x :S 4n2M,2• In the past, record energy products have been the result of discovering new compounds with high values of magnetization and anisotropy. However, finding new compounds with better magnetic properties than the current record-holding magnet Nd2Fe14B has proven to be difficult. A different approach is to exploit the exchange coupling mechanism between known hard and soft magnetic phases to enhance the maximum energy product [1-5]. In such a composite system, high coercivity is achieved due to the anisotropy of the hard phase as well as a nanostructure which prohibits large-scale domain wall reversal mechanisms. Magnetization is enhanced by the soft phase and loop squareness results from texturing of the hard phase easy-axis as well as complete exchange coupling between the coexisting hard and soft grains."

Jan 1, 2012

By Zoltan Hajnal

Magnetic studies have been carried out on 88 surface and 157 underground samples from the Coronation Mine area of northern Saskatchewan. The intensity of the surface samples was compared to trace element determinations from the same locality. A good correlation was found between the titaniferous constituent of the rocks and the intensity of magnetization. From the direction of the remanent magnetism, two virtual geomagnetic poles were determined -latitude 12° 54&apos; North, longitude 158" 17&apos; West; and latitude 23" 42&apos; North, longitude 163° 45&apos; West. The sulphide ore specimens showed anisotropic susceptibility characteristics. A relationship was found between the measured maximum susceptibility values of the ore specimens and the direction of the tectonic forces which are considered to have formed the structure at the Coronation mine. Introduction T HIS paper summarizes the results of a study of the magnetic properties of samples from well-known Precambrian formations. The observed data give information for an interpretation of the magnetic field conditions in Precambrian times. The high magnetic intensity values indicate the importance of the study

Jan 1, 1965

By Bolger Witthaus

"High performance production under challenging geological conditions is a product of several parameters. Main factors are the technical equipment and the knowledge in processing. The design and the support system of maingates must also be taken into consideration. The extraction of seams in German underground hard coal mines of RAG in a range of heights between approximately 1.1 and 4.0 m ( 4 and 13 ft) is done by plow and shearer technology. A complete system for quality management of production is required. The process examination of processes begins with procurement of the equipment. Education and training of the engineers and specialists, as well as for the miners are requirements for success as well.This report gives an overview of RAG measures for achieving high performance. Starting with examination of the processes accompanying procurement of equipment, the following important elements are described. Standards in education and training, technical design and elements of automated processing using stateof- the-art in control systems are critical to this system.The application of automation plays a decisive role in modem coal mines. The latest development in German coal mines is the fully-automated shearer system for longwalls. This helps to enhance safety, particularly in difficult ground conditions, by removing the shearer and shield operators from the immediate mining activity.INTRODUCTIONLongwall mining in carboniferous strata in Germany faces various challenges. Different longwall systems are used to mine up to 24 seams, each with a thickness between 1.1 m (3.6 ft) and 4.0 m (13 ft). High stresses due to a depth of up to 1,400 m (4,593 ft) requiring pillars between the panels, require special systems for roadway development, roadway support and reinforcemen.t as well as for longwall advance operations. Two main types of equipment for extraction are shearer and plow systems. While shearers are utilized for seam thicknesses above approximately 1.8 m (6 ft), plow systems can be used for smaller seam thicknesses between 1.8 m (6 ft) and approximately 1.0 m (3 ft)."

Jan 1, 2010