Search Documents

By J. C. Agarwal

A significant portion of the, coal mined by U. S. Steel is beneficiated to upgrade the quality of the resultant coke to meet blast-furnace requirements. Primarily because of degradation from modern mechanized mining methods, a considerable quantity of the coal to be beneficiated is in the 1/4-inch by 100-mesh size range. In the cleaning plants, this coal is usually cleaned on concentrating tables and then mechanically dewatered in solid-bowl centrifuges to 9 to 14 percent water. At some plants, to further decrease the amount of water shipped with coal, and to improve the coking characteristics of the coal at its destination, mechanical dewatering is followed by thermal drying. At U. S. Steel's-Alpheus preparation plant at Gary, West Virginia, approximately 50 percent of the total coal produced is in this fine size range, and two fluidized-bed dryers are used for the thermal drying step. The two fluidized-bed dryers are 14 feet in diameter and were designed by the Dorr-Oliver Company. Although the original design called for a rate of drying equivalent to 37 tons, of moisture per hour, presently they are removing twice that amount. This paper describes, the major problems encountered' in operating these dryers at the present, high capacities and how they were overcome.

Jan 1, 1963

Growing concerns of climate change and its potential association with the release of greenhouse gasses to the atmosphere have prompted possible legislation which would require minimization of greenhouse gas emissions. Carbon dioxide and methane, both of which largely contribute to the greenhouse effect, have direct links to the fossil energy industry sector. Specifically, the combustion of one ton of coal produces between one and three tons of carbon dioxide, dependent upon the carbon content and heating value of the combusted coal. Additionally, coal mine methane (CMM) released through a mine?s ventilation system has a radiative trapping impact approximately 20 times greater than that of an equivalent mass of carbon dioxide. The capture of coalbed methane (CBM) prior to the mining process and its utilization as an alternative energy source provides the possibility of a decreased carbon footprint. Domestically, the past 25 years have seen a significant expansion of the CBM industry. Internationally, in developing countries such as China, the need for western coal degasification technology is growing. A collaborative, international effort will be required to initiate a recognizable decrease in global greenhouse gas emissions. This paper identifies the potential decrease in equivalent carbon dioxide emissions through effective degasification at a hypothetical longwall mine located in China. Advanced, three-dimensional gas reservoir simulation software will be utilized to determine the maximum feasible CBM recovery in a low permeability, high gas content reservoir prior to the mining process.

Jan 1, 2010

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005

By Stanley O. Reichert

At nuclear facilities, three types of radioactive waste must be managed: (1) high-level liquid waste containing fission products from the chemical separation of irradiated uranium, (2) low-level condensates from the concentration of the high-level waste, and (3) dry solids such as obsolete process equipment, spent ion exchange resins, and irradiated metal scrap. The geological and environmental characteristics of a site are important considerations in planning the waste management program. At the Savannah River Plant, low-level liquids and dry solids are safely and economically placed in the soil where the geologic and hydrologic conditions are favorable. Within the general area where the waste originates, studies are made to locate seepage basins and burial grounds in the most favorable sites: (1) soils should have a high ion exchange capacity and moderate to low permeability, (2) the water table should be deep, and (3) burial sites should be relatively distant from the nearest flowing stream.

Jan 1, 1968

By Franziska Wolf, Rainer Ellmies, Helmut Mischo

"Mining is an important part of the economy of Namibia. In 2016, 11.1 percent of the GDP was the result of mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists of an underground mining operation.The global annual production of fluorspar is approximately 5.4 to 6.3 Mt (6 to 7 million st) (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu has produced on average about 45 kt/a (50,000 stpy) in recent years (U.S. Geological Survey National Minerals Information Center, 2015).The Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an openpit mine with four individual pits (A-D) since 1980. In 2014, the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently, Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village.The intent is to develop a concept for the further underground development of the mine. There are still about 6.3 Mt (7 million st) of measured resources left in the deposit, with an average grade of 27.5 percent CaF2. This study focuses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged.For solving the task to design the mine, a site visit for data collecting was conducted. Resource estimations were calculated based on existing drill data, and consequently, block models were created. The development of the mine design included the selection of the most suitable mining method, mining technology and mine organization. Moreover, some economic considerations are pointed out, followed by a profitability assessment."

Jan 2, 2018

By L. Tikasz

The primary purpose of ore hauling model studies is to capture the variability of the ore delivery ? stockpiling process in order to improve the estimation of equipment capacities and achievable throughputs. The operation of a mine-to-site ore delivery system is the subject of a number of challenges. Typically, ore is hauled by a given combination of trucks, conveyors and trains. In addition, ore loading, ore transferring to another means of delivery, stockpiling, reclaiming, and further deliveries involve many other types of equipment. The concurrent operation of all these units is scheduled; nevertheless, they are subject to planned maintenance and random breakdowns. To support our engineering design work on ore hauling operation, discrete event type models were built for each specific task. Then, due to recurring demands, an ore hauling library was gradually compiled. The now available model library allows fast and efficient simulation of various mine-to-site hauling arrangement, adaptable to various mining and mine construction operations (e.g. bauxite, iron ore, copper ore and coal).

Aug 1, 2013

By Dan Eyde

Low levels of thallium were detected in the mine water drainages, and process water discharges of western mining and smelting operations. This required remediation under state regulatory standards, which allow discharges of no more than .0017 ppm thallium in mine water discharges. Influent streams containing thallium can be mitigated to state discharge standards after a single pass through the series of fluidized upflow columns. Test work to determine the optimal flow rates used pilot scale systems at two separate locations treating 5 - 25 gpm of effluent. The test system at the gold mine mimics the full-scale system, which will be based on the existing upflow carbon tanks that have been converted to zeolite columns. The system installed at ASARCO's East Helena smelter has a far more complex influent stream with a high loading of competing cations. Nevertheless the columns filled with CABSORB® are successfully mitigating the thallium contamination. CABSORB® ZS500RW is a product based on the sodium analog of the zeolite mineral chabazite named herschelite.

Jan 1, 1998

By P. C. Good

The work reported here was undertaken by the Federal Bureau of Mines to investigate new methods of preparing high-purity metal. Tungsten hexachloride was prepared by direct chlorination of scrap tungsten metal and by treating tungstic oxide with carbon and chlorine. The resulting tungsten hexachloride was purified by distillation and reduced win: sodium, magnesium, or hydrogen. The metal prepared by these techniques was at very high purity after arc melting but of variable quality prior to arc meIting. Metal recovery ranged from about 40 to 90 percent of theoretical values, It was found possible to deposit a smooth, dense coating of high-purity tungsten on the inside of a heated tube by vapor-phase reduction of tungsten hexachloride at reduced pressure.

Jan 1, 1961

By Klaus Rabensteiner, Klaus Chmelina

"INTRODUCTION Urban tunneling is often related with special geotechnical risks. Typical causes are difficult (hydro)geological conditions, a very low overburden and the presence of critical and vulnerable (infra)structures in the influence zone of the construction (e.g. existing tunnels, roads and pavements, sewer pipes, gas and power lines, landmarked buildings, historic monuments). To manage these risks appropriately, an early detection and warning of unexpected behavior of the affected geotechnical objects ground and tunnel, as well as existing structures are mandatory. To accomplish this, the design and execution of a dense geotechnical monitoring program is of high importance. In more detail, this means specifying and performing a systematic and continuous acquisition, processing and analysis of monitoring data to support decision making. In recent years the development of new automatic sensors and (wireless) data transfer techniques and the general trend towards an automatic acquisition of monitoring data has led to an enormous increase of data production frequencies and volumes. In order to handle this data explosion efficiently, information systems and geo-databases have been developed and used successfully in many projects. They represent IT tools that support the different tasks of a given geotechnical monitoring program including data acquisition, transfer, check, processing, backup, analysis, distribution, reporting and, last but not least, alarming. Meanwhile, some tools already have developed the capability to connect to other theme-specific databases used in the project and, thus, serve as a central data management system for all kind of digital data produced. This makes possible the implementation of further useful functions and services supporting tunneling tasks such as machine control, tunnel simulation, geological prediction, process optimization, etc. where data from different engineering disciplines must be combined and processed in an integrated way. In the following chapters our aim is to describe how monitoring data management, geotechnical monitoring, alarming and reporting are organized and technically implemented at the metro project Cityringen in Copenhagen (Denmark). We want to highlight the specific role and tasks of the used tunnel information system in the project, and particularly inform on the most relevant challenges."

Jan 1, 2016

By Supachai Surapunt

The distribution behavior of V A minor elements (As, Sb and Bi) in the smelting stage of the Mitsubishi process were evaluated thermodynamically based on thermodynamic data and operating data. The fractional distributions between the gas, slag and matte phases considered as the degree of vapor saturation of 1.0 are as follows: 53.8, 27.2 and 19% for As, 23.6, 56.6 and 19.8% for Sb, and 91.3, 1.1 and 7.6% for Bi, respectively. Arsenic is mostly distributed to the gas and slag phases. It is effectively eliminated by volatilizing and slagging. Antimony is mainly in the slag phase, which is suitably removed by slagging. Bismuth is easily vaporized to gas phase. The degree of vapor saturation has a large effeet on the distribution behaviors of the three elements between the three phases. The amount of a minor element in the charge has an effect on the distribution of As but no effect on the distributions of Sb and Bi. Increasing matte grade and temperature results in the change of distributions for As and Sb, significantly. The change in the distribution ratio between slag and matte phases also considerably affects the distributions of As and Sb. The distribution behavior of Bi is not significantly changed by the change in matte grade, temperature and distribution ratio.

Jan 1, 2003

By Bingchen Chen, Zhitong Sui, Junwei Ma

"In the blast furnace slag, titanium disseminated in various mineral phases Titanium could be concentrated mainly in perovskite, which could be selectively precipitated and grown by optimizing the operation factors like the slag composition, temperature of heat treatment and additive agents. This study aims at establishing the titanium slag mineralogy and its distribution in the treated slag and the as-received slag, as well as the methods of perovskite separation. After heat treatment, the grain size was grown from 5 - 20µm to 80 - 200µm, the distribution of Ti02 in perovskite was increased from 48% to 81 %, the morphology was changed from snow-shaped grain to coarsening dendrites or equiaxed crystals. A concentrate were produced by gravity separation analyzing 35.25% Ti02 with a recovery of 68.28% and a tailing analyzing 9.53% Ti02 , and a possibility of flotation upgrading was discussed. I INTRODUCTION CHINA is rich in mineral resources of titanium, 92.4% of which is vanadium-titanium bearing magnetite. About 53% titanium were in iron concentrate after mineral processing, by which the blast furnace slag containing about 25% TiO2 were produced[11 • The content of TiO2 in such slag is too low to separate titanium dioxide, and it is also too high to produce slag cement[21. It has been accumulated to 50 million tons so far, which is still increasing at a rate of 3 million tons per year, and results in a waste of titanium resources and pollution of environment. Due to the dispersed distribution of titanium component in various mineral phases, very fine grain(<10µm) and complex interfacial combination, it is very difficult to recovery titanium component from the slag by traditional separating technique. In this paper, a novel technique to recovery titanium from the waste slags was proposed [3H4l, on which three continuous processes were involved: selective concentrating, selective growing and selective separating. Perovskite was designed as a titanium-rich phase, in which the most titanium was concentrated promptly, then perovskite could be selectively grown and coarsened by optimizing the heat treatment and the appropriate additives [ 5l[6l. The grain size of perovskite phase was larger than 80 µm, and the crystals appeared as coarsening dendrites or equiaxial grains like lump."

Jan 1, 2000

By K. J. Maggs

The U.S. Bureau of Mines has investigated the chemical vapor deposition of diamond films on tungsten substrates. The effects of deposition parameters on the adhesion of the films was determined. The films were produced using a hot filament chemical vapor deposition system. Parameters investigated were substrate temperature and methane concentration in the feed gas. Film quality, morphology, and composition were characterized by scanning electron microscopy and Raman spectroscopy. Adhesion testing was performed using an indentation technique, and the results were quantified by relating adhesion to interface fracture toughness. Diamond films with well-faceted crystalline morphology with grain size greater than 1 µm had poor adhesion properties regardless of substrate temperature or methane concentration. Diamond films with smooth morphologies consisting of rounded clusters of small (<0.2 µm) diamond crystallites and amorphous carbon phases displayed much higher adhesion, although the conditions that led to the growth of these films are not understood.

Jan 1, 2010

By Bruce Macdonald

Operational reservoir management activities such as cyclical steam, water or CO2 injections frequently cause surface micro-deformation. InSAR monitoring from space based sensors of this surface deformation has become a valuable approach to confirm and monitor extraction and injection activities. Sequestration of CO2 into deep saline aquifers is discussed as an important long term solution to slow future climate change. This method requires reliable continuous monitoring to assure that captured CO2 is sequestered in the substrate for ?all time? (typical minimum requirement by law is 20-30 years). We have shown that combining flow and deformation modeling with spaceborne synthetic aperture RADAR interferometry (InSAR) measurement of ground uplift caused by the underground release and spreading of the CO2 can be forged into a powerful tool to monitor sequestration. We used a novel InSAR approach to resolve the surface motion over the In Salah, Algeria CO2 sequestration site. Our approach exploits all information contained in an interferometric stack by exploiting both persistent distributed as well as persistent point scatterers. Displacement time series are obtained with a network inversion approach applied after topographic error and preliminary atmospheric correction of the network (dual-scale technique). After inverting the original network data to common master we then use an advanced spatio-temporal filtering scheme to remove the remaining atmospheric phase components down to scales of 1 km or less. By comparing final displacement series from multiple interleaving InSAR stacks we show that the accuracy of our refined solution to detect uplift outside of significant temporal data gaps in the InSAR stack is significantly better than 1 mm per year. We further show that accuracy and robustness to data gaps are both significantly improved by co-inverting multiple datasets with the same and different sensors. This co-inversion method also allows the seamless continuation of the monitoring from one sensor to another.

Jun 1, 2012

By N. J. Tannyan

Laboratory bath smelting tests were conducted to determine the feasibility of smelting nickel- copper concentrate directly to a low iron matte in one step. Concentrate, air/oxygen and a silica flux were fed to a matte-slag bath kept in MgO crucibles at I 300°C. Various oxygen enrichments and smelting rates were used to maintain 0.5 to 2 wt% iron in the product matte. The slag losses are comparable to those obtained under similar industrial conditions. Due to the highly oxidizing conditions required to produce mattes with low iron contents, it is not recommended to target iron contents below about 2% in the matte. The specific bath smelting rates were equal to or higher than those in various industrial bath smelting processes.

Jan 1, 2003

By E. Peek, L. Becze, K. Reading

"Gallium oxide is an important semiconductor material used in optoelectronic devices (flat panel and solar cell) catalysts and sensors. One of the methods to produce ?-Ga2O3 is the so-called hydrothermal route. It is practiced by Neo Gallium Compounds and comprises of two steps: (1) the production of mainly gallium-oxy-hydroxide in a pressure vessel by reacting metallic gallium with water at 200-220 ºC and (2) the calcination of gallium-oxy-hydroxide at 700-750 ºC to convert it into ?-Ga2O3. This paper describes this pressure hydrometallurgy process supported with relevant thermodynamic data and presents the characteristics of the ?-Ga2O3 powder produced for commercial purposes. INTRODUCTIONGallium is a relatively new metal, having been predicted by D. Mendeleev in 1871, discovered by P.E. Lecoq de Boisbaudran in 1875, and first commercially produced in the USA in 1943. Gallium is not rare, being more abundant in the earth crust than antimony, bismuth, molybdenum, silver and tungsten. However, few gallium minerals exist in nature, and the dispersion of gallium within other minerals add to the complexity of its recovery. In practice, gallium is found in dispersed state primarily in bauxites and in some sphalerites, and, to a much smaller extent, in some coals. At present, a very large proportion of the primary gallium in the world is recovered as a by-product of aluminum plants, mostly Bayer plants, where gallium is extracted from a bleed of the Bayer liquor (Roskill, 2011). In 2011, world production of primary gallium was estimated at 200 metric tonnes. In addition, there is a significant contribution of recycling to the overall yearly availability of the metal.Gallium exhibits fairly remarkable properties: it is liquid above 29.76 ºC, can be supercooled, and with its high boiling point (2204 ºC), is the metal with the widest liquid range. Gallium is magnetic, and is an excellent conductor of both heat and electricity. Gallium also displays a marked anisotropic electrical conductivity (Roskill, 2011). All these properties render gallium almost irreplaceable in the semiconductors (GaAs, GaN, GaSb, GaP wafers) and the optoelectronics industry (flat panel, solar cell)."

Jan 1, 2012

By Y. C. Liu

Ningxiang-type iron deposit is a most important sedimentary oolitic hematite deposit in China. Its? detected ore reserves are 3.72 billion tons, which is 73.5% of all detected reserves, and there are about 10 billion tons of prognostic resources. It is considered as the ?poor mine? for a long time be-cause of its difficult prooerty. But based on the ore characteristics of different deposits, the technological characteristics of ore are different with great diversity in ore baring horizon, distribution range, deposit scale, ore petrology, ore mineral assemblage and iron content. Through the study of deposit features and technological mineralogy of different Ningxiang-type of iron deposits in China, and based on industrial types and natural types of ore deposits, we divide different technological types according the technological features of the ore such as mineral composition, particle size, dissemination, occurrence of useful elements and harmful elements, the main physical and chemical properties of mineral and geological conditions of deposits, etc, moreover, propose the different utilization, mineral processing technologies and product schemes for the different types of ore.

Jan 1, 2014

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By Jian Pan, Zhen He, Deqing Zhu, Shouyan Yue

"The differences of raw material characteristic among six kind of iron concentrates and the influences on ballability were studied from the aspect of the size distribution, specific surface area and particles morphology. The results show that the specific surface area of iron concentrates has crucial influence on ballability, and the effective method of improving ballability for weak ballability iron concentrate has been found. It is of important guidance for Chinese steel mills to import and use iron concentrate from the whole world.IntroductionChina's steel industry has developed rapidly in recent years, crude steel production in 2011 is an unprecedented 683 million tons, which is almost half of the world crude steel production, and it is equivalent to the total sum production of the nations which rank at 2,3,4,5 and 6 in the world [1]. In order to match the development of steel industry, the blast furnaces are becoming larger and more modernization, therefore charging burden of higher quality is requested, and the reasonable blast furnace burden structure is more and more important, at the same time, for iron ore powder sintering process's continuous improvement and development, another method providing ""concentrate"" for blast fumace-pelletizing is also taken seriously. The grate-kiln method of pelletizing has achieved great development for its unique advantage, and in just a few years, there are over 60 rotary kiln production lines have built or being built in China, the sum of pellets has reached to more than 140 million [2, 3]. The rapidly growth of pelletizing yield demands diverse source of pellet, which include not only domestic magnetite concentrate, but also imported hematite which is high in iron and low in silicon. Usually the ratio of imported hematite concentrate increased gradually. The imported hematite concentrate has high grade and fine particle size (the content of -0.074 mm mostly higher than 90%), but the ballability of part of the concentrates is poor."

Jan 1, 2013

By Jalna R. Zatko

The Bureau of Mines has developed and constructed an apparatus that is capable of measuring concentrations of high-molecular-weight polymers in solution at 10 ppm and less. A means for determining low concentrations of polymeric solutions was devised that was independent of slight fluctuations in solvent quality in order to measure polymers in effluent prior to recycling of the recovered solution. The concentrations of polymers ore related to a measured pressure drop observed during turbulent flow of the solution. Low concentrations of polymers of ethylene oxide and acrylamide (frequently used as flocculants for clay waste systems) in aqueous and salt solutions have been successfully measured on the apparatus constructed by the Bureau.

Jan 1, 1981

By Andrew J. Regis

Resource figures for bentonite clays are generally based on stratigraphic, sedimentary geologic data and drilling and sampling. Estimates of bentonite resources and/or reserves commonly found in the literature report on bentonite occurrences in specific localities or areas but none on any documented comprehensive estimates of bentonite resources. From 1974 thru 1977 the Bureau of Land Management conducted extensive studies of the resources of commercial grade bentonite in the three state region. These investigations consisted of: 1. Stratigraphic and geologic sampling with supplemental drilling data, followed by geostatistical analysis. 2. Data compiled from a systematic search of county and state records on mining locations, leases and acreage filed for bentonite. Estimates of resources of commercial grade bentonite using industry parameters were calculated from these data sources. It is concluded that there exists from 1.5 to 2.4 billion tons of in-place bentonite in Wyoming, Montana and South Dakota. Assuming a 5 percent annual growth rate for the industry, this would indicate a life of 62 to 73 years.

Jan 1, 1979