Search Documents

As part of the Australian Mineral Industries Research Association (AMIRA) P9 project, methods of characterising both the ore and the machines in flotation circuits have matured considerably over the past 15 years. Machine characteristics include gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity. Ores can be characterised in terms of floatability parameters on a size and mineral basis. Measurements have been performed on various copper plants in many countries around the world over the last 5 years. This paper outlines the cell and ore floatability characteristics of each copper plant and provides a discussion on the differences between these plants. In general, most porphyry copper ore bodies are processed at high tonnage through several parallel banks of cells at each stage of flotation. The floatability parameters of these copper ores are very similar in terms of rate of flotation and proportion of fast, slow and non-floating material. The cell characteristics are also similar, with superficial gas velocity, bubble sizes, and gas hold-up values being of similar magnitude. Investigation of the similarities and differences of the modem copper flotation circuits has allowed an increase in understanding of the particularities of copper flotation. Comparison against other copper circuits provides a benchmark and opportunities for future optimisation.

Jan 1, 2007

By S. Onuki, T. Ando, M. Tejima, R. Enomoto, Y. Okada

"Al–Si–Cu–Mg die casting alloys are widely used in the automotive industry, and recent advancements in high pressure die casting technology enable heat treating products to achieve desirable properties. However, CO2emissions associated with die-casting production lines should be reduced to address the global warming issue. In this study, the relation between the microstructures and thermal stability of precipitates formed during isothermal aging at 423, 485, and 558 K of Al-11.0 mass%Si-1.8 mass%Cu-0.2 mass% Mg (JIS ADC12) was investigated using Vickers hardness tests and transmission electron microscopy (TEM). The hardness tests and TEM results showed that Si compounds and Al–Cu compounds enhanced the mechanical properties of the alloy and that the predominant compound affecting the mechanical properties differed between specimens treated at 423 K and those treated at 558 K. Moreover, additional aging at 423–458 K resulted in a material with a Vickers hardness higher than that of the isothermally single-aged material. Differential scanning calorimetry, differential elemental analysis, and selected-area diffraction analysis using TEM suggested that the combination of Al–Cu compounds precipitated at low aging temperatures and Si compounds precipitated during preliminary aging increased the mechanical strength, resulting in a maximum hardness of 130 HV.INTRODUCTIONAl–Si–Cu–Mg die casting alloys have well-balanced mechanical properties, machinability, and cast ability. These alloys are therefore widely used in the automotive industry because of their superior characteristics, accounting for>90% of the aluminum used in die casting production. As a substitute for iron-based materials, these alloys have contributed to the development of lightweight vehicles.Dong et al. (2014) reported that the heat treatment of die casting materials is effective for changing their dimensions under high temperatures as a result of the precipitation of solid-solution elements. Recent advancements in high pressure die casting technology have led to the application of heat treatments of Al–Si–Cu–Mg alloy products to reduce fuel consumption and satisfy customer needs. Although attempts to reduce CO2emissions have focused on fuel consumption in cars and fuel efficiency regulations have become increasingly strict in recent years, CO2discharged from production lines should also be reduced without adversely affecting the properties of the product. Heat treatments for artificial aging after solution treatment (T6 treatment) and after casting (T5 treatment) are CO2discharge sources, which together with a holding furnace account for >80 % of the CO2discharged during the casting process."

Jan 1, 2018

By Mohammadreza Jalali

Alberta contains over 400 billion barrels of viscous crude oil in fractured carbonates but there is no viable extraction technology as yet. Petroleum geomechanics has become a vital part of the assessment of such hydrocarbon reserves, especially for naturally fractured cases, which are particularly challenging in terms of accurate recovery prediction because of joint fabric complexity and lithological heterogeneity. As a result of interconnected fractures, transport properties of fractures (mostly permeability issues rather than thermal effects) are affected by production and injection activities that change the pore pressures, temperatures, saturations, and effective stresses. Enhanced oil recovery methods involving massive amounts of fluid injection (hot or cold) at high pressure (pinj) may be used to mobilize and produce the oil; therefore, deeper understanding of the fractured systems is desirable. Pressure and temperature variations in a fractured reservoir change the in situ stresses in the reservoir and surrounding rocks; this affects fracture apertures, radically changing the bulk flow properties because flux rate is highly sensitive to aperture. Hence, coupled pressure, temperature and effective stress changes must be considered for fractured reservoirs under a thermo-hydro-mechanical (THM) coupling approach.A hybrid FDM/DDM coupled method is presented to couple pore pressure and stress around a fracture in an impermeable matrix block. Deformation and stresses are calculated in each time step and then fracture permeability, which is the most sensitive petrophysical parameter in fractured reservoirs, is updated based on the fracture aperture variation. This model is then verified with UDEC (Universal Distinct Element Code) which uses a discrete approach to cope with fractured rock mass behavior.

Jun 1, 2012

By J. F. Wright

Introduction Previous to 1924 the mining fields of Manitoba and adjoining territory had not been prospected in detail, and the reports of the exploration of the mineral discoveries to that date had been discouraging. As a result of the apparent failure of all the mining operations, some considered that geological conditions in the country westward from lake Superior extending across western Ontario, eastern and northern Manitoba, and northern Saskatchewan, were different from those in the northeastern part of Ontario, where large gold mines had been developed. Discoveries of importance thus were necessary to renew interest in the mining possibilities of this part of the Canadian Shield, and the successful operations at Flin Flon and Howey in large part were responsible for the beginning of the present activity in what may be described as the part of the pre-Cambrian Shield within central Canada. In Manitoba, the more important developments at present are in the Central Manitoba, Gods Lake, and Knee Lake fields. The large area from west of Flin Flon east to Herb Lake, also, is being explored carefully for gold deposits of merit. A number of properties in Red Lake, Woman Lake, and Pickle Crow areas are being drilled and explored underground. Many of the mines of the Lake of the Woods area, that were producing gold 30 years ago, are re-opened, and new prospects in this field and in the country to the east are being explored. The recent development of Little Long Lac mine in an area near the railway, and considered by some to have been thoroughly prospected years ago, has stimulated interest in the areas formerly prospected. In the autumn of 1934, the belts of greenstone and sediments in the country east of lake Nipigon were staked, and deposits in these fields will be explored in detail this year. This paper is presented to discuss the general features of the geology and gold deposits of the various prospecting fields in Manitoba and adjoining territory. Details of a number of the areas and mines will be presented at this meeting in papers by Barton on Little Long Lac, Tanton on Sturgeon River, Baker on Gods Lake, and Brownell and Kinkel on Flin Flon. Although mining was not active in most of this territory previous to 1930, geologists of the various government departments continued field studies and interesting reports were issued.

Jan 1, 1935

By G. D. Jermain

The Bureau of Mines investigated the Gypsum-Camel deposit on Iyoukeen Cove Chichagof Island, Southeastern Alaska, from April 21 to August 26, 1948, as A part of the United States Department of the Interior program for developing an Alaskan construction industry. As gypsum is one of the components necessary for the manufacture of cement and one of the raw materials for plaster and plaster-board products, it is desirable to locate and develop a readily accessible deposit of gypsum in Alaska. In 1928, B. D. Stewart of the Territorial Department of Mines surveyed the gypsum deposits at Iyoukeen Cove, and during the summer of 1946 George M. Flint, Jr., and Edward H. Cobb of the Federal Geological Survey examined and mapped the old workings at Gypsum Creek and the prospect at Iyoukeen Cove. Both the Territorial Department of Mines and the Federal Geological Survey recommended the Gypsum-Camel prospect as warranting a diamond-drilling program by the Bureau of Mines. The Bureau of Mines project consisted of cleaning out and sampling, the old underground workings and diamond drilling from the surface to ascertain the lateral extensions of the deposit.

Jan 1, 1952

By Alfred G. Hoyl

The author, in exploring a virgin area vertically in two known ore shoots requiring decline shaft sinking, drifting, crosscutting and diamond drilling, chose to use electric, electric hydraulic, and diesel rubber-tired equipment. A rebuilt hoist, and electric hydraulic shaft shovel (mucker), hydraulic sinking drills, single boom electric hydraulic jumbo, electric hydraulic LHD, and electric hydraulic diamond drill were used successfully. Slides of the equipment and its use are shown. The advantages and disadvantages of the equipment are discussed, together with costs and production.

Jan 1, 1984

By Jun Xiao, Jianwen Yang, Yanhong Dong, Daixiong Chen

"MANGOTE Surface oxidizied mine is a gold-bearing deposit in Congo's Mai-Ndombe Province. In the past decades, the ore has been exploited in a crude way by local farmers, which directly causes the severe processing difficulty and lack of economy of cyanide leaching. Hunan Research Institute for Non-ferrous metals (HRIM) is currently investigating options to recover gold through understanding the mineralogical characteristics of MANGOTE surface oxidized ore. Chemical analysis , X-ray diffraction(XRD) and Quantitative Evaluation of Minerals by SCANing electron microscopy (QEMSCAN ) were conducted on samples from mine site. The bulk analysis results showed that gold separation of gold from gangue minerals was feasible after grinding the ore samples to 86.53% -74µm and adjusting the pulp specific weight at 100g/L, and gravity separation was conducted with using spiral chute after grading of fine particles. The research results highlight relationship between mineralogical characteristics of abandoned ore and economy of comprehensive utilization that might be directive experience to similar cases. INTRODUCTION The occurrence state of gold in natural gold minerals determines the basic recovery and recovery effect of gold(Komnitsas, C., & Pooley, F. D. 1989). The occurrence of gold in the ore refers to the form of gold in the ore.Generally the existing state of gold can be divided into four major categories according to the viewpoint of the dispersion system: independent minerals and gold, a coarse dispersed system;colloidal gold, a colloidal dispersion; solid solution gold, is atomic ion dispersion; adsorptive gold, according to the adsorbed particle is the micelle or ion, respectively is a colloidal dispersion or ion dispersion(Mao, S. D., & Yang, R. S. 2009; Liu, J. J. et al. 2007; Horisberger, M., & Rosset, J. 1977; Li, Y., & Audétat, A. 2013).With the increasing technology of comprehensive utilization of resources,varied plants can now process different gold ores with various occurrence states(Neesse, T. 2014; 7. Ogundare. et al.2014)."

Jan 1, 2018

The Managalase area is remote and little visited by geologists or prospectors. Yet it holds the key to the tectonics and petrology of this part of Papua. The eastern Managalase plateau (M, Figure 1) lies between the Hydrographers andesite volcano (H) and Sesara shoshonite volcano (S) to the south of Popondetta on the Papua Peninsular. It contains over 30 small volcanic centres in an area of only 400 km2 . To the south and west lies the basic-utrabasic belt (B-UB) of the Morobe arc. This is the leading edge of oceanic plate obducted over the Owen Stanley Metamorphics during the lower Eocene time. To the east and southeast lies the Cape Vogel geosyncline where the western end of the Woodlark basin spreading centre enters mainland Papua. The extension of the spreading centre as a suture might pass as far as the southern margin of the Musa Coastal plain. A new pattern of plate tectonic motions has been determined by the global positioning system and the southern margin of the Woodlark plate has been redefined (Tregoning et al, 1998; Taylor, Goodliffe and Martinez, et al, 1999). The Managalase plateau is margined by two inferred faults. These outline a cusp protruding from the main basic-ultrabasic belt where these rocks are near the surface. The westerly arm of the cusp passes through the centres of the Hydrographers and Mount Lamington andesitic volcanoes. Mount Lamington overlies Quaternary alluvium and underlying Tertiary sediments (Arculus et al, 1983) but members of the basic-ultrabasic belt crop out on the southern flanks. The easterly arm of the cusp is an inferred shear zone (and ? fault) connecting up with the terminus of the suture on the Musa coastal plain. Movements on the two faults forming the cusp are thought to have produced the conjugate N-S, E-W faults on the plateau (Ruxton, 1966). To the east, and isolated, are the two large andesitic stratovolcanoes of Mounts Victory (V) and Trafalgar (T) which together form Cape Nelson. Mount Victory was last active in the 1890s. The Waiowa shoshonitic volcano explosion centres (W), last active in 1943 - 1944, lie near the suture adjacent to the actively rising Goropu mountains. Extension in these mountains is clearly demonstrated by the soil profiles being skeletal along a bounding fault and ageing uphill. The incision of small parallel ravines also dig deeper further upslope from the fault. To the south-east of Mount Suckling (K) the Dayman Dome is also an expanding mass. The Owen Stanley fault is parallel, and located to the south of the suture. The Mesozoic metamorphics form the backbone of the Papuan Peninsula. The intramontane Musa Trough is thought to date from the mid-Tertiary. At the eastern end of the trough Pleistocene and Recent ultrabasic breccias and alkali basalt crop out (Green, 1961).

Jan 1, 1999

By G. W. Poling

Sedimentation behaviour of siliceous mill tailings derived from a magnetite-chalcopyrite ore in fresh water, fresh water - sea water mixtures and full-salinity sea waters are compared. Results of batch settling tests are presented in the form of settling curves and solids flux curves. The addition of a few per cent of sea water markedly enhanced the zone sedimentation rate due to particle agglomeration caused by a reduction in zeta potential of the suspended solids. The presence of a small amount of residual, previously magnetized magnetite in the tailings also enhanced agglomeration and sedimentation. The significance of these results to submarine disposal of mill tailings is discussed.

Jan 1, 1973

By Horace Freeman

Introduction This paper is an amplification of the paper presented by the writer at the last (1930) Annual Meeting of the Institute (1), and is somewhat in the nature of a progress report upon the introduction of pyrite into the field of Canadian consumption. The burner installed at the plant of the Canada Power & Paper Corporation, St. Maurice division, has been slightly changed in dimensions and has been put into continuous operation during the past year. As predicted, it has been possible to somewhat increase the steam consumption and at the same time decrease the amount of sulphur remaining in the calcine. The grade of the sulphur-dioxide gas produced has been maintained very steadily at 12 per cent, and sufficient experience has been obtained to determine the renewal cost of continuous operation. The object of this paper now is to encourage the development of pyrite, particularly by-product flotation pyrite, as it is shown that there is a very definite field in Canada for this material and that all the previous objections to the use of pyrite have been overcome, and that the use of the material in practice in paper mills has been developed to such a point that the operation of manufacturing the sulphite cooking-liquor is as simple as, or simpler than, the present style of operation with the use of sulphur.

Jan 1, 1931

By Ryokichi Shimpo, Akio Fuwa

"In order to elucidate the present status of process-control technology, survey study has been made on the present process control schemes of representative copper smelting and converting processes in Japan. Conceptual control flow diagrams have been deduced and shown on respective functional reactors, i.e. drying, smelting, converting and fire-refining units, where the objective OUTPUT items are correlated to the INPUT variables through respective CAUSE-AND-EFFECT RELATIONSHIPSFuture view has been also discussed on several feasible and desirable improvement and refinement ~n measurements and control system for better copper smelting and converting operations.INTRODUCTIONIn other to seek for the better and efficient operation in copper smelting and converting process, survey study has been first conducted on the present process-control schemes of respective functional unit processes, i.e. drying, smelting, converting and refining unit processes, of representative copper production processes in Japan. Conceptual process flow chart of control scheme has been then deduced where output items are correlated to input items through the respective cause-and-effect relationships.After this survey study, future view has been discussed on the feasible and desirable improvement and refinement in the measurement and control system in these processes. Emphasis has been placed on the better and precise measurements of temperature, oxygen partial pressures in respective furnaces and end-point in converting and refining unit operations."

Jan 1, 1989

By N. P. Reddy

This paper describes an experimental setup for multiple-fan ventilation systems at the ventilation laboratory of the WVU Department of Mining Engineering. Housed in a 30 ft by 70 ft room, the experimental setup consists of three 18 in. variable-speed axial-flow fans, the 18 in. diameter fiberglass tubing and fittings for arranging networks, and the pitot tube measuring and data acquisition system. The fiberglass tubing and fans can be organized into the non-planner network of two fans or three-fans. It is mainly designed for studying the characteristic curves, operating points, and fan stall for the multiple-fan ventilation system.

Jan 1, 1992

By B. Zeifert, C. Martínez-Morales, A. Romero-Serrano, A. Pineda-Rivera, H. Martínez-Gutiérrez, G. Diaz-Sandi

In this work, the effects of CaO/SiO2 ratio and the FeSO4 and FeS2 contents on the stability of the mineralogical species in chromium-based slags were studied. The chemical stability was evaluated by leaching with an acid solution. The main Cr-compounds in slags with FeSO4 and CaO/SiO2=1 were FeCr2O4 and Ca3Cr2Si3O12, while Cr3S4 predominated in slags with FeS2. The slags with CaO/SiO2=2 mainly contained CaCr2O4. The highest Cr concentration levels in the leaching liquors corresponded to slags with CaO/SiO2= 2, and the lowest Cr concentration corresponded to slags with high FeSO4 or FeS2, owing to the stable binding of chromium in the compounds FeCr2O4, Cr3S4 and FeS•Cr2O3.

Jan 1, 2011

By K. Szczesny

This paper considers the integration of uncertain real-time logistics data for reactive construction scheduling. In order to manage a construction project efficiently, an accurate schedule representing the current project progress is inevitable. The quality and up-to-dateness of such a schedule depends on the availability of real-time data. Typically, real-time logistics data contain information about the availability of material, equipment and personnel as well as delivery dates and site conditions. The accuracy and inherent uncertainty depends on the location where the real-time data was acquired. Currently, the integration of such data into a construction schedule is a very time-consuming, manual and, thus, errorprone process. Therefore, this paper proposes a methodology that enables an automatic integration of such uncertain data into construction schedules. By integrating uncertainties into the existing schedule their impacts on the construction work can be evaluated. For this, discrete event simulation is applied. In order to model uncertain input parameters for simulation models this methodology applies the fuzzy sets theory. In combination with alpha-cut sampling technique, discrete model input parameters are obtained. By applying reactive scheduling with several discrete event simulation experiments, the results can be used to modify construction schedules according to agreed timeframes and costs. In order to demonstrate and validate the presented approach an example is conducted.

Aug 1, 2013

By ?. S. Yusupov, V. P. Isupov, N. Z. Lyakhov, A. G. Vladimirov, S. A. Kondratiev

"Considering the shortage of lithium reserves, the desirability has been shown of studying the possibility of processing into spodumene concentrates the concentration tailings and low-grade ore reserves at Transbaikalian Mining and Processing Project (ZabGOK). The mineral and chemical composition and the particle size distribution of the mineral feed, separability and recoverability of spodumene have been studied, forming the basis for the development of a concentration process and flowsheet for the studied mineral resource. Prospects have been established for impact ore grinding in a disintegrator, the efficiency of mechanochemical processes has been shown in the separation of quartz and feldspar and the recovery of lithium from concentrates.INTRODUCTION Lithium is widely used in various industries - nuclear power engineering, defense technology, power generation, ceramics, special-purpose glass and other technologies. The increasing demand for lithium and its compounds (lithium carbonate and hydroxide) for use in the manufacture of high-tech products (lithium-based materials for chemical sources of electric power and electrochemical energy) explains the need for establishing a sustainable raw material base (Mohr et al. 2012; Moores, 2007). The main sources of lithium are spodumene pegmatites (Vladimirov et al. 2012; Garret, 2004), brines (salars), and hydromineral materials (Garret, 2004; Zeng and Liu, 2009; Kotsupalo and Ryabtsev, 2008). However, in view of the absence in Russia of extractable hydromineral resources of lithium, the practical significance of spodumene ores remains decisive. Russia controls some of the world’s largest reserves of rare-metal pegmatites holding over 8 million tons of Li2O: approximately 7 million tons on the Kola peninsula and 1 million tons in the Sayan mountains. The main lithium mineral in pegmatites is spodumene LiAlSi2O6 containing 8.1% Li2O. It can be efficiently recovered by gravitational concentration and flotation. However, most of the deposits are located in remote areas and none is currently developed. In this connection, special research is focused on technogenic raw materials, which are increasingly seen as a solution to the resource base problem (Chanturia, 2008, Kurkov and Kotova, 2007)."

Jan 1, 2018

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By Gerald W. Elger

Research at the Albany Metallurgy Research Center has shown that high-purity rutile can be produced from relatively low-grade ilmenite obtained from a massive rock deposit. Ilmenite is first smelted in an electric-arc furnace to separate the iron and produce a slag enriched in titanium dioxide. Titania slag mixed with a phosphate flux is then oxidized to synthesize rutile and form a phosphate-glass matrix which contains the impurities. Attrition scrubbing the treated slag in dilute solutions of phosphoric or sulfuric acid liberates the rutile, which is concentrated by physical methods. Tests show that synthesized rutile containing 95 to 97 pct titania responds to chlorination at the same rate as natural rutile.

Jan 1, 1973

By John J. Moore

This paper discusses the application of a video technique to construct stability diagrams for the combustion synthesis of ceramic-metal composites. Several model exothermic combustion synthesis reactions have been used to investigate the effect of the reaction parameters, eg. stoichiometry, green density, etc, on the stability of the propagating combustion reaction front and subsequent product morphology. The effect of varying the reactants and their stoichiometry to provide a range of reactant and product species ie. solids, liquids and gases, in the synthesis of both dense and expanded (foamed) ceramic and ceramic-metal composites was also investigated with respect to their corresponding combustion front stabilities.

Jan 1, 1993

By E. O. Chisholm

Synopsis The colour changes effected in a solution of dithizone by trace amounts of copper, lead, and zinc mineralization provide a sensitive field test for these metals. The method has been used with success by the United States Geological Survey to trace zinc orebodies under residual soils. The dithizone test is used here on samples of non-residual soil overlying a gold-bearing zone in which the gold is associated with disseminated sphalerite, galena, and chalco-pyrite. A gold-bearing zone was successfully traced under overburden ranging from a few inches to five feet in depth by means of this method. The method may prove useful in guiding preliminary trenching through light overburden, by outlining the extent of copper, lead, and zinc mineralization. Introduction The dithizone test affords a rapid, simple, and delicate test for the presence of zinc in soil and water and is suitable for use under field conditions. It has recently been used with success by the United States Geological Survey to outline a zinc-rich area in the residual soil over a primary zinc deposit in Tennessee. The purpose of the present study was to ascertain whether the method could be used to trace a gold-bearing zone, containing associated zinc mineralization, under shallow, non-residual, glacial overburden. The results obtained indicate that the method can be used to guide preliminary trenching in overburden up to six feet in depth. Tests made of the water near lake-shore outcrops also indicate that favourable prospecting zones may be located from the water, within five feet of the shore. It is felt that this simple field test should find a wider use in prospecting, because, under certain conditions, it can outline favourable zones and thereby reduce the amount of blind trenching necessary. The following pages describe the type of deposit tested, the method used, the .results obtained, and the difficulties encountered by a novice in the use of this chemical procedure. The author is indebted to the officials of Nor-Penn Mines, Limited, for their co-operation while the tests were being made; to the late Richard Bouska, Kenora prospector, for helpful suggestions; and to F. W. McCamus, University of Toronto undergraduate student, who ably assisted with the work.

Jan 1, 1950

By D. M. Xue, T. B. Li

"With the increase of human engineering activities, global climate change and active plate tectonics movement, the giant landslide frequently occurred in southwest China, which caused huge property and human losses. Besides, the potential landslides pose severely threaten to the construction and operation of airports, railways, highways and power stations etc. In order to provide accurate guidance for the landslide investigation, stability analysis and mitigation, the giant landslide is redefined according to landslide volume, depth of slip surface, complexity of landslide mechanisms, and degree of landslide mitigation difficulty, and classified with the typological classification approach based on the twofold attributes of landslide behavior including formation mechanisms and reactivation features. Finally, the threefold particularity of the giant landslide is also summarized, which enables a more effective landslide mitigation design.INTRODUCTIONWith the increase of anthropogenic activities, global climate change and active plate tectonics movement such as continual uplifting of Qinghai-Tibet plateau and strong earthquakes, the occurrence of giant landslides was in ascending trend in southwest China (Huang, 2009), which caused serious destruction, and greatly endangers such engineering construction from safety, time and economic aspects as airports, railways, highways, power stations, etc. Giant landslides have huge scale, complex formation/reactivation mechanisms and mechanical behavior. They may not be identified during the hazard investigation, but may be firstly initiated or reactivated due to the following engineering activities, heavy rainfall or strong earthquakes. Consequently, the landslide mitigation is inevitable and costly. However, it is difficult to control the deformation of giant landslide with lack of a correct understanding of genetic mechanisms (Marui, 2012; Zhang, 2000) and the excessive large sliding forces of the slide blocks calculated by the conventional limit equilibrium method. For instance, the failure of anchored pile wall for the No.102 giant ancient landslide (Zhu et al., 2012) and stabilization measures for the Sidi Rached viaduct landslide(Guemache et al., 2011); four rows of piles had not prevented the occurrence of the No.12 landslide in a high fill slope in the Panzhihua airport (Li et al., 2012)."

Jan 1, 2015