Search Documents

By Gergö Rimaszéki

Due the fast growing of pig iron and steel in the last years associate with some mineral resources changes (Hematite?Itabirite), has been checking the sinter feed degradation. The typical sinter feed (0.15;-6.3 mm) has become limited and the rapid growing production resulted in more and more fine ore (< 150 µm) availability in the market. The sinter plant operators are facing several new challenges since the mixing and granulation- and the sintering behavior of the fines containing mixtures often differs from the traditional sinter feed´s behavior. The utilization of fines in the sinter plants might increase the process water consumption required for the mixing and granulation process or even the solid fuel consumption, which effects the operational cost of the plant significantly. The current study presents an overview about Outotec´s laboratory facilities and competence regarding the mixing and granulation of fines in different equipments. The usage of high intensity mixers (HIM) – vertical and horizontal as well – showed to be the most effective, based in cold agglomeration tests in small scale, in case of fine ore handling. Permeability and particle size distribution curves are used to evaluate and demonstrate the efficiency of the different equipments. Outotec´s ”Know-How” with the different type of mixer and the modern laboratory facilities provide an excellent opportunities to optimize the mixing and granulation procedure and utilize up to 100 % pellet feed

Aug 17, 2017

By Steferson Ferreira de Oliveira

Desenvolvido nos últimos anos, o processo NDE, vem se tornando uma maneira promissora de usinar e nitretar simultânea a superfície de materiais metálicos. A Usinagem por Descargas Elétricas (EDM) é um processo de usinagem não convencional que tem grande potencial em aplicações de engenharia de superfície, ao melhorar a resistência superficial do material por meio de tratamentos termoquímicos, como por exemplo, a nitretação. Propriedades como: baixa densidade, boa resistência à tração (comparável à de muitos aços ligados) e excelente resistência à corrosão, possibilitam a aplicação do titânio e suas ligas nas indústrias aeroespacial, naval, química e automotiva e ainda no campo da medicina. Porém, raramente são usados como peças sujeitas ao deslizamento, devido a sua devido à sua baixa resistência aos mecanismos de desgaste abrasivo e adesivo e alto coeficiente de atrito. O tratamento termoquímico de nitretação pode solucionar esta restrição. Além de aumentar a resistência ao desgaste, o nitreto de titânio melhora a biocompatibilidade de suas ligas. O objetivo deste trabalho foi estudar a camada nitretada na liga de titânio Ti6Al4V por meio do processo de Nitretação por Descargas Elétricas (NDE), usando como fluído dielétrico solução de água deionizada e ureia granulada, como fonte de nitrogênio. Uma máquina de EDM por penetração foi utilizada no processo. Cobre e grafite foram utilizados como materiais dos eletrodos ferramenta. Foi avaliada a usinabilidade da liga Ti6Al4V com solução de água e ureia, relacionada aos parâmetros: taxa de remoção de material (TRM), taxa de desgaste (TD) e desgaste volumétrico relativo (DVR) para eletrodo de cobre e de grafite. Para caracterizar a camada nitretada foram realizadas microscopia óptica e medição de microdureza Vickers. A formação de nitretos na superfície foi avaliada por meio de difração de raio-x. Imagens metalográficas da seção transversal da superfície mostraram a formação da camada nitretada, devido ao ganho no valor da dureza. Os parâmetros relacionados à usinagem apresentaram valores que indicam um melhor desempenho quando se usa eletrodo ferramenta de cobre em relação à grafita. Nitretos de titânio foram observados no difratogramas da amostras nitretadas por NDE.

Oct 30, 2017

By Marshall T. E, Finfinger G. L

Gulf Coast domal salt mining operations have had sporadic encounters with methane gas emitted without any warning. In virtually all confirmed cases, the methane was localized in methane enriched zones. In a few cases large quantities of methane were expelled rapidly with salt outbursts, resulting in dangerous methane concentrations. Estimates of methane liberated by face blasts in methane-enriched areas is needed in determining how much air should be supplied to the face for proper dilution. A relationship between the gas content of salt samples collected from the face and the amount of methane liberated would be helpful in estimating how much methane will be produced by a face blast. Little is known about the layering or stratification of methane in large area-low velocity airways. This publication reports on three tests conducted by the Bureau of Mines which monitored the immediate return air of four faces during blasting. The test locations were in a methane gas-enriched section that had previously experienced two large outbursts and many smaller ones. A comparison was made between gas content values of face salt samples from the dissolution test and the gas liberation quantities. The characteristic movements of the methane in a large room with low air velocities were charted. This will help to better understand the factors involved in proper placement of methane sensors as a warning system.

Jan 1, 1988

By Lisa L. Van Loon, Neil R. Banerjee

Canada is a world leader in uranium exploration, but many deposits are located in remote regions making exploration targeting challenging. Novel approaches are needed to detect the presence of large-scale ore-forming systems and to vector toward mineralization. Boron is commonly used as a key pathfinder element associated with sandstone/unconformity-hosted and basement-hosted uranium deposits in the Athabasca Basin, but the genetic relationship remains uncertain. Alteration assemblages containing boron geochemical anomalies are commonly spatially-associated with – and possibly coeval with – uranium mineralization. Boron is commonly found in tourmaline minerals but in some portions of ore deposits the host mineral for the anomalous boron remains cryptic. Boron coordination chemistry within alteration haloes can better constrain boron host mineralogy, provide insight into the nature of the boron-uranium relationship, and thus has the potential to better constrain targets for exploration. Synchrotron-source X-ray absorption near-edge structure (XANES) spectroscopy is a direct, element-specific analysis that identifies boron coordinated in both trigonally- (BO3) and tetrahedrally-coordinated (BO4) forms. This makes XANES uniquely suited for identifying the geochemical hosts for boron that may be related to hydrothermal ore forming processes. XANES spectroscopy was conducted on whole-rock assay powders from uranium deposits across the Athabasca basin containing boron concentrations ranging from <10 ppm to >10,000 ppm. XANES directly identifies the relative amount of trigonally- (BO3) and tetrahedrally-coordinated (BO4) boron in these complex mineralogical mixtures. Our work suggests a link between boron and uranium that is likely related to the unique physiochemical characteristics of ore bearing fluids that may provide a unique vector to mineralization.

Jan 1, 2020

By Watters R

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to &apos;no&apos; or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By Filippo Verlezza

The 3-roll technology is a recognized process applied to SBQ production. The main aim of this paper is to show the latest developments on this technology including other equipment´s that also contributes for a better performance on SBQ coils production.

Jul 30, 2018

By Roberto Dalmaso, Vinícius Pesente Binotte, Luiz Alberto Moreira Andrade, Alan Amorim Margon, Davi Fiorese Bissoli

Esse trabalho tem como objetivo apresentar o equipamento de medição automática de placas desenvolvido pela ArcelorMittal Tubarão na área de condicionamento de placas. Anteriormente este processo era realizado de forma manual pelos inspetores. Esse equipamento visa facilitar a rotina de trabalho do inspetor e aumentar a qualidade da medição, assim como diminuir a dispersão dos dados eliminando a divergência nas medições das placas que se verificava entre diferentes operadores, além de possibilitar a criação de um histórico das medidas de toda placa. Para validação do equipamento o mesmo foi submetido a um sistema de analise de medição e teve seu resultado aprovado, no momento atual o mesmo se encontra em funcionamento para se realizar uma comparação estatística do seu desempenho em relação aos inspetores..

Oct 1, 2019

By PETER O. SANDVIK

The Cargill deposit, located 32 km south west of Kapuskasing, Ontario, was discovered by International Minerals and Chemical Corporation in 1975 and has been evaluated through an extensive program of drilling, chemical analyses, metallurgical tests and engineering and economic studies. The Cargill alkalic complex, comprising mainly carbonatite and pyroxenite-amphibolite rocks, was intruded into the rift system of the Kapuskasing magnetic-gravity high. Weathering and leaching under assumed temperate to cool climatic conditions plus faulting, shearing and/ or initial petrographic variations within the carbonatite developed a small, locally confined karst system. This resulted in a thick enriched leached carbonatite zone capped by troughs and sinks, and filled with a residuum of apatite, goethite, clay and other minerals. Residuum thickness ranges from nonexistent on ridges to 170 m in troughs and sinks. Apatite values are 5 to 15% in fresh carbonatite, 20 to 40% in leached carbonatite and 20 to 98% in residuum. A tentative open-pit mine designed for preliminary feasibility studies is estimated to contain 62.5 million tonnes averaging 19.6% P20 5.

Jan 1, 1984

By N. F. Faria, F. Monteiro, B. O. Taiwo, A. Palangio, D. Fonseca, J. Manuel

This paper explores the interpretation and application of Particle Size Distribution (PSD) curves in optimizing blast design and enhancing downstream operations. The study looks at important factors like D50, D80, fines content, and the uniformity index to show how PSD curves affect the efficiency of different mining processes. The first section of this paper discusses the impact of blast design parameters such as burden, spacing, and explosive energy on the resulting PSD, highlighting their significance for downstream operations like crushing, and material handling. The section concluded that proper alignment of PSD with downstream size classes, like primary crusher inlet sizes, among others, can result in substantial cost reductions and productivity gains. The second part presents a case study from dstgroup aggregate quarry in northern Portugal, utilizing fragmentation analysis to evaluate blast performance and promote continuous improvement. The section specifically examines the effect of stemming material size on blast fragmentation, comparing the impact of using aggregate with a D80 of 12.32 mm versus a D80 of 21.94 mm. The D80 value represents the particle size at which 80% of the stemming material is smaller, making it a critical parameter in evaluating the stemming's effectiveness in confining explosive energy. The drilling and blasting designs were meticulously planned using O-PitDev and O-PitSurface software to ensure accuracy in blast parameters and layout. To assess the fragmentation resulting from these different stemming material sizes, the study utilized WipFrag 4 software. The software allowed for precise measurement of particle size distribution after the blast, as well as a detailed comparison between the two stemming sizes. Results from the analysis indicate that using bigger-sized stemming material led to improved blast confinement, which in turn resulted in better fragmentation compared to the smaller-sized material. The reviewed blast videos demonstrate that the larger aggregate effectively contained the explosive energy within the borehole, thereby reducing premature venting and directing more energy towards breaking the surrounding rock mass. This led to finer fragmentation with D80 = 1240.1 mm, D50 = 685.9, and Dmax = 2580 mm, which is advantageous in downstream operations like crushing and milling. On the other hand, the smaller stemming material (D80 = 21.94 mm) did not confine the explosive energy as efficiently, resulting in coarser fragmentation (D80 = 1327.37 mm, D50 = 750.76, and Dmax = 2370 mm) and reduced overall blast efficiency. These findings highlight the significant influence of stemming material size on blast performance and fragmentation outcomes. 

May 4, 2025

By Paul O. Knorr

The Bureau of Ocean Energy Management (BOEM), a bureau within the U.S. Department of the Interior, has responsibility over both energy and non-energy mineral development on the United States Outer Continental Shelf (OCS) under the OCS Lands Act (“OCSLA”). BOEM’s Marine Minerals Program (MMP) manages federal offshore mineral deposits through non-competitive, negotiated agreements for sand and gravel (“sand”) used in coastal restoration efforts and the competitive leasing of critical and hard economic minerals (“critical minerals”). As the steward of OCS critical minerals, BOEM MMP is responsible for understanding where critical minerals are located, identifying and understanding their environments, managing activities that affect these resources, and implementing pertinent federal policies. Fulfilling these responsibilities involves the collection and analysis of environmental, geological, and geophysical data; supporting the science needed to understand the impacts of resourcerelated authorized activities on the biological, physical, and sociocultural environments; encouraging emerging technologies that can reduce the environmental impact of activities; and communicating with stakeholders to foster an understanding of existing federal regulations and potential needs to revise the legal framework. Four U.S. federal rules in the Code of Federal Regulations (CFR) currently inform MMP’s procedures: 30 CFR 580 (prospecting for minerals), 30 CFR 581 (leasing of minerals), 30 CFR 582 (operations in the OCS related to minerals), and 30 CFR 583 (negotiated noncompetitive agreements for sand). Other federal laws and regulations are also pertinent, particularly those supporting the National Environmental Policy Act, Endangered Species Act, National Historic Preservation Act, Marine Mammal Protection Act, Coastal Zone Management Act, Clean Air Act, Federal Water Pollution Control Act, and Magnuson Stevens Fishery Conservation and Management Act.

Feb 22, 2026

By Donggen Fang, Liu Xuan, Jilai Xue

SiO2 and Al2O3 in the metallurgical slag of nickel laterite ore have great recycling values. In this work, Si and Al were extracted from the slag in NaOH based molten salts through alkali roasting and water leaching process for preparing zeolite materials. The extraction ratio of SiO2 increases with increased temperature and appropriately prolonged time, and more than 80% SiO2 can be recycled from the slag after roasting at 550°C. Si and Al from the slag are in the filtered liquor for producing zeolite materials, while Mg, Ca, Fe and other impurities remain in the leached residues. Adding Na2CO3 into the alkalin-slag roasting process can reduce the amount of pure NaOH used with minor decrease in extraction ratio of SiO2, while make better separation of Ca to avoid it getting into the filtered liquor. Adding Al2O3 into the alkalin roasting process can replace part of more expensive NaAlO2 addition that is required for preparing zeotite material, which may bring out a minor decrease in extraction ratio of SiO2 due to formation of NaAlSiO 4 in the filtered residues. Quality X zeolite and 4A zeolite materials can be made from the starting liquor containing Si and Al recycled from the laterite nickel slag through alkali roasting and water leaching process.

Mar 1, 2018

By Aaron Nickoli, Brad Clark, Thomas Horan E. I. T.

The Canal Road Dip Slide is an active landslide located on South Pender Island, British Columbia. The effects of the fall 2021 atmospheric river prompted the British Columbia Ministry of Transportation and Infrastructure to initiate an emergency response project to realign Canal Road out of the active landslide zone for safe traffic passage. The work was tendered in a bidding process and included blasting and rock excavation work at the project site. Tetra Tech Canada Inc. was retained by the contractor to be their Blast and Vibration Specialist. The close proximities of an active landslide, a Canadian National Park, and other segments of construction posed stringent constraints to blasting. The governing constraints to blast design included a Peak Particle Velocity (PPV) limit of 3 mm/s (0.12 in/s) along the adjacent landslide centerline and a slide movement constraint. Sixteen blasts were executed throughout the scope of work to remove 2595 m3 (3394 yd3) of meta-sedimentary rock. Blast designs adhered to the constraints by utilizing up to quadruple decking in 50+ blast holes which lead to complex timing schemes. Several blasts were over 4 seconds in duration, with one at nearly 8 seconds. The landslide area was monitored with Shape Accel Arrays (SAA) throughout the scope of work that tracked geohazard slide movement during construction. The SAA data is presented, and the effect of blasting is discussed. Site specific parameters for PPV estimation were calculated and are presented. Collaboration and communication between the stakeholders allowed the project team to successfully overcome the technical challenges posed by the Canal Road Dip Slide.

Jan 26, 2026

By L. Escudero-Castejon, S. Sanchez-Segado, A. Jha, Y. Hara, S. Parirenyatwa

Oxidative alkali roasting of chromite is the state-of-the-art process for manufacturing chromium-containing chemicals, which involves dealing with serious environmental problems arising from handling Cr6+-containing wastes generated in this process. In this article a new method for the extraction of Cr2O3 from chromite ores is explained, based on the carbothermic reduction of concentrates in the presence of alkali investigated in the temperature range of 950–1050 °C. Under these conditions, the iron oxides present in the ore body are reduced to metallic iron and the resulting separation of chromium occurs by forming sodium chromite (NaCrO2). The reduced samples are magnetically separated for the recovery of an iron-rich fraction, and a non-magnetic fraction containing NaCrO2, MgO and other impurities. The further treatment of the non-magnetic fraction by leaching yields a Cr2O3-rich product of approximately 85% purity, with remaining alumina, alkali and magnesia. The main advantage of the process is that, under reducing atmosphere and subsequent leaching conditions, the oxidation of Cr3+ to Cr6+ is completely avoided; thereby decreasing the risk of land, air and water pollution.

Mar 1, 2017

By Francisco J. Sotillo

Using new ecological-natural-organic depressant for gangue and pyrite with antibacterial properties (control of acid mine drainage) with new improved xanthate collectors using rheology additive not chemical reacting with xanthate resulted in better sulfide flotation. Rougher-scavenger lead flotation tests were conducted increasing the concentrate grade from 7.07% Pb to 13.44% Pb, enhancing selectivity. Lead recovery increased from 64.08% to 79.38% and 80.40% using only the new depressant, and improved xanthate Z-11 and Z-4, respectively. The results demonstrated that the new depressant was selective and efficient, and the new improved xanthates stronger more selective collectors.

Feb 22, 2026

By Duclerc Fernandes Parra, Ademar B. Lugão, Nilton Lincopan, Fernanda Esposito, Vijaya Rangari

Polymeric hydrogels are natural or synthetic systems, which have gained interest due to their high biocompatibility with soft tissues. These types of hydrogels have been used for wound dressing as a drug delivery system. Here in this study the polymeric hydrogels based wound healing systems were prepared using poly (N-vinyl-2-pyrrolidone) (PVP), poly (ethylene glycol) (PEG), agar and neomycin drug followed by gamma irradiation to promote crosslinking and sterilization. The influence of irradiation process with 25 kGy dose was investigated. The gel fraction and maximum swelling were estimated using physicochemical methods and found about 95% gel fraction and 1100% swelling after 8 h of immersion. Neomycin released from hydrogel was carried out by Liquid Chromatography-Mass Spectrometry method and the drug concentration remained constant for 48 h. Hydrogel/neomycin exhibited antibacterial effects against Staphylococcus aureus. With these results, it can be inferred that hydrogel/neomycin is a suitable candidate for wound dressing.

Mar 1, 2018

By Patricio Vergara Lara, Jorman Barrera

The selection of the production level elevation is one of the most critical strategic decisions faced by large-scale block or panel caving projects. This elevation largely affects project timelines, capital expenditures, resource recovery, and may even constrain the mine’s maximum production capacity. Over the years, many computational tools have been developed to assist in this decision, most of them based on the same principle of maximizing the project value given its production level elevation. However, for large and inclined deposits, or those extending significantly in the vertical dimension and where extraction cannot be achieved from a single level, traditional selection techniques involving multiple production horizons often lead to suboptimal results. This paper proposes a methodology ensuring that the selection of production level elevations in a multiple horizons (“lifts”) case is globally optimized. Input parameters include economic and cost variables, maximum extractable column height, and deepening costs. The methodology is demonstrated through a real case study to illustrate its potential impact on project value.

Feb 22, 2026

By Seth Robertson

Instrumented static load testing is an effective means for assessing load-transfer characteristics of augered cast‑in‑place piles under static axial load. Strain gauges are typically instrumented on the steel reinforcement at specific locations along the pile&rsquo;s embedded length for determining geotechnical resisting forces in side-shear and end-bearing. Conversion of strain to internal force at each gauge level can be complicated, requiring critical assessment of the pile properties and potential strain-dependent behavior. Current codes and standards provide recommendations for approximating these necessary pile properties, although these methods may not routinely yield realistic interpretation of measured strains. Non-linear rigidity may be exhibited over a static load test duration and there remains limited published methods for determining load-distribution characteristic under these conditions. Through measuring embedded strain and uniaxial stress simultaneously, the pile&rsquo;s strain-dependent rigidity can be directly determined, thus minimizing uncertainty in the analytical process. While not commonly implemented in standard load test practices, stressmeters have been installed adjacent to strain gauges for this reason. A case study is presented where stressmeters were specially adapted for installation on augered cast-in-place piles on a bi‑directional static load test program. Based solely on the measured strains, it was realized that a non-linear rigidity would be required for properly converting strains to internal forces. The uniaxial stresses determined from the stressmeter measurements provided valuable insight in the pile material response to applied loads, ultimately reducing to a non-linear piecewise function of rigidity versus strain. Derivation of this non-linear piecewise function and methodology for computing internal forces are addressed. Comparisons of the non‑linear rigidity function to alternative rigidity (linear and non-linear) determination methods are presented. Recommendations for improving instrumented static load tests are summarized, primarily focusing on prospects and interpretation of embedded stressmeter measurements in top-down and bi‑directional static load tests.

Oct 7, 2024

By Erich Steinlechner, Freddy Lopez, Guido Maier

Due to the high damage potential that a possible flood event has for the densely populated areas along the 26 km-long “International Stream” of the alpine Rhine, the discharge capacity needs to be expanded from the current 3100 m³/s (100-year flood) to 4300 m3/s (300-year flood), in line with the requirements of the Swiss-Austrian project RHESI – Flood Control for the Rhine Valley. In this context, the existing 255m-long Rhine Bridge connecting the Austrian towns of Fussach and Hard is no longer able to ensure the primary framework conditions for flood protection and needed to be replaced by a new structure. The new Rhine Bridge Fussach-Hard, a state-of-the-art steel composite bridge with a separated rope construction, was designed to meet the new requirements for flood protection as well as to satisfy the increasing volume of traffic. The extremely unfavorable subsoil conditions, consisting of shallow, very soft to soft plastic lacustrine clay deposits, required a deep foundation solution for the substructure (abutments and piers). Due to the high flood risk, the construction of the substructure could only be carried out during a period of low water discharge (winter), resulting in a very tight construction schedule (winter half-year 2020/2021). For the deep foundation of the substructure, several options were evaluated. Finally, a solution consisting of pile grillages, executed with ductile cast-iron driven piles (320 mm of diameter), was adopted for the project. The fast, safe and simple execution of the piles allowed for the successful erection of the substructure within the limited available time frame. The completion of this construction stage was critical for the further phases. After a construction time of only 28 months, the Rhine Bridge Fussach-Hard was officially opened for traffic on November 18, 2022. The following technical paper presents an overview of the adopted deep foundation solution, focusing mainly on the design and execution of the piled foundation. Furthermore, additional topics such as the sustainability of the adopted solution and possible optimization measures will be discussed.

Oct 31, 2023

By Tony Sangiuliano, Jason Weck, Ryan Regier, Alper Turan

Cast-in-place concrete piles socketed in rock are a commonly used foundation solution in the province of Ontario. Although cast-in-place concrete piles are common, limited pile load testing has been undertaken on these foundations to confirm shaft friction (side shear) and end bearing parameters. Particularly, the large diameter piles bearing on rock makes conventional pile loads tests impractical and costly due to large capacities that need to be mobilized during testing. Performance of piles loads test come with the advantage of confirming the assumed geotechnical design parameters and permitting the use the larger strength reduction factor as per LRFD design. This paper presents the preparation, execution, and result interpretation of a pile load test carried out on two Cast-in-place concrete piles with diameters of 1.5m and 1.8m for Garden City Skyway Project in the City of St Catherines Ontario, Canada. The 1.5m and 1.8m diameter test piles were socketed 4m and 6m into shale bedrock. Osterberg cells were used in both load tests to provide end bearing and shaft friction parameters for the shale bedrock as well as overlying layers of till and soft clay. The results of the load test provided valuable insight into the load settlement performance exhibited by these piles. The results are also compared with the analytical estimates of the pile capacities presented in geotechnical report as well as the results of a number of other analytical socket design approaches.

Oct 7, 2024

By Samar Saad, Mazen Adib, Farid Motamed, Medji Sama

Abstract Deep foundations were necessary to support bridges, retaining walls, and other structures at the I405 Improvement Project in Orange County, California. The ground properties and stratigraphy were primarily investigated using cone penetration tests (CPTs), with confirmatory boreholes and laboratory tests. A CPT-based design calculation method, the LCPC-CPT by Bustamante and Gianeselli, was followed to predict the axial geotechnical resistance. To justify a resistance factor of 0.7, extensive Pile Driving Analyzer (PDA) measurements were performed to allow calculation of the driving resistance using Case Pile Wave Analysis Program (CAPWAP). The piles included open ended 24-inch diameter steel pipe piles, 14, 16, and 18 inch H Piles, and 14-inch square Precast Prestressed Concrete Piles. The paper presents the subsurface conditions and ground properties from the CPTs and the predicted versus CAPWAP axial capacities for the various types of piles. The paper will also present challenges encountered and opportunities from lessons learned. It was observed that, in general, the CAPWAP axial capacities were in acceptable agreement with the LCPC-CPT predictions, although capacity incorporating full setup was not measured on all piles. Also, the correlations between LPCP-CPT predictions versus CAPWAP axial capacities depended on the type of pile.

Oct 7, 2024