Search Documents

By Douglas L. Scaggs

Over the past several years, pile foundations have grown to meet the demands of larger and heavier structures. As the foundations have grown, so has the need for larger and more robust piles to carry the increased loads. Seismic considerations have also required larger and tougher piles to withstand the added component of supporting structures during earthquakes. While H-piles, precast concrete piles, timber piles and small pipe piles have been the product of choice, many applications are now calling for much larger piling requiring larger equipment and presenting the contractor with new challenges. This paper is not intended to be a ?how to? guide as much as a discussion on the potential pitfalls a contractor should watch out for when considering a project where mega piles are required.

Jan 1, 2013

By Shoobridge PH

Operating difficulties during 1977 with the Imperial Smelting Furnace operated by Sulphide Corporation Pty. Limited at their Cockle Creek zinc-lead smelter were found to be caused by premature softening of sinter in the upper shaft of the furnace. This soft- ening was shown to be a consequence of raw materials and operating policies which led to unusually high levels of both lead and silica in a sinter of low basicity. A programme of softening tests and micro-examination of a range of sinters established that premature softening occurred when lead and silica increased to the point where a lead-calcium silicate with a low lime content became the major continuous phase in the sinter. This information was used to define a range of compositions which kept the softening temperature acceptably high for furnace operations.

Jan 1, 1978

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

By James D. Reilly

The time-worn adage "an ounce of prevention is worth a pound of cure" was never more applicable than when used in reference to coal mine safety. Many individuals have dedicated many hours to developing effective accident prevention programs, and much has been accomplished. Each production escalation, however, creates new hazards and safety problems which need special study and research. It is a never ending cyle. To study the progress of coal-mine safety is to raise memories of many individuals who have been dedicated to removing the hazards that have developed with increased productivity and deeper penetration into the earth for coal. Some vivid examples of this dedication are the works of the men who pioneered the use of the safety lamp and the use of rock dust in mining.

Jan 1, 1968

By W. H. Bassett

IN their paper on the directional properties in cold-rolled and annealed commercial bronze,1 Phillips and Samans suggest that cupronickel, under distinctly different treatments, shows both "45° ears" and "90° ears. " Fig. 1 shows the ears on some cupronickel cups made some 17 years ago for bullet jackets for small arms ammunition. In this case the material heated to 425° C. had "45° ears, while that annealed at 950° C. showed FIG. 1.-CUPRONICKEL, 0.032-in. GAGE, CAST WITH MAGNESIUM. ANNEALED AT TEMPERATURES INDICATED (DEGREES CENTIGRADE) AND CUPPED. long "90° ears" when drawn with the same tools. The method of cupping, the shape of cupping tools, etc., were found to have very little influence on the earing tendency, but the deeper the cup was drawn, the higher the ears would be.

Jan 1, 1932

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009

By Higuchi K

In this paper, the history of Japanese coal and gas outbursts is presented and circumstances and countermeasures at the time cf outbursts are summarized statistically. Then the present meth- ods for prevention used practically in Japan are introduced. From statistics, it was reconfirmed that Japanese coal and gas outbursts have occur- ed frequently in the district of geological disturbance, symptoms immediately before out- burst occurrence were the phenomena in connec- tion with failure of a coal seam and outbursts have occurred many times when the number of boreholes had not been sufficient to degas. One of the principal protective method adopted in Japan is the large diameter gas drainage boring which also posesses a stress relief effects. There is a tendency to make diameter of borehole larger to increase both stress relief and degassing effects.

Jan 1, 1986

By V. Oberholzer

The presence of fines (particles smaller than 6 mm in diameter) causes hydrodynamic problems in gasifiers and therefore it is of great importance to minimize the amount of fine coal in the feed. This serves as motivation for understanding coal?s breakage mechanisms, which could lead to the ability to predict the generation of fines. The aim of this project was to simulate the pulsating effect of the conveyor belt in order to investigate factors influencing the breakage. Results indicated that an increased initial particle size had an increasing effect in the amount of fines generated. Weathering had an insignificant effect on the breakage of coal. To conclude, a breakage model was developed to describe the rate of breakage out of the top size when a combination of two breakage modes is present.

Jan 1, 2009

By D. J. Carney, R. R. Burt, E. J. Whittenberger

Hardenability (multiplying) factors for carbon, mongonese, silicon, chromium, nickel, and molybdenum have been developed for hypereutectoid low-alloy steels in which bainite is the first subcritical transformation product. These factors permit the calculation of 95, 80, and 50 pct martensite hardenability from chemical composition when steels with spheroidized structures are quenched from 1475°, 1525°, and 1575°F. The strong contributions to hardenability of the less expensive elements, silicon and manganese, suggest their use to obtain additional hardenability in hypereutectoid low-alloy steels. DURING the past decade a number of investigators'"11 have carefully developed information which permits calculation of the hardenability of medium -carbon low-alloy steels from chemical composition and grain size. These data have been especially valuable in developing less costly low-alloy steel compositions with equivalent or Improved

Jan 1, 1957

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009

By Cocker J, Urosevic M

Seismic methods have become common for the detection of low-throw faults ahead of underground coal mining. Surface seismic methods cannot theoretically be used where dykes occur, because seismic waves transmit from the surface down to the seams, and reflect back to the surface. Consequently, where sub-vertical structure such as dykes occurs, the surface seismic method fails.The ability of seismic methods to image dykes depends on the geometry used, the dyke thickness and the seismic wave propagation mode in relation to dyke composition and internal structure. Surface seismic methods find it difficult to distinguish between faults/fractures and very thin dykes (1-2m in thickness) when the dyke's thickness is less than the seismic wavelength. Consequently, borehole seismic methods have to be used to detect the presence of such thin dykes.

Jan 1, 1998

When Matthew Flinders entered in his log `This land forms the South side of the large bight; and besides projecting beyond the coast line, and being a little higher than usual is remarkable for having some reddish cliffs in it, and deep water near the shore', he was commenting on the deposit of bauxite at a place now known as Weipa. This sighting took place on 9 November 1802, and probably represents the first direct entry in Australia acknowledging a potential mineral deposit. Flinders, of course, had no idea as to what he was looking at, nor did he land to determine its content. If he had, he probably would have had no idea of the substance, and even less knowledge of its use. Nothing further was done to this for about 150 years.

Jan 1, 1993

Comparatively recent Tasmanian legisla tion established a series of rigid control standards for environmental protection just as ma spectacular expansion of the mining industry was nearing completion. Upgrading existing protection to obtain the necessary licence to operate under these new regulations required further major works and involved a considerable outlay of non- productive capital at a time when escalating costs and falling metal prices were straining economic efficiencies to the limit. Late in 1974 a major environmental protection scheme was commissioned by the Electrolytic Zinc Company of Australasia Limited at Rosebery on the West Coast of Tasmania. This 4 million dollar project was specifically developed by the Company ahead of and to meet the new standards for control of total effluents discharged from its zinc-lead -copper-pyrites mine and concentrator.

Jan 1, 1977

By Larry G. Stolarczyk

This report deals with the creation of an efficient method to determine if command, control, communication and monitoring (3cm) equipment in coal, metal and non-metal mines is susceptible to Radio Frequency Interference (RFI) from the Medium Frequency (MF) radio communications system. A qualitative and quantitative RFT test plan was developed for in-mine and laboratory evaluation of the equipment. The laboratory testing was accomplished using the TEM Test Chamber. Detailed information on the Test Plan and the TEM Test Chamber is included. During in-mine testing of the MF System some underground equipment malfunctioned when the transmitter's radiating antenna was in close proximity. Electromagnetic Compatibility (EMC) testing was done on three levels; Component (circuit or box), subsystems and system. Nine tables are included which show the results of testing various equipment for RFI.

Jan 5, 1986

A paper describing the treatment of the Mary Kathleen uranium ores must necessarily be historical and confined mainly to a review of the four papers which have already appeared. Couche and Hartley (1958) described the development of the treatment process just prior to the commencement of operations in June, 1958. Harris, Boag and Hemingway (1961) described the treatment during the operations, and Wreford (1965) reviewed all aspects of the mine and mill, when operations were suspended in November, 1963. Harris and Steele ('1960 presented a paper especially describing the radiometric sorting operation. Some hitherto unpublished information is also presented in the paper to describe some of the peculiarities of the ore, indicate reasons for the adoption of the treatment flowsheet, and some interesting problems connected with this treatment.

Jan 1, 1968

In 1955 the annual production of steel at Australian Iron and Steel Pty. Ltd., Port Kembla was 1.2 million tonne and over the following two decades this had progressively increased to the present capacity of 5.4 million tonne per annum. This increase in productivity has also been accompanied by important developments in steelmaking technology and these are explained in the chronological order in which they have taken place. Reference is made to the use of oxygen in open hearth furnaces, the B.O.S. process, the Argon-Oxygen decarburisation process for stainless steel, vacuum degassing and continuous casting. When the vacuum degassing and continuous casting units are commissioned, the Port Kembla Works will have achieved a standard of steelmaking technology equal to any in the world.

Jan 1, 1976

By S. J. Schatzel, J. Cervik, A. A. Campoli

The cross-measure borehole technique is being studied by the Bureau of Mines as an alternative to the use of surface gob boreholes as a means of controlling methane in gobs during longwall mining. Small-diameter holes are drilled from underground locations into strata overlying the mined coalbed. When the roof strata are fractured by the mining opera- tion, a partial vacuum applied to the boreholes draws the methane out of the fractured strata and prevents it from entering the mine ventilation system. Tests in the Upper Kittanning Coalbed showed that 50 pct of the methane produced by the longwall mining operation was captured by the cross-measure boreholes. Borehole inclination and penetration into the gob are two important borehole parameters that affect the performance of the cross-measure borehole system.

Jan 1, 1983

An enormous capital outlay is required to bring a new deep level (¦ 4 000 m deep) Witwatersrand gold mine into production. In addition, future mining methods must cater for rapidly rising working costs of which labour costs make up the largest portion. South African mining engineers are therefore being forced to challenge accepted design and valuation principles when planning these high risk ventures. New mining methods must be sought to satisfy the ever increasing need for productivity improvement. The technological problems posed by such changes cover a wide range of disciplines. Aspects of shaft design and configuration, besides being examined in the light of productivity, must also consider the rock mechanics implications at depth. Mining methods must anticipate and prepare for extremely hostile conditions due to seis- micity and virgin rock temperatures.

Jan 1, 1986

By Brown N. R

This paper attempts to highlight some of the problems encountered in the economic exploitation of the deeper coal seams by opencast mining methods. The major cost elements of three methods of overburden removal are examined in relation to the overall cost of winning coal from deeper-lying coal seams. The three overburden removal methods examined are dragline stripping and two systems combining dragline stripping with shovels and trucks at varying depths of overburden. A dragline is, undoubtedly, the most cost effective system of overburden removal for depths of up to 30 metres but it is suggested that, when dealing with incremental overburden depths in excess of 30 metres, engineers should consider carefully the possibility of using a shovel and truck operation, or other system, to augment the use of a dragline.

Jan 1, 1986

A shrinkage stope is an overhand stope in which the broken ore accumulates until the stope is completed to, or near, the level above. As broken ore generally occupies at least 60 per cent. more space than ore in place, about a third of this must be drawn out as the stope advances to leave a working space under the back. The ore remaining supports the miners and gives temporary support to walls, and is all withdrawn when the stope is finished. The shrinkage-stope method is applicable to steep-dipping deposits of strong ore with strong walls. It may be applied to narrow or wide veins, and is simple and cheap. Five examples, which include important and varied types of deposits, are given: namely, Kennecott, Homestake, Jarbidge district, Mogollon district, and Cripple Creek district.

Jan 1, 1925