Search Documents

By Michael Li

Unsaturated flow and solute transport were studied in three large columns measuring 1.5 m diameter x 2 m height, loaded with up to 3.7 t of oxidised waste rock, which was excavated from the Stratmat pile at Heath Steele Division, Noranda Inc. and contained elevated concentrations of zinc in the pore water. The bottom of each column was partitioned into 37 squares, each of which was drained independently. Following rain simulations at the top of the rock bed, the drainage in each drain port was monitored for volume and physicochemical parameters at pre-determined intervals. This paper describes some of the observations resulting from the experiments. The main conclusion of the study is that unsaturated flows in waste rock are heterogeneous, and flow channelling is ubiquitous. The results imply that the transport of solutes from oxidised waste rock to its toe drainage is subject to various controlling mechanisms, including geochemical equilibrium control and successive pore water dilution control.

Jan 1, 2000

By Bernard J. Steblay

Millions of mechanical anchor roof bolts are used each year for mine structural support. The benefit of this bolting depends on a number of factors including rock density, bolt length, in situ stresses, time elapsed between mining and installation, rock properties, bolt patterns, and tension (Lang, et al., 1979). Installation tension is a major determinant of support quality. Postinstallation tensions indicate both the usefulness of the individual bolts and the behavior of the reinforced rock structure. The importance of short- and long-term bolt tension measurements is well recognized, and such measurements are required by regulations (Fed. M/NM Nine Safety and Health Reg.). These regulations also take into account the difficulty of practical tension measurements. Only a statistical sample of the bolts installed is required to be measured using current torque wrench technology. Drawbacks to this practice are that the anchorage is disturbed and perhaps weakened, accuracy is limited by friction to about 30% (Lang, et al, 1979, and Barry, et al., 1956), and the procedure is relatively time intensive.

Jan 1, 1984

By James R. Grage

The lead deposits of Missouri may be divided into three districts, the southwest, middle, and southeast. As too much time would be required to devote a detailed account to each district, only a description of the modes of occurrence of the lead ores in the southeast district will be given. The lead mining region proper of Southeast Missouri is embraced in an area of about twenty-five miles in width by about one hundred in length. The country embraced in this district is very broken, and traversed by ridges from one hundred to three hundred feet; in height, with an occasional knob rising higher. Porphyry forms almost the entire substructure of the region, with here and there outcrops of granite. The crystalline rocks were eroded into ridges and valleys before the deposition of the limestone took place. These porphyries are older than the Silurian limestones, and " belong (according to Pumpelly) to the Archaean (Azoic) formation, of which they may be the youngest member in Missouri. They are the near equivalents, in point of age, to the great iron-bearing rocks of Lake Superior, New Jersey, and Sweden."

By Franz Wever

The importance of the Widmanstätten structure to structure theory in metallography has been recognized by many writers.l It is a structure produced by the precipitation of a, new phase from a solid solution upon cooling as a result of changing solid solubility, and displays a characteristic appearance indicating a crystallographic relationship between the new phase and the original solid solution (Fig. 1). First discovered in 1808 by Alois de Widmanstätten2, the structure has been traced by analogy through many alloy systems. Particularly is this true of the steels. Sorby's classic work3 on the microstructure of iron and steel was in essence an attempt to explain the origin of this characteristic structure in meteoric iron. He observed in a Ressemer steel and in a cast-steel ingot structures which we now recognize as typical Widmanstatten figures.4 Osmond Observed structures in a steel ingot analog-ous to those found in meteorites. Arnold and Mc William6 obtained (and recognized) a

Jan 1, 1931

By Fathi Habashi

METALS COMMONLY leached may come from one of the following sources: 1) Occurring in nature in the native state, e.g., gold, silver, platinum metals, copper. 2) Produced as by-product of a metallurgical process, e.g., gold, silver, platinum metals, selenium. 3) Produced by reduction of an oxide ore, e.g., copper, nickel. GOLD AND SILVER Cyanidation According to Mellor (1923) the alchemists of the eighteenth century knew that gold was soluble in aqueous solution of potassium cyanide, and the early jewelers probably utilized this fact in gilding. He also mentions that Scheele in 1783 and later Bagration in 1843 noted the solvent action of aqueous solutions of alkali cyanides on gold. Yet it was not until 1887 that the value of this observation was recognized, when MacArthur and Forrest (1887) made use of it in leaching gold from its ores. Since then, the process has spread to every gold and silver mining district in the world.

Jan 1, 1970

By Robert Mehl

THE importance of the Widmanstätten structure to structure theory in metallography has been recognized by many writers.1 It is a structure produced by the precipitation of a new phase from a solid solution upon cooling as a result of changing solid solubility, and displays a characteristic appearance indicating a crystallographic relationship between the new phase and the original solid solution (Fig. 1). First discovered in 1808 by Alois de Widmanstätten2, the structure has been traced by analogy through many alloy systems. Particularly is this true of the steels. Sorby's classic work3 on the microstructure of iron and steel was in essence an attempt to explain the origin of this characteristic structure in meteoric iron. He observed in a Bessemer steel and in a cast-steel ingot structures which we now recognize as typical Widmanstätten figures.4 Osmond5 observed structures in a steel ingot analogous to those found in meteorites. Arnold and McWilliams6 obtained (and recognized) a

Jan 1, 1930

The BLEG (Bulk Leach Extractable Gold) technique is a semiquantitative measure of cyanide extractable gold contained in a sample. A 5kg sample is leached in cyanide solution for 24 hours and gold is precipitated out of the pregnant solution using zinc and assayed by AAS. The detection limit is reported as ppb (parts per billion). Telfer is located 1300km north north-east from Perth in the Great Sandy Desert. The climate is one of hot summers with irregular rainfall and mild winters. A large portion of the area is covered by aeolian sand and seif dunes with poorly developed drainage, rare outcrop; topographic relief is a maximum of 96m. Poor outcrop and poorly developed drainage render conventional stream sediment sampling and soil geochemistry inadequate. Therefore a technique providing a minimum number of samples with maximum accuracy and sensitivity was needed. Consequently BLEG orientation surveys were conducted over the Telfer Mine area in 1983, 1984 and 1985.

Jan 1, 1988

By Robert H. Merrill

Several investigators have obtained solutions for the concentration of stress around circular, ovaloidal, elliptical, and rectangular holes in an elastic, isotropic, semiinfinite plate subjected to uniaxial and biaxial stress. These solutions are used to evaluate the changes in stress around openings immediately under the undercut normally used in conventional block caving operations. The evaluations are based on the assumption that a horizontal undercut removes most of the vertical component of a biaxial stress field. The location and magnitude of the significant changes in stress concentration around the opening are computed. Conditions under which the assumptions used in the evaluations may or may not be consistent with conditions around block caving mines are discussed, and examples of preferred opening shapes for a biaxial (hydrostatic) stress field are shown. This report is a summary of one phase of an investigation to establish design methods for the size and shape of mine openings used in block caving mining methods .

Jan 1, 1962

By V. T. McLemore

The Steeple Rock district is a major epithermal .gold-silver district in New Mexico that exhibits district zoning. Five types of ore deposits occur in the district. The base-metal veins (with Au and Ag) form the center of the district and occur along the Carlisle fault. The gold-silver veins occur along northwest-trending faults outward from the base-metal veins. The margins of the district are formed by copper-silver, fluorite, and manganese veins. In addition, areas of older acid-sulfate alteration occur throughout the district and also exhibit zoning: massive silica/chert zone (inner), silicified zone, and clay zone (outer). This alteration overlies regional; alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow but older epithermal hot springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1994

By A. D. Hughes

A relatively small area in Malaya, about 200 miles long by 40 miles wide, is the most important source of tin in the world. Some tin is recovered in other parts of the peninsula. Of the tin mined, 98 pct is recovered from alluvial deposits. From 1935 to 1941 the average annual world production of tin was 190,000 tons. The average annual production from Malaya during the same period was 62,000 tons or about one third of the total. Other producing countries, in order of importance, were the Netherlands East Indies 34,000 tons, Bolivia 30,000, Belgian Congo, Nigeria, Siam, Burma, China, and a few others with smaller amounts. The serious shortage of tin during the war period was due to the fact that the Japanese were occupying Malaya, Netherlands East Indies, Siam, Burma, and China which, together, formerly were producing 65 pct of the world supply.

Jan 1, 1949

By D. B. Dreisinger, A. A. Gunaratnam

A pressure oxidation (POX)-hot cure (HC)-lime boil (LB) process is used in industry to recover silver from refractory gold sulfide ores containing minerals such as pyrite and arsenopyrite. Pressure oxidation is used to oxidize minerals and liberate occluded gold particles. As such, iron goes into solution and under acidic and high temperature conditions often precipitates as basic iron sulfate (BFS). BFS consumes excess lime during neutralization prior to cyanidation. Therefore, a hot cure stage is required to re-dissolve BFS back into solution. BFS re-dissolution consumes acid and produces ferric sulfate. In the presence of silver, these conditions favor the slow formation of silver jarosite. Silver jarosite is refractory to cyanidation, and must be broken down prior to cyanidation. This is done in the lime boil to produce a cyanide-soluble silver hydroxide. A study was conducted to investigate parameters that affect the precipitates that form in each stage of the POX-HC-LB process.

Jan 1, 2017

By G. T. Horne, P. J. Wray, S. Kinoshita

CONSIDERABLE evidence exists for a strengthening mechanism operative at intermediate temperatures in bee metals containing interstitial solute atoms. The strengthening is indicated by a maximum in the ultimate tensile strength1 as well as the fatigue

Jan 1, 1965

By H. Mulder, M. C. Bekker

The principal objective of this investigation was to conduct a thorough literature review on the status of project readiness mechanisms, tools, techniques, and frameworks for mining projects. The review aimed at identifying common readiness evaluation criteria as well as potential shortcomings that prevent the establishment of a generalizable project readiness index. The literature review included a general overview of capital project performances and the importance of project readiness assessments to improve project delivery success. The study then progressed towards literature involving mining projects and how this differs from infrastructure and industrial project assessments. The paper concludes by summarizing the current state of mining project readiness assessments, the unique and differentiating factors to be considered, and suggests recommendations towards the development of generalizable readiness assessment criteria for mining projects.

Sep 1, 2022

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By Clayton R. Morlock

Airblasts have been monitored at four coal strip mines and at a limestone quarry. Thirty-seven production blasts have been monitored with three seismographs, resulting in one hundred and eleven complete air pressure records. Instrumentation selection use is described. Data analysis includes an assessment of the predictability of peak overpressures by means of the cube root scaled distance law. It is found that predictability for the cases studied here is not good. An extensive discussion of possible explanations is included. A detailed analysis of the frequency content of the observed airblasts, of considerable importance in evaluating potential annoyance problems, has been made for all records. A computer program has been written to simulate airblasts induced by multiple-hole blasts. A series of small experimental blasts have been detonated and monitored in order to allow an assessment of the program. It is clear that airblasts, especially when induced by very small charges and monitored at very close distances, are highly sensitive to detonation times. Retrofitting of airblast records occasionally was possible, but considerably improved field work is required to validate or refute the computer model.

Jan 1, 1983

By Gary M. Larwood

A study was conducted to determine the amount of transportation equipment required to move 1.2 billion tons of coal in 1985. The Federal Bureau of Mines has investigated a majority of the various practices associated with coal transportation and has gathered information on the regional origin-destination patterns, methods of movement, equipment stocks, rate structures, and operational capacities of the most important modes of coal haulage currently in use. Models employing this information were developed to establish the origin-destination pattern for 1985 coal shipments, estimate practical tonnage capacities for selected coal hauling rivers, develop modal shares for both unconstrained (by river capacity) and constrained cases, and present a range of coal transportation equipment requirements for given sets of constraints. Projected transportation shares for rail ranged from 63.7 to 72.3 percent, and for river, from 8.8 to 16.4 percent. Other coal transportation modes (truck, conveyor, Great Lakes, and tidewater) are expected to retain their historic shares of coal traffic. Equipment estimates were made for 1985 rail and water transportation based on 1973 average and best practice. Average practice estimates ranged from 675,000 to 710,000 hopper cars (100-ton) and 3,100 to 5,940 barges (1,400-ton equivalent). Best practice estimates ranged from 126,000 to 142,000 hopper cars and 1,750 to 3,450 barges. Full implementation of 1973 best practice by 1985 is unlikely.

Jan 1, 1976

By J. C. Uy, A. A. Burr

IN the primary solid solutions of zirconium-base alloys, there is a striking regularity of the effect of solute valence on the stabilization of the allotropic phases.1 The valences derived by pauling2 are for elements as they are bonded in the solid metallic state. Effects of variations in isotopes, alloying elements, and allotropes on their valences are difficult to determine and such data are presently unavailable. Pauling's values are somewhat empirical and approximate, but if some definite correlations can be found between those values and experimental observations, this will lend support to the tacit assumption that the possible variations in valence mentioned above are small. Pauling has amassed a large amount of evidence of such correlations. It is the purpose of this technical note to show another application of the Pauling valences and to offer a possible explanation for this observation. The relationship between the Pauling metallic valence of the solute and the stabilization of allotropic phases in zirconium is shown in Table I, which has been compiled from available data in the literature3 plus the results of work done at Rens-selaer Polvtechnic Institute.' The chemical valences are included for comparison. It can be seen that a solute whose metallic valence is lower than that of the solvent tends to stabilize the a phase while one whose metallic valence is higher than that of the solvent tends to stabilize the 0 phase. It should be noted that, inasmuch as the Pauling valences are periodic with atomic number, this is tantamount to saying that the elements in groups I-A, 11-A, III-A, III-B, IV-B, V-B, and VI-B are a stabilizers while those in groups IV-A, V-A, VI-A, VII-A, VIII-A, I-B, and 11-B are ß stabilizers. The chemical valences do not show such consistency. Although the zirconium-rich end of the Zr-Au diagram is not available, it call be expected that gold, having a metallic valence of 5.56, would stabilize the ß phase. At absolute zero, the Fermi energy level is the criterion of equilibrium, i.e., the structure having the lower Fermi level will be more stable. Conse- quently, allotropic transformation occurs in a metal when thermal excitation raises the Fermi level to a point at which the atoms can be better accomodated by a different structure which yields a lower Fermi level.4-6 Thus in allotropic transformation, a change in structure occurs as a result of the change in the energies of the bonding electrons. Since the Pauling valence is the number of bonding electrons per atom, and these are the only electrons whose energies are affected by thermal excitation,* it can be inferred that the introduction of a solute which has a higher Pauling valence than that of the solvent raises the initial Fermi level; consequently, the transformation temperature is lowered. The converse is also true. The fact that at the transformation temperatures this statement is still fairly valid implies that the contribution due to the difference in specific heat terms of the two allotropes is comparatively small.

Jan 1, 1962

By J. C. Zachariades, D. M. Fraser

The leaching of pyrolusite in acidic ferous sulphate solution was studied so that the important factors governing the kinetics of the reaction could be determined. The reaction is very rapid, and was monitored by continuous measurement and logging of the redox potential in solution by use of a microcomputer. The relationship between redox potential and manganese extraction was established empiricaly for each set of conditions by the use of a technique in which a calibration run was conducted in paralel with each leaching run. The study involved a number of batch leaching runs, and demonstrated that, of the variables investigated, only the initial ferous ion concentration and the reaction temperature afect the rate of manganese extraction. The final extraction did not vary. The reaction was modeled from the results by use of the shrinking-core model and Britan's activation-energy model. The later was found to provide a significantly better fit to the data.

Jan 1, 1991

By A. F. Taggart, Nathaniel Arbiter

The chemical reaction occurring in collection of nonmetallic minerals with amine-type collectors was early postulated by students of flotation phenomena to be metathesis between the mineral and the collector, involving exchange between the amine-bearing (aminium) ion and the cation of the mineral, and formation at the mineral surface of an oriented film of the amine salt of the mineral anion. Qualitative evidence of exchange has been obtained on several occasions at Columbia. Thus 1000 C.C. of a solution containing 495 mg of laurylamine hydrochloride was shaken 17 min. with 100 grams of barite and ground in a porcelain mill to pass a 200-mesh screen; the mixture was then set aside for 48 hr. Filtrate therefrom analyzed 476 mg. per liter of laurylamine hydrochloride. There was no substantial loss of chloride ion (78.4 mg. per liter in the original; 74 in the filtrate). No successful analyses were concluded for barium ion. Earlier, confessedly rough work with scheelite indicated a solution gain in Ca++ equivalent to about one-half the aminium ion lost. Real quantitative roof of the exchange, in the form of an established stoichiometric balance, is unknown to the authors. The data of the present paper, however, obtained from experiments designed on the basis of the exchange hypothesis, constitute strong evidence of its truth, and at the same time point the way to economic utilization of the expensive nitrogen-bearing collectors in concentration of the low-priced nonmetallic minerals. The basic postulate underlying the experiments performed was that, if the collecting reaction is of the type R+ + Y- + MX = RX + M+ + Y- where R = aminium ion, Y = the anion of the amine salt, and M and X are, respectively, the cation and anion of the mineral, the reaction should obey qualitatively the implications of the mass-action and solubility-product laws. This is to say that coating and collection should be aided by the addition to the solution of either ion (R+ or X-) of the collector-coating compound, and hindered by the addition of either of the ions M+ or y-. Experimental work comprised determination of (,) the relative solubilities of the laurylammonium salts of a variety of nonmetallic-mineral anions; and (21 the contact angles' of various minerals in solutions containing different concentrations of the postulated controlling ions. Semiquantitative flotation tests were run With barite as checks on the diagnostic character of the contact angles. The amine

Jan 1, 1947

By Nathaniel Arbiter, A. F. Taggart

The chemical reaction occurring in collection of nonmetallic minerals with amine-type collectors was early postulated by students of flotation phenomena to be metathesis between the mineral and the collector, involving exchange between the amine-bearing (aminium) ion and the cation of the mineral, and formation at the mineral surface of an oriented film of the amine salt of the mineral anion. Qualitative evidence of exchange has been obtained on several occasions at Columbia. Thus 1000 C.C. of a solution containing 495 mg of laurylamine hydrochloride was shaken 17 min. with 100 grams of barite and ground in a porcelain mill to pass a 200-mesh screen; the mixture was then set aside for 48 hr. Filtrate therefrom analyzed 476 mg. per liter of laurylamine hydrochloride. There was no substantial loss of chloride ion (78.4 mg. per liter in the original; 74 in the filtrate). No successful analyses were concluded for barium ion. Earlier, confessedly rough work with scheelite indicated a solution gain in Ca++ equivalent to about one-half the aminium ion lost. Real quantitative roof of the exchange, in the form of an established stoichiometric balance, is unknown to the authors. The data of the present paper, however, obtained from experiments designed on the basis of the exchange hypothesis, constitute strong evidence of its truth, and at the same time point the way to economic utilization of the expensive nitrogen-bearing collectors in concentration of the low-priced nonmetallic minerals. The basic postulate underlying the experiments performed was that, if the collecting reaction is of the type R+ + Y- + MX = RX + M+ + Y- where R = aminium ion, Y = the anion of the amine salt, and M and X are, respectively, the cation and anion of the mineral, the reaction should obey qualitatively the implications of the mass-action and solubility-product laws. This is to say that coating and collection should be aided by the addition to the solution of either ion (R+ or X-) of the collector-coating compound, and hindered by the addition of either of the ions M+ or y-. Experimental work comprised determination of (,) the relative solubilities of the laurylammonium salts of a variety of nonmetallic-mineral anions; and (21 the contact angles' of various minerals in solutions containing different concentrations of the postulated controlling ions. Semiquantitative flotation tests were run With barite as checks on the diagnostic character of the contact angles. The amine

Jan 1, 1947