Search Documents

By S. Fabich

Since the very beginning of Polish copper mining, special consideration of sink shaft techniques through highly saturated Cenozoic rocks was required. Shaft freezing has been chosen as a method to consolidate these rocks. Due to the rock mass structure and water inflow potential, shaft sinking without freezing was considered dangerous. In the course of time, rock mass freezing technology and experience were evolved and this technology became safer and more reliable. New techniques appeared not only in the technical method of freezing, but also in the matter of designing. Computer aided techniques allow engineers to make a detailed analysis and view of freeze wall development. Nevertheless it is important to determine basic thermal rock properties. In this paper, the evolution of knowledge and engineering experience taken in Polish copper mines and current knowledge level in that matter were shown.

Aug 1, 2013

By Y. C. Liu, G. A. Alers

The anisotropy of Young's modules has been measured in a series of Cu-Zn alloys containing from 1 to 28 wt pct Zn and cold-rolled to 97.5 pct reduction in thickness. These modulus data show a transition in texture as a function of zinc content. In alloys containing 3 pct Zn or less, the texture is essentially that of copper. A transition is clearly seen to develop in 5 and 8 pct Zn alloys, and to have been completed in a 12 pct Zn alloy. Increasing the proportion of zinc to 28 pct does not produce any further changes in texture. The ease and clarity with which this texture transition can be seen in the modulus data is in great contrast with the inccertainty in the visual detertiination of the range of texture transition from a series of pole figures. It is also shown that the rolling texture of the high zinc content alloys cannot be a one-COIIIponenl texture, characterized by the (110)(112) ideal orientations, as usually assumed. A second, quite important component must also be present. Furthermore, the present data are inconsistent with matrix orientations on which the "oriented growth" hypothesis of the Formation of recrystallization textures is based. THE rolling textures of binary fcc alloy systems have generally been considered to lie between two terminal textures. One of these terminal textures is the copper type and the other is the 70:30 brass type. Alloys of intermediate solute content exhibit a texture which is said to be a transition between the two terminal textures. On the basis of efforts to correlate rolling and recrystallization textures, two concepts have been advanced in the literature on the nature of these transition textures. One school1 suggests that the addition of alloying elements, e.g., zinc, causes a gradual rotation about one of the (111) poles from the (358)( 523) ideal orientation of the copper-type rolling texture to the terminal {1 10)( 112) ideal orientation used to describe the rolling texture of 70:30 brass. This concept is depicted in Fig. 1 with the angle of rotation corresponding approximately to the zinc content and is designated here as the "rotational concept", since the ideal orientation of the transition textures varies continuously with alloy content. The other concept,' the "mixture concept", suggests that the copper-type rolling texture is a two-component texture. {358) (523) and {110)(112). The addition of alloying elements affects only quantitatively the relative amounts of these two components—a decrease in the amount of material in the {385}(523) orientation and an increase of that in the {110)(112) orientation with increasing solute content. An experimental distinction between these two concepts is essential to a better understanding of both the mechanism of formation of rolling textures and the subsequent formation of recrystailization textures in fcc metals. Because of the lack of resolution inherent in pole figures, it has not been possible to differentiate between the two concepts on the basis of this data. Both concepts, in fact, make use of the same set of pole figures but interpret them in a manner acco-rding to the view held.'" Experimental results obtained from inverse pole figures or selected-area electron diffraction3j4 simply -yield more refined pole figures but do not eliminate the ambiguity of interpretation. Quantitative measurement of an entirely different, orientation-dependent property must thus be considered

Jan 1, 1967

By Karl E. Starch

This Bureau of Mines report is a background study of severance taxes on mineral production. The rates, bases, and other features of State severance tax legislation as of March 1978 are presented, as are the amounts of State severance tax collections for fiscal year 1977, Some statistical comparisons between severance tax collections, total State tax collections, and total value of mineral production in the States involved are presented to portray the relative importance of severance taxes both in State tax revenue systems and in mineral industry revenues. A general discussion of the purposes and principles of taxation, the unique nature of a mining enterprise, the various types of taxes imposed on mineral production, and the character and rationale of the severance tax and its impacts on mining firms sets the severance tax in perspective. A bibliography of materials on the severance tax is included.

Jan 1, 1979

By T Walton, C Perring, M Pepper, G Gerber

The Yandicoogina Channel Iron Deposit (CID) is an accumulation of iron pisolites cemented by a goethite-rich matrix. The Yandicoogina CID’s are found in a palaeochannel that meanders within a broad structural basin of the Yandicoogina Syncline in Pilbara region of Western Australia. RTIO Yandicoogina Mine Geology team contributed to a number of strategies maximising the iron ore reserves mined by Rio Tinto. Two strategies are discussed: the replacement of the Batter-Berm final pit walls by contour dozing; and upgrading the lower grade material to crusher feed. 1. Contour dozing – traditional Batter-Berm pit final wall configuration left kilometre long wedges of ore sterilised around bench margins. Contour dozing final walls (ie dozing of ore down the ore-waste contact) as internally defined by RTIO Yandicoogina Mine Geology (Mine Geology), enabled recovery of additional crusher feed. 2. Upgrade of lower grade material – the lower ore domain (GVL) within the Yandicoogina orebody contains numerous clay pods. Contaminant Al2O3 inherent within clay pods can result in CID material outside of crusher feed grade specifications, causing it to be flagged as ‘internal waste’ in mining models and permanently lost to waste dumps. In 2011, after multiple tests, Mine Geology demonstrated that this material could be upgraded to crusher feed via wet processing. With the support of the RTIO Metallurgical Development team new grade specifications were defined. The resulting material has been used to supplement higher grade ore. While increasing the mining ore output, these ongoing value-adding strategies also promote more sustainable mining via better use of the non-renewable iron ore commodity. The initiatives extend mine life, reduce waste movement, improve strip ratio and increase productivity

Mar 22, 2022

By D. Kruse, M. Sanaei

"A three dimensional nonlinear finite element model was constructed to simulate and analyze the behavior of large diameter segmentally lined shafts when subjected to seismic waves. To reduce computation time, a less complex shell model was also constructed. Transient excitation was applied to the supported nodes of both models, at the base of the shaft, with a time-function representing the 1994 Northridge earthquake. The models are developed at the end of an original phased construction-stage analysis of the shaft. Displacements, forces and moments are monitored and compared during the analyses steps. During the initial 15 seconds of the earthquake, the top and bottom of the shaft show similar displacements. The maximum horizontal displacement within the shaft is approximately 3.5 inches in the solid model and the shell model results conform to this by a factor of 50%. Keywords: Segmentally Lined Shaft, Soil Structure Interaction, Seismic Analysis, Finite Element Modeling, Ground Modification INTRODUCTION TO SEGMENTALLY LINED SHAFTS Large diameter segmentally lined shafts (SLS) are underground systems, constructed sequentially using precast concrete segments to form a ring which provides both temporary earth support during excavation and permanent structural support. The segments are connected via alignment pins, bolts, packer material and other structural components that ensure the continuity of the SLS. In this analysis, the construction process uses a top-down sequence wherein each soil layer is excavated, damp-proofing is installed and concrete segments are assembled to form each ring. This process is repeated until design depths are achieved completing the shaft. It is known that cylindrical structures sustain lateral (earth) pressure mainly through the mechanism of hoop-stress. As Timoshenko’s ring theory goes, a cylinder shell structure is prone to buckling under external pressure [1]. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. However, in shafts with large diameter to wall thickness ratios, buckling could become a critical issue. In any given mode, as buckling occurs in a ring, some sections of the structure move inward while alternating sections protrude. Although the presence of the surrounding soil could mitigate the buckling by resisting the movement (Soil structure interaction) seismic loads can cause ground movements and lateral pressures, exceeding the capacity of the structure. It is therefore essential to design the load bearing capacities of the shaft to minimize the possibility of any catastrophic failure due to earthquakes. This study explores the structural response of the SLS when subjected to seismic loads."

Jan 1, 2016

By D. Mason, W. J. Birch

Blasting operations are arguably one of the most contentious areas of surface mining.Many operators carry out outine monitoring as required by Mineral Planning Authorities. However in so doing they only concentrate on the observed Maximum Peak Particle Velocity (PPV) being below the statutory limit and pay little or no attention to the measurable parameters that determine this value (e.g. scaled distance, burden, detonator type, blast type or rock type). Such practice is “monitoring to comply”. What is needed is for the operators to adopt a methodology that clearly demonstrates to the appropriate regulators that the operator is “planning to comply”. The aim of the exercise being to deliver a process that is seen to be transparent, accountable, and quantifiable, which seeks to minimise environmental impact whilst not compromising the efficiency of the blasting operations mine.

Jan 1, 2011

By R. L. Stanton

"The present contribution is complementary with a preceding one on the field association of the conform-able ""pyritic"" deposits. It considers the more important features of their mineralogical constitution and their microtextures, re-examines the present interpretations of these, and of-fer-some alternative explanations. The term ""pyritic"" for these de-posits is m many cases a misnomer, as two quite distinct ore types are inuolve. One is a banded pyritic sphalerite-galena-chalcopyrite ore (for which the term '•pyritic"" is in-deed quite suitable), while the other is non-banded and is composed essentially of pyrrhotite and chalcopyrite. In addition to these constitutional differences, each is distinctive in general appearance and texture. The occurrence of two such consistent but clearly distinguishable ore types is attributed -rather than to difference in source material and pressure-temperature conditions of deposition -to the contribution of similar source material to dissimilarly oxygenated environments of sedimentation. Textures in the banded ores generally thought to be indicative of replacement or of high-temperature exsolution are explained by slow, law-temperature segregation in situ during compaction, folding, and regional metamorphism."

Jan 1, 1960

By K-O. Mickelsson, S. Töyrä, H. Esbensen

Accurate information of physical, chemical and metallurgical quality characteristics such as moisture content, iron grade and particle size are crucial for successful process control and for producing products within customer specifications. Correct moisture content of pellet feed is an important variable for successful balling of iron ore pellets and to minimize power consumption in the sintering process. Control of the filtering process in the pelletizing plant is therefore essential for both productivity and high product quality. The current measurement systems for moisture content at LKAB are based on two types of manual grab sampling, subsequently analyzed with rapid moisture determination methods. Previous studies of the measurement systems have indicated high sampling variability resulting in lowered possibilities for successful process control. The objective of the present study is to evaluate an alternative filter sampling approach and testing of on-line Infra-Red analysis (IR-analysis). On-line IR-analysis has the advantage of eliminating physical sample extraction and allowing for continuous monitoring of moisture content. However, this approach is sensitive to the surrounding environment, making careful calibration and control crucial for the quality of measurement results. Furthermore, as IR-sensors only target the surface of the conveyed pellet feed, several incorrect sampling errors need to be considered and counteracted to eliminate sampling bias and reduce the remaining measurement variability. Variographic characterization was applied to the two current grab sampling approaches of combined filtered material, to the alternative filter sampling method, and to the On-line IR-analysis. The results indicate that both the sampling of separate filters (using composite sampling and ISO-standardized moisture analysis), as well as a calibrated and well- maintained IR-sensor can improve the relative variability significantly, by lowering the total measurement system variance from 60% to 25%.

Jan 1, 2018

By Emilia Visileanu, Eftalea Carpus

"Ecological economic policy shall be understood as the sum of political, economical and environmental measurements aimed at the entire economy dematerialization and the dematerialization shall be ""imposed"" since the designing stage of goods and services"". European textile and clothing industry with a long leading tradition in terms of innovation, fashion and creativity, continues to be one of Europe's major industrial sectors. Textile industry affects the environment by high consumption of water, energy and chemicals, as well as by the large amount of waste it generates as a result of using a large number of chemicals and technological processes.Textile waste prevention, reduction and ecological exploitation require the implementation of new management and education tools.Introduction“Europe must learn from the experience of global economic and financial crisis ""- this was the conclusion of the European Commission that has elaborated a ten-year strategy designed to reinvigorate the economy and make possible a growth which is ""intelligent, sustainable and favorable to inclusion"", by a better coordination of national and European policies.Adapting infrastructure and logistics that encourage the marketing of ""sustainable"", ""fair traded"" and ""green"" products as well as other special „green” products will facilitate the movement towards dematerialization and eco-efficiency among producers."

Jan 1, 2012

By G. L. Gates

Five possible sources of water for waterflooding of petroleum reservoirs in the arid San Joaquin Valley of California were considered. Three of them (water produced with petroleum, water from a shallow saline aquifer, and waste irrigation water) were analyzed chemically; laboratory information for one (sea water) had been developed during a previous study. A series of laboratory tests made on the fifth source (fresh water) determined the solubility of calcium sulfate dihydrate in water. Laboratory analyses included the following: Chemical analyses of water produced with petroleum and waste irrigation water; solubility of calcium sulfate dihydrate in water and brines; the effect of excess sulfate on the solubility of calcium sulfate in brines; the presence of sulfate-reducing bacteria; and the permeability of cores from a petroleum reservoir to air, to water from other petroleum reservoirs, and to waste irrigation water. The results showed that most of the waters and mixtures of waters are compatible with petroleum reservoir waters and are generally suitable for injection. The calcium content of some of the formation waters is quite high, and care must be taken to prevent precipitation of calcium sulfate dihydrate. The permeability of the few cores tested was about the same to water and brines as to air, indicating that formation damage due to clay swelling will not be serious. The waters most likely to be available for injection are water produced with petroleum, water from shallow saline aquifers, and waste irrigation water.

Jan 1, 1970

Jan 1, 1994

By H. Wilhelm, E. L. Davis, W. A. Clark

MATHEMATICAL formulas for the analysis of the behavior of producing oil wells can be devised which will be correct for the assumed conditions. However, in an oil zone, variables always exist which are unknown, or to which. it is impractical to assign mathematical values. It seems apparent that one should reason back from observed facts to an analysis of causes, rather than start with a hypothetical reservoir with assumed properties and attempt to explain observed phenomena. In this paper we hope to throw some additional light on factors influencing production, especially edgewater behavior. OIL and gas are contained in reservoirs of either the sealed type or the edgewater type. In the former all the recoverable oil is produced by gas expansion only. In this type of reservoir, edgewater is not effective. This may be because of faulting or overlapping strata, or more often, probably, the edgewater pressure is ineffec¬tive on account of resistance or lack of head.

Jan 1, 1933

By H. Kenworthy

Sulfide-ore concentrates containing cobalt, nickel, copper, lead, and iron from the operations of the National Lead Co. at. Fredericktown, Mo., were treated successfully on a laboratory scale to recover more than 90 percent of the cobalt, nickel, and copper. A cobalt -nickel-bearing, lead-copper matte., produced by the St. Joseph Lead Co. at Herculaneum, Mo., was treated to produce a lead-zinc fume, a copper sulfide concentrate, and a cobalt nickel-iron product, netting a recovery of over 75 percent of the cobalt and about 90 percent of the nickel and copper. National Lead Co. bulk concentrates were chlorinated with gaseous chlorine to form anhydrous metal chlorides and sulfur chlorides, sulfur chlorides were recovered by distillation, a high percentage of the ferric chloride was converted to ferric oxide, and the chlorinated residual metals were extracted with water. Metal ions were removed from leach liquors by pH-controlled fractional precipitation as hydroxides. Cobalt solutions "were prepared from cobaltic hydroxide, and procedures were developed to remove contaminating metal ions. Purified cobalt solutions were employed as electrolytes for deposition of high-purity cobalt.

Jan 1, 1953

By Yuliy Rubinstein

"The paper presents a analysis of the history and the trends of development of flotation apparatus. The laws of their evolution are stated and the place and role of column flotation are indicated. It is demonstrate development and different design of column apparatus. The major parameters of column cell such as diameter and height are discussed. Options are proposed on optimization of hydrodynamic characteristics of columns with large-capacity cells. High efficiency of columns with cell height of 4-6 m is shown on examples of coal preparation. A new generation of multi sectional column cells has been developed. In the cells are zones with different aerohydrodynamic parameters: combined in the machine are co-and counter- counter flows of phases. The transition from single-chamber column to multi-sectional apparatus makes it possible to create favourable hydrodynamic and aeration regimes in each section of the column dependent on the pattern of material distribution by floatability. Efficiency of application different designs column apparatus uses shown on the example of enrichment of various non-ferrous metals ores and coal. The principles of mathematical simulation of the flotation process are developed. A scaling-up procedure for column cells was based on flotation macro- and micro- dynamics simulation.INTRODUCTIONColumn flotation is considered to be one of the most significant achievement in the field of mineral processing in the end of last century. We cannot but agree with this statement but would like to understand what underlies this success. History of the flotation column can not be considered in isolation from the development of flotation apparatus on the whole. It can be argued that the first attempt to switch from oil flotation to the use of bubbles during flotation was performed Bessel brothers in 1877 (Berlin patent 42 class 22, July 2) and in 1886 (Berlin patent 39,369 May 12). According to these patents, the crushed ore was mixed with oils , hydrocarbons and water. Then the pulp received in this way was heated up to boiling . Air bubbles and steam formed during boiling facilitate the flotation of ore particles coated with oil (first patent) or bubbles been generated by the reaction of lime with acid (second patent). The evolution in the design of the flotation apparatus incorporates the following key stages. Further development is connected with the Francis Elmore’s idea to use gas bubbles received at water electrolysis (UK, 13578; 1904). This method was not introduced then, but much later, in our time and on the essentially new technical basis it found a use for sewage treatment (electroflotation). Gas bubbling under vacuum patented also by Elmore (UK, 17816; 1904) obtained a practical use. It should be noted that the method did not lose its importance till now. The design of the camera has been surely optimized (Glembotskii etal, 1963). A year later A. Macquisten (UK, 26712) developed pressure (compression) flotation. Thus, the H.Sulman, H.Picard, D. Bell’s (US, 853120, May 29, 1905) basic patent and the adjoining T. Goover’s patent 1910 (US, 953746) formed the basis of the first and most important element of modern flotation: flotation with air bubbles sucked in from the environment. In 1914, J.Callow received a patent for on an apparatus where air was sparged through the porous false bottom of the cell ( US, 1104755). Woolen fabric folded four times was fixed on a perforated metal frame to be used for air sparging (Gaudin, 1932). The following year Durrel created the prototype of the injection (ejector) apparatus. The jet aerator made it possible to significantly reduce the size of the bubbles, in comparison with the filter cloth. An apparatus with slurry pre-aeration in an airlift prior to feeding into separation cell was developed Wagner in 1917 (US, 1235083). And finally, the first column apparatus with a counter-current of slurry and air was developed by M. Towne and S. Flynn in 1919(US, 1,295,817). ("

Jan 1, 2018

By Oren C. Baptist, Carlon S. Land, Eliot J. White

The water sensitivity of the oil - gas - producing sandstones in three fields in the Patrick Draw area of southwestern Wyoming was estimated by laboratory testing . The tests used to estimate sensitivity , which is a measure of the loss of well productivity if the producing formation is invaded by fresh water , are : Porosity ; permeability to gas , water , and brines ; saturation characteristics with air displacing water from the samples and by mercury injection ; and identification of clay minerals by X - ray diffraction . Laboratory results indicate that the degree of water sensitivity of the sands in the Patrick Draw, Table Rock , and Desert Springs fields vary , in that order , from moderately sensitive to highly sensitive . The main cause of the sensitivity appears to be the movement of fine particles in the pores , but the swelling of a small amount of an expandible clay mineral may also contribute to the permeability reduction observed in the samples . Laboratory results further indicate that the permeability of the sands to fresh water is seriously reduced if they are first flushed with sodium chloride brine ; calcium chloride brine is less harmful to the sands than sodium chloride brine . The low original permeability of the oil sand in the Patrick Draw field , together with its moderate sensitivity , indicate that the rate of water injection for the secondary recovery of oil will be low . Limited field experience in two pilot - injection wells confirms this prediction .

Jan 1, 1964

By Daniel W. H. Su

A nearly 305-m- (1,000-ft-) wide sandstone channel was projected to run through the mid panel area of a 457-m- (1,500-ft-) wide longwall panel in a southwestern Pennsylvania coal mine. This sandstone channel was known to cause serious longwallface roof control problems in the mine?s B-panel area in 1998 and 1999; and most recently, it induced many large face cavities and caused a substantial production delay in the preceding panel. For the two B panels mined in 1998 and 1999, hydraulic fracturing of the massive sandstone was conducted to facilitate better caving, thus relieving cantilever compressive stress at the longwall face. Vastly improved longwall face condition was observed and four weeks of mining delay due to bad roof conditions were eliminated. The implementation of the hydraulic fracturing technique, results of underground observation and measurement, and results of numerical modeling were summarized in a paper presented in the 20th International Conference on Ground Control (Su et al., 2001). This article is a summary of the activities that took place during a four-month period (October 2011 through February 2012) at a Consol Energy longwall mine southwestern Pennsylvania to improve face conditions and safety of underground personnel during mining of the 457-m- (1,500-ft-) wide longwall panel. The elevated concern for safety was driven by adverse face conditions encountered while mining the preceding longwall panel. Many of the problems were attributed to a thick and massive sandstone channel. A joint task force consisting of coal operations engineering, Pennsylvania operations engineering and CNX Gas personnel was formed in August 2011, which recommended drilling four hydraulic fracturing holes along the center axis of the sandstone channel to reduce pressure and improve face conditions at the longwall face. To further provide detailed monitoring of the longwall face and to evaluate the effectiveness of the hydraulic fracturing program, the Longwall Visual Analysis (LVA) software (Hoyer, 2011) was installed in early December 2011 to track the face pressure and c

Jun 1, 2013

By Walter Valery, Sarma Kanchibotla

Due to the global financial crisis, the world economy has turned upside down and most major economies in the world are facing severe recession for the past one and half year. During this period most commodity prices have tumbled by more than half from their peaks and such a sudden and severe economic downturn is not seen since the great depression. This sudden drop in commodity prices and lack of credit made many mining operations unviable and even those mines that are marginally viable at this point are operating under severe cost pressures and capital expenditure restrictions.

Jan 1, 2010

By B. J. CROSS., Henry Kreisinger, John Blizard, C. E. Augustine

This bulletin presents the results of 36 tests made on a 468-horsepower Edge Moor boiler fired with pulverized coal at the Oneida Street Station of the Milwaukee Electric Railway & Light Co., Milwaukee, Wis. The tests were made by the fuel section of the United States Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation. Illinois coal was used as fuel; the furnace, burners, and feeders were designed by the Locomotive Pulverized Fuel Co. The object of the tests was to determine what over-all boiler efficiency could he obtained with pulverized coal under various conditions of furnace operation and with coal of different fineness and moisture content. The investigation was thorough. The pulverized coal, as it was supplied to the furnace, was weighed in specially designed tanks placed on platform scales. Twenty-nine of the tests were of 24 hours duration, three of 16 to 18 hours, and four of 12 hours. All tests are reported excepting two-8 and 20-which had to be stopped abruptly, No.8 because a motor actuating the coal-feed screw burned out and No. 20 because of trouble with the feed pump. Tests 1 to 27, inclusive, were made with round burners and tests 28 to 3Rwith spreading burners. In the first nine tests a large excess of air was supplied in an effort to prevent the ash fusing at the bottom of the furnace. In tests 10 to 16 the supply of excess air was reduced in order to get a high efficiency, regardless of the slagging of ash at the furnace bottom. Tests 17 to 27 were made with a water screen about 10 inches above the bottom of the furnace, to make possible the burning of coal with a small supply of excess air without the ash fusing at the bottom of the furnace. Tests 28,29, and 30 were made without the water screen and with a small supply of excess air, and tests 31 to 38 with a water screen around the walls near the bottom of the furnace. Tests 32, 33, 34, and 35 were run with coarser coal than that used ordinarily at the plant. Tests 36,37, and 38 were made with undried coal.

Jan 1, 1923

By W. D. Mcmillan

Important reserves of nickel ore occur in the Levies district in Oriente, Cuba. The area is mountainous and mostly covered by heavy vegetation. The ore bodies comprise surface tracts of nickeliferous laterite underlain with decomposed serpentine of ore grade. The Cuban Nickel Co., a wholly owned United States Government corporation, owns a plant for leaching the nickel from its ores at Nicaro, Oriente, Cuba, Between December 1943 and March 31, 1954, 5,902,225 short tons of ore was treated, with a recovery of 116,206,519 pounds of nickel (52,711 metric tons). In 1953, 1,330, 224 short tons of ore was mined and 27;"3,129 pounds of nickel produced. The Cuban Nickel Co. also owns a townsite, with the necessary facilities, mining equipment, and 11 miles of railroad. Ore for the plant has been produced from the Ocujal-San Juan claims on lends owned by the Nicaro Nickel Co., a sub¬sidiary of Freeport Sulphur Co. The Government enterprise is man-aged by the Nickel Processing Corp. The Cuban Nickel Co. has denounced mineral concessions and has purchased other claims from private owners.

Jan 1, 1955

By C. Beckermann

"A diffuse interface model is derived for the direct simulation of two-phase flows with surface tension, density differences between the phases, and phase change. The derivation starts from the balance equations for a sharp interface and uses a formal averaging procedure on an atomic scale to obtain diffuse interface versions of the equations. Two approaches are considered: (i) the two phases have different velocities inside the interface and separate conservation equations are solved for each phase, and (ii) the two phases have the same velocity inside the diffuse interfuce and mixture conservation equations are solved. Based on a superposition of microscopic (atomic-scale) and macroscopic interface morphologies, an expression for the interfacial momentum source term is introduced that models surface tension effects and accounts for immiscibility between the phases.IntroductionDiffuse interface methods have been a popular tool in the direct simulation of two-phase flows [I]. In diffuse interface approaches, the interface between the two phases is characterized by a rapid but smooth transition in the properties, such as density and viscosity. Usually, a phase function ? is introduced to represent this transition, and the evolution of ? in the domain is computed from a separate equation or recipe. A unique set of conservation equations (e.g., mass and momentum) is solved on the entire domain, irrespective of the phase present, by accounting for the transition in the properties and introducing terms that account for interfacial sources. The continuum surface force (CSF) model of Brackbill et al. [2], which accounts for surface tension, is an example of the latter. The volume-of-fluid (VOF), level set, and phase-field methods are all examples of diffuse interface approaches. The major advantage of diffuse interface methods is that explicit tracking of the interface and the application of traditional sharp interface conditions are avoided. A disadvantage can arise from the artificial smearing of what is in reality an interface of atomic-scale width; however, techniques have been developed to overcome this problem."

Jan 1, 2004