Search Documents

The feasibility of exploiting a mineral deposit by developing a surface mine is closely related to the environmental protection and land reclamation costs. This issue has utmost importance for West Macedonia Lignite Centre (WMLC) of Greece, where there is still a lot of interest for opening of new mines and for further development of the existing open-pits. The decision-making process in these cases can be based on a decision tree that takes into consideration the various cost components of environmental management, the alternative solutions, the environmental permits and the cost reports of environmental management actions carried out so far. Moreover, the mine planning procedure is affected indirectly by numerous uncertain environmental and socioeconomic parameters, such as the delays caused by the bureaucratic procedures and the settlement of arguments in the Court.

Jan 1, 2006

By Tang Chaobo

Employing manganese carbonate ore and zinc oxide dust as material, Mn-Zn compound oxide powder for soft magnetic ferrite was prepared by a serial methods, as follows: leaching by using sulfuric acid, removing aluminium and silicon by neutralization and flocculation method, using ammonium bicarbonate to co-precipitating Mn and Zn, calcinations and washing to removing impurity content. The optimal technical condition was obtained by experiments. The difficulty of removing impurity such as Si, Al, Ca, Mg, from leaching solution was solved. The impurity content in the production meets with the preparation standard of high quality soft magnetic ferrite. The compound oxide powder obtained in the experiment was made into lower power loss magnetic ferrite, the quality of magnetic ferrite meet the standard of PC40 which was established by TDK corporation.

Jan 1, 2006

By Robert Roggenthen

In 1994, ASARCO's Mission Complex Mine Planning Department designed a new stripping schedule to take advantage of reserve opportunities. Based upon the new stripping design, overburden removal exceeded available hauling capacity. This increased hauling capacity requirement required that ASARCO consider alternative technologies for material transport. In 1997, ASARCO Mission Complex completed the purchase and installation of a 3.5 km, 8,600-tph conveyor system to transport waste material. The conveyor system is composed of two apron feeder/sizer units manufactured by Mining Machine Development LTD. and a conveyor system manufactured by Krupp-Robbins. This paper will review the option of truck haulage versus conveyor transport for overburden removal by (1) describing engineering studies contributing to the solution, (2) researching proactive options to create alternative management decisions, and (3) revealing final results of the project.

Jan 1, 1998

By S. C. Bandis, N. Barton

During drilling of deep boreholes, local mechanical failures of the wellbore walls may occur due to the inability of the incompetent overburden and reservoir rocks to withstand drilling-induced changes of the stress environment. At present, borehole failure mechanisms in three-dimensional stress fields are poorly understood. Our experimental investigations based on 3-D physical models demonstrate the stabilizing effect of the intermediate principal stress. The latter may play a dominant role in maintaining the integrity of the stress relieving failure zone around the borehole. However, this will depend on the stress anisotropy, the angle of hole deviation and on the angle of internal friction. Our tests also indicate that the failure zone can accomodate high extensional strains. Finally, relations between the physical models and closed-form elasto-plastic solutions are discussed.

Jan 1, 1986

By Mark E. Smith

To allow recovery of gold values from ore which cannot be economically processed by the mill, Pinson Mining Company has developed a run-of-mine heap leaching facility. In order to estimate production scale recovery rates, reagent consumption and percolation problems, a series of pilot scale tests were performed. These tests typically consisted of 3,630 metric tons (mt) (4,000 tons) leach ore at a grade of .94 to 1.56 grams Au per metric ton (g/mt) (.03 to .05 oz. Au/ton). Test heaps were loader stacked to approximately 4.3 meters (14 feet) high. Information from these pilot scale tests was employed in the design and construction of the production scale facility. Parameters such as spray rate, leach cycle, sprinkler placement, and barren solution chemistry were determined by the pilot tests.

Jan 1, 1984

Existing fluid flow techniques may be readily applied to the design of ranges for seam gas drainage. The Reynolds number characterises the flow regime within the pipe and it can be used in conjunction with data on absolute pipe surface roughness to determine the system friction factor. The application of the solution to the isothermal compressible flow equation utili- sing Moody friction factors and the concept of equivalent length of pipe for fittings and valves provides a practical method for sizing gas ranges. The physical capacity of a range can be decreased by the existence of significant quantities of water in the range and also by the ingress of air into the system at poor pipe joints etc. Both problems can be elimin- ated by adequate attention to design detail.

Jan 1, 1982

By Sheng-hai Yang

The electrochemical synthesis was conducted in anhydrous ethanol solvent mixed with conductive reagent when tantalum plate was used as anode and stainless steel plate as cathode. The effects of different conductive reagents (such as NH4Br, (CH3)4NCl, (C4H9)4NCl), conductive reagent concentration and the space on the cell voltage and the current density were investigated. The current efficiency of electrosynthesis was more than 95%. The electrolyte, a mixed solution was then undergone air distillation and vacuum distillation to get the final product which was characterized by Fourier Transform Infrared(FTIR) spectroscopy, Raman spectra, 1H-Neclear Magnetic Resonance(1H-NMR) spectroscopy. Carbon and hydrogen contents in the product were determined by elemental analysis instrument. Results consistently show that the product was tantalum penta-ethoxide.

Jan 1, 2006

By F. Lawson, N. A. Sareyed-Dim

A rotating disk of iron precipitant in a high temperature batch reactor has been used to study the kinetics of precipitation of nickel from low concentration aqueous solutions. Under inert atmosphere conditions, for temperatures up to 150°C, the rate of nickel deposition at pH25°C of 5 to 6 is controlled both by the rate at which nickel ions reach the surface and the rate of chemical reaction at the surface. However, the presence of oxygen in the atmosphere above the reacting system increases the nickel deposition rate dramatically. It is suggested that under the experimental conditions used, hydrogen atoms are adsorbed on both the iron and nickel, thus reducing the number of sites available for the cementation reaction. Oxygen acts as a depolarizer for hydrogen.

Jan 1, 1977

By Oleg Terichow

Electrophoretic mobility measurements were made by the Bureau of Mines on samples of a Florida phosphate slime to determine the optimum conditions of coagulation and settling in an aluminum sulfate solution. Addition of anthracite to promote mutual coagulation demonstrated the practicability of heterocoagulation by reduction of the repulsive effect of double layers. By proper selection of the electrolyte and its concentration, the reduction of the double layers to a net zero point of charge causes the predominance of Van der Waals' forces of attraction leading to the coagulation and rapid settling of both particle systems, as is predicted by the Derjaguin-Landau-Verwey-Overbeek theory of colloidal stability. Confirmation was found in the microfiltration tests where a modified Carman equation was applied to evaluate the specific filter bed resistance.

Jan 1, 1975

By G. Ferrara

In process and plant simulation, more reliable prediction of industrial results and evaluation of data for designing purposes may be attained by the combined use of (a) modeling and simulation of ore characteristics and (b) modeling and simulation of integrated plant operations. The systems for modeling and simulation of ore characteristics are discussed as well as the conditions in which their use may be necessary (complex structure of the ore-body and variability of the ore fed to the plant). Two examples, for coal and bauxite run-of-mine (ROM), are reported. The procedure of linking the process unit models and the approaches for the solution of integrated systems are indicated. A general-purpose program for the simulation of integrated plant operations is described, and some examples of its use are reported.

Jan 1, 1984

By Wasyl Kunda

High grade jig and low grade flotation concentrates used in the following experiments, are produced from silver ore at the mine. The study was carried out to recover the silver and other metals from these concentrates by hydrometallurgical methods. The concentrates were subjected to two stage oxida¬tion leaches in a HNO3-H2SO4 medium. The dissolved metals were recovered by selective precipitation of: (a) silver chloride, (b) iron-arsenic-bismuth residue, (c) copper sulphide, (d) cobalt-nickel sulphide. The effluent solution contained only ammonium sulphate and ammonium nitrate. The silver chloride was further processed to the high purity silver powder by the AgCl ? Ag2S ? Ag2SO4 ? Ag° route. The recovery of silver from the concentrates was over 98% and other metals from 95 to 99%.

Jan 1, 1984

By C. A. Hansen

INTRODUCTION It has been the experience of the writer, during some. five years' work with electrolytic zinc, that the zinc cell is perhaps more- sensitive to impurities in the electrolyte than the analytical methods as yet developed for the chemical identification and determination of these impurities; but that, when proper purification methods have been applied to a given solution, the behavior of the cell is quite independent of the original sources from which the zinc sulphate has been derived. It has also appeared that the behavior of the zinc cell is the best and surest check on the correctness and thoroughness of the purification methods used, because it indicates the presence of both current impurities. and cumulative impurities derived from the leaching of the ore; it also in

Jan 3, 1918

By Alain Pecker

The choice of a design concept for a bridge foundation is guided by various factors; several of these factors are indeed of technical origin, like the environmental conditions in a broad sense, but others non technical factors may also have a profound impact on the final design concept. The foundations solutions adopted for the Rion Antirion bridge are described and an attempt is made to pinpoint the major factors that have guided the final choices. The Rion Antirion bridge is exemplar in that respect: the foundation concept combines the simplicity of capacity design, the conceptual facility of construction and enhances the foundation safety. The design of these foundations was a very challenging task which required full cooperation and close interaction with all the parties involved: concessionaire, contractor, designers and design checker.

Jan 1, 2013

By William A. Fuchs

A study of carbonaceous ore at the Santa Fe mine (Corona Gold Inc.) shows that there is no quantitative relationship between organic carbon content and preg rob, although much of this material preg robs. However, there is a relation between K20 and preg rob. Preg rob generally occurs only in those samples with greater than 2% K20. X-ray diffraction and chemical . studies show that the critical factor is the illite content of mixed (possibly interstratified) illite-smectite. Apparently illite, at a certain threshold, "geo-activates" the carbon. The potential for easily monitoring preg rob using a gamma ray spectrometer is discussed.

Jan 1, 1990

By John A. Johnson

Conclusions regarding the use or omission of stemming in blasting have not peen reached, pending completion of all aspects of this investigation. The results from the dust phase of this study on six classes of stemming prove that the kind of stemming affects the amount of dust produced from blasting. In previous work at the Mount Weather testing adit it was demonstrated that blasting produces the highest dust concentrations of any of the mining processes.5/ Under the conditions prevailing at the Mount Weather testing adit, the average of all rounds having a break of at least 95 percent showed that the least amount of dust was produced when no stemming was used.

Jan 1, 1940

By James D. Bennett

Relationships among mine and injured miner characteristics and HSAC's degrees of injury are examined for 91,404 injuries in under- ground bituminous coal mines in the United States from 1975 through 1982. Injury severity varies by the mining system, geographical region, circumstances surrounding the injury, the injured miner's age, whether the miner was using powered equipment, the year which the injury occurred, and the location in the mine where the injury happened. Injury severity is not related to the injured miner's total mining experience, job experience, and experience in the mine in which the injury occurred.

Jan 1, 1984

By A. C. Fieldner

DURING 1939, 286 by-product coke ovens were completed and put into operation. These included 140 Witputte ovens for the Carnegie-Illinois Steel Corp., at Gary, Ind.; 61 Koppers-Becker ovens for the Ford Motor Co., at River Rouge, Mich.; 65 Semet-Sotvay ovens for the Great Lakes Steel Corp., Zug Island, River Rouge, Mich.; and 20 Curran-Knowtes ovens for the Midwest-Radiant Corp. plant at Mitlstadt, Ill. The Millstadt plant is unique in carbonizing a washed coat containing 3.50 per cent sulphur. The gas contains approximately 2500 grains sulphur per 100 cu. ft.; this is successfully removed with sodium carbonate solution by the Seaboard liquid purification process. The coke is intended primarily for use as a smokeless domestic fuel in the city of St. Louis.

Jan 1, 1941

By Eduardo Lozano, Vilem Petr

The use of explosives bring countless benefits to our everyday lives in areas such as mining, oil and gas exploration, demolition or avalanche control. However, because of the potential destructive power of explosives, strict safety procedures must be an integral part of any explosives operation. The goal of this paper is to provide a solution against the hazards which unfortunately accompany the use of explosives. For this reason, a blast shield is specifically designed and tested for protecting personnel against these unpredictable effects. This document will develop a complete analysis answering the following questions: what are the potential hazards from an air blast; what are their effects; and how can we be protected against them. In order to answer these questions, theoretical, analytical, and numerical calculations are performed. Finally, a full blast shield prototype is tested under blasting conditions proving its effectiveness as a safety device while explosives are used.

Jan 1, 2015

By T. E. Harper, Gustave Reinberg

Electrolytic refining of all lead bullion produced at the Oroya smelter of the Cerro de Pasco Copper Corporation has been adopted as standard practice. A pilot refinery with a capacity of 25 metric tons daily has been in operation since June, 1934, and a new refining unit having an initial capacity of 100 tons per day is under construction. This program has been made possible by certain modifications of the usual Betts refining process1, developed at Oroya, which have the effect of making the purity of the lead produced, and the acid loss incurred in operating the process, entirely independent of the amount of impurities in the original bullion. The modified process, as developed and at present used, treats impure bullion direct, without presoftening or other prerefining step, except that if the bullion carries tin it is desirable to detin before casting into anodes, since tin carries over to some extent to the cathodes. The refining process developed differs from usual Betts practice in two essential particulars: the anodes are cast thinner and replaced at more frequent intervals, and anode slimes are washed by a system of counter-current dipping, prior to their removal from the surface of the anode scrap. Limiting the period of anode corrosion insures a cathode of high purity, since solution of impurities at the anode can occur only if the thickness of the anode slime blanket, and hence the voltage drop across it, becomes greater than a certain critical value. The dip washing system operates to prevent acid losses, by recovering the highly concentrated, nearly neutral lead fluosilicate solution present in the pores of the slime blanket on the corroded anode, and doing this in such a way that there is no opportunity for chemical decomposition to occur. The best illustration of the efficacy of these two expedients may be secured from records of more than a year's operation of the 25-ton pilot plant, during which period the acid losses were less than 2 Ib. of 100 per cent hydrofluosilic acid (H2SiF6) per ton of lead produced, and typical assays of bullion and refined lead were as shown in Table 1.

Jan 1, 1937

By MOHAMMAD R. H. GORAKHKI, Christopher A. Bareither, MANUEL APARICIO, Joseph Scalia IV

The focus of this study was on the evaluation of hydrologic and environmental behavior observed in GeoWaste and waste rock test piles. GeoWaste is a mixture of fast-filtered tailings and waste rock prepared as a tailings-dominated mixture. The two test piles included potentially acid-generating (PAG) waste rock and were operated for 26 months to evaluate whether GeoWaste can suppresses sulfide oxidation and production of metal-rich acid mine drainage relative to PAG waste rock. The test piles were constructed in the shape of truncated 5-m-tall pyramids with 25-m base sides and flat 5-m × 5-m top surfaces. Water content, temperature, electrical conductivity, and oxygen concentration were monitored in four layers and at five locations within each layer in both test piles. In addition, 5-m × 5-m lysimeters were installed at the base of each pile to collect leachate. Approximately 2660 mm of water was added to the surfaces of the test piles via precipitation and irrigation (irrigation ≈ 1050 mm applied at an approximately constant rate for 70 days). The measured saturation, oxygen concentration, electrical conductivity, and temperature in the GeoWaste and waste rock piles suggest more sulfide oxidation occurred in the waste rock pile compared to the GeoWaste pile. Observations from the pile experiments suggest that co-managing mine waste in the form of GeoWaste reduced acid generation compared to waste rock alone due to the lower permeability and unsaturated state of the GeoWaste pile that reduced downward migration of moisture and inhibited drainage.

Mar 31, 2021