Search Documents

The Calypso geothermal field, mapped by the R V Sonne (cruise SO-135) in 1998, includes four main sites, the Northern Vent Area (centred on 37¦ 36.7'S, 177¦ 06.2'E, area 1.5 km2), Central Vent Area (37¦ 39.4'S, 177¦ 05.2'E, 1 km2), Southern Vent Area (37¦ 41.7'S, 177¦ 06.0'E, 1 km2) and Mercury Vent Area (37¦ 41.3'S, 177¦ 07.3 'E, 0.5 km2). Hydrothermal activity at the vent sites is controlled by minor, sub-parallel NE-trending normal faults. Gas bubble trails (C02) and shimmering hot water vent from fractures and joints between large blocks of silicified volcaniclastics and in depressions in the sediments at the base of these outcrops. Measured maximum vent temperatures are between 180¦C and 201¦C. Venting fluids are at, or just below, boiling for water depths of 200 m. Rock samples recovered by dredge from the sites include massive anhydrite, clay-altered pumiceous ash, silicified volcaniclastic sediments and volcaniclastic breccias cemented by sulphur. Clay-altered samples, dominated by randomly interstratified illite-smectite and accessory chlorite, indicate formation environments of 70¦C to 90 ¦C. Native sulphur is abundant throughout the samples. Fine-grained (<1 mm) disseminated pyrite and vein pyrite occurs in the clay-altered pumiceous volcaniclastics and argillites. In the Southern and Mercury Vent Areas, fine-grained orpiment, realgar and cinnabar have deposited in the sandy matrix of volcaniclastic breccias. Amongst the cinnabar, small (<2 mm) beads of native Hg formed on the surface of several rocks following their recovery. These samples also contained abundant light hydrocarbons, which coat the rocks with an oily sheen.

Jan 1, 1999

By J. A. Luppens

Five years ago, Phillips Coal Company decided replacing mainframe/workstation programs with a new package of PC software was clearly the best solution for computer reserve modelling. The system chosen was actually three programs distinguished by their power, cost, flexibility and integration, and ease of learning and use. Phase I involves the use of the "StratiFact" program for borehole data management and seam correlation. This phase is probably the most neglected, yet critical aspect of reserve evaluation. Phase II employs the "PC/Cores" package for modelling and volumetrics. Phase m is "PC-Cut" which provides mine planning tools including an automated cut generator.

Jan 1, 1996

By Paterson R. G, Compston W

The Mine granite at the Ardlethan tinfield is dated by Rb-Sr on a muscovite concentrate at not less than 417 ± 2.5 Ma (2s), consistent with the intrusion of this granitic body into folded Late Ordovician sediments. A combination of Rb-Sr and K-Ar evidence suggests a slightly younger age, 41O ± 2.5 Ma, both for the neighbouring Ardlethan Granite and for the hydrothermal alteration of the Mine granite, with which the tin is associated.On this basis, the somewhat high 206Pb/204Pb of two galena samples from within the hydrothermal alteration zone is best explained by an increase in U/Pb of order 10 per cent during a geochemical event in the Late Precambrian, in the rocks which eventually yielded the Pb to the mineralising fluid. This earlier event probably increased Th/U in these rocks as well, by as much as 5 per cent. If these reconstructions are valid, the lower-than-average U/Pb implied for the original Precambrian source rock bespeaks a mantle component of marginally greater proportion than for "average orogene".

Jan 1, 1982

By J T. Woodcock, G J. Sparrow

A sample of pyrrhotite flotation concentrate pulp assaying 15.3 g/t Au, which had been prepared from an old tailing dump, was treated to extract the gold. Examination of the concentrate with an SEM showed that exposed or free native gold, 5- 40 ¦m in diameter, was present but no locked gold was observed. Direct cyanidation of the concentrate to extract the gold showed that the flotation reagents present inhibited gold extraction. A range of pre-treatments was used to overcome these effects. Direct cyanidation for 48 h extracted only 26 per cent of the gold, indicating possible contamination of the gold in the concentrate with flotation reagents. Pre-treatment of the concentrate pulp by aeration for 24 h, or by 72 h aeration with an addition of 3.65 kg/t of sodium sulphite, gave little improvement in gold extraction by subsequent cyanidation. Pre-treatment by filtration, or by aeration with 12.5 L/t 100 volume hydrogen peroxide, followed by cyanidation for 48 h gave gold extractions in the range 67-77 per cent. Combining filtration and an aeration period with hydrogen peroxide addition raised the subsequent cyanidation extraction of gold to 88 per cent, giving a tailing assaying 1.5 g/t Au. Re-cyanidation of some of the dried tailings from the initial tests extracted most of the remaining gold giving a tailing assaying 0.5 g/t Au. This indicated that most of the gold was available for dissolution by cyanide. The poor dissolution of gold by cyanidation of the untreated concentrate was attributed to the presence of flotation reagents. It was shown by UV spectrometry that xanthate-containing compounds were present in the solids fraction of the original pulp and that they were partly removed by pre-treatment. MIBC was also present, and dithiophosphate, which was used in the flotation step, was also probably present. The results indicated that the improvement in gold extraction after filtration and oxidation of the original pulp was due to partial removal of the flotation reagents, and illustrates the detrimental effects that residual flotation reagents can have on the extraction of gold by cyanidation of a flotation concentration.

Jan 1, 1990

By Charles M. McCulloch

This Bureau of Mines report discusses the principles of using computers to draw maps and plot geologic data of mining areas. The types of maps that can be drawn by a computer are reviewed, using as examples two separate areas where poor roof and gas emissions caused mining problems. Such maps can be used not only to help identify problem areas, but also to predict areas where problems could occur, thus giving mine operators time to work out solutions prior to mining. The average cost of a computer-drawn map for a mine property is less than $100, including computer time and man-hours for data preparation.

Jan 1, 1976

By Mark Maday

As part of the I-94 North-South Corridor reconstruction program, the Wisconsin Department of Transportation (department) is reconstructing the Mitchell Interchange in Milwaukee, Wisconsin. Located on the south side of Milwaukee near Mitchell International Airport, The Mitchell Interchange interconnects I-94, I-43 and I-894. Reconstruction began in 2009 with the letting of the first advance contract for local crossroad bridge reconstruction. A second advance contract for construction of collector-distributer roads on each side of the I-94 mainline was completed in 2010. The main contract involving reconstruction of the core of the Mitchell Interchange was let in the summer of 2010, and is scheduled to be completed by the end of 2012. The core contract includes construction of three cut and cover tunnels along two system interchange ramps. Construction of the three tunnel structures is on the critical construction path. The contract includes an interim contract completion date that requires the tunnels to be open to traffic by the end of 2011. A top down method of construction using drilled shaft secant piles for the sidewalls of the cut and cover tunnel structures was selected as the preferred structure type to address subsurface and construction schedule challenges. The department identified in pre bid coordination that no cost reduction incentives would be reviewed or accepted for changes in tunnel wall type. A major component of the tunnel structures requires the installation of 1,500, 4-foot diameter secant piles. This paper presents mitigation strategies to manage construction risks associated with the installation of the secant piles including; prequalification of the secant pile subcontractors, requirement for use of full depth temporary casing, a site specific quality control plan, specifying drilling equipment, and developing a geotechnical baseline report for this critical component of the Mitchell Interchange reconstruction project.

Jan 1, 2011

By James A. Pendleton

In response to Public Law 95-87 (SMCRA), Colorado promulgated regulations governing the mining of Coal. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence. All permitted underground coal mines within Colorado have approved subsidence programs. Preliminary monitoring results indicate the subsidence mechanical predictions have been sufficiently accurate to preclude material subsidence damage. The State of Colorado has developed a practical approach to regulating subsidence, which stresses monitoring verification of predicted subsidence phenomena. However, shortcomings exist in our ability to precisely predict the secondary consequences of subsidence, including effects to structures, the hydrologic balance and the environment. Lack of accuracy in predicting these secondary consequences results in uncertainty, necessitating conservatism in permitting. To avoid increasingly stringent permit restrictions, future research should emphasize the secondary consequences of subsidence.

Jan 1, 1986

Mineral exploration and mining in New Zealand has had almost five years of new legislation. The requirement for different consents is a challenging, time consuming, expensive exercise but in most cases the new procedure is working, although the matter of obtaining access to land is still a major issue. Priority is critical. After lodgment of an application for a minerals permit there are many other matters to address such as identifying land owners, occupiers and administrators, preparation of access applications, consultation and preparation of various resource consent applications.

Jan 1, 1996

By K Belanger, J. Mclachlan, F. Stober, G. Norval, B. Snider, A. Munsch, T. Koehler, E. Piantino, J. Carlos Queiroz

The project to rebuild the smelting furnaces at the Anglo American - Barro Alto ferronickel smelter, located in Goias, Brasil, was initiated in September 2013. To optimize the capital cost, while maximizing furnace integrity and robustness, a design basis giving flexibility to ore composition variation was developed in order to ensure sustained nameplate production. The resulting capital efficient, fasttracked project execution was accomplished through the creation of an integrated project team of Anglo American and Hatch through FEL 3 and FEL 4 phases of the project. The integrated team addressed the project challenges through a cooperative and versatile approach, created by access to knowledge, experience and systems in both Anglo American and Hatch. The team could operate at an optimized speed of execution, as demonstrated in the FEL 3 and FEL 4 completion durations, as well as efficiently mitigating any risks of increasing cost or delaying schedule by utilizing lessons learned and team knowledge from Anglo American on the original green-field project and Platinum smelters and Hatch on similar reference ferronickel furnace rebuilds. Other critical drivers of project cost minimization and revenue loss/generation (considering production revenue of each furnace) are scheduled durations for construction, commissioning and ramp-up. The integrated team commenced construction, commission and ramp-up planning almost one year in advance of the shutdown and this paper will discuss the strategies developed to reduce risks and optimize the construction schedule to mitigate revenue loss and optimize ramp-up time to sustained operation at nameplate capacity.

Jan 1, 2015

By N. R. Morrow, C. C. Harris

The experimental points which describe capillary pressure curves are determined at apparent equilibria which are observed after bydrodynamic flow has ceased. For most systems, the time required to obtain equalization of pressure throughout the discontinuous part of a phase is prohibitive. To permit experimental points to be described as equilibria, a model of capillary behavior is proposed where mass transfer is restricted to bulk fluid flow. Model capillary pressure curves follow if the path described by such points is independent of the rate at which the saturation was changed to attain a capillary pressure point. Aemodified suction potential technique is used to study cyclic relationships between capillary pressure and moisture content for a porous mass. The time taken to complete an experiment was greatly reduced by using small samples. INTRODUCTION Capillary retention of liquid by porous materials has been investigated in the fields of hydrology,l soil science,2 oil reservoir engineering,3 chemical engineering," soil mechanics,5 textiles: paper making: and building materials In studies of the immiscible displacement of one fluid by another within a porous bed, drainage columnsl and suction potential techniques2 have been used to obtain relationships between pressure deficiency and saturation (Fig. 1). Except where there is no hysteresis of contact angle and the solid is of simple geometry, such as a tube of uniform cross section, there is hysteresis in the relationship between capillary pressure and saturation.2 The relationship which has received most attention is displacement of fluid from an initially saturated bed (Fig. 1, Curve R2), the final condition being an irreducible minimum fluid saturation Swr. Imbibition (Fig. 1, Curve A), further desaturation (Fig. 1, Curve R), and intermediate scanning curves have been studied to a lesser but increasing extent.2 ,3,9-12 This paper first considers the nature of the experimental points tracing the capillary pressure curves with respect to the modes and rates of mass transfer which are operative during the course of measurement. There are clear indications that the experimental points which describe these curves are obtained at apparent equilibria which are observed when viscous fluid flow has ceased; and any further changes in the fluid distribution are the result of much slower mass transfer processes, such as diffusion. Unless stated otherwise, this discussion applies to a stable packing of equal, smooth, hydrophilic spheres supported by a suction plate5 with water as the wetting phase and air as the nonwetting phase. The discussion can also be applied, in many

Jan 1, 1966

This paper briefly describes the shaft, including sinking, steel sets and their installation, shaft equipment and winders.INTRODUCTIONThe New Broken Hill Consolidated Ltd. Service Shaft is a vertical concrete-lined circular shaft, 20 ft. in diameter with -steel sets spaced at 12-ft. centres. The diameter of 20 ft. was established as the minimum that would enable the shaft both to house the proposed hoisting and service equipment and to satisfy ventilation requirements as a downcast airway. The 12-ft. set spacing was based on South African practice in similar types of shafts.The shaft extends from the surface to 28 ft. below No. 22 Level, a total depth of 3,194 ft. Sinking was commenced in September 1946, and equipping completed in January 1955. Initially the shaft was sunk and concrete-lined to a depth of 52 ft., using a stiff-legged crane and clam-shell grab for mucking. Operations were suspended at this depth to allow the installation of the steel sinking head-frame, winders and ancillary equipment.Sinking and concreting were recommenced after four months and continued to a depth of 1,035 ft. 6 in., where the shaft connected with a pilot opening. The concrete lining was poured as sinking progressed and was piped from the surface to this depth, after which all concrete was lowered in buckets and discharged through a distributor suspended in the shaft. A cycle of stripping to the pilot opening and concreting was continued until the shaft reached No. 22 Level. From this level the remaining 28 ft. was sunk full size. All plats were cut and concreted as sinking progressed.

Jan 1, 1957

By P. K. Leung, S. R. Allada, P. M. Dranchuk, D. Quon

The alternating direction explicit procedure (ADEP) makes use of the boundary conditions to reduce multi-dimensional problems to a series of one-dimensional problems. The method, previously applied to reservoirs containing only an under-saturated oil, has now been extended to cover the case of natural gas reservoirs. l his involves solving a non-linear partial differential equation, application of the procedure is straightforward and no calcuIational problems were encountered. INTRODUCTION There has been a growing interest in formulating mathematical models of petroleum and natural gas reservoirs — models which permit the engineer to examine and evaluate the physical and economic consequences of various alternative production policies. The tremendous reduction in the cost of solving such models in recent years has made possible their use as an almost routine management tool. This reduction is the result not only of improved computer hardware but also of the development of more efficient mathematical techniques. The present paper is concerned with the application of a recently proposed numerical method (ADEP) to two-dimensional gas reservoirs. STATEMENT OF THE PROBLEM Given a two-dimensional Region R, bounded by a closed Curve C (Fig. 1) such that the behavior on Curve C is known, the differential mass balance for each fluid phase in R, neglecting gravitational effects and assuming Darcy's law for fluid transport, can be written as:

Jan 1, 1967

A brief review is given of the history of the Colliery to date together with the reasons for the development of an additional seam.Investigations into the quality of the coal ami its suitability for the production of metallurgical coke and determination of the economic mining limits and coal reserves are discussed. The commencement of mining operations and the inter-seamarrangements necessary for the disposal of coal won are described with the stages in the opening out of the seam itself and the reasons for the installation of a 48-in. trunk conveyor belt. Choke and manning of face equipment are considered and also the work of secondary development and pillar extraction.It is concluded that with modern face equipment and conveyor belt lines, concentrated mining followed by immediate extraction of pillars is practicable and is giving excellent results at Burwood Colliery.INTRODUCTIONBurwood Colliery, the total holding of which now comprises some 3,140 acres of land and 1,450 acres of sea leases, has mined the Borehole Seam since 1883. The early work took place from Nos. 1 and 2 shafts at Glenrock Lagoon and later on at Nos. 3 and 4 shafts at Whitebridge to which the centre of operations shifted in 1893, shaft sinking at this latter area having commenced in 1888.As all the early operations were confined to the Borehole Seam, reserves of coal on this horizon had been considerably reduced by the mid 1930's, so a cross measure drift was driven to the Victoria Tunnel Seam which is about 300 ft. above the Borehole Seam, and fully mechanized coal winning commenced from the second seam in 1938. Subsequently this cross measure drift was extended to the Borehole Seam and complete mechanization of the south-west sections of this seam achieved by 1945.Four track mounted mechanical units were put into operation in the latter area and these worked in a southerly and...

Jan 1, 1958

With the change in legislation under the Resource Management Act 1991 (RMA), the responsibility for administering the effects of blasting on the environment, has transferred from an essentially central government system to local bodies. This naturally will allow for a variety of compliance levels and control procedures which will depend on the particular local body and rather ad hoc arrangements. It is anticipated that the existing NZ Standard on blast vibration levels will soon be replaced by the Australian Standard. These changes raise the question as to what should be used as suitable compliance levels to prevent damage to structures. The paper will address the measurement, control levels and the appropriateness of current standards in relation to the overall legal framework of the RMA.

Jan 1, 1996

By W. P. Roux

Owing to decreasing high-grade ore reserves, there is a need for better understanding of the jigging process to improve the recovery efficiency of finer, lower grade material. The use of positron emission particle tracking (PEPT) was examined as a technique to study the motion of iron ore particles inside a laboratory batch jig. PEPT is a non-invasive method that can provide three-dimensional kinetic data on a particle in laboratory-scale processing units and has been successfully used to study mills, hydrocyclones, and flotation. Experiments were conducted to determine whether PEPT would be a viable technique to study iron ore jigging and what valuable information could be obtained. The results indicated that detailed information on the stratification rate of a particle could be obtained, with adequate resolution to track the particle?s movement through an individual jig pulse.

Jan 1, 2014

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.

By R. L. Schmidt, J. D. Verhoeven

The diffusion coefficients and electrotralzsport mobilities of aluminum, gallium, and arsenic have been determined in molten germanium with the capillary reservoir technique. The diffusion coefficients are slightly higher than those determined by the solidification technique of Brirton et a1.1 It was found that aluminium and gallium migrate to the cathode in molten germanium) whereas arsenic migrates to the anode under an electric field. A possible technique for producing p-n junctions by means of electric field freezing is discussed in view of the experimental data. In the past decade or so the literature has abounded with articles concerning the solid-state properties of the semiconducting elements germanium and silicon. It is surprising by comparison how little has been published concerning the liquid-state properties of these materials. In the production of doped germanium or silicon the diffusion coefficient of the dopant in liquid germanium or silicon is an important quantity. Yet, to the best of our knowledge, no one has ever made a direct measurement of the diffusion coefficient of solutes in either molten germanium or silicon. A number of authors'-4 have determined some diffusion coefficients by the indirect technique developed by Burton et al.1 This technique appears to give numbers of the correct order of magnitude but it does depend upon a number of assumptions in the analysis and also requires prior knowledge of the viscosity of the melt. In the present work a more direct measure of the diffusion coefficients of arsenic, gallium: and aluminum in molten germanium has been made. It has been shown independently by two groups of authors5, 6 that, when an electric current is passed through the interface of a solidifying metal containing an impurity, the resulting electrotransport in the liquid boundary layer at the interface offers a mechanism for control over the redistribution of the impurity accompanying the solidification. These authors show that the degree of control is proportional to the mobility, U of the impurity atoms in the liquid boundary layer, where the mobility is defined as the drift velocity relative to the solvent per unit electric field. In principle the results apply to the solidification of a doped semiconductor and offer an interesting technique for control of the doping of a semiconductor. In the present work the mobilities of aluminum, gallium, and arsenic were determined in molten germanium in order to evaluate the potential usefulness of electro-transport as a technique for solute control when applied to the solidification of doped germanium. EXPERIMENTAL PROCEDURE Both the diffusion coefficients and the mobilities were measured using high-purity alumina capillaries and a resistivity technique for analysis. A schematic diagram of the electrotransport apparatus is shown in Fig. 1 and the details of the cell design are shown in Fig. 2. For the mobility experiments electrical contact with the bottom of the capillary was made with graphite, as shown in Fig. 2. In order to prevent electrical contact with the melt the graphite was coated with a thin layer of alumina using a plasma spray torch. The cell assembly, a graphite electrode, and another assembly containing two blank capillaries were fastened to the lavite disk shown in Fig. 1. To make a run the system was evacuated and the doped germanium was outgassed at the operating temperature of 1030°C. The cell and blank capillaries were then submerged beneath the melt and a slightly positive pressure of helium was introduced to fill them. After passing current through the cell for a given time the cell and blank capillaries were raised from the melt and the furnace was shut off. The temperature of the cells dropped below the freezing point of germanium within 1 to 2 min after the furnace was shut off.

Jan 1, 1968

Three large deposits of good quality lignite were located and delineated in the Central Otago region between October 1978 and July 1979. The program was initiated and funded by Mines Division of the Ministry of Energy as part of the national Coal Resource Survey. The exploration work was carried out by Lime and Marble Limited on a contract basis (Bowman, 1980). The three deposits were all potentially mineable by open cast methods and possessed combined indicated and, inferred reserves in the order of 1000 x 106 tonnes. They ranked with the previously discovered Eastern Southland 1ignites and as such constituted an important national energy resource. Fifteen months later a second more detailed investigation of similar duration was undertaken by the Liquid Fuels Trust Board (LFTB). The objective was to upgrade and refine the geological data base of all of the nine South Island 1ignite deposits in order to make preliminary economic assessments of their potential. Again Lime and Marble Limited acted as the exploration operator (Bowman, 1981a, 1981b, 1981c).

Jan 1, 1983

Safety is the No. 1 concern of any drill contractor or mine operator. Everyone in the industry knows a safe site helps stabilize operational costs and enables higher productivity. When it comes to exploration drilling, research has proven a majority of injuries are caused by the mishandling of coring rods. A driller helper will typically handle up to 50 rods per shift or up to 15,000 rods per year. With an annual 340 t (750,000 lb) in rods managed by hand, the risk of serious injury is extremely high. Because of this, the top request from the exploration industry is diamond rod handling. The Boart Longyear 4200 surface exploration drill, slated for release in 2009, will give the industry a hand-free, operationally safe rig.. Developed through the collaboration of its global drilling services and products divisions and targeted at the 1,200-m (3,900-ft) NQ market, the upcoming Boart Longyear 4200 surface exploration drill features the safest and most flexible rod management sys-tem in its class. The rig includes the industry?s first, truly hands-free rod handling system. This increases operator safety on the jobsite. In addition to the rod handler, the rig also features many new innovations that boost productivity and rig efficiency while minimizing the risk of downtime due to component failure or operator error. Boart Longyear has also included an intelligent PC-based operating system designed to allow complete drilling control as well as diagnostics reporting for the rig.

Jan 1, 2009

By V Kveldsvik, N Ragvin, T Eiken, G Grøneng, G V. Ganerød

Catastrophic rock slope failures have caused destructive tsunamis in Norwegian fjords. At the Åknes rock slope the tsunami generating potential is large due to the potential large volume involved in a possible catastrophic failure. Widening of the upper crack has been recorded since 1986, and in recent years, a quite extensive investigation and monitorin campaign has been conducted. Data from some of these investigations are presented and analysed with respect to a preliminary evaluation of the stability of the slope.

Jan 1, 2006