Search Documents

By P. Somasundaran, Tarun Bhambhani, D. R. Nagaraj, P. Patra

"Certain non-sulfide gangue minerals are known to have a detrimental impact on flotation performance. When present in large amounts, they can negatively affect recoveries, grades and throughput at current operations, and dictate the viability and economics of a greenfield project. While the problem has been investigated for a long period of time, a scientific understanding of the mechanisms by which these minerals affect performance has not been obtained, and no acceptable solutions have been developed. This study focused on the role of physical aspects (e.g. shape, size and morphology) of these minerals as the underlying factors for poor performance. Flotation tests were conducted using model mineral systems to understand the impact of one phyllosilicate mineral (muscovite) on flotation kinetics, recoveries and grades. The study reveals that there is minimal impact on flotation kinetics, no impact on recoveries, but a very strong detrimental impact on concentrate grade. The traditional mechanisms of transport such as true flotation and entrainment are not sufficient in describing the extent of transport. The transport is attributed to the unique platy morphology of muscovite, which allows for action of buoyancy forces. Data also shows that the muscovite transport to the froth phase depends on particle size; coarser sized muscovite (100-150@) report to the froth phase in much larger amounts than medium sized muscovite (50-100@). At finer size fractions (<50@) the transport is also increased, and this is likely due to entrainment."

Jan 1, 2014

By H. Fukuyama

The wetting behavior of single crystalline MgO by fayalite-type slag melts has been studied by the sessile drop technique incorporated with high temperature X-ray radiography. The experiments were performed under oxygen partial pressures of 10-6 and 10-4 Pa at 1473 K. Mass ratios of iron to silica, Fe/Si~, in the slag employed were 1.4 and 2.0. To investigate the interfacial reaction, experiments using high density MgO crucibles were also conducted. The reactions at the interfaces were examined by Electron Probe Microanalysis. The contact angles between the slag melts and the MgO substrates were found to be relatively low, ranging from 30 to 10 degrees. The surface tension of the slag was 0.4 N/m for a slag of Fe/Si02 = 2.0. Two phases, magnesiowiistite and olivine, were observed at the interface. Interdiffusivity in magnesiowiistite solid solution was determined as a function of iron oxide content. Phase relations between magnesiowilstite and olivine, and the growth rates of both phases, are also discussed

Jan 1, 1996

By Steven K. Ruggieri

Increased coal production on longwalls has brought with it higher levels of dust generation. Most U.S. longwall mining operators have difficulty complying with Federal dust standards, which are stricter than European standards. Longwall operators faced with a longwall that is "out of compliance" have implemented a variety of practices designed to reduce dust levels. Mining conditions and other important variables, however, can cause fluctuations in dust levels that may overshadow the performance of a new dust control technique. This can result in the continued use of an ineffective technique or lead to the abandonment of an effective dust control technique. No single technique can keep a longwall in compliance. Maintaining compliance requires a fundamental approach to dust control -- proper application and continued use of effective dust control techniques.

Jan 1, 1983

By John J. Mulligan

Coal is found in every major geographic region throughout Alaska and in two offshore areas. Since about 1852 over 100 small mines have opened and closed. Last years production was almost entirely from one mine in central Alaska. Clearly the utilization of Alaska&apos;s abundant coal resources presents political, economic and technical problems that are far from solution. Location and Physical Features Figure one illustrates the geographical and geological similarity between Alaska and western United States. The Arctic region of Alaska generally resembles Wyoming and the Dakotas. The Brooks Range is an extension of the Rocky Mountains. The Central region of Alaska between the Brooks Range and the Alaska Range bears a general resemblance to the basin and range country of western United States. The Southcentral and Southeastern regions has a similar resemblance to the Sierra Nevadas and the west coast of the United States.

Jan 1, 1982

By M. F. Werneke

Flotation of the carbonate, oxide and silicate minerals of copper (malachite, azurite, chrysocolla) has been the subject of much research in recent years, but few effective solutions to this problem have been found. With decreasing reserves of sulfide minerals, the economic recovery of these "oxides" appears to be an important source of copper for the future. Xanthates have been known for many years to be malachite collectors (1), but only at very high dosages, or at lower dosages following activation of the mineral by sulfide ion. Dewitt and Batchelder (2, 3) found that chelating agents such as certain oximes were collectors for malachite and azurite, but also required high reagent dosages. Fuerstenau (4) has suggested, for example, that potassium octylhydroxamate may be an effective collector for malachite, On the other hand, Balberyszski (5) has found that oxide minerals may be completely sulfidized at high temperatures with gaseous sulfur or H2S, and then floated with conventional collectors. None of the above approaches appear to offer an economically effective method for the direct flotation of these oxide minerals.

Jan 1, 1977

By C. A. Clark

The Chagres Smelter is located 80 kilometres north of Santiago - Chile, in the middle of an agricultural valley which is also one of the poorest districts in the country. This condition sets the main focus for the smelter&apos;s Corporate Social Responsibility (CSR) programmes, which ultimately aim at building self sustainable social and economic capital in accordance with the local capacities. With the help of Anglo American&apos;s SEAT (Socio Economic Assessment Toolbox), a corporately developed instrument designed to help the operations understand the needs of the communities and the impacts of those operations, the Chagres Smelter implemented several programmes, such as the CETTA (Experimental and Applied Technology Transfer Centre) programme. This project started in 2003, and consists of creating a centre for the transfer of sustainable techniques and skills for the small agricultural and livestock producers that live in the rural areas near the Chagres Smelter. Its main impacts are: Improved production quality (goat cheese and bee honey) and access to relevant markets, improved training and self-sustainability levels of producers, enhanced socio-economic level of the District&apos;s inhabitants by improving their income earning opportunities and technical knowledge, creation and promotion of a local brand as a symbol of quality products from the valley and a positive environmental impact of good breeding and native flora protection practices in the area. Other relevant social programmes are the &apos;Environmental Strivers&apos;, which created a recycling centre in the community; and the &apos;Beautiful Valley" project, which provides management knowledge and skills to local youngsters and leaders who can contribute to finding solutions for local environmental needs.

Jan 1, 2007

By A Coelho, D Bruce, H Grosser, C Parken, M Xia

Carrapateena is a new underground sublevel cave mine and was officially opened in 2020. It has a mine life of 20 years. Development began in 2016, and with the rare opportunity to start a with a blank canvas and having a long mine life, an effort was made to explore how to incorporate innovative and leading-edge technologies. The Ventilation on Demand (VoD) system was designed with the objective to optimise power consumption and ventilation delivery through the primary and secondary ventilation systems. Primary fans controlled by Variable Speed Drives (VSDs) and dualwinding secondary fans with multiple setpoints control the delivery of overall quantity. Automated butterfly dampeners control the regulation of air to individual production crosscuts, and automated louvres control the exhaust quantities from the mining levels. Ultra-sonic flow sensors are installed to measure air quantity and environmental stations are installed to measure air quality. Both are designed to play a key role in control and calibration of the system. It was quickly identified that no one vendor could provide a holistic solution to meet the design requirements. A strategy was derived to use multiple vendors, harnessing the specific strengths of each. A control system has been developed to allow the Site Operations Control Centre (SOCC) to oversee and control real-time delivery of ventilation as required by operations. The first full level installation of the VoD system was completed in September 2020.

Mar 15, 2021

By E. H. Jr. Dix

THE use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong-aluminum alloys, magnesium is present to the extent of ½ to ¾ per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth1, 2,3,4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high purity aluminum manufactured by this company .5

Jan 1, 1929

By William Catron

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and cuts in the various reining districts of the United States. The mining methods described are those used in the mines of the Cananea Consolidated Copper Co., a Mexico corporation whose holding company in the United States is the Greene Cananea Copper Co. The mines are at Cananea, Sonora, Mexico, 25 miles directly south of the international boundary, approximately in 31° nor to latitude and 110 to 130° west longitude. Cananea is connected with the boundary towns of Naco and Nogales, Ariz., by a standard-gage railroad.

Jan 1, 1930

Table A-1. Number of underground coal mines and samples collected for underground occupations, 1988-92 [ ]

Jan 1, 1997

By Murat Alkan

In this study, a self-propagating high-temperature synthesis (SHS) and following acid leaching techniques were carried out to produce boron carbide (B4C) powder. First, B2O3 was obtained through calcinations of H3BO3 at 1073 K for 2 hours. Then, the glassy B2O3 obtained was crushed and sieved. In the SHS experiments, different amounts of B2O3, Mg and C black were used. The SHS product was obtained in the form of black, spongy solid. In the leaching step, the SHS product was leached in a HCl solution to eliminate the MgO and Mg3B2O6. The effect of acid concentration on the selective leaching was studied at different concentration range, solid/liquid (S/L) ratio, and temperature. The products obtained were characterized by using X-ray diffraction, chemical analysis and SEM techniques.

Jan 1, 2009

By H. E. Hilliard

A method was investigated for detecting and counting filamentous iron bacteria in open recirculating cooling systems. It is simple and fast and does not require trained microbiologists. Samples from 26 systems were examined. Cells were cultivated on commercially prepared ready-to-use media. Cultures grew well on this medium and were identified as filamentous iron bacteria by microscopic examination and by their ability to deposit iron using the prussian blue reaction.

Jan 1, 1976

By C. M. Dentan

Conventional testing of crude kaolin ores emphasizes physical properties as they relate to end uses of kaolin products. This approach to evaluating crude ores does not reveal the basis of behavioral differences between typical coarse and fine kaolins from central Georgia. Optical and scanning electron microscopy in combination with XEDS have been employed to characterize both coarse Cretaceous and fine Tertiary kaolin in order to shed light on the reasons for the gross differences in their properties. Routine evaluation of various parameters was also carried out. Bulk densities were 1.48 g cc-l for the coarse clays and 1.53 g cc-1 for the fine clays. Surface areas were 15 m2 9-1 and 25 m2 9-1, respectively. Brookfield viscosities were low for the coarse clays at 70% solids, and high for the fine clays. The situation was reversed for Hercules viscosities. Sixty percent of the coarse clays had particles of less than 2 um and the fine clays had 90% less than 2 cm. Micrographs of thin sections prepared from blue-dyed epoxy-impregnated crude ores and of SEM fabric samples demonstrated vivid differences in texture. Cretaceous kaolins appeared to be completely recrystallized residual products of former aluminous sediments, while Tertiary kaolins retained their essentially sedimentary character. Differentiation of the coarse and fine kaolins is rapidly accomplished by both optical and scanning electron microscopy, and should be considered a valuable analytical technique in evaluating kaolin ores.

Jan 1, 1981

By Sevinc Yildirim, Cigdem Oruclus

"Metal-Porous Silicon (PS) based structures dipped in water show the direct hydrogen fuel cell behavior. The effect of the thickness of the cupper (Cu) film on the electrical properties of direct hydrogen fuel cell is studied by fabricating Cu/Porous Silicon/n-Silicon/Indium structures. PS samples were produced electrochemical etching of n-type single crystalline silicon with a resistivity of 1,25 Ocm and (111) orientation. The thin films of Cu with different thickness between 200 and 600 nm were deposited on PS surface by electron-beam technique. Investigation of the effect of Cu layer on the performance of the structure indicates that the performance parameters such as open circuit voltage (Voc) and short circuit current (Isc) strongly depend on the Cu layer thickness. It was observed that the divice with an 350 nm Cu layer exhibits the highest open circuit voltage (0,5 V), short circuit current (0,01 mA) and power density (10 W.m-2).IntroductionHydrogen is the most attractive and ultimate candidate for a future fuel and an energy carrier. Hydrogen is recognized as the environmentally desirable clean fuel of the future since it can be used directly in different types of hydrogen fuel cells [1]. In the past years, the rise in portable electronics requires the development of miniature fuel cells compatible with standard silicon micro fabrication technology. Most silicon micro-fuel cells have used the polyperfluo-rosulfonic acid membranes (Nafion R) as a proton exchange membranes (PEM) that is not really integrated with standard micro fabrication techniques [2-5]. The composite materials such as inorganicorganic hybrid materials (Nafion-silica, Nafion-borosiloxane etc) are next generation of proton conducting membrane [4-8]. But, fuel cells run on pure hydrogen gas, which can be produced with other energy resources. Hydrogen smallest atom and thus the H2 gas can leak easiliy. The application of hydrogen for power sources has been greatly restrained due to the lack of safe and convenient generation and storage methods.A kind of hydrogen fuel cells Metal-PS-Si structures used as an energy water directly. There is no need pure hydrogen. Cu-PS-Si Schottky-type fuel cells with as proton-conducting membrane and the thin-film cupper catalist and water as fuel, which are interesting for fabrication of lowcost miniature fuel cells. Generation of the open-circuit voltage and short-circuit current has been observed by Cu-PS-Si structure dipping in different hydrogen-containing solution."

Jan 1, 2014

By Jorge Alberto Soares Tenório, Victor Bridi Telles, Denise Crocce Romano Espinosa, Felipe Fardin Grillo, Vicente de Paulo Ferreira Marques Sobrinho, José Roberto de Oliveira

"This research aims to study the process of incorporation of the metal iron in electric arc furnace dust (EAFD), from a steel mill producing long steel by liquid iron in addition to the changing temperature of 1400 degree Celsius altering experimental conditions such as how to add the EAFD (as received and in the form of briquettes), the percentage of EAFD to be added (10, 20 and 30% of initial weight of sample pig iron) and the time of withdrawal of the sample of pig iron and slag (30 minutes after the addition of EAFD). Previously, the EAFD will be characterized using the following techniques: chemical analysis, particle size analysis, X-ray diffraction, scanning electron microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) microanalysis. After characterization, the eletric arc furnace dust to be added to the bath of liquid iron, will be divided into 2 types: the first order of addition will be in the form ""as received"" from the plant and the second is through the agglomeration of EAFD in the form of briquettes. The achievement of fusion experiments in laboratory scale, will take place in a vertical tubular furnace with temperature control. The fusion experiments to assess the incorporation of the metal iron will use graphite crucibles. A flow of inert gas (argon) will be maintained inside the furnace during the experiments. It is expected that the results obtained at the end of the research allow the evaluation of the iron metal incorporation of eletric arc furnace dust in hot metal bath.IntroductionThe steel industry generates a variety of solid wastes, liquid effluents and gaseous emissions at various stages of processing. The electric furnace dust (EAFD), generated in electric arc furnaces, represents a major problem for their content of chemical elements such as zinc, iron, chromium, cadmium, among others, issued to the atmosphere during the manufacture of steel[1]."

Jan 1, 2012

By H. Ramazi, A. Amini

"This article is devoted to the introduction of a new technique of electrical resistivity data processing called residual resistivity (RR). We define RR as measured resistivity minus background resistivity. To determine the background resistivity, the data acquired from electrical resistivity measurements along a given survey line is evaluated, and then an equation is fitted to the data corresponding to a chosen measurement station as a function of current electrode spacing (or array length). The RR technique was applied to several synthetic models to compare the conventional resistivity inversion of each model with its RR-based inversion. A case study was carried out in a karstic area in Zarrinabad, Lorestan Province, western Iran, to detect the location and geometry of probable cavities by conventional resistivity inversion and RR-based inversion. The results showed that the anomalous zones are better highlighted in the RR-based inversion images in comparison with the conventional inversion images. In some cases, anomalies detected by the RR-based images were hidden in the conventional method. IntroductionThe geoelectrical resistivity method has been widely used since the early 20th century, and plays an important role in several fields such as groundwater and subsurface mineral exploration, geotechnical and environmental investigations, and archeological studies (Bayrak and Senel, 2012; Candansayar and Basokur, 2001; Fehdi et al., 2011; Hee et al., 2010; Osella et al., 2003; Wilkinson et al., 2010). The goal of geoelectrical resistivity surveys is to determine the distribution of subsurface resistivity by measuring the current-potential difference on the ground surface (Aizebeokhai et al., 2010). In the electrical resistivity method, an electrical current is injected into the ground by two electrodes, called current electrodes (AB), and the potential difference is measured between another pair of electrodes, the potential electrodes (MN). Several methods of interpretation are available for application to electrical resistivity data, the simplest being the graphical interpretation of the apparent electrical resistivity pseudo-sections along each survey line. A second method, electrical resistivity inversion, has been developed to create relatively accurate two- and threedimensional computational resistivity models of subsurface sections (Loke and Barker, 1996; Niwas and Mehrotra, 1997; Nordiana et al., 2014; Oldenburg and Li, 1994; Papadopoulos et al., 2009; Yilmaz and Narman, 2014). In the inversion method, models of subsurface objectives are mathematically inverted to reach optimal solutions subject to prescribed objective functions, constrains, and convergence criteria. A common problem when using the electrical resistivity inversion method is that the inversion model of an electrical resistivity profile may be non-unique because different inhomogeneities in the investigation media can result in the same electrical response (Smith and Vozzof, 1984)."

Jan 1, 2016

By Joshua Micah Hoffman

While it is easy to state that meaningful involvement of the community can play a critical role for a successful blasting operation, following through with this involvement is not an easy task. Structured Public Involvement (SPI) is a developed protocol for involving communities in project planning decisions and could be readily applied to the blasting industry. SPI was developed for the purpose of collecting quality public input about public transportation projects. The purpose of SPI is to bring about stakeholder satisfaction with potential projects by allowing controlled input from the stakeholders. It was designed and intended for democratic societies that have come to expect a voice in public projects. While blasting operations are not always in the domain of public projects, the fundamental process outlined by SPI can be useful for collecting feedback from the immediate public around blasting operations.

Jan 1, 2014

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By Lin Li, Xiang Li, Yifang Zheng, Jilai Xue, Jun Zhu

"Al drops and gas bubbles in the anode-cathode space of aluminum electrolysis cell are of great importance for cell operation improvement in metal loss, current efficiency and energy consumption. A direct observation on the Al drop, gas bubble and ultrasound was carried out through a see-through cell. The Al drop immersed into the cryolitic melt was found moving up and down irregularly in the anode-cathode space without electrolysis, which was then completely dissolved into the melt. During electrolysis, the Al drop came to the anode area and reacted with the gas bubbles generated on the anode. Under ultrasound, the gas bubbles were removed from the anode surface while the Al drop was kept on the side of anode. The observed phenomena were useful for technology improvement in reducing the anode-cathode distance or lowering the energy consumption in aluminum electrolysis.IntroductionDuring aluminum electrolysis, aluminum metal drop and anodic gas bubble are in close contact each other within the anode-cathode space, and the interaction between them can produce significant impact on metal loss, current efficiency and energy consumption. The motions of the Al drop and the gas bubble are also related to the dissolution of aluminum metal into cryolitic melt and the cell voltage drop due to the bubble layer covering the anode surface.A number of studies have been carried out using different types of see-through cells, where the dissolving process of metal Al into cryolitic melts (metal fog) in the anode-cathode space was directly observed and photographed [1, 2]. With the similar method, some direct observations on the anodic bubble behaviors with and without ultrasound were performed during aluminum electrolysis [3-6]. However, to our best knowledge, there is no published work on direct observation on the behavior of Al drops and anodic gas bubbles staying together within the same anode-cathode space, as well as the motion and interaction of them in cryolite-alumina melts."

Jan 1, 2011

By C. Boudreault, M. Fortier, S. Fafard

In the forging industry, the increasing trend is to use DC cast billets as forging stock to replace extruded stock. However, there is little technical information available in open literature. In order to gain a better understanding of the behaviour of cast stock during deformation, a study was initiated to evaluate the impact of an homogenisation treatment on the billet prior to cold forging. Axisymmetric upsettings of cylindrical samples machined from DC billets were achieved in order to evaluate and compare flow stresses, crack initiation and propagation. Results show a 30% decrease in flow stress after homogenisation. Observations of the deformed samples show major cracking for the as-cast material. Optical microscopy and SEM observations have related the crack initiation to decohesion around ß -AlFeSi particles and subsequent growth along the constituent path. Homogenisation effectively breaks up and transforms the ß phase, present as platelets in the cast product, into smaller spherodised a-AlFeSi particles. This has the effect of preventing crack growth in the forged product. The homogenisation treatment also resulted in the reduction of Mg and Si in solid solution. The softer matrix generated 29% less die wear when compared to the as-cast structure. Based on the results of this study, it is thus recommended to homogenise cast billets prior to cold forging.

Jan 1, 2006