Search Documents

By Henry Hibbard

Fox the purpose of this paper all steels will be divided into two divisions: effervescing and non-effervescing. This classification must be borne in mind as many statements true of one class are not true of the other. Effervescing steels are those that effervesce in the molds, evolving large volumes of gases, which, in escaping, throw up a spray of molten particles of steel and give the molten metal in the mold a rapid stirring or churning motion until it freezes, or, at least, becomes pasty. This effervescing is intended and proper. The non-effervescing steels, which are more or less completely killed, should not evolve any gas in the molds. Many years ago the writer proposed to call the two classes of steels evolution and solution steels, depending on whether the gases in the molds are evolved or kept in solution, but the present designations seen to be better. In America, at least, effervescing steels are in a class by themselves and include steels made for boiler, tank, and ship plates, steel pipe, soft steel wire, wire nails, soft machinery, and structural steels. These are all low-carbon steels with less than 0.40 per cent. carbon. Low-carbon steels that do not effervesce but are killed are also made; these are put into ingots and castings but they are outside the limits of this paper. Effervescing steel is cast into square or slab molds, either top or bottom poured. Most of the effervescing steel is made in the basic open-hearth furnace, though much is made by the acid Bessemer process and a little is made in the acid open-hearth. It is not made by the crucible or electric-furnace process, in which the volume of gas required cannot be produced in the steel and evolved from it in the mold to give the effervescence desired. Any steel ingot, when teeming is finished, is of a certain size or volume. Leaving out of consideration for the moment the lessening of the over-all dimensions of the ingot through contraction due to loss of heat, the ingot may be placed in one of three classes: It may settle, losing in volume; it may stand, that is, remain constant in volume; it may rise, that is, increase in volume.

Jan 9, 1919

By Antônio Augusto Gorni, Fabio Adriano da Silva, Emanuelle Garcia Reis, Afrânio Márcio Costa

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. Stands out the capacity to produce different thicknesses in a same plate, therefore allowing special service for sectors such as building structures, bridges, shipbuilding and mechanical applications. The purpose of this study is to present the first results obtained in this innovative product in Brazil. Some slabs of EN10025-2 S355JR+AR steel were rolled and were evaluated the dimensional tolerances, mechanical properties uniformity, grain size, surface and internal qualities. In addition, a correlation was observed between slab and plate thickness reduction and internal plate quality. The results show that this technology can be used with adequate performance for these steel grades in the current market.

Oct 1, 2019

By Michael K. Rhodes

A 120 tonne per day BacTech bacterial oxidation plant treating refractory gold concentrates for Gold Mines of Australia's Youanmi project in Western Australia commenced operation September 1994. This was the first commercial application of the BacTech process. A pilot plant trial on concentrates produced from Youanmi ore was carried out at BacTech's laboratory in Perth. Results and measurements from this trial were used by Signet Engineering Pty Ltd to design the commercial plant. This paper cover the results obtained from the piloting, their implementation in the plant design and the initial commissioning of the full scale plant.

Jan 1, 1995

By F. C. Gennari, D. M. Pasquevich

With the gradual exhaustion of natural rutile, there has been extensive research into its synthesising from lower-grade titanium minerals. The removal of Fe from pseudobrookite (Fe2TiO5) by chlorination was studied, using both isothermal and non-isothermal thermogravimetric measurements. Correlation of the results obtained from element distribution maps, scanning electron microscopy, energy-dispersive X-ray analysis and phases detected by X-ray diffraction in the chlorinated samples showed clearly two associated processes. First, the pseudobrookite particles reacted with chlorine and iron was removed selectively as FeCl3(g), leaving a solid residue rich in the TiO2 phases anatile and rutile, separated from an inner layer of unreacted pseudobrookite by a distinct interphase boundary. Second, chlorine allowed TiCl4(g) to form in the reaction bed, where it removed iron from the Fe2O3 crystals as FeCl3(g) and substituted Ti through a pseudomorphic reaction

Jun 21, 1905

By Roger St. C. Smart, Paul Weber, Joan E. Thomas, William M. Skinner, Warwick Stewart, Stuart Miller

For mine sites affected by acid rock drainage (ARD) or with a potential future ARD issue, the prime consideration is not only the classification of different waste rock as potentially acid forming or non acid forming but also the peak acid (and metal) release rates and expected ARD duration during which effective ARD management and acid neutralisation capacity (ANC) are required. Methods for assessment of this ANC (e.g., Sobek tests) are already available but can be unreliable in ARD containing significant proportions of framboidal pyrite or iron carbonates. The measurement of negative ANC values and the release of S to solution showed that significant sulfide oxidation may occur prior to and during testing in samples containing reactive (particularly framboidal) pyrite resulting in serious underestimation of the original ANC. A simple methodology with dissolution in Ar-purged water before ANC testing, removing ferrous salts, and sulfate assay after ANC testing corrects these effects. Results also showed that a significant lag period (up to 432 h) may be needed for complete hydrolysis of Fe associated with the standard Sobek ANC testing of, for instance, siderite. Hence, the ANC of iron carbonates is usually significantly overestimated. By filtering and the addition of H202 until there was no subsequent pH drop (due to Fe hydrolysis reactions), followed by back titration to pH 7.0, the ANC for siderite was similar to the ANC determined after 432 h lag by the Modified Sobek ANC test and to the mineralogical carbonate ANCcarb determined by calculation based on electron probe micro-analysis. A chemical ANC calculation, based on neutralising cations released to solution, has provided a method to quantify the short-term ANC of carbonates and silicates in simple mixed mineral assemblages and waste rock samples. Results showed that silicate ANC can be more important in short-term neutralisation than carbonate ANC in low carbonate samples. In the longer-term, decreasing sulfate and metal loads with increasing pH values suggests that eventually sulfide acidity generation rates will match the longer-term inherent acid neutralisation rates of the sample derived from silicates. A kinetic ANC measurement for silicates, after steady state dissolution is reached, that indicates the number of hydrogen ions neutralised/m2/yr has been developed. These values can be used in estimates of the net acid production profile from wastes with low (and decreasing) pyrite content after the short-term ANC is exhausted.

Jan 1, 2004

By Paloma Camargos, Saulo De Rezende

In the pursuit of sustainable development, the mining industry is constantly evolving, recognizing the importance of utilizing all extracted materials. Nexa addresses waste management in the mining industry, with an emphasis on the adoption of waste as innovative and sustainable raw materials. With a focus on exploring the potential of mining waste, the characteristics of materials from the Vazante and Ambrosia units were evaluated to determine their suitability as aggregates in the construction industry, as well as to identify other possible applications.

Sep 29, 2023

By A. Fahr, T. Byczkowski, M. Genest, C. Mandache

"Layered aluminum structures assembled with rivets are often found in aircraft fuselage. These structures are exposed to various mechanical loads and a range of environmental conditions that contribute to their ""aging"". The rivet holes are the source of stress concentrations and the location of crack nucleation and growth. Detection and sizing of second and third layer cracks under fasteners represent a major challenge for non-destructive evaluation (NDE) technicians. Electromagnetic methods are currently the most feasible NDE techniques that are capable of successfully inspecting such structures. However, different probe lift-offs, due to protruding rivets and paint coatings, or interlayer separations, due to sealant or air gaps, pose difficulties in detecting and sizing cracks. In addition, the use of conventional eddy current technique is limited due to the inverse relationship between the probe spatial resolution and its field penetrability. In this paper, we present an alternative approach that overcomes the previously mentioned shortcomings by using pulsed eddy current excitation and magnetoresistive sensor pick-up. Various signal manipulations are employed for defect detection and quantification."

Jan 1, 2006

By ZhiLong ZHAO, Lin Lin, Zhancheng Guo, Jingtao GAO, Huiqing Tang

Grain sticking often occurs in the fluidized bed reduction of f ine iron ore, which is closely related to the precipitation morphology of metallic iron on the surface of ore particles. In this work, simulating the gas-solid reduction process of iron ore, in situ observations were carried out to investigate effects of doping mineral oxides on the precipitation morphology evolution of metallic iron during reduction of iron oxides with CO. Results indicate that the precipitation morphology of metallic iron is related to the quantity of doped mineral oxides. The minimum mole fraction of doped oxide ( xyOA N ) that can inhibit the growth of iron whiskers is related to its cation radius ( Ax r ), extranuclear electronic layers ( Ax n ) and valence electrons ( Ax q ). Their relation can be expressed as:

Jan 1, 2016

By Robert A. Medower

This paper will review the operational benefits of applying contemporary control technology to balance the blast to a cupola. Reported benefits from existing installations include reduced channelling, higher pour temperature, reduced oxygen consumption, lower coke consumption & reduced emissions.

Jan 1, 2001

By Y T. J Kwong

With the recent emphasis worldwide on environmental protection and sustainable development, finding an enriched mineral deposit no longer guarantees mining development. Only if the identified resource can be exploited in an environmentally-friendly manner is it possible that a mine may be developed. Designed primarily to aid with exploring for similar deposits of a particular type, traditional genetic ore deposit models tend to ignore the fact that all mineral deposits are characterised by type-specific environmental signatures. In fact, how an ore deposit can be mined, the commodities of interest extracted and the resultant mine wastes managed are all largely dictated by the geology and mineralogy as well as the environmental setting of the deposit. An environmental ore deposit model integrates such related information to identify the environmental challenges associated with mining an ore deposit of a particular type and facilitates the selection a suitable combination of methods to minimise environmental risks and impacts. Given that environmental management consumes a large portion of the budget for a modern mining project, making informed decisions at all stages of mining development can reduce the overall project cost. Through case examples, this paper demonstrates how environmental ore deposit models may be useful in mine permitting, active mining and in site decommissioning. It is only through an innovative and flexible approach that the mining industry can shed its tarnished image and gain the social license to mine.

Aug 22, 2011

By Paulo Cesar Pavan

T&T or Traceability, is a concept of generating, storing and on demand providing information about all traceable items in the supply chain

Jan 1, 2019

By Shawn P. Coughlin, Michael A. Schimmenti, Juan Leonardo Tello del Pino

"The Sistema de Potabilización Área Norte project (Northern Area Purification System) was a major expansion of the potable water system in Buenos Aires Province, Argentina. The aim of the project was to transport and purify raw water from the Paraná River to provide potable water for five communities in the northern part of the province, benefitting up to two million people. The project was constructed by a joint venture (JV) of four South American contractors and consisted of the following key components:• Treatment plant: A 16-ha (39-acre) area was cleared for the construction of a treatment plant to purify 900,000 m3/day (1.2 million cu ft/d) of raw water from the Paraná River and distribute it to the surrounding communities.• Bored tunnel: Nearly 15 km (9 miles) of 3.6 m (12 ft) inner diameter tunnel, ranging from 18 to 22 m (59 ft to 72 ft) below grade, was bored with two earth pressure balance (EPB) tunnel boring machines (TBM) to draw the raw water from the river. The TBMs started from a central launch shaft and proceeded in opposite directions. Cristina advanced northbound to the Paraná River Intake System, and Liliana advanced southbound to the new treatment plant.• Access and ventilation shafts: Five access shafts and eight ventilation shafts were installed along the length of the tunnel. The access shafts were designed to provide entry points for inspection and maintenance of the final tunnel. The five shafts consisted of one central launch shaft in the middle of the tunnel alignment, one retrieval shaft at each end of the tunnel (intake and treatment plant, respectively) and two intermediate shafts. The intermediate shafts were installed before the TBM passed, with a final liner to be installedafterward."

Sep 1, 2016

By Otto L. Schumacher

The Overthrust Belt in portions of Montana, Idaho, Utah, and Wyoming, an area that has contributed generously to the Nation's mineral supply, is one of the few remaining oil and gas frontiers on the North American continent. Determination of the oil and gas potential and development of mineral resources of the area have been affected by a variety of land withdrawals and other restrictions, The purpose of this study is to determine the extent of these withdrawals and restrictions and to discuss the mineral resource potential within the study area. Statistics in this report refer to land status on January 1, 1979. At that time, of the 27.3 million acres of Federal mineral lands within the study area, applications tor Federal oil and gas leases for more than 4,4 million acres (about 16 percent) were pending; the average length of time was 2 years. Federal oil and gas leases covering 8.8 million acres were also on record. Although drilling has occurred on some of these leases, others are subject to restrictions that discourage or prevent development. Some in fact contain stipulations disallowing any development.

Jan 1, 1981

By E. A. van Dijk

Dusts from steel-making processes contain substantial amounts of zinc. Such dusts are also a hazardous waste and dumping them becomes unacceptable from environmental point of view. Therefore processes that can recover zinc and possibly other metals from steel-making dusts are being investigated. The aim of this paper is a contribution to the more fundamental kinetic aspects of zinc reduction from silica free calcium ferrite slags. The effects of alumina, lime and magnesium oxide contents of the slag, the COICO, ratio and the effect of initial Fe2O3/CaO ratio were studied experimentally at 1400°C The results indicated that the reduction of zinc from molten slag was possibly a first order reaction. As expected higher COICO, ratios increased both the extent and the rate of reduction. It was also observed that a higher iron content of slag improved the reduction of zinc from calcium ferrite slags. This fact seems to support the proposed mechanism that zinc is partly reduced by ferrous iron to zinc vapour and that ferric iron is reduced by carbon monoxide. The reduction rate of zinc in these slags was decreased by increasing alumina content of the slag. Alumina decreased the calculated optical basicity of the slag showing the fact that reduction of zinc oxide was more favorable in more basic slags. Probably the formation of complex ions by alumina and zinc oxide such as ZnAl2O32+ lowers the activity of Zn2+ ions in the slag and hence render them more difficult to reduce.

Jan 1, 1999

By Laurence G. Britton

Accurate flammability and ignitability data for chemicals form the cornerstone of procedures used to assess the hazards associated with commercial chemical production and use. Since 1967 the ASTM E27 Committee on the Hazard Potential of Chemicals has issued numerous, widely used consensus standards dealing with diverse testing and predictive procedures used to obtain relevant chemical hazard properties. The decision to issue a standard rests solely with the membership, which consists of representatives from industry, testing laboratories, consulting firms, government, academia, and instrument suppliers. Consequently, the procedures are automatically relevant, timely, and widely applicable. The purpose of this paper is to highlight some of the widely used standards, complemented with hypothetical but relevant examples describing the testing strategy, interpretation, and application of the results. A further goal of this paper is to encourage participation in the consensus standards development process. The paper is published in two parts. The first part (in the preceding issue of Process Safety Progress) dealt with the E27 standards pertaining to thermodynamics, thermal stability, and chemical compatibility. The second part, published here, focuses on the flammability, ignitability, and explosibility of fuel and air mixtures. © 2005 American Institute of Chemical Engineers Process Saf Prog 24: 12?28, 2005

Jan 1, 2005

By R. Lanza, M. Hytros, N. Saka, I. Jureidini, J. H. Chun, D. Kim

"A novel method for delineating the solidification front in metal casting has been developed using the attenuation phenomenon of electromagnetic radiation (y-rays or x-rays) and computed tomography (CT). The densities of the liquid and solid phases that exist during metal casting may differ anywhere from 4 to 12 % depending on the metal. As in the medical imaging field, CT provides an excellent means of mapping this density variation in a solidifying casting into two-or three-dimensional images.In an effort to develop an industrial-scale sensor, laboratory-scale experiments have been conducted using a cobalt-60 (Co60) radioisotope and a sodium-iodide (Nal) scintillation detector. The CT image reconstruction was performed on a crucible containing pure tin in a two-phase state. Although the spatial resolution and data acquisition speed were not optimum, the CT images clearly differentiate the liquid and solid phases of the tin in the crucible. To maximize resolution and minimize data acquisition time, a linear accelerator (linac)-based CT sensor is being developed and tested for application in the continuous casting of steel and aluminum alloys.IntroductionIn all casting processes, the quality of a finished product and its production rate depend upon the shape and movement of the solidification front. From a quality perspective, it is well documented that solidification kinetics (heat and mass transfer, fluid flow, microstructure evolution) greatly influence the final properties of castings [l,2,3]. Product shortcomings, such as surface defects, cracks, macro-and microsegregation, and inclusions are directly controlled by the solidification process. By understanding the role the solidification front plays in the casting process, product quality may be dramatically increased through the reduction of defects."

Jan 1, 1997

By Robert Stefanko

The importance of underground stress instrumentation cannot be minimized. It was Lord Kelvin who said that unless you can assign a number to a quantity,, you know very little about it. Most engineers will agree although this kind of statement is resented by our friends in non-technical fields. Mining is undergoing a revolution from art to science. But how can mining methods be optimized if there is no way of measuring the effectiveness of a given mining method? Do we know how effective a' support is unless we can determine its reaction to the mine structure? How do we assess the need for modifications to existing systems and supports, and how do we measure the effectiveness of such changes? Cut and try techniques are too wasteful of time and energy, and rarely provide solutions to a given problem. The purpose of underground stress instrumentation is to provide answers to some of the above questions -- answers that cannot be obtained otherwise This does not mean that laboratory studies are not valuable -on the contrary. Laboratory and underground studies supplement one another. Rock mechanics had its conception with the study of stresses in homogeneous, isotropic, and elastic models subjected to various force systems. These analyses were valuable inasmuch as they pinpointed possible sources of trouble due to stress concentrations. If the results observed underground did not always agree with the experimental analysis, it was not an indictment of the latter. More probably, the discrepancy could be attributed to the lack of similitude between model and prototype. The more nearly one can simulate underground conditions in a model, the more apt one is to produce results which correlate well-with underground observations. It is impossible to completely simulate underground conditions because all of the significant design parameters have not been recognized and evaluated. What better way can one evaluate these parameters than by underground stress instrumentation?

Jan 1, 1963

By Gjergj Dodbiba, Toyohisa Fujita, Li Pang Wang, Masashi Yamane

"The platinum-group metals (PGMs), are currently receiving worldwide attention as they have major industrial uses. PGMs, i.e. ruthenium (Ru), rhodium (Rh), palladium (Pd), osmium (Os), iridium (Ir), and platinum (Pt), are widely used as catalysts in petroleum and chemical processes. In addition, they find wide applications in automotive exhaust-gas control converters and are of immense importance to the electronic industry. Broadly speaking, PGMs are extracted in minute quantities from a limited number of ores, found mainly in South Africa and Russia. As the PGMs are both costly and almost indestructible, they are usually recycled from various forms of scrap. In other words, the recycling of the PGMs is an essential factor in the overall management of the PGM economy. In addition, the ever-increasing user areas have created renewed interest in the search for new sources or deposits of PGM, which in turn requires an in-depth knowledge of its characteristics. In this work, the emphasis is placed on the need to analyze the composition and microstructure of blast-furnace slag for recovering PGM metals. In other words, chemical composition, surface analysis and microstructure analysis of the DC arc furnace slag have been carries out. The aim is to provide a detailed analysis of this material for anyone with an interest in gaining further knowledge of its specific content for recovering PGMs."

Jan 1, 2014

By Qiu Dingfan

The Slurry Electrowinning Process (SEP) is a new hydrometallurgical method and clean technology, Sulfide ores can be treated by the SEP without S02 emission and the sulfur from the sulfides can be recovered in element form which is easy to stockpile and can be transported at low cost. In a special slurry electrowinning cell one can achieve at the same time the leaching of elements from the feed and the electrowinning of metals from the electrolyte, Because the anode reactions are utilized for leaching of some elements the consumption of the energy is decreased, SEP also has the advantage of separation some elements, It is especially suitable for treatment of complex concentrates containing Pb, Cu, Au, Ag and S, which could hardly be accepted by any smelter. In this work, the behavior of different metals in this process has been studied and it was found that the separation of metals in some minerals is possible through the SEP, Beijing General Research Institute of Mining and Metallurgy (BGRIMM) has studied the possibility of the SEP to treat bismuth concentrates containing S, Be and F in laboratory and pilot-test scale as well as in commercial plants, The commercial plant was set up in 1997, It has been in operation since that time, According to the results of laboratory experiments and pilot- plant test, a new plant to treat complex gold minerals was set up in 1998 and is in operation in 1999

Jan 1, 2003

By R. V. Ramani, A. S. C. Owili-eger

A mass balance equation can be written for the unit block of Figure 7 for changes within the volume during time At as: [ ] where x and y are the coordinates; q is the flow across any surface; p is the density of the fluid flowing through the medium; qvol is the volumetric flowrate; @ is the medium porosity; and Ax and Ay are the dimensions of the block. The subscripts t and (t+At) denote time levels and At is the change in time. Writing this equation in nota- tional form and on rearranging, the following expression is obtained:

Jan 1, 1974