Search Documents

By Yong-Moo Cheong

When the zirconium pressure tube(PT) is in contact with the calandria tube(CT) in the pressurized heavy water reactor(PHWR), the temperature gradient between the inner and outer wall of the PT results in a thermal diffusion of hydrogen(deuterium) and hydride blisters are formed on the outer surface of the PT. Since Zr-2.5Nb pressure tubes have a high risk for the formation of blisters during their operation in a PHWR, there is a strong incentive to develop a method for the non-destructive detection of the blisters grown on the tube surfaces. However, because there is little mismatch in an acoustic impedance between the hydride blisters and zirconium matrix, it is not easy to distinguish the boundary between the blister and the zirconium matrix with the conventional ultrasonic methods. This study has focused on the development of an ultrasonic method to detect the hydride blisters formed on Zr-2.5Nb pressure tubes. Hydride blisters were grown on the outer surface of a Zr-2.5Nb pressure tube using a cold finger attached to steady state thermal diffusion equipment. Ultrasonic velocity ratio method as well as conventional ultrasonic parameters with an immersion technique was developed to detect small hydride blisters on the Zr-2.5Nb pressure tubes.

Jan 1, 2006

By Frédéric Flament

The aim of this paper is to present the development of a data validation software as component of a commercial mass balance package. Data reconciliation through mass balance is basically an optimization problem constrained by the law of mass conservation. As any optimization problem solved with a modern and robust software application, erroneous information or starting point will always lead to a solution, whether it is realistic or not. Moreover, good information wrongly weighted by an incorrect error model will lead to the same bad ending. In an industrial context where competition requires accurate information, data reconciliation without validation can be disastrous and calls for data validation before and after reconciliation. The challenge in automated data validation resides in the development of general theoretical solutions. Until now, none has been presented and only partial solutions are available. The development presented in this paper incorporates some of these partial solutions. The integration of human knowledge into the application paved the way to a more general solution. The combination ?theoretical validation ? human expertise? proved to be flexible and reliable enough to be integrated in a commercial data validation package. Numerous examples though industrial applications are presented. These applications demonstrate the validation of raw measurements, user support in the development of error models and validation of reconciled measurements.

May 1, 2001

By R. L. Virta

Ball Clay -- Four companies - H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Imerys Group (formerly Kentucky-Tennessee Clay Co.), Old Hickory Clay Co. and Unimin Corp. - mined ball clay in four states during 2010. Production, based on preliminary data, was 910 kt (1.11 million st) with an estimated value of $42.9 million. That was a 10-percent increase in tonnage from 831 kt (916 million st) with a value of $37.7 million that was produced in 2009. Tennessee was the leading producer state with 61 percent of domestic production. It was followed by Texas, Mississippi and Kentucky. About 70 percent of production was airfloat, 20 percent was crude and 10 percent was water-slurried.

Jan 1, 2011

By Mildred Nadler, Alvin Kaufman

To aid industry and Government in planning water developments the Bureau of Mines in 1963 canvassed mineral producers to determine water use in 1962. Water use by the mineral industry comprises only 2 percent of the water withdrawn by industry as a whole. The major water-using mineral industries are natural gas processing, phosphate rock, sand and gravel, and iron ore. Analysis indicated the following conclusions: 1. Total water use and new water intake is dependent on the quantity of material processed and the process water requirements of the particular indus- try or commodity. 2. Recirculation is dependent on the processing requirements of a par- ticular commodity, the manner in which the water is used, cooling and condens- ing requirements in certain large industries, the quality of new water intake, and the need to treat new and discharged water. 3. Consumed water is dependent on the quantity of water recirculated, the temperature and humidity in the area, and the proportion of water used for cooling and condensing. 4. A threefold increase in water use by the mineral industry by 1985 is forecast.

May 1, 1965

By Oliver C. Ralston, Dorsey A. Lyon

The data reported in this bulletin are largely the result of experiments conducted by the Salt Lake City station of the Bureau of Mines in cooperation with the department of metallurgical research of the University of Utah. The work on lead is only one of the phases of the investigations carried on at that station during the years 1914 to 1916. The results of similar work with zinc ores and with copper and other ores will be published in future reports of the bureau.

Jan 1, 1918

Discussion, at the Virginia Beach Meeting, February, 1894, of the Paper of Prof. Posepny. (Trans., xxiii., 197, 587.) Including communications subsequently received. a T. A. Rickard, Denver, Colorado (communication to the Secretary) : The paper of Professor Posepny was printed so short a time

Jan 1, 1895

By D Bradshaw, J R. R de Villiers

The non-stoichiometric sulfide mineral pyrrhotite (Fe(1-x)S), common to many nickel and platinum group element (PGE) ore deposits, occurs in varying crystallographic forms with the different types exhibiting subtly different physical and chemical properties. These differing properties are likely to influence the flotation performance of pyrrhotite, which in the case of PGE operations is actively recovered, whereas in nickel operations pyrrhotite is depressed. In this study, examination of natural pyrrhotite samples from Southern African and Canadian nickel and PGE ore deposits revealed a variety of pyrrhotite compositions in terms of iron content (Fe7S8, Fe9S10, Fe11S12) and solid solution nickel concentration. Pyrrhotite composition was correlated with its mineral association depending on whether non-magnetic pyrrhotite occurred in conjunction with troilite, non-magnetic pyrrhotite occurred as single phase pyrrhotite, magnetic pyrrhotite occurred as single phase pyrrhotite or whether the two phases; magnetic and non-magnetic pyrrhotite co-exist. Subsequent microflotation tests of selected single phase pyrrhotite samples revealed that the non-magnetic pyrrhotite is slightly more floatable than magnetic pyrrhotite. Microflotation tests also showed that varying flotation responses occur between differing magnetic pyrrhotite samples. These differences in flotation performance are postulated to be a result of the effects of varying pyrrhotite crystallography, trace metal content and mineral association on pyrrhotite oxidation, formation of surface species and subsequent adsorption with xanthate collector.

Jan 1, 2008

By Herty, C. H.

Present-day interest in the question of "dirty steel" has arisen primarily from the increasingly rigid specifications on various grades of steel and from the growing conviction that non-metallic inclusions are the source of many of the difficulties in meeting these specifications. The importance of inclusions has unquestionably been over-emphasized in many cases, but on the other hand many unpublished instances could be recorded where all evidence pointed to inclusions as the primary cause for the failure of steel in rolling or in service. The solution of the problem of dirty steel is not a matter of a few years. There are almost numberless types of inclusions. They segregate in steel ingots in an entirely different manner from other impurities, and, at best, only a start has been made in developing correct analytical methods for their determination. Most of the writers in the field have expressed opinions rather than given facts, and so many variables enter into the manufacture of steel that a study of plant conditions is difficult unless definite facts on certain phases of the inclusion problem are available. This statement is not intended to convey the idea that little work has been done on this problem. On the other hand, the number of investigations has been large, but in most cases too many variables have been present to allow definite conclusions to be drawn. In the body of the text, reference to previous investigations is made at suitable points. Rather than burden the reader with a lengthy review of the literature on the general subject of inclusions, reference to the particular works pertinent to the subject matter of the bulletin has been discussed. Three excellent bibliographies b on the subject have been lately published: one by the Committee on

Jan 1, 1957

By H. C. Boydell

Those connected with mining, prospecting, or mining geology in northern Ontario are familiar with the fact that it is a comparatively unusual thing to have assayed a sample for which the assay report shows no gold. Values of 20 cents to 80 cents per ton, or even higher, are extremely common. Whilst contamination by fluxes, faulty manipulation, or a desire, on the part of the assayer, to sugar-coat the pill for the client, may account for 20 to 40 cent values at times, it is un1ikely that they would a1ways do so. Exonerating the assayer from being necessarily at fault, what can be the cause of such a widespread distribution of gold (and silver) in minute quantities- of a dissemination .that, in the writer's experience, and so far as he is? aware, is not met with on a simi1ar scale in other parts of the world? Explanations that suggest themselves are, that the dissemination is due: 1. To a very widespread auriferous minera1ization, post-dating (epigenetic) the formation of the rocks in which it occurs. 2. To a general syngenetic distribution of gold in the volcanic rocks of Keewatin age that form so large a part of the sections of northern Ontario that have been prospected.

Jan 1, 1928

By D. A. Beattie

Talc is a commonly encountered gangue mineral in metal sulfide flotation. Talc is naturally hydrophobic, resulting in high recoveries if polymeric depressants are not used to specifically reject this MgO containing mineral. We have studied the adsorption of a selection of polymers onto talc using a variety of techniques. Adsorption isotherms have been determined using ex situ depletion techniques and in situ ATR-FTIR spectroscopy has been used to determine adsorption kinetics. Adsorbed layer thicknesses have been determined for the polymers on cleaved talc surfaces using the AFM. The effect of the adsorbed polymer layer on the properties of the talc surface has been quantified through contact angle measurements and single mineral flotation tests. Distinct correlations are observed between the adsorbed layer properties and the flotation performance of the polymers. These observations are discussed with reference to the bubble-particle attachment process and the molecular structure of the polymers.

Jan 1, 2006

By Avijit Moitra

The behavior of the solidifying shell in the early stages of solidification has an important influence on the final quality of continuously-cast steel slabs. In order to understand the thermal and mechanical behavior of the shell, a two-dimensional transient piecewise-coupled finite-element model has been developed. The model simulates a transverse section of the slab as it moves down through the mold and incorporates the effects of heat conduction, solidification, shrinkage, turbulent fluid flow, thermal distortion of the mold and the visco-plastic behavior of the steel. Coupling between the thermal and the mechanical model is based on the mutual dependence of heat transfer across the interface between the shell and the mold and the size of the gap. The effects of mold distortion and taper on the gap size are also included. The effect of fluid flow has been incorporated via a heat flux imposed at the solid-liquid interface, which is obtained from a separate fluid flow model. The high temperature creep and plasticity of the steel is incorporated through a unified constitutive law defining the inelastic strain rates as a function of temperature, time and stress state. The model can be applied to various problems in continuous casting, such as the formation of surface defects and the design of mold taper.

Jan 1, 1992

By Patrice Chartrand, Halvor Dalaker, Philippe Ouzilleau

A size-dependant thermodynamical model for the carbon-hydrogen previously developed by Ouzilleau et al. [1] has been expanded here to include chemisorption of methyl groups. Gibbsenergy minimalisation calculations using FACTSAGE software on this model indicates that hydrogen bonding through methyl groups is energetically favoured as an intermediate between bonding as monoatomic hydrogen to edge hexagons (which is more favourable) and as monoatomic hydrogen to corner hexagons (which is less favourable). The model has also been applied to methane decomposition and oxide reduction using natural gas. A C-H solid solution as a thermodynamic description of the solid carbon phase influences calculations of carbon activity in metastable methane, and gives different results than when using graphite.

Jan 1, 2015

By Alper Kirmaci, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Injuries and fatalities resulting from roof falls are still a major concern in U.S. coal mines, and many researchers are focused on developing meaningful approaches to minimize this hazard. In the United States, coal mine roofs can vary widely in composition, geometry, and inherent heterogeneity, leading to a wide array of different roof fall failure types. Researchers frequently employ numerical modeling tools to reproduce this physical phenomenon and provide key guides to engineers regarding roof conditions and control as long as the input data and constitutive relations are appropriately selected. Simulating such complexity requires expertise and constitutive models that adequately simulate roof behaviors. However, the currently available constitutive models have shortcomings in capturing some of the roof fall failure types common in underground coal mines, such as guttering. A new constitutive model is developed to address the shortcomings of constitutive models commonly used for coal roof stability analysis. The constitutive model developed in this study combines the anisotropic-elasticity and nonlinear strain-softening responses. In addition, the developed constitutive model can simulate up to three different joint sets implicitly, allowing for use in both continuum and discontinuum settings, and can be used in both Lagrangian finite-volume and distinct element method codes of Itasca. First, the mathematical expressions of the model are provided. Afterward, the validation phase of the developed model that covers comparisons with analytical solutions and those of existing models (e.g., anisotropic elasticity, ubiquitous-joint, and bilinear strain-hardening/softening ubiquitous-joint plasticity) is presented. Finally, a hypothetical coal mine roadway facing high horizontal stress is simulated. The presented model successfully shows three distinct stages of a cutter roof in a shale roof: (1) initiation of shear cracks at the rib– roof intersection, (2) extension of cracks deeper into the roof (i.e., above the roof bolt length horizon), and (3) cantilevered roof. It is demonstrated that the presented constitutive model has the potential to help future researchers in simulating various roof responses.

Jul 1, 2023

Gas-liquid contacting in the packed bed is a common operation in metallurgical reactors. Research has shown that, unlike wetting flow, non-wetting liquid flows in the form of discrete droplets or rivulets. Thus, modeling of the liquid phase as a continuum is in contradiction to the observations. Also, for the non-wetting case, continuum models have failed to describe liquid flow path when the liquid source is a point source. The aim of the current work is to put forward a combined Lagrangian-Eulerian approach to model the liquid and gas flow in the packed bed. Liquid is assumed discrete and modeled using a force balance approach. Gas is assumed to be interpenetrating continua and modeled using k-emodel for turbulent flow. Structured packing is assumed and x- ray imaging technique is used to visualize liquid flow lines in the bed. Simulation results for liquid flow path compared with the experiments.

Jan 1, 2006

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage arc also described. IntroductionThe association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate ·formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation.In its most general form, the process of agglomeration involves taking discrete, independent particles, bringing them into contact with one another, promoting (or allowing) interparticle adhesion to occur and then causing structure rearrangement, usually under the action of external forces. The relative importance of these steps varies with the nature of the particulate system being agglomerated and with the kinds of agglomerates being produced. Coagulation or flocculation of particles dispersed in fluids is generally dominated by the contact and adhesion steps. In the granulation of powders, on the other hand, particles are already in contact so that structure rearrangement is the principal step."

Mar 1, 1992

By I-H. Jung, J. Kim

"Mg alloys are extensively used as light structural materials in modern industry. Mn and RE (rareearth) metals are effectively used as alloying elements to enhance the properties of Mg alloys. Therefore, the thermodynamic database of those alloys is important in the Mg alloy design and processing. Critical evaluation and optimization of all available literature data for the Mn-RE systems were conducted to obtain reliable thermodynamic functions. The Mn-RE systems shows systematic changes in the phase diagrams and thermodynamic properties with increasing atomic number in the lanthanide series. This systematic approach for all RE elements allows to resolve inconsistencies in the available experimental data. INTRODUCTIONRare Earth (RE) metals are widely used in many industrial fields including permanent magnet, electronic materials and structural materials. As a small addition of RE can enhance magnetic, electronic, optical and mechanical properties of numerous materials, the usage of the RE is still expanding regardless of the strategic control of their supply.Magnesium alloys are getting great scientific and industrial attention as the lightest structural materials. One of the drawbacks of Mg alloys is their poor formability at room temperature due to the limited slip system with hcp crystal structure. Recently, several studies (Farzadfar et al., 2011; Sandloebes et al., 2010; Stanford, 2010; Stanford et al., 2008; Yan et al., 2010) show that the additions of small amounts of RE can considerably enhance the ductility of Mg alloys. Therefore, a lot of research on Mg-RE alloys is undergoing to clarify the role of RE on the enhanced deformation mechanism and to find out the most optimum Mg alloy compositions. In order to respond to the need of Mg-RE alloy development, a large thermodynamic database for Mg alloys containing RE has been developed with critical systematic analysis and optimization of the entire RE series data. This includes the thermodynamic database of the Mg-RE (Kang et al., 2009), Mg-RE-RE (Kang et al., 2009), Mg-Al-RE (Jin et al., 2011; Jin et al., 2010), Mg-Zn-RE and Mg-Mn-RE systems."

Jan 1, 2012

By Michael Zinigrad

The quality of metallic materials depends on their composition and structure and these are determined by various physico-chemical and technological factors. To effectively prepare materials with required composition, structure and properties it is necessary to carry out a research in two parallel directions: Comprehensive analysis of thennodynamics, kineties and mechanisms of the processes taking place at the solid-liquid-gaseous phase interface during welding processes and development of mathematical models of the specific welding technologies. We have developed unique method of mathematical modeling of phase interaction at high temperatures. This method allows us to build models taking into account the thennodynamic characteristics of the processes, the influence of the initial composition and temperature on the equilibrium state of the reactions, the kinetics of heterogeneous processes, the influence of the temperature, composition, hydrodynamic and thennal factors on the velocity of the chemical and diffusion processes. The model can be implemented in the optimization of various technological processes in welding, surfacing, casting as well as in manufacturing of steels and non-ferrous alloys, materials refining, alloying with special additives, removing of non-metallic inclusions.

Jan 1, 2003

By J. C. Wilmot

The chemistry of aqueous cyanide containing species in the presence of reduced sulfur sources was investigated. Reactions were studied as a function of time and tracked using novel analytical techniques developed for the analysis of the species of interest in the sample matrix. Species of interest in this work were ?free? cyanide, thiocyanate, cyanate, metallo-complexed cyanide, and various sulfur and sulfur-oxygen species. The studies were conducted under constant temperature conditions at pH values above 10.5 and in the absence of light in order to eliminate photochemically induced cyanide reaction effects. The reaction products of cyanide when in contact with pure sulfur, pyrite, pyrrhotite, sphalerite, and cinnabar are reported. These data combined with data for cop-per, arsenic and lead sulfides, which have been previously published, are used to predict the fate of cyanides in refractory gold ores containing sulfides. A mass balance on the cyanide reaction products was completed for all experiments. From these studies insight into the chemical relationships of cyanide, the specific metal sulfide, thiocyanate and cyanate have been gained. When looking at the results of the experiments, it was immediately apparent that even though the overall conversions of cyanide to thiocyanate were different, most of the samples exhibited a similar pattern of reactions. The recovery of cyanide in these experiments was better than we expected, averaging in most experiments to be over 90 percent. Based on this research, the formation of cyanate was probably the main route of loss. The pathway choice for the various minerals was also elucidated in these experiments. The competitive oxidation pathways that cyanide can take have been tracked for sufficient time to determine the ?final? fate of cyanide in a process. Initially, it was thought that the cyanate may be involved in a hydrolysis reaction to form ammo-nia and carbonate ion, but upon further inspection of the data, there was not the drop-off in total cyanide recovery that would manifest itself were this to happen. On the other hand, the hydrolysis of thiocyanate to cyanate and sulfate would require oxidizing conditions which did not exist in solution at the beginning of the experiment. If the solutions were to be sufficiently oxidizing in nature for this to happen, the initial amount of cyanide would have been converted to cyanate quickly. The data support premise that the ?hydrolysis? of thiocyanate to cyanate and sulfate occurs to some extent in the experiments conducted. Knowledge gained from the experiments with pure metal sulfides helped interpret the results of experiments with refractory ores found in the State of Nevada.

Jan 1, 2014

By S. P. Lowe

Introduction In the following pages a general description is presented of the concentrator and cyanide plant of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, together with some account of the steps which have led to the adoption of the present practice. For an account of the preliminary test-work and pilot-mill operation, the reader is referred to a recent paper by R. E. Phelan on the History of Flin Flon Mine up to Construction (1). Additional notes may be found in a paper which the writer presented at the Annual Meeting of the Institute in 1930 (2). The first ore was crushed in the present plant on July 1st, 1930, and the first ball-mill was started one month later, on August 1st. Since that time, production has been continuous with the exception of one month lost during a strike in the summer of 1934. There have been no major changes in equipment or methods of treatment since the present plant was built, but many minor changes have contributed to the improvement in results obtained and to the increase in capacity to the large tonnage now being milled. The accompanying flow-sheets indicate the equipment used in the several plants, with the average life and repair cost. As originally built, the concentrator was to treat 3,000 tons per day, but the capacity has been increased to 4,400 tons. The methods adopted to make possible this increase in tonnage will be referred to below. It was the intention to produce two classes of ore: (1) a heavy sulphide, and (2) a disseminated ore. The mill was consequently divided into two sections, each adapted for most efficient treatment of one particular type of ore. However, it was soon found that it would be impossible to mine the two classes of ore separately, so it was decided to treat open-pit ore, which varies greatly in character, in the sulphide section, and underground ore, which is fairly constant, in the disseminated section. This segregation is still maintained.

Jan 1, 1935

By N Haque, S Northey

Water in mining, mineral processing and metal production on a life cycle basis has been at the top of agendas for various industries, government agencies, research organisations, academic institutions and communities. As a result, a number of water footprint assessment methodologies have been developed. However, their practical applications in mining and mineral processing industries with specific case studies are still rare.A key objective of the Minerals Down Under Flagship is to contribute to the long-term sustainability of the Australian mining and mineral industries. Researchers in the Mineral Futures theme have developed robust assessment methods to evaluate the impact of mining and minerals technology development on the environment. The future of mining and the mineral industry is strongly linked with its sustainability - better water management strategies will need to be implemented.Life cycle assessment (LCA) has been a recognised method for measuring the environmental impacts of products, processes and services. It provides a scientifically sound method of comparing products and processes using a common basis and identifies so called æhot spotsÆ and opportunities for reducing environmental impacts. The water footprint of mining, mineral processing and metal production using an LCA basis is still scarce in the literature. Research methodology is now being applied in detail for copper, gold and nickel. A primary focus has been the relationship between ore grade and water use for which mathematical models are being developed. These types of models provide inputs for LCA of mining and mineral processing plants and can identify water saving opportunities through scenarios and process route analysis.CITATION:Northey, S and Haque, N, 2013. Life cycle based water footprints of selected mineral and metal processing routes, in Proceedings Water in Mining 2013 , pp 35-50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013