Search Documents

By Paul E. Rosten

This paper describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Company to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Company operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and Western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes .each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously. (1) (2)(3) Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and furnished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate-kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1977

By B. Mishra, Q. Shi

Numerical simulations have been used to investigate roof fall in the past decades. Comparing to the continuum based methods, the discrete element method has been well recognized for its excellent performance in simulating large strain problems and fracturing processes in the rock mass. However, the discrete element method has its limitations. When simulating a large-scale problem, a large number of particles are required, which consumes significant computational resources. In the present study, a 3D numerical model coupled with the finite-difference method (FDM) and the discreteelement method (DEM) was created to simulate the laminated roof failure in an eastern coal mine in the US. In the FDM-DEM coupled model, the laminated roof of the entry is represented by an assembly of bonded particles using PFC3D. The laminated roof is simulated by adding parallel discontinuities. The discontinuities are given certain stiffness and strength in the model. The ribs, floor, and far-field surrounding rock are represented by continuum zones using FLAC3D. The strength of the discontinuities is varied sequentially and the fracturing of the laminated roof was analyzed with respect to entry advance. The results showed that the laminated roof fractures along the discontinuities while an intact roof fractures in a dome shape. Increasing the strength of discontinuity could enlarge the tensile zone inside the laminated roof and hence change the crack distribution. In addition, the crack quantity in the laminated roof behind the advancing face decreases with the increment of discontinuity strength while this trend is not occurring ahead of the advancing face. The simulation demonstrated that coupled method using PFC3D/FLAC3D can reproduce the laminated roof failure in underground coal mines.

Mar 2, 2022

By E. Mokgwamme, T. Goff, M. Mvalelwa, P. Spratt, P. Bezuidenhout, P. Nkosi, H. Joubert, G. de Villiers

Sibanye-Stillwater recently completed a partial sidewall rebuild on Furnace 1 at its Marikana smelter complex. The project involved matte taphole maintenance, which required the removal and subsequent replacement of 18 composite copper-graphite coolers and a section of the lower refractory sidewall. These composite copper-graphite coolers are a newly developed cooling design by Tenova Pyromet, and this rebuild project provided valuable insight into the performance of the composite coolers. The novel composite cooler design was implemented to serve as a safeguard against localised wear and corrosion in the furnace sidewall, particularly at the slag-concentrate interface, where chloride-accelerated sulphidation has been identified as a dominant degradation mechanism affecting the copper cooling elements. The composite cooler design is unique in that all the exposed sides of the water-cooled copper elements are fully encapsulated in graphite, which protects the copper from corrosive sulphur- and chlorinebearing gases and condensates. This sidewall cooling system was designed to improve corrosion resistance, stabilise freeze lining formation, and extend the campaign life of the furnace sidewall. The partial sidewall rebuild was executed during a planned maintenance shutdown with the main objective of replacing the matte taphole lintel bricks. This paper serves as a case study that compares and evaluates the operational performance of the composite coolers before and after the rebuild. The installation method is discussed to highlight the approach taken to ensure a sound installation while minimising downtime, as well as to present some lessons learned in the process.

Mar 6, 2026

By T. Ivankina, T. Lokajícek, H. Kern, T. Svitek

The knowledge of 3D velocity distribution of P- and S-waves in rocks is very important parameter for interpretation and understanding the nature of seismic anisotropy observed in the earth’s crust and upper mantle. A new high-pressure measuring head was designed and constructed to enable ultrasonic sounding of spherical rock samples in 132 independent directions under up to 60 MPa of acting hydrostatic pressure by means of simultaneous longitudinal and transversal sounding. New measuring system enables ultrasonic sounding of spherical rock samples by using a pair of P-wave sensors and two pairs of perpendicularly polarized S-wave sensors (TV and TH) see Fig.1. Shear wave sensors polarization is oriented according to rotation axis of the sample. Special shear wave gel was used to transfer shear waves between the sample and sensors under acting hydrostatic pressure. An isotropic glass sphere was used to check and calibrate the new measuring setup. A spherical sample of a biotite gneiss from the Outokumpu scientific drill hole was used for testing measurement. There is shown that both, P- and S-wave velocities, can be measured simultaneously up to 70 MPa, respectively. We report data of the 3D velocity distribution of P- and Swaves measured for the first time on a sample sphere of biotite gneiss. We rely, in particular, on the directional dependence of compressional and shear wave propagation and their relationship to the crystallographic (CPO) and shape preferred orientation (SPO) of major rock-forming minerals. The 3D seismic measurements revealed a strong foliation-related directional dependence (anisotropy) of P- and Swave velocities. Ultrasonic measurements were compared with 3D velocity calculations based on neutron diffraction measurements of crystallographic preferred orientation (CPO) of major minerals. Comparison of 3-D velocity distribution (P, S1, S2 and S1-S2) determined by two completely different methods ultrasonic sounding and neutron diffraction is presented. Measurements showed that the intrinsic bulk anisotropy is basically caused by the CPO of biotite constituting about 23 vol.% of the rock.

Jan 1, 2015

By P Duplancic and C R Lilley, R Hudson, D Beck

For deep block and panel caving mines, undercut or extraction level instability can have as much impact on overall recovery as underbreak or the premature ingress of waste. If the area of the mine affected by excessive convergence is small, recovery is usually possible. However, there are several examples of entire blocks that were abandoned prematurely due to footprint collapse. Clearly, such global instability has a major impact on recovery and must be avoided – this is one of the essential tasks for the design team.The design problem is complex. The planning engineer must ensure that the footprint has sufficient capacity to withstand the maturing loads in the cave, accounting for the effects of stress path, geological structures and the rock mass conditions. These are often uncertain and only sometimes quantified.The demand on the footprint will also be influenced by decisions and actions taken during production, especially related to draw, which can worsen a developing problem. Perhaps most importantly, the design decisions that favour stability and lead to lower deformation also negatively impact on idealised cave flow. Many engineers aim to minimise the size of extraction level pillars, to improve theoretical future resource recovery but in fact this can reduce recovery if widespread deformation ensues due to the undersized pillars.In 2014, PT Freeport Indonesia undertook detailed numerical analysis to quantify the effects of variability in rock mass conditions and geological structure on overall footprint performance. The analysis accounted for a range of stress paths and maturing cave loading scenarios sourced from a calibrated whole-of-cave deformation-flow model. The intent was to replicate some of the diversity and distribution of pillar deformation outcomes that may be seen in practice at Freeport.The discontinuum finite element analysis was able to replicate damage localisation around persistent structures, a realistic distribution of drive deformation and show how small areas of instability can evolve into major problems if poorly managed. The limits of pillar size and ground support as solutions to a number of different instability problems was also investigated, showing that pillar size alone was not a sufficient remedy for all adverse circumstances.In this paper, we describe the workflow for numerical analysis of footprint deformation. We discuss the compromises and considerations for balancing the sometimes competing needs for efficient extraction levels pillars, ground support and prudent draw strategy.CITATION:Beck, D, Hudson, R, Wilson, A D, Duplancic, P and Lilley, C R, 2016. An investigation of factors affecting the long-term reliability of extraction level pillars in deep block and panel caves, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By C. M. Bouton

Although much valuable work has been done in the study of dust explosions, the laboratory technique has not been developed to the point where the many factors involved can be properly controlled, and thus where really fundamental information can be obtained. This paper presents a brief discussion of the difficulties encountered in fundamental work on dust explosions, a description of apparatus intended, to overcome some of them, and an account of some results obtained. FACTORS INVOLVED IN DUST EXPLOSIONS The more important factors pertaining to the dust cloud itself which are known to determine the phenomena of explosions are (1) the kind of dust; (2) its fineness; (3) its concentration in the exploding cloud; and (4) the nature of the interior motions, or turbulence, of the cloud before and during the explosion. These factors are arranged in what seems to be an ascending order of complexity. The kind of dust is the factor most easily subject to control. The fineness of the dust at first sight seems to be a controllable factor, but when it is recalled [that] most explosible dusts are mixtures of particles of continuously varying sizes so small as to pass through the finest woven sieves, and therefore difficult to separate either for purposes of analysis or experiment, the fineness is seen to be a factor difficult to control accurately.

Jan 1, 1929

The Beginnings of Mineral Processing Research in Canada - A Short Account

Sep 13, 2010

By Jr. Koch

As a part of a larger study of the distribution of metals within ore deposits, the geometry of distribution of gold, silver, lead, copper, and zinc in five veins of the Fresnillo mine, Zacatecas, Mexico, was established. The purpose was to obtain basic data necessary for evaluation of geological theories about processes of vein formation and useful for practical mining applications in ore estimation and prediction of ore beyond present workings. The Bureau of Mines investigation comprised statistical analysis of 64,000 assay values from some 16,000 mine samples. The samples were taken at 2-meter intervals in drifts exposing the veins through a vertical range of some 750 meters. Within individual veins, the metals are distributed in dome¬like patterns with highest metal contents tending Lo occur in oreshoots at the centers of the developed parts of the veins. However, in the block of ground containing all five veins, base metals define mathematical domes with highest contents near the center; precious metals define mathematical basins or troughs with low contents near the center. The ratio of silver assay values to lead assay values corresponds to two geographically distinct types of mineralization: one in which silver is closely related to lead, and another in which silver is independent of lead. Other metal ratios also vary regularly from one place to another. The statistical methods employed in this study would be useful for other geologists or engineers who need to analyze large amounts of assay or similar numerical data.

Jan 1, 1967

By Dennis R. Dolinar

The National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory conducted a full-scale test of a composite polyurethane-aggregate seal in a hydrostatic chamber at the Lake Lynn Experimental Mine. This composite seal consisted of a polyurethane and limestone aggregate core that was formed between two concrete block walls. In the hydro-static chamber test, water is used to pressurize the seal. During the test, the maximum average water pressure the seal was able to withstand was 18.9 psi. Further, the seal began to yield at an average water pressure of only 17 psi. At the time of the test, the minimum seal design requirement was 20 psi under 30 CFR4 75.335 (2005). Therefore, based on this test, the seal did not meet the regulatory minimum design requirement. Uniaxial compressive tests conducted on samples from the polyurethane-aggregate core revealed that both the compressive strength and the elastic modulus of the material were much less than that for polyurethane only with a density of 10.0?12.0 lb/ft3. The significant reduction in the strength and stiffness of the polyurethane-aggregate mixture results from the formation of a soft polyurethane foam around each piece of aggregate. The formation of the soft foam seems to be caused by residual moisture from the aggregate. The moisture also caused the density of the polyurethane in the polyurethane-aggregate mixture to be less than the design requirements. The lower density of the polyurethane in the mixture, along with the formation of zones of pure polyurethane only, resulted in the overall seal density being less than the design requirements. During seal construction, steps were taken to control the moisture, but were not successful. An analysis of the seal failure showed that the calculated shear stresses at failure and the estimated shear strength of the polyurethane-aggregate mixture are fairly close. This suggests that the strength properties of the polyurethane-aggregate mixture along with a weak zone of poorly bonded aggregate controlled the maximum pressure the seal could withstand. At the time of the seal testing, the minimum design requirement was 20 psi, as specified at 30 CFR 75.335 (2005). New emergency temporary standards for seal designs were promulgated on May 22, 2007, with a minimum requirement of 50 psi under specified conditions. However, it will be shown that the evaluation of the polyurethane seal performance as designed to meet the older 20-psi criterion can be relevant to the design requirements under the new standards.

Jan 1, 2008

By Chas. F. Jackson

This bulletin is one of a series of Bureau of Mines reports dealing with mining methods, practices, and costs. A study of this subject was undertaken by the Bureau in cooperation with a large number of mining companies in 1928. This study continued for 5 years, during which engineers of the Mining Division of the Bureau visited most of the larger mines and many smaller ones in the United States, as well as several mines in Canada and Mexico. As a result of this study, 75 reports dealing with underground mining methods and costs at different mines were published as information circulars. Circulars also were issued on 6 open-pit mines and 2 gold-dredging operations. These circulars were written by the managers, superintendents, and engineers in charge of the operations, in some instances in collaboration with Bureau engineers. They were prepared according to a standard outline drawn up by the Bureau to obtain uniformity in textual treatment and in the arrangement and basis of setting up cost and operating data.

Jan 1, 1936

By S. H. Ash

THE MAGNITUDE of the anthracite industry's drainage problem in the Northern field of Pennsylvania is realized when it is known that, for the 8-year period 1944-51, all pumping plants in this region pumped an average volume of 112.5 billion gallons of water from the mines to the surface each year. This is over 214,000 gallons per minute pumped against an average hydrostatic head of 400 feet each year for that period (12).4 By comparison, Lake Wallenpaupack, the largest artificial body of water lying wholly in Pennsylvania, contains 71 billion gallons of water in its 24-square-mile area; the average volume of water pumped from the mines in the Northern field each year during the 8-year period was 58 percent more than the volume impounded in Lake Wallenpaupack. The natural configuration of the drainage area overlying the Northern field subdivides the total area into two major drainage areas-the Lackawanna River drainage area and the Susquehanna River drainage area overlying the Wyoming Basin. Although the 169-square-mile drainage area overlying the Wyoming Basin is slightly less than half that of the Lackawanna River drainage area (10), the total volume of water pumped to the surface from mines in the Wyoming Basin is 21 percent more than the total volume pumped to the surface from mines in the Lackawanna Basin. From this, it is apparent that the Susquehanna River and the pervious deposits in the buried valley over which it flows in its course across the coal measures of Wyoming Valley is the greatest single source of mine water affecting mines in this area. Because of its relatively flat terrain, the wide flood plain of Wyoming Valley does not facilitate rapid runoff; consequently, much of the surface water seeps directly into the buried-valley deposits and eventually into the mine workings.

Jan 1, 1953

By H. Agnerian

"A survey of 925 mineral property transactions worldwide was carried out between 1987 and 2004. These mineral properties with reported Mineral Resources include 457 gold properties, 322 base metal properties, and five platinum group element (PGE) properties. Based on constant Canadian dollars, the results of the survey indicate that:• In general, unit metal values in the ground (e.g. $/oz Au or $/lb Cu) have kept pace with the changes in the respective metal prices during the period of the survey.• A general decrease in unit gold values in the ground has occurred from about $57/oz Au in 1987 to about $11/oz Au in 2002 for Canadian mineral properties, with the exception of a peak of $58/oz Au in 1996.• A similar trend for mineral properties has occurred in the United States, but with lower unit values, in the range from $1/oz Au to $10/oz Au during the last three years of the survey. • Unit metal values in the ground for gold properties in Canada were higher than for those in the rest of the world.• Unit metal values in the ground for copper properties in Canada were in the mid-range compared with other countries in the rest of the world; the United States and Australia were higher and Latin America, Asia, Africa, and Europe were lower than in Canada.• Unit metal values in the ground for zinc properties in Canada were also in the mid-range compared with other countries in the rest of the world; Latin America and Europe were higher and the United States, Australia, and Asia were lower than in Canada.• Unit metal values for nickel properties in Canada were highest compared with other countries in the rest of the world, followed by the United States, Australia, Africa, and Asia.• Gold values in the ground in Canada have ranged from 6% to 14% (with an average of approximately 10%) of the gold price.• The unit values of base metals in the ground have been in the order of 2% of the quoted metal price, during the period of the survey."

Jan 1, 2006

By J. E. Hawley

This paper constitutes a report from the Committee on Geological Research to the Geology Division of the Institute. Two years have elapsed since a formal report was made containing several resolutions aimed at assisting geological research, a review of research equipment available, a summary of research projects suggested for consideration, and a list of research then in progress (see July, 1947, Bulletin, pp. 351-370). At this time we may note what action has been taken on the various resotions and suggestions of the Committee, indicate the more important accomplishments of independent investigators, and present a summary of the rather imposing volume and variety of research currently being carried on throughout the country. I.-Committee Resolutions and Suggestions 1.-A National Advisory Committee on Research in the Geological Sciences The original resolution adopted on the setting up of this Committee was approved with despatch by Council and was forwarded to the Minister of Mines and Resources. Due to a reorganization in the Department and possibly other reasons, no action on this important matter has yet been taken, but we are assured that some time this year such a Committee will be established by the Department of Mines and Resources. Unquestionably, it will give a fresh impetus to research in the geological sciences. When the noteworthy progress made by the research committees on Geophysics and on Soil and Snow Mechanics, established by the National Research Council, is considered, it is indeed regrettable that the Department of Mines and Resources has not acted more decisively in this matter.

Jan 1, 1949

By Paul M. Tyler

The literature on radium is already voluminous, but mcuh of it is too technical to be intelligible to the average reader, and there is no single publication that covers certain economic features of the radium industry. As a result of the renewed interest in the possibilities of domestic carnotite deposits a number of requests have been made to the Bureau of Mines for information, more particularly with reference to the business aspects of the industry. In order to meet this apparent need, the present paper has been prepared from material available in the files of the bureau. The technical data are compiled from various sources and are believed to be reasonably dependable, but the attempt has been not so much to achieve meticulous scientific accuracy as to brim; together facts of industrial significance and popular interest. GENERAL DESCRIPTION Radium is a brilliant white metal that melts sharply at about 700°C. and volatilizes appreciably at that temperature. With an estimated specific gravity of nearly 6.0, it is more than twice as heavy as aluminum and 25 per cent lighter than irons. Although it has been isolated in its metallic state, it is not used in that form, partly because it tarnishes rapidly even in dry air (forming a nitride), partly because of the greater expense of reducing it to metal, and partly because of the difficulty of dealing with such minute quantities of material. It is used always in the form of its compounds, the most important of which from the vie point of utilization are the bromide, chloride, and sulphate.

Jan 1, 1930

The contractor examined L.T. White's Patent No. 3524680 and, finding it in need of engineering refinements, proceeded with a conceptual design of a variable wall mining machine. The contractor then proceeded to assess the feasibility of the variable wall mining machine measured against the criteria specified by the U.S. Bureau of Mines. The feasibility was judged from a physical aspect, a health and safety aspect, and an economic aspect. The Variable Wall Mining Machine was judged to be feasible on all three aspects provided that certain specified practices were adopted. Description The specifications and design and performance parameters of the Variable Wall Mining System as conceptualized are summarized in Tables I and II. The system consists of a side-cutting auger operating in a string of identical 12 ft. sections, along a 500 ft. retreating longwall face. In addition to the 41 identical sections, there is a special drive and discharge section at the head gate.

Jan 1, 2012

By Bernard Lewis

This report summarizes fundamental research end technical studies conducted in the Explosives and Physical Sciences Division, Region VIII, of the Bureau of Mines in the 2 years July l, 1950, to June 30, 1952. It is the fifteenth of a series of, ordinarily, annual reports whose aim has been to provide the reader with a resume of the research results that have appeared in published form during each fiscal year under the authorship of members of the staff. These are referred to throughout the report. ACKNOWLEDGMENTS Acknowledgments art, made to the following members of the Division wider whose mediate supervision the described studies were carried out. Stuart R. Brinkley, Jr., chief, Mathematical and Theoretical Physics Section, and special assistant to the chief of the division.

Jan 1, 1953

By James D. Bamburak

Total mineral production in Manitoba has averaged C$1 billion over the past ten years. Industrial mineral production has comprised almost 10% of the total, with more than half coming from the aggregate sector. In southeastern Manitoba, tantalum, spodumene and amblygonite concentrates, cesium and rubidium ores, cesium formate, dimension stone and sphagnum peat moss are produced. Gypsum, high-calcium limestone and lime are produced in the Interlake area. Early industrial mineral production consisted of tools and implements, salt and pottery. Historical production has included: salt, building stone, aggregate, lime and dolime, lignite coal, gypsum, natural and Portland cement, calcium bentonite, brick, light-weight aggregate, caustic soda and soda ash, and silica sand. Future industrial mineral production may come from reactivated quarries, pits and wells or from new producers of current commodities. Newproducts may include: stainless steel master alloy, silicon metal, titanium and magnetite, lithium carbonate, float-plate glass and ferrosilicon, "marble" dimension stone, magnesium metal, potash and kaolin.

Jan 1, 2001

The inherently explosion-proof mine (EPM) concept is based upon the non-flammability of certain combustible-oxidant-inert gas mixtures, and the effect of partial pressure of gases on physiological reactions. In a properly controlled underground environment, gas explosions are impossible, men can do work, and relatively high concentrations of methane would be permitted. A systems analysis has been performed to examine the physiological, engineering, and economic feasibility of such a concept, and methods and equipment are recommended for maintaining an EPM atmosphere in a bituminous coal mine producing a nominal two million tons of clean coal per year. It is concluded that: engineering feasibility can be demonstrated using subsystems and components that can be designed and built within the present state-of-the-art, that economic feasibility is possible within approximately five years, and that physiological feasibility is sufficiently promising to warrant continued investigation.

Jan 1, 2012

By J. C. Boswell, J. D. Crawford

IN addition to its base-metal and coal mining operations, the United States Smelting Refining and Mining Company has, for the past quarter century, been one of the few large American mining companies interested in dredging. Its activities in this field are confined to gold, and to Alaska, but it is the largest operator in that territory, with twelve huge dredges available to work during the summer on the frozen ancient beach sands at Nome and the gravels of Fairbanks. These operations will be described separately.

Jan 1, 1948

By S Bourke, R Stone, B Hill

Since Jameson Cell flotation technology was first installed in a coal flotation application in 1988/89 at Newlands Coal Handling and Preparation Plant (CHPP) there have been fundamental improvements to its design which has led to its current status as the leading technology in Australia for fine coal flotation. These improvements, which include key hardware modifications, consist of the re-development of the orifice plate to produce considerable increase in wear life and reduction in power consumption for a given air entrainment and a significant increase in the amount of air that is entrained. Modifications to the downcomer allow maximisation of residence time and air entrainment while changes to the feed and air distribution system allows a reduction in installation cost and a reduction of solids ingress into the air line. Additionally, operational improvements such as the use of recycle to maintain constant flow to the cell feed are discussed. The recent installation at Hail Creek in the Bowen Basin, which consists of three B6000/20 Jameson Cells (6 m diameter bottom-fed distributor with 20 downcomers) will be reviewed as a case study. The latest design and operability of the cells are summarised and compared against one of the original designs at Riverside CHPP also in the Bowen Basin.

Jan 1, 2005