Search Documents

By Iwasaki I.

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates, and the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when anionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were most strongly affected by the level of starch, to a lesser degree by the pH, and were virtually independent of the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semi-taconite could be readily attained with starch and calcium chloride.

Jan 1, 1968

IT is intended in this paper to present in broad outline to the members of the Institute a short account of the conditions and operations that constitute what is, variously known as Subterranean Warfare, Military Mining, or Tunnelling. Realizing ,the magnitude of the operations, and the varied and minute details met with in them on,the Western Front, it is the writer's intention to confine these notes to operations carried out by the First Australian Tunnelling Company. In so doing there is no wish to detract from the very fine records of the Second and Third companies it is to be hoped that members of the Institute (or others) who were with these companies will write accounts of their doings-the former in the water-logged areas to the south of Armentieres, and later in the sand-dunes at Lombardzee, and the latter in the chalk area of the Lens coal...

Jan 1, 1920

By L. A. Morley

This report summarizes the work performed on Bureau of Mines Contract J0199106, "Portable Trailing Cables, Splices, and Couplers - Design and Installation Considerations," from May 1, 1979 until December 31, 1981. Splice installations and considerations for the possible use of conductive-rubber shielding in low-voltage trailing cables as well as coupler installations in high-voltage cables were the principal tasks. Flammability measurements on cable components and general testing facilities for mine electrical equipment were secondary tasks. Theoretical and empirical data indicate that conductive rubber with high resistivity values is an unsatisfactory shield design for current-sensing fault detection. Elimination of partial discharge in coupler installations requires meticulous care.

Jan 1, 1982

By Henry H. Ginsberg

The Federal Bureau of Mines made pilot plant investigations of the process requirements necessary to produce heavy fuel oil by the liquid-phase hydrogenation of bituminous coal. The investigation was carried out in three separate series of experiments. The first series studied the effect of temperature and contact time on product distribution at 3,500 p.s.i.g. and 420° to 480° C. in the presence of 0.1 wt.-pct../ stannous sulfide plus 0.05 wt.-pct. iodoform based on gross coal. As a result of increased contact times and temperatures, the conversion-6/ and yield of hydrocarbon gas increased, the viscosity of product oil decreased, and elimination of oxygen, nitrogen, and sulfur from coal increased. The yield of oil did not indicate any definite trend with changes in temperature and contact time. The yield of oil ranged from 76 to 85 pct. for Pittsburgh coal and from 60 to 85 pct. for Rock Springs coal. Asphaltenes in the product oil ranged from 17 to 38 pct. of the total oil for Pittsburgh coal and from 12 to 22 pct. for Rock Springs coal. Fuel oils meeting Bunker C or American Society for Testing Materials (ASTM) Grade 6 specifications were produced with Rock Springs coal at 0.2- to 1.0-hr. contact time and 440° to 480° C. and with Pittsburgh coal at 0.3- to 1.0-hr. contact time and 420° to 460° C. In the second series of experiments tin, nickel, iron, and zinc were evaluated as catalysts for the hydrogenation of Rock Springs coal to heavy fuel oil at 3,500 p.s.i.g. and 460° C. Using the apparent conversion of coal as criterion of catalyst activity, at a contact time of 0.45 hr. tin was the most effective catalyst; nickel and iron were nearly as effective, but the use of zinc resulted in much lower conversion. When the contact time was increased to 0.80 hr., the apparent conversion of coal was essentially the same for each of the catalysts. When the yield of oil boiling below 3550 C. was used as criterion of catalyst activity, at 0.45 hr. the order of activity was tin, iron, nickel, and zinc; at 0.80 hr. tin was far superior and the others were essentially equal. The product oils contained from 8 to 20 pct. asphaltenes.

Jan 1, 1960

Martin Marietta Aluminum, Inc. followed Howmet Aluminum Corp., Revere Copper and Brass, Inc. and Anaconda Co. in lifting August prices of 99.5 percent unalloyed aluminum ingot by 3 cents to 56 cents per pound. Prior to these moves, Kaiser Aluminum and Chemical Corp. raised its June ingot listings by 4 cents to 57 cents and Consolidated Aluminum Corp., 4.5 cents to 57.5 cents. Domestic merchants increased July quotes by slightly more than 1 cent to 51.3-51.8 cents per pound. ARSENIC The Occupational Safety and Health Administration (OSHA) issued new standards, effective August 1, for worker exposure to inorganic arsenic, a toxic substance linked by OSHA to lung and lymphatic cancer. The new standard will limit worker exposure to 10 micrograms per cubic meter of air over an 8-hour period, a drastic reduction from the previous standard of 500 micrograms for a like period. Implementation of the new standards may be the most difficult and costly for copper smelters where arsenic is associated with the copper feed material but problems will also be encountered by producers of arsenic containing products such as for pesticides and herbicides. The new standards allow use of personal protective gear for workers as an interim measure until plant engineering controls can be put into effect.

Jan 1, 1978

This volume constitutes the final report for the Rescue Subsystem portion of the Coal Mine Rescue and Survival System program conducted by the Westinghouse Electric Corporation under contract to the United States Bureau of Mines (Contract Number H0101262 dated Jung 17, 1970). The program was directed by the Special Systems Department of the Westinghouse, Baltimore, Maryland facility. The basic objectives of the CMRSS program were to develop and test hardware to determine the efficacy of a variety of coal mine rescue and survival concepts and techniques. These concepts were drawn from two major- sources: the Request for Proposal from the Bureau of Mines and the final report on the Mine Rescue and Survival Study conducted by the National Academy of Engineering (NAE).

Jan 1, 1971

By S. V. Krishnan

Stability of fine quartz suspensions in process water is of concern in several mineral processing applications. In alkaline solutions, the presence of magnesium ions, arising from such sources as water hardness and magnesium-bearing minerals, leads to the precipitation of Mg(OH)2 which coats the surfaces of quartz. The conditions under which heterocoagulation or surface precipitation of Mg(OH)2 on quartz occur and the manner in which they influence the settling behavior of ground quartz was studied by means of settling tests, coating density determinations, zeta potential measurements and electron microscope observations. Coating density was greater when Mg(OH)2 nucleated on the surface of quartz than when the precipitates heterocoagulated on the quartz surface. The settling curves of quartz suspensions in the presence of different concentrations of MgCl2 exhibited a maximum of maxima which occurred at 10-3M MgC12 and pH 11. Interactions between quartz and Mg(OH)2, and flocculation-dispersion characteristics of quartz suspensions in this system are discussed.

Jan 1, 1983

By Armstrong A

Queensland is Australia's second largest mining state with world-class deposits of coal, base metals, bauxite and magnesite. The total value of Queensland's mining production is about $5 billion per annum, and coal accounts for around 55 per cent of that total. The environmental issues which arise as part of management and regulation of the industry are resolved within the EMOS process. The Environmental Management Overview Strategy is the cornerstone of the policy 'Environmental Management for Mining in Queensland' developed jointly by the Queensland Department of Minerals and Energy and the mining industry. The Gordonstone Coal Mine is the largest underground mine to gain approval under the new policy. Accordingly, Gordonstone has a well planned environmental management program which takes into account site-specific factors and provides for continuous compliance with the provisions of the Mineral Resources Act in a self-regulatory context.

Jan 1, 1994

By William R. Jones, Robert M. Hernon

This report on the Central mining district of New Mexico is the partial culmination of an intensive U.S. Geological Survey effort dating back some 30 years. Robert M. Hernon went to Silver City in 1948 to finish a detailed restudy of the district that had been started in the thirties by Samuel G. Lasky. He was joined by William R. Jones in 1951, and Jones took over as project chief when Hernon resigned to do consulting work in 1953; it was under Jones' guidance that most of the work was brought to completion or nearly so ( 17, 22-24, 26-30). Hernon returned to the Survey in 1958 to work in .the southern Appalachians. Early in 1965 Jones urged that Hernon be reassigned to the Silver City project to help complete the Professional Paper report on the ore deposits of the Santa Rita quadrangle as well as to take over preparation of the report on the Central district for the Graton-Sales volume. This reassignment was approved, and Hernon began work on the present report. By late June he had completed most of it in draft form, and on June 28 Jones and Hernon left Denver for a short trip to Silver City to fill in a few gaps and to reacquaint Hernon with activities in the district, which he had not visited for 12 years. Late in the afternoon of June 29, 1965, as Bob and Bill were 85 miles short of their destination, their jeep collided head-on with a truck that was attempting to pass another vehicle in a cloud of dust. They both died instantly. As the most recent surviving member of the Silver City project (1958-1962), I was given the honorable though rather sorrowful task of putting the Hernon-Jones report "in shape" for publication. Fortunately the manuscript was already in good shape, so that the task has consisted of little more than minor reorganization and editing, and of preparation of the illustrations, abstract, and bibliography. The sections on wall-rock alteration had been left for Jones to complete in the light of his recently intensified interest in alteration geochemistry (25), and it is in these sections only that. the report may fall short, for they have been filled in from a 1958 manuscript by Jones on the ore deposits of the Santa Rita quadrangle that he intended to revise considerably. The shortcomings, however, are largely in the interpretation, not in the field data. As a brief but accurate summary of what was known about the geology of the Central mining district in 1965, this report stands as a fitting testimonial to the scientific dedication of two exceptional men.

Jan 1, 1968

By R. C. Buehl

A pyrometallurgical process for recovering manganese from open-hearth furnace slags or low-grade manganiferous iron ores is described. The slag or ore is smelted in a blast furnace to produce spiegeleisen; the speigeleisen is then blown with air in a basic converter to give an oxide slag. This slag product contains 60 to 75 percent manganous oxide and may be considered a synthetic manganese ore. In the smelting operations coke rates for five test periods ranged from 3,255 to 4,130 lb per ton of spiegeleisen. The recovery of manganese in the spiegeleisen varied from 60 to 76 percent. Recovery increased to 83 percent when the open-hearth slag feed to the blast furnace was diluted with a high-? grade iron ore sinter to facilitate smelting. In blowing the spiegeleisen a cyclic procedure was developed that gave nearly 90 percent recovery of manganese in the slag product (synthetic ore) yet prevented excessive contamination of the slag by phosphorus and iron. The overall recovery of manganese was about 75 percent when iron ore sinter was used with the open-hearth slag in the smelting step. The metal remaining after oxidizing the manganese from the spiegeleisen contained approximately 3.5 percent phosphorus. It was refined in a basic converter by blowing with air in the presence of lime" A high--grade iron and a basic phosphate slag were produced.

Jan 1, 1965

By J. B. Clemmer

Fluorspar is one of the most important nonmetallic minerals and is used extensively in the metallurgical, ceramic, cement, and chemical industries. The steel industry consumes most of it, but as the Mineral is the chief source of fluorine, it is becoming increasingly valuable to the chemical industry in the production of fluorine compounds The development of nontoxic organic fluorides for use as refrigerants in mechanical refrigeration and air-conditioning units illustrates the increasing use of fluorspar in the chemical industry. Most domestic flurospar comes from deposits in the Illinois-Kentucky district, which centers around Rosiclare, Ill. About a dozen companies operate in the district, which comprises parts of Pope and Hardin Counties in southern Illinois and Crittenden, Livingston, and Caldwell Counties in western Kentucky. According to the latest available statistics, this district supplied 1/5,960 short tons of fluorspar in 1937, compared with the total domestic production of 181,230 tons. Imports totaled 37,063 tons.

Jan 1, 1939

By J. B. Clemmer

Fluorspar is one of the most important nonmetallic minerals and is used extensively in the metallurgical, ceramic, cement, and chemical industries. The steel industry consumes most of it, but as the Mineral is the chief source of fluorine, it is becoming increasingly valuable to the chemical industry in the production of fluorine compounds. The development of nontoxic organic fluorides for use as refrigerants in mechanical refrigeration and air-conditioning units illustrates the increasing use of fluorspar in the chemical industry. Most domestic flurospar comes from deposits in the Illinois-Kentucky district, which centers around Rosiclare, Ill. About a dozen companies operate in the district, which comprises parts of Pope and Hardin Counties in southern Illinois and Crittenden, Livingston, and Caldrell Counties in western Kentucky. According to the latest available statistics, this district supplied 165,960 short tons of fluorspar in 1937, compared with the total domestic production of 151,230 tons. Imports totaled 37,063 tons.

Jan 1, 1939

By Sara J. Davenport

With the increased demand for mercury incident to preparations for national defense and the reduction in imports from some of the usual sources owing to war conditions, many small mines in the United States Pure now being worked that ordinarily would be unprofitable. This is indicated by the following table on mercury produced in the Unite States in 1939-40 (1)4/

Jan 1, 1941

By H. C. Fuller

This paper discusses 105 production runs at Boulder City, Nev., in which titanium metal was made in 200-pound batches. It describes the equipment and techniques used in preparing raw material, the reduction process, and the removal of the reaction mass from the reaction vessel. Also, some data on man-hour requirements are presented. The main emphasis was on producing ductile-grade titanium and developing a standard procedure for obtaining a consistently pure product. Some departures from techniques used before were found to be desirable. The most important of these was the use of a sealed room with a controlled dry atmosphere in which the reaction vessel was opened and the reaction mass removed. This minimized the moisture taken up by the magnesium chloride in the reaction mass, and it could be purified successfully by vacuum distillation. Using the dry room also made it possible to leave al-inch shell of the reaction material on the walls of the vessel, which lowered the iron contamination and eliminated the labor and time-consuming job of cleaning the vessel after each reduction. Another change was lowering of the temperature during reduction to 750° C. instead of 850° C. This was found to give good results more consistently. The first poke to break the crust during reduction was eliminated, as it was found to be unnecessary and only added more work and was another possible way of introducing air. A rotating feed arm was installed in the reaction vessel to distribute the titanium tetrachloride over a larger area and, thus, prevent local overheating. The process, conducted in a batchwise manner as described and followed by good purification and fusion, produces a metal adequate in quality for nearly all purposes.

Jan 1, 1952

By CIMVAL

This Code for the Valuation of Mineral Properties (the “CIMVAL Code”) is the result of a review more than a decade after the release in 2003 of the “Standards and Guidelines for Valuation of Mineral Properties” (the "2003 Standards"). The purpose of the review is to update the 2003 Standards to reflect domestic valuation, international valuation, and regulatory developments. The CIMVAL Code was adopted by the Canadian Institute of Mining, Metallurgy & Petroleum (the "CIM") Council on November 29, 2019. The CIMVAL Code supersedes the 2003 Standards. The 2003 Standards were dated February 2003 and were adopted by the CIM Council on March 9, 2003 as the first comprehensive set of standards for Valuation of Mineral Properties in the Canadian mining industry. The 2003 Standards followed recommendations of the Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission, where in its Final Report (January 1999), the CIM was specifically asked to form a committee of valuation practitioners to review and advise on standards for the Valuation of Mineral Properties. The Special Committee on Valuation of Mineral Properties ("CIMVAL") was created on May 5, 1999 with the mandate to recommend standards and guidelines for Valuation of Mineral Properties to be used by the mining industry in general. The CIMVAL Code is limited to the Valuation of Mineral Properties (including any interests therein) and does not cover valuation of corporations or other entities that hold Mineral Properties as assets. The CIMVAL Code does not cover petroleum and related assets. CIMVAL recommends that the CIMVAL Code be followed for all Valuations of Mineral Properties, including those required by securities administrators and stock exchanges. However, when a Valuation is required under the applicable rules of securities administrators or stock exchanges, such rules prevail to the extent of any inconsistency.

Nov 29, 2019

By H. P. Hamlin, W. A. Grosh

Samples of clays , shales , and argillites from 21 locations were subjected to preliminary bench- scale tests for bloating properties , and several samples were tested for ceramic properties . Samples showing favorable bloating properties were further tested in a pilot - plant - scale rotary kiln . Physical characteristics and concrete -making properties of the bloated products were determined . The Decorah shale from one area made a suitable material for a lightweight aggregate ; however , the limestone layers in the formation must be eliminated or the resulting activated lime must be controlled by quenching .

Jan 1, 1963

By Mukund O. Gangal

A deep cutting continuous miner, HH456, was tested under production-mining conditions at the Joanne Mine, Rachel W. Va., for about 1 ½ years (226 production days). The miner was run in two modes: a low head-rpm, deep cutting and high rpm, shallow-cutting mode. These tests confirmed that deep cutting and slow cutter speed reduce respirable dust significantly under production mining conditions. Quantitative reductions in dust, in deep vs shallow cutting, were 73°; in return air and 63% at the operator's location. Production rate, (tons/shift), and bit consumption rate did not show any relationship to deep or shallow cutting. Reliability and maintainability of the miner were worse in deep cutting mode due to cutter drive shaft failures; the cutter shaft problem was solved through improved material and design. Excluding the cutter shaft repairs. maintainability war similar for deep and shallow cutting,

Jan 1, 1979

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

A new series of reports called ?Mineral Perspectives" (MP's) has been initiated by the Bureau of Mines with the publication of MP-1 titled, "Far East and South Asia" by K.P. Wang and the staff of the Bureau of Mines. This new series parallels the creation of the recently announced "Minerals Commodity Profiles" (MCP?s). Both series are designed to provide current information on important sectors of the mineral economy to assist professionals in government, industry, and education in monitoring supply-demand relationships that have significant impact on our domestic economy as well as on the international scene. The orientation of the "Mineral Perspective" series is a geographic one which examines the mineral situation of a region or a country. The "Mineral Commodity Profile? series examines individual mineral commodities. They are in this sense complementary.

Jan 1, 1977

By Edwin B. Wilson, Charles F. Cockrell

The application of evolutionary operation is proposed for the cleaning of coal by the heavy media process. Analysis of the data given suggests some benefits that may not be immediately appreciated unless evolutionary operation is applied. For example, while it may seem obvious to increase specific gravity when the ash and sulfur content of the clean coal is lower than that allowed, evolutionary operation may show that an increase in feed rate or an increase in both feed rate and specific gravity would be a more profitable alternative. In addition, by using evolutionary operation, up-to-date knowledge of the effect of change of feed rate or specific gravity on yield and product quality is available. This information facilitates confidence about decisions made in regard to the day-to-day operation of these units. A number of other applications in the minerals industry are proposed. An application of evolutionary operation in a related field is also given where a large number of variables were required to be optimized.

Jan 1, 1969