Search Documents

By Yves Breau, François Robichaud, Jacques McMullen, Pierre Pelletie

"The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.INTRODUCTIONThe East-Malartic mill is located close to the town of Malartic in North Western Quebec, Canada. The mill was first commissioned in 1938. The flowsheet at that time was a straight cyanidation circuit. The original mill operated in that mode up to the discovery of the Bousquet 2 orebody in 1989 which consisted of a massive copper sulphide ore averaging 0.7% copper and 7 g/mt of gold. Bousquet 2 ore processing required a mill retrofit. Grinding capacity, gravity and copper flotation circuits were inserted prior to the cyanidation circuit in order to achieve 3,200 mtpd capacity at expected recoveries.In 1993, control of the flotation circuit was deemed critical in order to maintain the flotation performance and to reduce cyanide consumption since the copper sulphide contained in the Bousquet 2 ore is a high cyanide consumer (50% bornite). (McMullen, 1999) As a result, the implementation of advanced control strategies in order to increase the metallurgical profitability of the plant and to reduce the operating variability between operators was the most rational alternative. In 1994, Corem was chosen to perform the plant audit and to write the first set of rules. The on-line control strategy was started up in 1995. In 1996 and 1997 the Expert System was shutdown because of an extreme change in the ore coming from the milling of Bousquet #1 ore and the departure of the projects engineer. In 1998, the system was restarted and the results were impressive. Furthermore in May of 2001 a patent was issued for the control strategy. (Breau, 2001)"

Jan 1, 2002

By M. Botz

For leach solutions containing primarily free cyanide, the silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method significantly over-estimates the concentration of free cyanide and under-estimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric titration method for determining WAD cyanide that overcomes issues with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to fully release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, accurate WAD cyanide measurements were achieved using the MP-WAD method. Analyses obtained with the new method were found to be within about ±10% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.

Feb 27, 2013

By R Bartlett

Process engineering-science originally developed for percolation leaching of ore in heaps is extended to the decontamination of unsaturated soil, either in situ or after excavation and emplacement as a soil heap on an impervious pad. Phenomena considered include: soil matrix porosity and permeability; percolating solution retention, capillarity and flow; washing sweep efficiency; optimum solution application rates during leaching; soil agglomeration to improve soil permeability and soluble contaminant transport by diffusion in soil agglomerates. Practical aspects briefly discussed include leach pad construction, solution distribution and recovery from the soil, and solution containment.

Jan 1, 1994

By M A. Faizulin, N G. Stukalova

The present till now practice of averaging of ore by metal content at mining-dressing enterprises does not allow evaluating objectively really existing regularities of dressing process. The processing of large statistical data by specially designed methods has revealed the relationships of extracted mass of metals into concentrates when processing of ore at preparation plants. The analysis of the obtained relationships points to necessity of timely control by flows of ore with due account of different sorts of metal. For this problem solving it is offered to use specially designed methods on carrying out of calendar planning of a mining and shipment of ore at open casts, based on ranked arriving of flows of different sorts ores to preparation plant. The given methods includes economic-mathematical model forming and its implementing by worked out method. The formed model allows taking into account different technological and organisation limits, typical operation conditions of open cast and preparation plants. Using this methods of control of mining operations and designed on its basis the complex of software allows increasing volume of metals, extracting into concentrate, up to two per cent without any additional costs and saving of the existing technological schemes at preparation plant.

Jan 1, 2003

By Kenneth N. Han, Peter Mam-soo Kim

The extraction behavior of gold in ammoniacal solutions in the presence of bromine as an oxidant has been studied. The effect of concentration of ammonia, bromine, and pH of the solution on the rate of dissolution of gold was investigated. The dissolution behavior has been analyzed using electrochemical method, and its results were compared with direct leaching tests using gold powder. The overall dissolution of gold in ammoniacal solution containing bromine was found be affected significantly by pH of the solution and the concentration of bromine. The rate expression found in this study has the following form.

Jan 1, 2005

By J. F. Butler

The degree and type of carbide dispersion resulting from changes in the cooling rate from austenite determine the amount of carbon remaining in solution after slow cooling- from a subsequent subcritical annealing treatment. A difjusion model has been proposecl to explain the effect of carbide dispersion on the amount of carbon retained in solution and the amount of carbon in solution has been related to the degree of carbon strain aging. COTTRELL and Leak' have shown that the rate of strain aging in low-carbon steels is dependent upon the amount of carbon and nitrogen in solution. Carbon can be effectively removed from solution as Fe , C by quench aging at temperatures of 200" C or lower; however, the relatively higher solubility of nitrogen at these temperatures prevents sufficient removal of nitrogen as iron nitrides. For this reason, nitrogen in solution has been considered the major cause of strain aging in rimming grades of commercial low-carbon steels. Nitrogen can be effectively removed from solution and nonaging steel produced through the addition of aluminum to form the stable nitride, AlN; however, the aluminum also causes deoxidation resulting in a killed steel. III an attempt to produce a rimmed steel which was also nonaging, Morgan and Shyne 2 investigated tile strain-aging properties of low-carban steels containing boron and found that strain aging was suplx-essed in steels containing as little as 0.007 pet B. The original purpose of this investigation was to determine the mechanism of strain-aging suppression by boron. Early in the study, the function of boron was discovered to be much like that of aluminum in that the formation of a nitride, BN, removed the nitrogen from solution.' However, during the course of the investigation, an effect of heat treatment upon the strain-aging properties and the amount of carbon in solution was found which could be related to the microstructure of the steel. The purpose of this paper is to examine these relationships among heat treatment, microstructure, carbon in solution, and strain aging in steels where nondetectable amounts of nitrogen are present in solution. EXPERIMENTAL PROCEDURE The investigation was carried out using 0.030 in. by 12. in wire specimens which had been cold swaged and drawn to the final diameter. Table I lists the compositions of the low-carbon steels used. Those with 'V' designations were vacuum melted and cast; the alloys designated 'AISI' were prepared from high-purity iron obtained from the American

Jan 1, 1962

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

By D. Muraoka

Introduction Soda ash, anhydrous sodium carbonate, is produced from underground trona deposits occurring in the Green River Basin of southwestern Wyoming. Stauffer Chemical Co. of Wyoming, a jointly owned subsidiary of Stauffer Chemical Co. and Rocky Mountain Energy Co., mines the trona and processes it into high-purity soda ash. Stauffer Wyoming has been in operation since 1962 with a current production capacity of about 1.8 Mt (2 million st) per year of soda ash. The refinery has five parallel operating trains using the monohydrate process which is a series of chemical processing unit operations described below. Screening and Crushing The mined trona is brought to the surface in two counterbalancing ore skips. The ore is initially screened with refinery feed (less than peagravel size material) entering the process. Oversize is conveyed to an outdoor stockpile. Ore is recycled from under the stockpile via cone feeders as the refinery needs require. The ore is conveyed to hammer type crushers and screened. The refinery feed enters the process and the oversize is recycled to the crushers. Calcining The first step in refining trona to soda ash is calcining the trona ore. This is accomplished in concurrent flow, rotary kilns that are direct fired with natural gas. [2 (Na CO NaHCO 2H O) Heat 3Na CO + 5H20 + CO 2 3~3~ 2 ~~2 32] The trona ore is fed to the kiln at the burner end and is intimately mixed with the hot exhaust gases from the burner. Direct contact with the flame is avoided. The ore moves down the kiln by gravity and rotation aided by the kiln's internal lifters. The exhaust gases are cleaned to 99 + % particulate removal and discharged to the atmosphere. Dissolving the Calcined Trona The calcined trona is conveyed from the kiln discharge to a rotary drum dissolver where it is mixed with water and weak solution (unsaturated solution of calcined trona in water). The calcined trona is soluble whereas the impurities, primarily shale, are insoluble. The discharge from the dissolver is a slurry containing saturated solution (about 30% dissolved calcined trona in water), some undissolved calcined trona, insoluble impurities, and organic impurities. The dissolver discharge enters a rake classifier that makes the first solid/liquid separation in the process by removing the heavy undissolved material from the saturated solution. This undissolved material is conveyed to a second rotary drum dissolver and mixed with water to dissolve any remaining calcined trona. The secondary dissolver discharges to a second rake classifier that separates the solids from the liquid. The solids are now primarily insoluble impurities with very little unrecovered calcined trona. These wastes are conveyed to evaporation ponds for disposal. The liquid from the secondary rake is recycled to the primary dissolvers' weak solution system. Returning to the primary rake classifier, the saturated solution which contains suspended insoluble muds is pumped to a thickener. Flocculant is added to aid settling of the suspended muds. The flocculated muds are collected at the bottom of the thickener and pumped to vacuum cloth filters. The adhering saturated solution is separated from the muds that remain on the filter cloth. The recovered solution is returned to the dissolvers' weak solution system. The muds are reslurried and pumped to the evaporation ponds for disposal. Saturated solution, containing some suspended insoluble muds along with the organic impurities, overflows the thickener. Filtering the Saturated Solution The saturated solution overflowing the thickener enters a holding tank where it is pumped to a bank of pressure leaf filters. The suspended muds are captured on the filter leaves while the cleaned saturated solution is pumped to polishing filters. The polishing filters are also leaf pressure type, intended to remove any suspended solids that may pass the primary filters. Organic impurities are removed with activated carbon. The purified solution is now free of insoluble muds and has most of the organic impurities removed. Crystallizing and Drying the Monohydrate The purified saturated solution is pumped to evaporative crystallizers. The solution is circulated from the crystallizer vessel through a heat exchanger. Indirect contact with steam in the heat exchanger causes the saturated solution to boil, thus crystallizing the soda ash in its monohydrate form. Slurry crystal density is maintained in the crystallizer by simulta¬neous feed of fresh saturated solution and drawoff of the slurry.

Jan 1, 1986

The dissolution kinetics of cobalt in iodine/iodide solutions was investigated using a rotating disc technique. Variables studied here included temperature, rotating speed, concentration of lixiviants, and pH of the solution. The overall dissolution reaction was found to be limited by mass transfer of tri-iodide through the diffusion boundary layer with Arrhenius activation energy of less than 16.2 kJ/mol (4 kcal/mol) over the temperature range, 2-42°C. The pH of the solution had little effect as long as the pH of the solution was less than 8. However, when the pH of the solution became greater than 8, the dissolution rate decreased dramatically due to passivation. The rate of dissolution was in good agreement with the dissolution model developed by the authors earlier.

Jan 1, 1994

By K. N. Han

The dissolution kinetics of cobalt in iodine/ iodide solutions were investigated using a rotating-disc technique. Variables studied included temperature, rotating speed, concentration of lixiviants and the pH of the solution. The overall dissolution reaction appeared to be limited by the mass transfer of tri-iodide through the diffusion boundary layer with an Arrhenius activation energy of <16.2 kJ/mol (4 kcal/mol) over the temperature range of 2 to 42ºC. The pH of the solution had little effect, as long as the pH of the solution was <8. However, when the pH of the solution became >8, the dissolution rate decreased dramatically, due to passivation. The rate of dissolution was in good agreement with the dissolution model developed by the authors earlier.

Jan 1, 1995

By Karel Van Acker

The automotive is a sector where energy consumption during the use phase prevails over the production and the end-of-life phase. Therefore, a lot of research and innovations at replacing classical steel parts by lighter materials like light metals and polymer composites. While composites are very attractive for the use phase of cars, their introduction suffers from the limited end-of-life options for composite structures. An extensive life cycle analysis for a reference car design has been conducted to study the effects of replacement of conventional steel structures by lightweight carbon fibre composite alternatives. The study also takes second order effects in the design of the car into account. The opportunities and treats of the trend towards more intensive use of carbon-fibre composites in car design are identified. A discussion on the potential of other types of composites for the automotive in terms of sustainability considerations is added.

Jan 1, 2010

By J. M. Smith

This resume provides an account of the work of the Bureau and it's establishment by an Act of Parliament in August 1916. The Medical Bureau is concerned solely with the administration of the medical provisions of the Act. Its main functions are to conduct and to direct or control the medical examinations provided for in the Act. The paper covers the changes in type of silicosis, classification into the three legal stages of silicosis, cancer of the lung and tuberculosis.

Jan 1, 1947

By D O. Hayba

Metal-rich slurries discharged from excess-enthalpy geothermal wells at Kawerau (NZ) indicate that an efficient ore precipitation mechanism operates in some feedzones. In our conceptual model, which takes into account the relative permeabilities of liquid and gas phases in boiling fluids, a metal-precipitating liquid phase is effectively immobilised along boiling fronts, leading to the formation of highly concentrated ore. Chemical equilibrium and heat/mass transport modelling demonstrate the general applicability of this conceptual model to hydrothermal eruption environments.

Jan 1, 1995

By Lloyd A. Morley

This Bureau of Mines publication presents a comprehensive review of mine electrical power-system theory and practice. It discusses fundamental theory and the vital aspects to be considered in planning and designing mine electrical power systems. The report is divided into three major sections. The first presents the history of electricity in mining and the fundamentals of electrical phenomena and components. The second focuses on power-system components: motors, grounding systems, cables, and protective equipment and devices. The final section includes mine power-center equipment, switchhouses and substations, batteries, and mine maintenance.

Jan 1, 2003

By Charles H. White

METHODS in colorimetry are based on the assumption that the intensity of the color of a definite volume of solution is directly proportional to the quantity of the color-producing substance&apos; present. In the preparation and examination of colored solutions there are three ways in which the depth of color may be varied. These variables are; (1) the quantity of the coloring matter, (2) the quantity of the solvent, or the dilution, and (3) the thickness or depth of that portion of the solution examined. With these three variables as a basis, three general methods in colorimetry have been devised, all of which have been used in the determination of carbon in steel. In the first method, the quantity of the solution is kept the same for both the unknown steel and the standard, and the sections compared are of equal thickness, while the quantity of the standard is varied until the color obtained is of the same intensity as that produced by a definite quantity of the unknown steel. In laboratories where this method is used there is pre¬pared and kept for permanent use a series of solutions with varying amounts of the standard, representing the percentages of carbon from the lowest to the highest demanded in that laboratory. These standard solutions are kept in bottles, or test-tubes of equal diameter, and are arranged in series from the faintest to the most intense color, so that it is a simple matter to find the place of the unknown steel in the series, when the solution is of a definite volume and is contained in a tube of the same diameter as the standard tubes. In the second method, equal quantities of the standard and of the unknown steel are dissolved, the standard is diluted to a definite volume, and the solution of the unknown steel is di-

Sep 1, 1906

By T Graham

The invention of the traditional belt and idler conveyor system is attributed to Thomas Robins in 1892. This basic concept, ubiquitous in most mining operations, has not changed markedly in 125 years and still suffers from five forms of energy losses. Firstly, Wheeler, Roberts and Jones (2004) showed that indentation rolling losses, a consequence of the indentation a roller inflicts on the belt, consume 60 per cent of all energy. Secondly, Wheeler (2006) explained that bulk solid flexure resistance resulting from material interaction and movement absorbs 20 per cent. The remaining energy is lost by idler rotating resistance (5 per cent), belt flexure resistance (5 per cent) and secondary resistances (10 per cent).Traditional conveyor systems are continuous as opposed to batch systems, implying both positive and negative features. On one hand, continuous systems have high availability (available infers ‘ready to run’), but, on the other, utilisation of availability is often low; for example, when a conveyor is running empty or below capacity. This converts into reduced system OEE (overall effective efficiency). Many attempts have been made to mitigate energy losses and low OEE issues, including development of rail-based systems. The key drawbacks have been higher capital cost, low flexibility, poor availability and lack of market acceptance.A recent conceptual development known as the ‘autonomous rail conveyor’ (ARC) promises to address issues of energy loss and poor availability and provide increased flexibility by offering solutions for difficult applications. The ARC uses a series of interconnected skeletal bogies covered with a conventional conveyor belt as a load bed running on relocatable light rail. The bogeys have two axles, each driven by integrated variable speed-geared motor and brake systems, and are connected to previous/next bogeys by specialised couplers. Power is provided by a generator (located in a dedicated bogey) and ‘daisy chain’ plug in cables. Centralised redundant control is provided at a preferred point. Although the system is batch in nature, the number of carriages and trains is flexible, meaning that the system is effectively continuous. Loading is achieved by feeding the ARC from a perpendicularly oriented apron feeder, while material off-loading is accomplished by a twist-dump operation in which the belt is twisted through an angle of 50&#176; below the horizontal, causing material to flow from the belt into a receiving conveyor.The ARC system can run multiple trains over any distance, although benefits are more significant in distances of over two kilometres. Capital and operating costs are predicted to be lower than competitive products, with planned maintenance being simple to perform.CITATION:Graham, T, 2017. The autonomous rail conveyor significantly reduces ore haulage costs, in Proceedings Iron Ore 2017, pp 467–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By C. W. Won

a-etchant solution is the waste material obtained during the etching by ammoniacal solution of printed circuits for PCs. This material contains a substantial amount of copper (13-14%) but is usually discarded after neutralization. In this work, copper recovery from such solutions by electrowinning or cementation using iron scrap was tested. For each method, the effects of temperature, solution pH, initial copper-ion concentration, and reaction time were investigated to obtain optimal conditions for copper recovery.

Jan 1, 1993

By Wenbo Lu

A combined method is present in this paper in analysis the dynamic stability of rock slope under the loading of blast induced seismic, in which, by combining the dynamic load calculating method of quasi-static method with the load inputting method of dynamic finite element method, such factors as the decay of seismic wave along its way of propagation, the frequency. amplitude. the phase difference of seismic wave, etc., can all be taken into account in analysis of the dynamic stability of slope.

Jan 1, 1999

By Charles H. White

Methods in colorimetry are based on the assumption that the intensity of the&apos; color of a definite volume .of solution is directly proportional to the quantity of the color-producing substance present. In the preparation and examination of colored solutions there are three ways in which the depth of color may be varied. These variables are : (1) the quantity of&apos; the coloring matter; (2) the quantity of the solvent, or the dilution ; and (3) the thickness or depth of that portion of the solution examined. With these three variables as a basis, three general methods in colorimetry have been devised, all of which have been used in the determination of carbon in steel. In the first method, the quantity of the solution is kept the same for both the unknown steel and the standard, and the sections compared are of equal thickness, while the quantity of the standard is varied until the color obtained is of the same intensity as that produced by a definite quantity of the unknown steel. In laboratories where this method is used there is prepared and kept for permanent use a series of solutions with varying amounts of the standard, representing the percentages of carbon from the lowest to the highest demanded in that laboratory. These standard solutions are kept in bottles or test-tubes of equal diameter, and are arranged in series from the faintest to the most intense color, so that it is a simple matter to find the place of the unknown steel in the series, when the solution is of a definite volume and is contained in a tube of the same diameter as the standard tubes. In the second method, equal quantities of the standard and of the unknown steel are dissolved, the standard is diluted to a definite volume, and the solution of the unknown steel is di-

Jan 1, 1907

By A. J. Griest, P. D. Frost, H. A. Robinson

The flow characteristics and uniform elongation of alpha-beta titanium alloys in the solution-treated condition were shown to be markedly affected by the solution temperature. Two classes of alpha-beta alloys were distinguished, based on the effect of solution temperature on the uniform elongation. Martensitic alpha-beta alloys, which are relatively weakly beta-stabilized, showed decreasing values of uniform elongation as the solution temperature was initially increased. However, after solution-treatment at still higher temperatures in the alpha-beta field, the uniform elongation of these alloys was again high, and often attained its maximum value. Nonmartensitic alpha-beta alloys, which are more heavily beta-stabilized, showed a continuous decrease of uniform elongation with increasing solution temperature. The behavior was rationalized in terms of the alpha-beta ratio and the alloy content of the beta existing at the solution temperature. The data indicate that in commercial practice close temperature control may be required to get maximum uniform elongotion, and hence, maximum potential formability, in solution-treated sheet. Bend-test data also were obtained for the solution-treated conditions. A MOST important objective of current titanium research is the development of age-hardenable alloys with superior formability in the solution -treated condition. Alpha-beta titanium alloys have been shown to be amenable to high-strength aging treatments after solution-treatment in the alpha-beta field.&apos; However, heat-treatment data on the properties of solution-treated sheet, such as uniform elongation, minimum bend radius, and flow properties, which have a bearing on the potential formability, have not been widely available. This paper presents only the most significant results of a research program conducted at Battelle for the Air Force in an effort to develop sheet alloys that can be formed readily as solution-treated and subsequently aged to very high strengths. Data for 10 compositions representative of the more than 25 alloys studied in this program are presented. A primary objective of the paper is to demonstrate the pronounced dependence of the flow characteristics and uniform elongation on solution-treatment temperature. This effect is believed to be vitally important in the commercial heat-treatment of age-hardenable titanium sheet alloys. Experimental Procedures Melting and Fabrication—The nominal and actual compositions, beta transi temperatures, and rolling temperatures of 10 of the 30 alloys studied are presented in Table I. Stock :€or two of the alloys, E (Ti- 8Mn) and J (Ti-6A1-4V) was obtained from commercial heats. The remaining heats, except D and I, were double melted as 10-lb heats in a consumable-electrode furnace. Melting stock was 120 Brine11 hardness sponge. The oxygen and hydrogen analyses spotted throughout the heats indicate the range of interstitial levels resulting from the melting practice used. Heats D and I were melted as 20-lb ingots with the same grade of sponge. These ingots were cut in half and one portion used in the present evaluation. The ingots, which were about 4 in. diam and 4 in. in height, were upset forged and drawn at 1750°F to sheet bar 5/8 in. thick by 2 1/2 in. wide in such a manner that the top of the ingot corresponded to the top of the sheet bar. Slabs of the sheet bar, 5 1/2 in. in length were scalped to 1/2 in. thickness and rolled at the temperatures indicated in Table I to approximately 0.055 in. sheet. Elongation during rolling took place at 90" to the original forged length. The fabrication procedure used is described in some detail since the experimental heats showed considerable directionality in mechanical properties. The rolling procedures for the commercial heats were unknown, but were such as to produce essentially isotropic properties. All heats, as rolled, showed microstructures typical of alpha-beta alloys worked in the alpha-beta field; that is, the structures consisted of equiaxed alpha particles in a beta matrix. Heat Treatment— The effects of solution and aging heat-treatments on the properties of the alloys were evaluated uSing longitudinal and transverse tensile and bend coupons sheared from the sheet. Two or three solution-treated conditions were evaluated for each alloy. In addition, the alloys were also tested after annealing at 1200°F for 4 hr and furnace cooling. The solution-treated and annealed conditions were those in which the alloys might be expected to

Jan 1, 1959