Search Documents

By Yi-Shen Li

This report has been prepared by Lockheed Missiles & Space Company, Inc. (LMSC), under United States Bureau of Mines Contract No. H0220040 dated 21 June 1972 for the design, development, fabrication, and certification of the One-Hour Self-Rescue Breathing Apparatus (PBA). The PBA is a self-contained, oxygen-generating, CO2-removing closed-loop breathing apparatus that provides a minimum of 1 hour of breathable atmosphere during escape from a mine with a contaminated or oxygen-deficient atmosphere. This Cost-Plus-Fixed-Fee (CPFF) contract has been successfully completed in a three-phase program. The Phase I tasks included the design, development, and fabrication of prototype units developed at LMSC in accordance with the requirement of the Code of Federal Regulations (CFR) Title 30, Chapter 1, Subchapter B, Part 11 (Appendix A), and was submitted to the National Institute for Occupational Safety and Health (NIOSH) for joint NIOSH and Bureau of Mines certification testing.

Jan 1, 1974

By Don K. Smith

The Reclamation Program for the Northern Zone of the Indus Plains in West Pakistan involves the construction of 30,000 irrigation wells to serve 20 million acres with an annual pumpage of nearly 40 million acre-ft. Detailed hydrologic studies indicated that mild steel would be satisfactory for casing; however, within two years after construction, about 10% of the wells began to fail due to encrustation and corrosion of the casing. A search to find a noncor-rosive substitute for the steel casing disclosed that only fiberglass-reinforced plastic pipe satisfied all requirements. The results of initial use of fiberglass have been highly satisfactory and have resulted in a lower over-all well cost. Advances in technology pomise further reduction in prices and improvement in performance. The northern zone of the Indus Basin comprises a vast area of essentially level land in West Pakistan which is irrigated by means of a complex system of canals that distribute more water to more land than any other irrigation system in the world. In spite of the development of this extensive irrigation system, production of food and fiber has not met the requirements of the country. The major reasons that crop production has not reached anticipated levels are the lack of adequate irrigation supplies and effective subsurface drainage. As a result, yields per acre are among the lowest in the world for areas where irrigation is practiced, and many thousands of acres of valuable crop land have been removed from production or seriously affected by salinity and waterlogging. To rectify the problems of irrigation supply and drainage the Government of Pakistan has undertaken a program of Salinity Control and Reclamation which is being administered by the Water and Power Development Authority. The Authority retained Tipton and Kalmbach, Inc., of Denver, Colo., as engineers for the program in the northern zone of the Indus Basin. This program consists of the construction of about 30,000 irrigation wells to provide drainage for waterlogged lands and full irrigation supplies, including leaching requirements, for all cultivated lands. The program will ultimately ensure the productivity of 20 million acres and involve an annual pumpage from groundwater storage of nearly 40 million acre-ft of

Jan 1, 1970

In this paper, a mixed integer linear programming (MILP) model for the short-term scheduling of open pit mines is formulated. The proposed model aims at sequencing the blocks extraction over multiple short-term periods. The model takes into account multiple processes, waste dumps, and multiple stockpiles. The short-term scheduler makes a decision on the period, destination, and route that ore and waste are supposed to take to minimize costs while meeting all the mining and processing constraints. The destinations of the extracted materials are also controlled by their rock types. A monthly short-term production scheduling case study of an iron ore deposit is carried out over a year to validate the model.

Jan 1, 2011

By M. M. Rajkovich, L. Adams, J. J. Zaluski, S. Gardner

In 1998, Kentuckians for the Commonwealth filed an Administrative Petition with the Kentucky Natural Resources and Environmental Protection Cabinet to designate 8,903 +/- hectares (22,000 +/- acres) on Black Mountain, which contains the state’s highest point, as unsuitable for mining. A fast track legislative process was triggered which could have "taken"100 million tons of coal reserves or, in the alternative, imposed severe restrictions on mining. Even with all parties represented by reasonable individuals, this process can be extremely cumbersome and expensive. The legal and technical preparation for this unusual hearing process as well as issues and strategies of the negotiated resolution are reviewed.

Jan 1, 2000

Mining in the twenty-first century brings with it a new range of challenges, some unfamiliar to our industry. Skilled staff recruitment and retention is a significant issue. Equipment supply lead times are changing the risk profile under which we operate. And the new landscape of this century demands accountability at all levels while also requiring that we deliver more to our shareholders and our host communities. This paper draws on experiences in Waihi, addresses some of the challenges facing the modern mining industry and suggests some modest mitigation strategies.

Jan 1, 2007

By Harold L. Kike

Until recently sulphur uses were so broadly based that economists used sulphur consumption to measure industrial activity. However, sulphur use patterns are changing and the manufacture of phosphate fertilizers presently accounts for approximately 65% of the world's sulphur consumption compared with only 25% in 1960. This has encouraged the development of new agricultural and industrial uses for sulphur. Major emphasis has been placed on its use as a fertilizer and in the manufacture of paving materials, specialty concretes and coatings. Some of these uses could have a significant impact on future sulphur usage.

Jan 1, 1986

Maximising margins in today's competitive international commodity markets demands superior productivity. This requires more than selecting the best equipment. It requires continually improving the efficiency of production, commercial, marketing and administrative processes under the control of solid modern management systems.This paper introduces an integrated way of working that includes proven management systems for successfully changing work practices and attitudes, developing managers and increasing accountability. It introduces a proven methodology for systematically involving people in sustained true continuous improvement of processes for maximising productivity, safety and revenue while minimising costs.

Jan 1, 1998

By J. Mark Richardson

Modern mining operations are increasingly affected by complex economic factors. Broad and rapid fluctuations in metal prices, rising operating costs, socio-political trends and the inherent technical difficulties encountered in most operations, all can combine to quickly change once-profitable ventures into money-losing propositions. Accurate knowledge of metal inventories during all phases of an operation has become essential to wise management decision-making. This paper reviews key elements of metallurgical accounting: sampling theory, measurement technology and computerized data adjustment. Application of current technology to the reconciliation of a hypothetical operation is discussed.

Jan 1, 1991

By N. R. Paterson, D. A. MacFadyen

A late-1980 airborne EM/magnetic method test over the State Line kimberlite area of Colorado-Wyoming shows weak but recognizable anomalous responses to the known pipes. The magnetic survey indicates the presence of several shallow subsurface bodies adjacent to the known kimberlites, which are interpreted as possible blind diatremes. The survey data, in profile and contoured map form, has been correlated with geological map information available at the time. It can serve as the basis for reexamining kimberlite distribution in the area, taking into account geological findings during the recent work on known bodies.

Jan 1, 1987

By Gustaf Ising

For relative gravity measurements, the author in 1918 described an instrument1 of which the essential part consists of a highly astatized, standing pendulum turning about a horizontal elastic axis. This type of instrument has been used recently in practical field work, therefore a description of its principle and technical development is given herein. Part I, describing the principle, is a direct translation of the original Swedish paper.1 Part II gives an account of the practical elaboration of the instrument, together with some description of measure-ments performed.

Jan 1, 1937

By J. O. Brittain, E. Lautenschlager

An investigation was conducted on fine grained airon wire to measure the influence of the temperature of deformation on strain aging near room temperature. Specimens were deformed various amounts at 77°, 195°, or 273°K and aged. The strain aging was followed by either internal friction or return of the yield-point measurements. The results show that strain aging occurs in three stages. During the first stage there is small, almost immediate return of the yield point. The solute carbon concentration, as mesured by internal friction, remains constant in stage I but is lower than the concentration in the unstrained condition. In the second stage, the solute concentration decreases while the magnitude of the yield point increases. In the third stage, the solute atoms continue to drain from the solution, the yield point approaches a maximum, and the strain-hardening coefficient and flow curve increase. The kinetics of the strain aging reaction are not the same for the two sets of measurements since the internal friction results lag behind the yield-point measurements. However, the strain-aging kinetics measured at 44° and 64°C showed no effect due to the difference in initial deformation temperature; nor were the strain aging kinetics influenced by low-temperature anneals at 77°, 195°, and 273°K. 1 HE object of this investigation was to measure the effect of initial deformation temperature on the strain aging of a-iron by tensile tests (i.e., return of the yield point) and internal friction methods, to correlate the results of the two measuring methods, and to measure the effect of low-temperature annealing (<273°K) after low-temperature deformation upon strain aging. The experiments were performed on fine-grained a-iron wire containing 0.02 wt pct c.l According to Thomas and Leak,&apos; return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solid solution, while the return of the yield point as a function of the aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,3 during aging the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point on subsequent testing. It has been shown that after low-temperature neutron bombardment, a-iron goes through a stage of recovery at low temperatures which can be attributed to the annealing of iron interstitials&apos; and/or vacancies.4 If, after low-temperature deformation, there is an interaction during a low-temperature anneal between mobile point defects and the solute atoms (i.e., carbon atom interaction with vacancy or iron interstitial), it is possible that some solute atoms will be found at defect sites other than dislocations. Such changes in the sinks for the carbon atoms might be expected to alter the strain-aging kinetics sufficiently to be detected by either inter-

Jan 1, 1962

Improve the efficiency of stainless steel pickling (chemically cleaning) operations by providing the industry a quick and convenient method to estimate pickling solution behavior and to estimate recommended ranges of nitric and hydrofluoric acid concentrations for effective pickling of stainless steels. Background Iron, chromium, and nickel in stainless steels react with nitric and hydrofluoric acids during pickling. Ions of these dissolved metals complex or combine with the acid anions. When the total metal concentration reaches about, 50 grams per liter of pickling solution, the solution no longer serves its purpose and is considered spent. Knowledge of cation and anion species in these pickling solutions contributes an insight into pickling chemistry and allows estimates to be made of the most effective ranges of acid concentrations. The Bureau developed a computational model of the complex equilibrium chemistry occurring among iron, chromium, and nickel and the pickling solution. Total concentrations, in grams per liter, of nitrate, fluoride, iron, chromium, and nickel were used as input; output was 17 cation and anion molar concentrations. The model, in the form (if an equilibrium program on a mainframe computer, was used extensively to facilitate Bureau research by determining chemical complexes in numerous stainless steel pickling solutions. However, the program&apos;s availability to members of the stainless steel industry, its intended users, was limited because of lack of mainframe compatibility and the difficulty of program maintenance.

Jan 1, 1989

The concepts of capacity and basicity have proved extremely useful in dealing with a wide range of solute species in metallurgical slags, and as a result have been widely applied. These two concepts are reviewed, and it is suggested that the Lewis approach to basicity has much to commend it. In some cases, it appears that the term capacity has been used without due consideration being given to the nature of the solution being formed, or even to whether a true solution was being formed at all. This paper proposes a rigorous definition of capacity, based on the true nature of the solution process in slags and glasses, and briefly reviews the repercussions of this approach on data available in the literature and the limitations which it may impose on future investigations in this area.

Jan 1, 1994

By Robert Mehl

THE precipitation of the nitride Fe4N from the solid solution of nitrogen in a Fe and of the phosphide Fe3P from the solid solution of phosphorus in a Fe both lead to the formation of structures that may be easily identified as Widmanstätten figures, within the meaning of the term as used in this series of papers. A complete solution has been obtained for the figure formed by Fe4N. The structure of Fe,P, however, is not fully known and a complete solution of this figure thus cannot be obtained; nevertheless, a study of this figure has furnished some new information. PRECIPITATION OF FE4N FROM ALPHA SOLID SOLUTION OF N IN ALPHA FE Constitution of System Iron-nitrogen A knowledge of the constitution of the whole of the Fe-N system is unnecessary for this work, though the recent studies by Eisenhut and Kaupp1 and by Lehrer2 have clarified most of the moot points; it is sufficient for our purpose to state that a Fe of high purity dissolves 0.42 per cent of nitrogen in solid solution at the eutectoid temperature, 591° C., and that this solubility decreases at first rapidly and then more slowly until at room temperature the solid solubility amounts to approximately 0.1 per cent nitrogen.3

Jan 1, 1934

By P. A. Mahanwar

Flyash were melt mixed with nylon 6 at a 30wt% concentration. TYZOR® TPT, a coupling agent, was used to facilitate the link between filler and matrix. The morphological characterization, using SEM, revealed sufficient matrix residue on the filler surfaces thus confirming the strong interfacial bonding between the filler and the matrix on treating. Tensile, impact and the flexural properties of the composites were also improved with the incorporation of coupling agent. As flyash particles tend to impart a grayish color to the plastic, TiO2 pigment was employed to make the formulations aesthetic. The pigment was added to the filled system in 0.1, 0.5, 1.0, 1.5, 2.0 wt/wt ratios. Scattering of incident light and spectral reflectance was higher for smaller particle size flyash. Moreover an increase in the scattering with increase in pigment concentration indicates better dispersion of the pigment, which again is due to the presence of coupling agent.

Jan 1, 2006

By D’Arcy A. Shock

In this year&apos;s review, the concept of solution mining has been expanded to include total solution as well as the technology of leaching, or partial solution methods. Leaching methods continue to make strides in the processing of metallic minerals, particularly in copper and uranium production. No quantitative data are available on the increase of leach operations; however, it is known that there were more systems installed in 1969 and that the estimated 15% of U.S. domestic production of copper produced in 1968 was by leach methods.1 While the number of publications appearing during the year were few,2,3 there were special sessions in this field at the AIME Annual Meeting and SME Fall Meeting in 1969 and more scheduled for these meetings in 1970. Significant areas that should be mentioned are: the continuing interest in bacteria to convert sulfide sulfur to acid thus reducing reagent costs in both copper and uranium sulfide ores, the exploration of leaching agents other than common mineral acids or alkaline solutions,4,5 kinetic studies of leach mechanisms and the development of microfractures for increased leach solution penetration by use of chemical or atomic explosives.6,7

Jan 1, 1970

By H. S. Jerabek, Charles S. Barrett, Robert F. Mehl

The precipitation of the nitride Fe4N from the solid solution of nitrogen in a Fe and of the phosphide Fe3P from the solid solution of phosphorus in a Fe both lead to the formation of structures that may be easily identified as Widmanstatten figures, within the meaning of the term as used in this series of papers. A complete solution has been obtained for the figure formed by Fe4N. The structure of Fe3P, however, is not fully known and a complete solution of this figure thus cannot be obtained; nevertheless, a study of this figure has furnished some new information. Precipitation of Fe4N from Alpha Solid Solution of N in Alpha Fe Constitution of System Iron-nitrogen A knowledge of the constitution of the whole of the Fe-N system is unnecessary for this work, though the recent studies by Eisenhut and Kauppl and by Lehrerz have clarified most of the moot points; it is sufficient for our purpose to state that a Fe of high purity dissolves 0.42 per cent of nitrogen in solid solution at the eutectoid temperature, 591&apos; C., and that this solubility decreases at first rapidly and then more slowly until at room temperature the solid solubility amounts to approximately 0.1 per cent nitrogen.3

Jan 1, 1934

It is argued that the capture of par- ticles by bubbles is primarily caused by hydrophobic ("structural") attraction forces. Neither dispersion forces nor double-layer forces can account for hydro- phobicity, though the latter are known to influence the kinetics of capture. The recent experiments of Israelachvili and Pashley (Nature, 300: 341-342, 1982) with hydrophobic mica plates provide the first measurements of the range and magni- tude of hydrophobic interaction forces.

Jan 1, 1984

By R. G. Reddy

Nickel solubilities in spent pickling solutions (i.e. HF-HNO3-H2O solutions ) were measured as a function of HF and HNO3 acid concentrations. The chemical analysis of the industrial pickling solutions and sludges were made. The stable phases observed in the sludges are FeF3?3H2O, and ( FeCr ) F3?3H2O. Pure Ni, and stainless steel type 316 were used in this study. The results showed that the solubility of Ni increased with increase in concentrations of HF in pickling solution at a fixed concentration of HNO3: An excellent agreement between the experimental solubility data and the theoretical data was obtained. X-ray diffraction analysis showed that the solid solubility product formed is mainly NiF2?4H2O compound.

Jan 1, 1992

By S. Mellgren, W. Opie

AN equilibrium state of importance in the process of electrolytically depositing titanium from fused chloride electrolytes is that which exists between titanium metal, titanium dichloride, and titanium trichloride. This can be expressed by the reaction titanium concentration of the solution, temperature, and the proportion of strontium chloride and sodium chloride in the solution. Procedure The general procedure used consisted of the following steps: 1) Development of an analytical method for determining Ti+2 and total titanium. 2) Preparation of batches of fused salt solutions containing various amounts of total titanium, Ti+2 and Ti+3 3) Blending of the prepared batches and excess titanium metal in Vycor tubes and allowing the solutions to come to equilibrium. By blending, solutions with different total titanium content could be prepared and equilibrium could be approached from the high Ti+2 and low Ti+2 sides. 4) Studying the effect of titanium concentration, temperature, and the mole ratio of the solvent chlorides, SrC1, and NaC1, upon the equilibrium.

Jan 1, 1958