Search Documents

By John D. Carr

Introduction The Flin Flon zinc plant operates on what is known as the low density or standard sulphate process, that is, the zinc is carried through the plant solution circuit attached to the SO4 or sulphate radical at a concentration not exceeding 175 grams per litre zinc. The process may be described briefly as follows: The zinc is received in the zinc concentrate chemically combined with sulphur and mixed with many other impurities. The concentrate is roasted and most of the sulphur is burned to a gas, which is discharged from the plant. The roasted concentrate, or calcine as it is called, is leached with a weak sulphuric acid solution so that the resulting leach solution contains a high zinc content but a very small proportion of the impurities. The solution is separated from the solids and is purified further by agitation with zinc dust to remove copper, cadmium, and cobalt. This purified zinc sulphate solution is then pumped to the electrolytic department. The solids from the first leach are again leached, but this time with a stronger acid solution to dissolve all of the remaining zinc which is soluble in the strength of acid available. The solids and solution from the leach are then separated. The solids are stock-piled for further treatment at some future date and the solution, carrying a relatively high amount of impurities, is sent to the first leach, where the chemical action is such that the contained impurities are precipitated as solids. The electrolytic department is nothing more than a large number of electroplating cells in which the zinc is plated on aluminium sheets. Since zinc does not plate tightly to aluminium, the zinc plating or sheet is easily stripped from the aluminium and the sheets are collected to be melted and cast into the standard market bars or slabs. In the electro-deposition cells, the zinc sulphate (ZnS04) is split to metallic zinc (Zn) which plates out, and sulphate (S04) which combines with the hydrogen of the water of the solution to form sulphuric acid (H2S04). When one pound of zinc is deposited, about one and one-half pounds of sulphuric acid are formed. This acid is sent to the leaching section, where it dissolves one pound of zinc from the calcine. The solution is purified and is again pumped to the plating cells. The solution travel forms a complete circuit.

Jan 1, 1935

By S Wainio, P J. Beckett, T Miller

Lichens are a symbiosis of fungi and algae. Air borne elements and gases are absorbed very efficiently over the entire surface of the lichen, because they have no protective structures such as a waxy cuticle or stomata. A survey in 1977 (one year before the Sudbury Regreening program began), indicated that several Cladonia spp had invaded the soil in Sudbury’s open birch woodlands. Pollution sensitive species such as Cladonia rangiferina and C. mitis occurred 20–25 km from the smelters. It was anticipated that the improvements in air quality and reclamation efforts would allow a natural invasion of pollution sensitive species into what once was a lichen desert that surrounded the smelters. The purpose of this project was to study the invasion of terricolous (soil-inhabiting) communities of lichens and mosses on reclaimed land in the Sudbury region 45 years after commencement of the Sudbury Regreening Program.

Aug 2, 2023

By Lloyd H. Yeager

Good morning gentlemen. I'm very pleased to be a part of this fine program for the Society of Mining Engineers. Gypsum, as many of you know, is one of the most unique minerals on earth. The very excellent presentations which you have just witnessed, revealed the geological aspects of gypsum operations. It is not our purpose this morning to pursue this subject further. Instead, we felt you would be interested in some of the uses of gypsum . . . and what the future holds for gypsum products. To help accomplish this, we're going to first show the Gypsum Association's new film, "Shape Of The Future. ' This short movie traces gypsum f ram mines and quarries to its ultimate destination in homes, schools, offices -- in virtually every type of construction. We think you'll be particularly interested in the description of gypsum's fire resistive nature.

Jan 1, 1965

The following thesis is an outcome of an investigation undertaken by the writer, at the suggestion of Professor Skeats, of the dykes and associated auriferous reefs of the Walhalla-Wood's Point belt, with the view of determining what relation, if any, existed between the petrological nature and the extent of llietasomatic alteration undergone by the dykes, and the genesis and localization of the gold.Although the greater part of the writer's time in the field and laboratory was occupied in studying the dykes and auriferous occurrences, a study was also made of the general geology as a basis for the special investigation. In addition, it soon became evident in the field that secondary enrichment had played a marked part in re-concentrating the gold and some interesting data in this connection have been collected. For example, indubitable evidence has been found of nuggets of gold having been formed by secondary processes.

Jan 1, 1920

By SAMUEL GOMPERS

THE name engineer makes a very strong appeal to one who appreciates the mechanism underlying the fabric of our civilization. Engineers are scouts of civilization. We send them ahead into the lone 'places-the wilderness, the jungles, the great watery expanses, to build the highways necessary for civilized man. The engineers must deal with Nature, with that mysterious dynamic thing we call "force," with materials. It is their function to direct the human activity necessary to coordinate these forces and material in order to make them serve the needs and aspirations of men. Because of my high conception of the engineering profession I was glad to accept the invitation to address The American Society of Mechanical Engineers to voice my understanding of the possibilities of your work as engineers of industry, and to suggest what seems to me the responsibility of the-engineer to the whole modern industrial system.

Jan 1, 1921

By E. R. MARBLE

THE introduction of a new fuel, such as natural gas, necessitates careful study where it has not been used previously. At the El Paso smelter natural gas required the installation of apparatus with which no one at the plant was familiar, either as to the type of equipment needed or as to the burning of the gas in it. Observation of existing installations of a similar character and assistance from gas engineers served as a basis to determine what was advisable to use. The gas line entering the plant goes to a metering station equipped with a duplicate system of pressure regulators, a temperature recorder and the gas company and smelter orifice meters in tandem. There are three distribution lines that can be inter-connected at a later date, if necessary, to assist in equalizing the plant load. All the larger lines are of heavy

Jan 1, 1930

By Gabriel Bartholazzi Lugão de Carvalho, Sergio Neves Monteiro, Fabio Da Costa Garcia Filho

The thermochemical treatment of Pulsed Plasma Nitriding is employed as an alternative to improve the surface properties of metals, such as: increase surface hardness, improve wear resistance, extend fatigue life and also create a barrier to the diffusion of hydrogen into the steel to reduce the susceptibility to hydrogen embrittlement. In this study, the effect of such treatment on ASTM A36 steel is analyzed through two different nitriding conditions: 5 h and 660 Pa for the first condition and 15 h and 720 Pa for the second one. In both cases, the temperature was held at 300 °C. Thus, in order to verify the results, Vickers hardness analysis and metallographic observation were carried out under an optical microscope. Only the second condition was able to achieve what was proposed, the formation of a uniform nitriding layer and an expressive increase of hardening on the surface.

Mar 1, 2018

By R. E. Wagner

MISSOURI's famous lead area, in what is known as Southeast Missouri, is locally termed the "Lead Belt." These deposits are in the Bonne Terre dolomite of late Cambrian age which has a thickness of nearly 400 ft. Underlying this is the La Motte sandstone which varies in thickness from 0 to 400 ft. The La Motte beds are deposited directly on the ancient erosion surface of Pre-Cambrian porphyries and granites of probably Algonkian age. The buried igneous peaks extend up into the Bonne Terre in several areas within the Lead Belt. Overlying the Bonne Terre are shales and siliceous dolomites of late Cambrian and early Ordovician age. Within the Lead Belt these have a thickness of from 0 to 500 ft. The district is bounded in general on the southwest by the Sims Mountain fault, on the northwest and north by the Big River fault, and on the

Jan 1, 1947

By Walter Miller

ALTHOUGH confident of its ability to meet any demands which may be made, the petroleum refining industry is not complacent about the situation and realizes that the quantities of petroleum products to be furnished are so enormous and so far beyond what was previously estimated that the full co-operative effort of the industry must be exerted. Establishment by the President in May of the Office of Petroleum Coordinator for Defense with Secretary of the Interior Ickes at its head, plus the formation of the Petroleum Industry Council for Defense, in November, provide the channels for united endeavor within the industry and the means for gearing that endeavor within the industry and the means for gearing that endeavor in full harmony with the nation?s needs. Great strides have been made and a rapid understanding of the situation and the magnitude of the task is being attained by all concerned.

Jan 1, 1942

By Irwin H. Cornell

BRIEFLY stated, the history of the St. Joseph Lead Co. is the story of how a group of men, working for ten years as officers without salaries and stockholders without dividends, developed a small mine in Missouri into what became a large and prosperous corporation. Their courage and faith in the scattered surface deposits of lead coupled with the management's engineering vision and sound financial judgment should prove an inspiration to present-day mining operators and investors. In 1717, John Law's company, known as "The Company of the West," was formed in France and letters patent were granted, for a period of 25 years by Louis XV, for exploration in the Mississippi River Valley. One of the underlying purposes of the expedition, headed by Mr. Renault and Mr. La Motte, a French metallurgist, was development of the lead mines in the area now known as Southeast Missouri.

Jan 1, 1947

By Neil C. Hario

The purpose of this paper is to explore the various designs and design alternates available for large fine crushing plants, and to discuss objectives and criteria upon which these designs are founded. Common practice for size reduction of run-of-mine or run-of-pit ore in preparation for subsequent treatment utilizes a three-stage system. First stage, or primary breaking is generally carried out with jaw or gyratory crushers. The usual output from this stage provides a feed for fine crushing in the size range of 6 to 10 inches. This discussion is limited to the process of fine crushing, and we will further limit it to what is commonly called secondary and tertiary crushing. We define a large crushing plant as one with a minimum capacity of 2,000 tons per hour. Generally, these plants utilize cone type crushers to reduce ore for rod, ball, or pebble mill feed.

Jan 1, 1970

By Schneider, W. G.

IT is not my purpose to burden you with many statistics. The charts herewith should be considered merely as indicating the trend. I believe' that is what is really of interest to us. It is difficult, if not impossible to forecast with any assurance future developments, because of possible new mines, competitive materials, curtailment' or increase in the use of the metal in certain markets, and many other factors that have a vital bearing on any industry. Fig. 1 shows United States smeltet output of copper, starting with 1845. It is estimated that in 1928 the smelter output of copper will be about 1,010,000 tons. Between 1895 and 1905 it increased about 200,000 tons, and between 1905 and 1915 about 240,000 tons. Between 1915 and 1925 the increase was about 140,000 tons. This is an average increase over 30 years of about 190,00Q tons per ten-year period. At the present time the indications are that this demand for increased production will continue. As to whether or not we have the supplies or facilities to maintain this increase or a greater one, remains to be seen. Provided it is possible for United States smelters to increase their production, they should be producing at the rate of about 1,210,000 tons or more per year by 1935.

Jan 1, 1928

By G. B. Sazuyer

DEVELOPMENTS respecting beryllium during the past year have been sufficient to center attention on it as likely to be the most important of any of the chemical elements that have recently found a place for themselves in technical industry. This importance is only potential, however, largely because adequate supplies of beryllium ore will be necessary. The beryllium industry will be only as great as the mines which support it. To find and develop large mines will be the problem. Chief of the immediate commercial developments in the United States is beryllium-copper and its espousal by Anaconda and Riverside even at present high prices. According to the pamphlets of these companies, it ap¬pears that beryllium is to copper nearly what carbon is to iron. When one considers that the tensile strength of pure copper is about 33,000 lb. per sq. in., but that the addition of 1.5 to 2.5 per cent of beryllium produces a heat-treatable alloy with a maximum tensile strength of 220,000 lb. or over, the analogy to carbon and iron is made strikingly, clear. Striking among the properties of beryllium-copper is its resistance to fatigue, claimed to be equal or superior to that of spring steel. It needs little imagination to foresee a great industry for this alloy alone.

Jan 1, 1934

By Thomas M. Drown

Remarkable as have been the direct results of Danks's puddler, there are some indirect and incidental results, which are well worthy of study for their intrinsic value and suggestiveness. The success of Danks's machine is due mainly to the nature of the lining and the manner in which it is attached to the walls of the revolving chamber. Herein lies Danks's merit and good fortune. Given such a lining, and the success of the machine, as far as puddling iron is concerned, could easily be predicted. Other important results have, however, been obtained with this machine, which, though clearly explicable, were, nevertheless, unanticipated. These are the increased yield of bar-iron over the pig-iron charged, and the elimination of phosphorus, which, though not absolutely complete, is yet more decided than in the case of hand-puddling. As regards the increased yield, this is merely what we have a right to expect if we consider the puddling process to consist in the oxida tion of the carbon and silicon of the pig by the oxygen of the oxide of iron. That this result is attained, nearly to the extent that the theory requires, in Danks's puddler, and has never been more than partially attained by the most careful experiments in band-puddling, points clearly to the fact that the contact of the molten pig-iron with the oxide of iron is much more intimate and complete in the one instance than in the other. The action of puddling in Danks's machine may be considered to be twofold: first, the removal of the carbon, silicon, and phospho rus of the pig, which is the primary object, and, second, the produc tion of wrought iron direct from the ore, which is entirely an inci dental result. Intelligent metallurgists were not long in recognizing in this latter result a fact of deeper import and greater value than the attainment of a perfect puddling process. A new method

By Thomas M. Dr. Drown

REMARKABLE as have been the direct results of Danks's puddler, there are some indirect and incidental results, which are well worthy of study for their intrinsic value and suggestiveness. The success of Danks's machine is due mainly to the nature of the lining and the manner in which it is attached to the walls of the revolving chamber. Herein lies Danks's merit and good fortune. Given such a lining, and the success of the machine, as far as puddling iron is concerned, could easily be predicted. Other important results have, however, been obtained with this machine, which, though clearly explicable, were, nevertheless, unanticipated. These are the increased yield of bar-iron over the pig-iron charged, and the elimination of phosphorus, which, though not absolutely complete, is yet more decided than in the case of hand-puddling. As regards the increased yield, this is merely what we have a right to expect if we consider the puddling process to consist in the oxidation of the carbon and silicon of the pig by the oxygen of the oxide of iron. That this result is attained, nearly to the extent that the theory requires, in Danks's puddler, and has never been more than partially attained by the most careful experiments in hand-puddling, points clearly to the fact that the contact of the molten pig-iron with the oxide of iron is much more intimate and complete in the one instance than in the other. The action of puddling in Danks's machine may be considered to be twofold first, the removal of the carbon, silicon, and phosphorus of the pig, which is the primary object, and, second, the production of wrought iron direct from the ore, which is entirely an incidental result. Intelligent metallurgists were not long in recognizing in this latter result a fact of deeper import and greater value than the attainment of a perfect puddling process. A new method

Jan 1, 1874

By Allister McLeod

Coal is expected to play a major role in energy supply in the next 20 years. Oil is a convenient and still reasonably abundant fuel. However, its major sources of supply are regions where there is nervousness about political stability. Uranium is a more efficient fuel - but there is a continuing community apprehension regarding its use. What coal may lack in efficiency, it makes up in long term availability and competitive overall cost. Moreover, diversity of source ensures stable long-term supply. In this way, a major role for coal in the world energy scene is assured. Cyclical considerations aside, demand for coal will increase significantly and it will meet a substantial share of new energy demand, replacing oil and gas in major industrial and electric utility markets. By around the year 2000, coal's share of world energy could reach 30% and rival oil as the largest single source of energy.

Jan 1, 1982

By William J. Robinson

What is the cummulative rate of recovery of copper from a sulfide leach dump? This is one of the most frequently asked questions today. We, in the industry, ask it of each other when we meet; however, the technical answers may vary from "I don't know" to 'quite good" from people within the same company. Management also poses this question because it plays a vital role in our planning for future production. The answer is difficult because of the many variables between different operations such as physical construction of the dump, topography of the original site, characteristics of dump material, mineralization, water application, etc. Each has a bearing on the rate of recovery. OPERATIONAL DATA Our method of water distribution is unique in that each dump is drilled to allow physical injection of water into the dump. The in¬jection holes are drilled vertically, on 251 centers, from the surface of the dump. Normally, the holes are drilled 40' deep and cased with 4" PVC perforated pipe.. The pipe is perforated at one-foot intervals with four V diameter holes at 901 spacing on the pipe circumference. We formerly alternated shallow holes (20'-40') with deep holes (80'-l80') in an effort to cover the entire dump and hasten oxidation. The shallow hole depth varied according to the compaction thickness. The deep hole depth varied according to the height of the dump and the original ground profile, We prefer to have the deep holes end 20'-30' above the original ground level. This generally allows us to penetrate the coarse material at the bottom of the dump. We had to discontinue the deep holes_ in order to cover more dump area in a shorter period of time to meet increased production requirements.

Jan 1, 1972

A. H. Bromly, Zihuatanejo, Guerrero, Mexico (communication to the Secretary*):—The following criticism of what "is offered as a summary which may be found useful by mining engineers," is not dictated by any captious spirit, but in the intereet of historical and scientific accuracy. The States of Queretaro and Oaxaca have produced sufficient silver to warrant more extended notice. Referring to Pachuca, State of Hidalgo, the eomewhat loose and inexact statement is made that "the ore-depdsit is an andesite, intermixed with quartz-veins, rich from the surface." A better description mould be,—the ore-deposits consist of quartz-veins in andesite. It is notable that many of the rich shoots worked in recent days did not come to surface. In consequence, Pachuca is often quoted by the ill-informed as a camp in which values improve with depth, the truth being that the veins carry shoots, or clavos, some of which were exposed at surface and some not. The name of " electric plow," applied to the mechanical stirrer of recent use, is certainly not to be recommended. The stirrer, or agitator, consists essentially of a traversing gang-plow, operated by power through shafting; drums, and wire-rope. The fact that in certain plants the motive-power used is electricity does not make it an electric plow. Such a name suggests a machine of which the motor is an essential and integral part; which is not so in this case. A lathe in a factory driven by water-power is not called a hydraulic lathe. My experience agrees with Dr. Raymond's note as to azulapue, which in some districts is also applied to blue copper carbonate. The El Oro, Esperanza, and Mexico mines should be allocated to the State of Mexico; the Dos Estrellas being in Michoacan, as stated. The El Oro quartz certainly does not appeal to me

Jan 1, 1910

By Edward O. Reinbold

The paper presents the results of a study which involved collection and analysis of airborne pollutant concentration data in two producing underground room and pillar metal mines which use diesel powered equipment in the area near the face. The results include the concentrations of CO2, CO, NO, NO2 and respirable particulate matter measured with the latest portable instruments, and the carbon and hydrogen contents of the particulate matter samples determined by combusting them in a Elemental Analyzer. The carbon and hydrogen contents are used to estimate the amount of diesel particulate matter in the mine ambient air. The short term grab sample concentration data, although not suitable for determining compliance with ACGIH Threshold Limit Values (TLVs), are related to the TLVs so that they may be compared conveniently. Lognormal frequency distributions and the arithmetic mean of the concentration measurement data are used to compare different mine situations. Conclusions are drawn as to which pollutants are most important to control under actual mine production conditions.

Jan 1, 1979

By Wilson Blake

This report presents the results of a 7-year Bureau of Mines program to review, revise, and make an effective engineering tool of the microseismic method of determining the stability of rock structures. The program consisted of developing new microseismic equipment and data analysis techniques and extensive field investigations to demonstrate the effectiveness and potential of the broad-band microseismic method. The guidelines for choosing the components of a microseismic system are presented along with approximate cost figures. Different microseismic systems are discussed, including completely automated systems. Procedures for conducting microseismic investigations and analyzing microseismic data are discussed in detail. Field situations which show the full value of the microseismic technique as an engineering tool are described.

Jan 1, 1974