Search Documents

Previous models describing the aggregation of polymer coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called ?active? sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1987

By G. H. Long, D. H. Magnusson

THE DEFINITION of the continental margin, as considered in this paper, is in the broad sense: " ... those provinces of the continents and of the oceans which are associated with the boundary between these two first-order features of the earth" (Heezen et aL, 1959, p. 17). The provinces in the area under con-sideration are: the Continental Shelf, the Continental Slope and the Continental Rise. The Continental Shelf extends from the shoreline to the shelf break, which lies at approximately the 200-meter isobath through-out the region (except north of the Grand Banks, where the break may be defined more properly by the 400-meter isobath). The Continental Slope and Rise occur between the shelf break and the 4,000-meter isobath. (The last figure was somewhat arbitrarily selected for the purpose of this paper.) The Atlantic Continental Margin as thus defined extends along the eastern coast of Canada from the International Boundary in the Gulf of Maine northward to approximately the 60°N latitude off the coast of Labrador. The area of study amounts to at }east 500,000 square miles -an area roughly equivalent to 13 per cent of Canada's total land surface.

Jan 1, 1970

By Andrew Thomson, Peter Wright

"A section of a London Underground expanded segmental lined tunnel constructed in the 1970’s progressively deteriorated after 2001, with extensive radial joint spalling and mid-segment cracking. As part of the PPP contract Tube Lines Ltd and their partners carried out various analyses of the tunnel, including analysis of laser scans of the tunnel, geotechnical testing through the tunnel walls, geotechnical desk studies, real-time monitoring and even full-scale segment testing. This paper discusses the behaviour of the tunnel lining in this setting, the causes of failure and the lessons that can be learnt from this rare example of a tunnel which was progressively failing in service. It is finally noted that a replacement tunnel lining was installed during night-time possessions and completed in 2015. INTRODUCTION In 2003, Tube Lines Ltd. was established under a Public-Private Partnership (PPP) scheme to provide maintenance services and upgrade projects for London Underground (LU). The Deep Tube Tunnel Knowledge and Inspection Programme comprised the assessment of all tunnels, shafts and other underground structures. This included a number of lengths of tunnel constructed using segmental concrete linings. First used by LU in the 1960s, the savings both in cost and speed of construction led to concrete linings replacing cast iron for new tunnel construction in all but a few cases. During the initial scoping phase of this programme, inspections identified potential issues with the expanded concrete segmental linings on the Jubilee line. The inspections found a number of segments with surface spalling (Figure 1a), which did not appear on the post-construction defect records. These were generally relatively shallow, up to 40mm deep, spread over a wide area of segment. These were different to spalls caused by handling damage, which are typically localised at segment corners. Subsequent inspections over the following years identified an increasing number of segments with these types of spalls as well as an increased incidence of longitudinal mid-segment cracking (Figure 1b). The increasing occurrence of these defects was hypothesised to be caused by tensile stresses developing in the vicinity of the joint."

Jan 1, 2016

By D. P. Ziegler

Formulas relating economic optimum busbar cross sectional areas to busbar cost, electric price and financial parameters are reviewed and revised. Application of the formulas is illustrated with discussion of the appropriate choice of parameter values and the sensitivity of the optimum to the parameters. The extension of the single busbar concept to optimization of more complicated arrangements of bus for smelting pots is complicated by the constraint of obtaining a specified current distribution. An example problem illustrates the optimization of a section of a bus network containing a fork, with the imposed limitation of achieving a specified uniformity in the current. In cases where the current in the individual conductors may vary, Kelvin's law does not apply. Further extension of the technique to a full pot set of conductors poses additional problems which are discussed, but whose solution has not yet been accomplished. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By H. M. Chance

Jan 1, 1887

Barrick Gold Corporation is the gold industry leader, with 25 operating mines and a pipeline of large, long-life projects located across five continents, in addition to large land positions on some of the most prolific mineral districts. Barrick's high level of commitment to sustainable economic development and environmental stewardship was recognized by Dow Jones Sustainability Index (DJSI) - World, for the third consecutive year in 2010. The potential for adverse environmental effects from acid rock drainage (ARD) and metals leaching (ML) and their financial implications for Barrick are key considerations in our environmental assessment and business development processes. Barrick's membership in the International Network for Acid Prevention (INAP) reflects the importance of these issues to our business. INAP's development of the Global Acid Rock Drainage (GARD) Guide (a best practices guide for acid rock drainage prevention) provides Barrick with an important tool to assist in the assessment of environmental and financial risks from ARD and ML associated with our planned and ongoing mining operations (INAP, 2009). In this paper we will discuss how Barrick incorporates the GARDGuide and its principles for ARD and ML prediction and prevention in our business development processes and the management of our operations. The GARDGuide serves as a key reference for our project environmental assessments and as a common link between our projects and operations management, consulting specialists, permitting and regulatory authorities and the public. We will discuss how the GARDGuide is being "syndicated" throughout Barrick as a standard of practice and present a case study of how it was used in a recent Barrick Business Development Project.

Jan 1, 2011

By R. H. Hanewald

The processing of EAF baghouse dusts from both the specialty steel industry and low alloy producers will be reviewed. In addition, the INMETCO process has been modified so as to recover nickel, chromium and iron from many other waste materials such as pickling solutions or filter cakes, spent nickel and chromium plating baths, carbon refractories from pickling tanks, and super alloy wastes including baghouse bags. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high temperature metals recovery. This, along with the details of INMETCO's BDAT Test Program and results performed to pre-agreed standards with the EPA will be discussed.

Jan 1, 1992

The National Mining Hall of Fame and Museum (NMHF&M) will celebrate its 25th anniversary on Sept. 22, 2012 when the 2012 class is inducted during a special ceremony in Las Vegas, NV in conjunction with MINExpo 2012. The NMHF&M will induct four men representing the equipment manufacturing, minerals exploration, copper and coal sectors of the mining industry. The diverse cross-section of mining industry giants joining the hall of fame include Glen A. Barton, J. David Lowell, Samuel Newhouse and John Cleveland Osgood. They will join 214 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 25th Silver Anniversary Induction Banquet & Ceremony. These men were selected for being visionaries, leaders and ambassadors within their own sectors and across the industry at large.

Jan 1, 2013

By Nicholas C. Williams

This paper presents the development of a demand reduction and responsive strategy capable of reducing the electrical power demand, particularly during peak conditions. The work presented includes a case study of a UK colliery. Areas explained are the equipment installation at the mine; the development of the demand reduction strategy including the load profile database and prediction optimisation model. Some live production data from the power meter installation at the mine is also presented.

Aug 1, 2013

By Becket, Frederick M.

CHROMIUM is but one hundred and thirty years of age-a mere youngster as related to many metals that' have speeded world progress. It was Vauquelin of France who proved conclusively that the so called red lead of. Siberia contained a new element. The variety and characteristic colors of the compounds suggested the name chromium. He also succeeded in reducing oxide of chromium to the metallic form and described the product as very brittle, infusible, needle- like crystals on which acids had very feeble action. His metal was not pure chromium, of course; it must have contained appreciable carbon in the combined form as a result of reducing the oxide by carbon at high temperatures. Vauquelin's description in 1798 of this work is a gem-indeed, literally, he went so far as to discover the presence of chromium oxide in the emerald. The metallic product did not seem to interest Vauquelin greatly, but a new chemical industry began shortly after his discoveries.

Jan 1, 1928

By Robert Thomson

"The Cobalt camp is by far the most productive camp of the Temiskaming silver-cobalt area. The date of discovery, 1903, is an important one in the history of Canadian mining; from then on prospecting and mining grew rapidly to take the prominent places they now hold in Canadian life.At Cobalt, prospectors and operators, who were to play prominent parts in other Canadian camps, received their initial training. The exploration campaigns leading to the discovery of several new camps were organized at Cobalt, and a considerable part, indeed, of the funds for these campaigns were profits from mining at Cobalt.The discovery of the Cobalt camp was purely accidental, not the result of any purposeful search. Fred LaRose, a blacksmith employed in the construction of the Temiskaming and Northern Ontario Railway, discovered mineral, afterwards determined to be valuable, within a few feet of the right-of-way. This discovery became part of the very productive LaRose mine. The publicity given this discovery, particularly by Willet G. Miller, later Provincial Geologist of Ontario, led to the rapid development of the camp.ProductionCobalt is a great camp by virtue of its silver production; cobalt is also important, although clearly subordinate. Copper, nickel, arsenic, and bismuth are by-products of mining for silver and cobalt and have not been of great importance to date.The following table gives the metal content of ores, concentrates, etc. from the Cobalt camp for the years 1904 to 1954 inclusive, as reported by the mines (l):"

Jan 1, 1949

By L. D. Boughton

Solution mining projects are conducted through one or more boreholes which penetrate en ore body. Proper drilling, completion and maintenance of the boreholes, therefore, is essential to the success of any solution mining operation. Wells drilled for solution mining encounter problems quite similar to problems encountered by the petroleum industry in drilling, completing and maintaining wells for the production of oil, gas or water. Many of the services developed and much of the experience gained by the petroleum industry is applicable to solution mining wells. As in the petroleum industry, each individual wellbore and ore body in a solution mining project provides its own problems. These vary greatly from well to well, and it is not possible to set down data or outline programs that will apply to all wells. Instead, the design of the drilling, completion, production and maintenance programs should be worked out for each individual well. The purpose of this paper, then, is to generally describe materials, equipment and techniques available for these programs and to discuss the purpose and sequence of their use.

Jan 1, 1971

By A. B. Hooker

Since man first mined underground, there has been need for adequate illumination; this need has never been fully supplied. At first, suitable lamps were not available. Gradually they have been developed, but along with that development the need for better and better lamps has continued owing to the following conditions and factors: 1. Increasing hazards from gas and dust ignitions. 2. The speeding of operations with mechanized mining, which necessitates greater visibility. 3. A demand that cleaner coal be loaded, which requires higher levels of illumination. 4. The cost of compensation for injuries that has created a demand for better illumination and safer lamps. Use of better lamps has been retarded by: 1. Prejudice and resistance to change on the part of the workers in some districts. 2. The cost and upkeep of the lamps. 3. The present types of lamps, while a great improvement over the old lamps, do not entirely fulfill the requirements for a safe and efficient light for underground workers.

Jan 1, 1938

By Ahmad Ghahremaninezhad, Rebecca Radzinski

Arsenic is a highly toxic compound that is naturally found in the environment and is released through the processing of sulphide minerals. Arsenate (As5+) is less toxic than arsenite (As3+) and is soluble in water but can form insoluble precipitates when metal ions are present. The arsenic removal processes used in industry assume that arsenic is in its pentavalent state. Hydrogen peroxide can be employed to oxidize arsenite; however, it is expensive. It has been shown that activated carbon can be used to catalyze the oxidation of arsenite with oxygen as the only consumed reagent at ambient conditions with an efficiency of 99% in less than 24 hours. The mechanism which oxidizes arsenite is not yet understood; however, this study shows that a strong oxidizing agent is formed in-situ. The species and amount of oxidant formed were determined via iodimetric titration and electrochemical methods. The production of oxidant was optimized by comparing the amount of oxidant formed in-situ to the relative amount of arsenite oxidized.

Jan 1, 2015

By H. C. Gunning

Introduction Considerable attention has of late been attracted to the area surrounding Nimpkish lake, on northern Vancouver island, by the discovery of important rich copper deposits. In less than two years some 200 mineral claims have been staked in a small area, and at least two groups have very promising surface showings. During the summer of 1929, the writer spent one month investigating the general geology and mineral deposits of the region, and, although no detailed work has as yet been done in the field or in the laboratory, the importance of the mineral discoveries and the lack of geological information available to the public warrants a preliminary paper on the district. The district is, from a mining viewpoint, very accessible. Boats from Vancouver call at Englewood, in Beaver cove, four times a week. From Englewood, a first-class logging railway, operated by the Wood, .English Company, extends to the northeast corner of Nimpkish lake. The fifteen-mile trip from the north to the south end of the lake is made by boat, two tugs being maintained by the logging company. The whole trip from Englewood can easily be made in one day. The known mineral deposits lie immediately east of the southern part of the lake, four miles or less from the shore. A fair trail, four miles ? long, leads from the lake to the Nimpkish Copper group. Apart from this trail and an old logging railway grade which follows the east side of Klaanch river for several miles, no trails exist on the southeast side of the lake.

Jan 1, 1930

By H. Y. Sohn, M. K. McCarter, Bradley C. Paul

"A computer model was constructed for bacterial leaching of the major sulfides found in porphyry deposits, including bornite, chalcocite, chalcopyrite, covellite, cubanite, enargite, native copper, pyrite, and pyrrhotite. The model incorporates equations for the sulfide minerals dispersed in the rock matrix. Leaching occurs by reactions with ferric ion diffusing into the rock fragment: Ferrous ion is resenerated to ferric with oxygen by bacteria at a temperature dependent rate. The model keeps track of the net acid generated, oxygen consumed by the bacterial oxidation of ferrous ion, heat generated, jarosite and hematite precipitated, and copper leached. The model was used to predict the rate of copper recovery, heat generation and oxygen demand for a variety of run-of-mine sized porphyry ores. These results were used in the design of a ventilation system and the economic analysis of a modified in situ extraction method that may be cost competitive with conventional copper production involving open pit mining.IntroductionA study was undertaken at the University of Utah to evaluate the technological and economic feasibility of mining copper by a method referred to as Flood Drain Leach Cell (FDLC) mining. Cells 60 by 75 meters in plan and 70 meters in height are created throughout the ore body by a modified Vertical Retreat Mining technique that includes the removal of 25% swell material. The swell material is leached in finger dumps on the surface while the cells underground are bulkheaded, flooded, drained, and artificially aerated to promote bacterial ferric sulfate leaching. Solutions are cycled through several cells to reach pregnant grade of 1 gram copper per liter of solution. These solutions are then fed to an underground solvent extraction plant and then a surface electrowinning tankhouse."

Jan 1, 1988

By Joe Wickline, Mark A. Van Dyke, Wen H. Su

"Geological factors and mine design contribute to mining-induced seismic activity, and this is especially true in longwall mining. Massive rock units are a key cause of seismic activity due to catastrophic failures that release large amounts of energy. Other factors, such as overburden depth, panel design, pillar design, rock strength, and proximity of the massive rock unit to the coal seam, all have a role in the potential and size of a seismic event. A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey (USGS) in July 2016, which had no impact on the mining operations. Further investigations by NIOSH and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia. Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity. In order to use the geology as a forecaster of mining-induced seismic events and the energy potential, two primary components are needed. The first component is a long history of recorded seismic events with accurately plotted locations. The second component is a high density of geologic data within the mining area. In this case, 181 events of 1.0ML or greater were recorded by the mine’s seismic network between January, 2009, and October, 2016. Within the mining area, 897 geophysical logs were analyzed from gas wells, 224 core holes were drilled and logged, and 1,031 fiberscope holes were examined by mine geologists. From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations. After analyzing the data, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions. Three maps were created using MineScape geological mapping software. MineScape deploys an interpolator known as FEM (finite element method) and is based on a series of gridded triangles to forecast the probability and magnitude of an event if a particular panel were to be mined. The forecast maps have shown accuracy of within 74%–89% when compared to the recorded 181 events that were 1.0 ML or greater when considering three major geological criteria of overburden thickness of 1900 feet or greater, 20 to 40 feet of sandstone within 50 feet of the Pocahontas number 3 seam, and a longwall caving height of 15 feet or less."

Jan 1, 2017

By M. Laliberte

"Gold-mine effluents are often characterized by high concentrations of copper, ammonia and cyanide derivatives (mostly cyanates and thiocyanates). While not acutely toxic to birds, this water can be acutely toxic to fishes and invertebrates. In many jurisdictions, the effluent requires further treatment in order to pass a mandatory requirement to be nonlethal to species like the rainbow trout (Oncorhynchus mykiss) or Daphnia magna. Using actual mine water, it has been demonstrated that aerated moving bed biofilm reactors will biodegrade the ammonia, cyanides, cyanates and thiocyanates, thereby removing the toxicity associated with these components. By removing copper by precipitation the water can be made to pass acute toxicity tests. Tests have demonstrated that the process is stable between 4 and 25°C, with no significant changes in the treated water composition. Once the biomass is acclimatized, the process is resistant to upsets and requires very little inputs except for phosphorus and air. Furthermore, it has been demonstrated that an anoxic reactor can be added downstream of the aerated reactors to remove nitrates if required.IntroductionThis paper will demonstrate that gold-mine effluents, which are toxic to fishes and invertebrates, can be made nontoxic by using a combination of chemical precipitation and biological oxidation.The typical composition of gold-mine effluents will first be described. The applicable legislation will then be introduced, with its requirement that the treated effluent be nontoxic. The toxicity of a typical untreated effluent will then be confirmed, and the sources of the toxicity identified. After that, a number of toxicity reduction treatment methods will be presented, and the selected method will be described.The lab tests that confirmed the efficiency of the treatment method will be presented, with three phases of testing as the understanding of the process gradually improved. Toxicity test results showing that the water is nontoxic after treatment through the temperature range will be presented."

Jan 1, 2015

By A. S. Robb

SAMPLING of an ore-body is one of the fundamentals in its exploration, development, and exploitation. It is carried out to determine the gold value per ton of an ore-shoot and the probable gold output of the refinery. Sampling also places any broken ground in one of two classes, ore or waste. The value and importance of correct sampling has been shown repeatedly in the past. On the other hand, instances could be given where those in charge of mines have not believed in sampling, and the result has been the same in every case-disaster. This has in all probability been due to assuming that good-looking, well-mineralized rock was ore. Sampling in some form might have averted this misfortune. In this essay, only the method of sampling and the estimation of ore reserves is treated. All titles, figures, and values are fictitious. None of the illustrations can be directly applied to any portion of the Hollinger mine, except Figures 1 and 2, which are included with the special permission of the Canadian Mining Journal. METHODS OF SAMPLING Hollinger Consolidated Gold Mines, Limited, has, from the very beginning of operations, carried out an extensive system of sampling, and the results of this sampling have completely governed the whole mining programme. The Hollinger discovery was made in 1909 and prospecting and exploration of 'the surface began at once. Four men were given jobs as samplers and they sampled thoroughly all the outcrops and all bed-rock which could be exposed to view by removing the overburden. When shaft sinking began, samples were taken at two-foot intervals. In 1912, an underground gang of six samplers was organized, and the number was increased at a rate of about two men per year as the size and extent of the workings grew. No permanent record of sampling was kept until 1919, in which year an average of 11.6 men took 28,458 samples, cutting 113,894 feet of sample. From that time until the end of 1934, the average number of samplers varied, but the total number of samples cut, and the total footage sampled, increased.

Jan 1, 1937

By P J. Handley

"Predicting how coal seams will be beneficiated through the coal handling processing plant (CHPP) has long been challenging within BHP Coal. Various coal seams from different areas are mined and stockpiled separately, often depending upon a deleterious coal quality parameter; high/low trace elements for example. These stockpiles are then fed in different ratios into the CHPP to produce the desired product/s. In understanding the washability characteristics of the feed source, mine geologists and process engineers work together to improve the beneficiation of different coal materials through the CHPP.For the majority of the BHP Coal deposits, the washability data is available for the coal seams across the deposits. However, no previous standardised modelling and prediction technique existed that could ensure the correct information was available for forecasting and refining CHPP processes. This paper will discuss the steps undertaken to implement a geometallurgical prediction tool that simplified and streamlined the washability modelling and yield estimation process. The value realised to the BHP Coal assets resulting from this process was: improved compliance to plan increased throughput increased CHPP recovery through improved efficiencies and increased revenues.CITATION:Handley, P J, 2017. Washability modelling and estimation techniques used to improve coal handling preparation plant beneficiation, in Proceedings Tenth International Mining Geology Conference 2017, pp 327–336 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017