Search Documents

By Henrik Saxén, Mikko Helle

The operation of hot stoves used for preheating the blast in the ironmaking blast furnace has a strong effect on the consumption of reductants, economic performance of and CO2 emissions from the steelmaking site. Generally, it is recommended to maintain as high blast temperature as possible, because this minimizes the rate of reductants in the blast furnace. The blast temperature is affected in a complex way by the time periods of heating and cooling of the stoves, and by the amount of gas combusted in the stoves. Furthermore, as the hot stoves show degraded performance with age, it is a non-trivial task to select optimal operation parameters for the stoves. The paper addresses this computationally by applying a one-dimensional heat-transfer model of the hot stoves for optimization of the performance of the system. The complexity and strong coupling of the decision variables is demonstrated by numerical examples, where the blast temperature is maximized under different constraints.

Jan 1, 2015

By John Owens, Hamid Maleki

Efficient and safe use of mobile roof supports (MRS) depends on the interaction between the MRS and coal strata. Of particular interest to this study are the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods, and MRS load-bearing capabilities. To provide a better understanding of the mechanics of strata deformation, the authors have collected and reviewed measurements of convergence and stress in one western U.S. mine and have completed pseudo-three-dimensional, boundary-element modeling for two typical pillar-pulling plans. Stress distribution in the mine roof above pairs of MRS’s was calculated to demonstrate how MRS’s contributed to the control of roof block movements. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal-measure rocks and by pillar-pulling sequences and layouts. MRS’s and other support systems play a critical role in controlling the stability of both the immediate roof and the middle roof for a distance of up to 18 m (60ft) above the seam. MRS’s provide unique ground control advantages over other types of secondary support by significantly reducing the time between mining and installation of secondary support. Although MRS’s are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at near-peak capacity, whereas posts fail and loose their ability to limit mine roof deformation.

By Robert Agar

This paper reviews the mineral exploration applications of satellite and airborne multi- and hyperspectral data and field spectrometers, and attempts to provide a setting in which each might be best applied.

Apr 24, 2001

"With a total value to date of well over $200,000,000.00 for its ore production, the Tintic mining district, which is about 100 miles southwest of Salt Lake City, ranks as one of the three main ore producing areas of Utah. In it are located the biggest silver mines of the country, silver having been the chief metal produced in the camp since its start. Tintic's silver production to date has a total value of over $ 100,000,000, approximately half of the value of the camp's ore production, the balance being roughly divided among lead, gold and copper.Discovery of the camp was made in the late sixties. Lack of transportation and ore reduction facilities delayed extensive development of the area for nearly a decade.In recent years Tintic's ore production has ranged from 350,000 to 400,000 tons annually. In 1 924 the camp produced one-eighth of the silver produced in the nation with an output of 7,729,700 ounces. Its lead production was 77,765,000 pounds and its gold production 26,285 ounces.The known mineralized area of the district is found in a broad syncline striking north and south. The west limb plunges sharply and extends for a distance on its dip of approximately one and a half miles to the trough. The east limb raises gently through a distance of about two miles to the east limit of known mineralization. This general structure is broken by local faulting throughout the district, the local structural conditions playing an important part in the ore deposition. The north end of the fold is obscured by a rhyolite flow and the south end stops against a monzonite stock."

Jan 1, 1925

By Edwin B. Wilson, Charles F. Cockrell

The application of evolutionary operation is proposed for the cleaning of coal by the heavy media process. Analysis of the data given suggests some benefits that may not be immediately appreciated unless evolutionary operation is applied. For example, while it may seem obvious to increase specific gravity when the ash and sulfur content of the clean coal is lower than that allowed, evolutionary operation may show that an increase in feed rate or an increase in both feed rate and specific gravity would be a more profitable alternative. In addition, by using evolutionary operation, up-to-date knowledge of the effect of change of feed rate or specific gravity on yield and product quality is available. This information facilitates confidence about decisions made in regard to the day-to-day operation of these units. A number of other applications in the minerals industry are proposed. An application of evolutionary operation in a related field is also given where a large number of variables were required to be optimized.

Jan 1, 1969

By S. P. Holt

The Salt Chuck mine is on the east bank of the Salt Chuck, a salt-water inlet at the head of Kasaan Bay, Prince Edward Island, Southeestern Alaska. The deposit was worked at intervals from 1905 until. 1941. Early ship-ments of hand-sorted ore are reported to have assayed about 4 percent copper, 0.15 ounce gold, and 0.15 ounce silver. The total mine production up to 1941 is reported to have been 326,000 tons containing 6,200,000 pounds of copper. During December 1942 the Bureau of Mines cut a 15-foot channel sample on the surface and channel samples from headings on the 300-foot level. In July 1943 a development project was started. Thirteen diamond-drill holes totaling 1,550 linear feet were drilled from underground stations on the 200- foot and 300-foot levels.

Jan 1, 1948

By Jr. Koch

In the Hydrogeochemical and Stream Sediment Reconnaissance (HSSR) phase of its National Uranium Resource Evaluation (NURE) pro¬gram, the U.S. Department of Energy (DOE) samples about 1400 sites for stream sediments in each two-degree quadrangle of the National Topographic Nap Series (NTMS) and about 1200 sites for ground or stream water. Through a geological/statistical analysis, we find that NURE data are useful for assessing the uranium resources of the NTMS quadrangles. Our computer-implemented System for Uranium Resource Evaluation (SURE) calculates a score for each NTMS quadrangle based on the HSSR, geologic, and radiometric data; we score the four Colorado quadrangles--Pueblo, Montrose, Durango, and Trinidad--that comprise the study area. We interpret the scores in terms of geology and the known occurrences, which include the Hanson ore deposit with reserves of 30,000,000 lbs. U308 and the Pitch mine with reserves of 1,740,000 lbs. SURE depends in part on distinguishing mineralized or metalliferous granitoids from barren ones through "geochemical signatures."

Jan 1, 1980

By J. Budac, R. Kofluk, D. Belton, M. Sjogren

A series of tests were performed to determine the flammability limits of mixtures of oxygen, ammonia, steam and nitrogen, over a solution, in a sealed autoclave. The partial pressures of ammonia and oxygen in the vapour space were varied by adjusting the character of the solution and by adjusting the oxygen concentration in the oxidant gas respectively. The data shows that flammable conditions can be minimized by controlling the operating temperature, reducing the ammonia content in the solution, increasing the concentrations of Ni, Cu and Zn in solution and keeping the % oxygen in the gas phase less than 15.5. Observations were also made that suggest that the presence of an aerosol in the vapour space may hinder ignition.

Jan 1, 2004

The Operation of the LAROX PF-50 Pressure Filter at 'Ellatzite-Med' Flotation Plant, Bulgaria The implementation of Larox pressure belt filter, type Larox PF-50 provided within 6˜8% moisture content of the produced copper concentrate, which allowed good market realisation. The start-up of the pressure filter in 2009 reduced the electricity costs several times and had a positive impact on the technological regime of flotation. This article reveals the investigation results from the operation of the pressure filter according to different situations (density of the pulp, time for filtration, pressure of the material, pressure of the drying air, time for drying with air and other factors). The investment made in the pressure filter application is a guarantee for the successful operation of 'Ellatzite' flotation plant, Bulgaria in the coming years.

Sep 13, 2010

By T. Fraser, F. F. Giese, R. L. Sutherland

Under a cooperative agreement between United States Bureau of Mines and the Truax-Traer Coal Company, some operating-scale experiments have been made with the cyclone thickener in the preparation plant of the Shamrock No. 1 mine at Kayford, West Virginia. These tests were made with a 14-in. cyclone of the type developed by the Dutch State Mines in Limburg. It was applied experimentally to the thickening of solids in washery water to obtain performance data to show the range of sizes that may be recovered and other operating characteristics that would indicate the field of usefulness of this device in coal preparation practice. This is a progress report only. It covers results obtained in a series of 17 tests of the operation of what has been considered a unit of commercial size operating on suspensions of fine coal mixed with a relatively small amount of free impurities. The underflow material, after further dewatering in centrifuges, is a marketable grade of coal. The coal at Shamrock No. 1 is mined from the No. 2 Gas seam. It is made up essentially of a low ash coal suitable for byproduct use with one or more bands of splint coal of higher ash content suitable for industrial fuel. The washing plant was installed for the two-fold purpose of removing the free impurities incident to mechanized mining and to separate the run of mine coal into the two types. To accomplish these results it is necessary to make a separation at a specific gravity of about 1.4 to recover the byproduct coal and to separate the splint coal from refuse at a higher gravity. The coarse coal section of the washing plant was put into service about 10 months before the fine coal section was completed. Inadequate screening capacity in the raw coal preparation plant resulted in a portion of the fine coal being fed to the jigs. No provision for preliminary dedusting of the raw coal feed was incorporated in the design. Under the conditions in the initial operating period, separation at the desired lower gravity was not realized, apparently because of the presence of an excessive amount of fine solids in suspension in the wash water. Difficulty in wetting the fine coal may also have been a contributing factor. Additional facilities for the removal of the fine solids from the wash water was indicated. Information then available on the Driessen cone for this purpose was studied and a cooperative agreement with the Bureau of Mines for experimental work with a unit of standard size as developed by the Dutch State Mines was arranged. During the time required for construction of the cone it was found the addition of a small amount of wetting

Jan 1, 1950

By J. B. Carman

This paper, describing the mining practices and methods at the mine of the Molyb¬denum Corporation of America, is one of a series of similar papers on mining methods in the various mines of the United States being prepared by the Bureau of Mines. The mine of the Molybdenum Corporation of America is in the Red River mining dis¬trict, Taos County, northern New Mexico (fig. 1), The mill and camp are in the valley of Red River, about 7 miles east of the town of Questa; the mine is 1 ¼ miles away, in Sulphur Gulch, a tributary of Red River. The mine is about 600 feet higher than the mill, at an altitude of about 8,700 feet. The climate is cold in winter, but does not interfere serious¬ly with continuous operation. The mine normally produces about 40 tons of sulphide molybde¬num ore per day, which is concentrated at the local mill and chipped to the plant of the Molybdenum Corporation at Washington, Pa.; there it is made into either ferromelybdenum or "molyte" (calcium molybdate), for use in alloys. The ore is mined from narrow, irregular veins by the cut-and-fill method. About 65 men are normally employed underground and on the surface at the mine.

Jan 1, 1931

By R. W. Huber

Three arc-melted ingots, two of a titanium-7 percent manganese alloy and the third of unalloyed titanium, were forged and rolled into 3/4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties. These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots. INTRODUCTION Arc-melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Park, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.

Jan 1, 1955

By R. O. Pynnonen

This circular is a study by the Bureau of Mines of 346 accidents in underground iron-ore mines of the Lake Superior district from June 1949 to August 1954. These accidents caused 354 lost-time injuries, including 28 fatalities and 2 permanent-total disabilities. The accident reports were analyzed by the Bureau to show the causes of injuries and the time charges and unsafe practices or conditions that caused the accidents. Also shown are the times of occurrence, ages of the injured by job classification, and experience of the injured in mines and on the job being performed when hurt. Detailed information is presented on approximately 14 percent of the total number of Lake Superior district underground mine accidents that resulted in lost-time injuries during the period covered. These facts are presented to aid accident-prevention measures in underground mines and as a record for measuring future safety accomplishments.

Jan 1, 1956

By Mark Freberg

"IntroductionThis chapter is intended to provide information on the operation and maintenance of several pieces of equipment used in heavy media separation. Most heavy media separation circuits, particularly those involving bath separators can be considered as high maintenance areas. Because of this the efficient operation and maintenance of these circuits is very important if the cost per ton of material treated is to be kept to an acceptable level.Heavy media separation (HMS), is a process used to separate particles of different specific gravities. Under laboratory conditions the ideal way to separate two types of particles which have different specific gravities is to suspend them in a heavy liquid which has a specific gravity between those of the two types of particles. Those particles with the lower specific gravities will float on top of the liquid while the higher specific gravity material will sink to the bottom. Given enough time and a sufficient volume of heavy liquid this process will be essentially insensitive to the sizes of the particles involved.Heavy media separation circuits make use of the same principles described above. The material to be treated is introduced into a mixture of finely ground solids, called media, and water which takes the place of the heavy liquid; the mixture of solids and water is known as medium. The separating force can be either gravity or centrifugal force. The type of solids used as media varies but it is usually a high specific gravity material such as magnetite, galena or ferrosilicon.Heavy media separation is used extensively in the cleaning of coal and to a lesser extent as a preconcentration step in base metal and iron ore operations."

Jan 1, 1989

If you are to be and remain competitive in the mining industry, it is vital that your company management systems are efficient. An integral part of today's competition in a ruthless market is to keep internal costs to a minimum. Integrating our core and parallel management systems is becoming an essential strategy to ensure efficiencies are maintained to the highest level, allowing the maximisation of profits, and to maintain that leadership status within our industry. The uniquely designed Integrated Management Process provides the path to develop, implement, and monitor an Integrated Management System in a simple but highly efficient and effective manner.

Jan 1, 1997

By J. Riss, S. Gentier, A. Marache

The study of the hydromechanical behaviour of fractured rock masses requires a detailed knowledge of the isolated fractures. The aim of the paper is the simulation of the evolution of the void space, located between both walls of a fracture, during a shear test under constant normal stress. Results of the mechanical simulation model are first validated then analyzed in detail. We observe that, during the shear process, there is an opening of the fracture with the creation of preferential channels. These channels are determined at the early phase of the shear process (pre-peak phase), and we observe during the post-peak phase that void areas increase in size rather than the creation of new apertures. Die Untersuchung des hydromechanischen Verhaltens eines zerlegten Felsmassivs erfordert genaue Kenntnisse der einzelnen Spalten. Ziel dieses Artikels ist die Simulation der Evolution des Hohlraumes zwischen den beiden Wänden eines Spaltes während eines Abscherungsexperimentes unter konstantem senkrechtem Druck. Die Ergebnisse der Modellierung werden zunächst mit dem Abscherungsexperiment verglichen und dann im Einzelnen ausführlich analysiert. Während des Abscherungsprozesses tritt eine Öffnung des Spaltes auf, die die Bildung von bevorzugten Fliesswegen fördert. Diese Kanäle werden bereits in einer frühen Phase des Abscherungsprozesses (pre-peak Phase) festgelegt. In der post-peak Phase tritt dann eher eine Vergrößerung dieser Kanäle, als die Bildung neuer Hohlräume auf. L’étude du comportement hydromécanique d’un massif rocheux fracturé ne peut se faire sans une connaissance approfondie des fractures le constituant. L’étude présentée dans cet article concerne la simulation de l’évolution de l’espace des vides présent entre les deux épontes d’une fracture au cours d’un essai de cisaillement à contrainte normale constante. Les résultats du modèle sont tout d’abord validés puis analysés en détail. On constate que, au cours du cisaillement, il apparaît une ouverture de la fracture permettant la création de chenaux préférentiels. Ces derniers sont déterminés très tôt dans le cisaillement (phase pré-pic), et on observe dans la phase post-pic davantage un accroissement de la taille des chenaux plutôt que la formation de nouvelles zones de vides.

Jan 1, 2003

By J. L. Nebreda, Z. Fan, J. B. Patel

"A380 alloy has been widely employed to produce thin-wall components via high pressure die casting (HPDC). During HPDC processing, there is a significant problem of property variation even with the very stable and precision automated casting procedure. The enlarged variation lowers the component performance and affects the steady and uniform property distribution along the whole component. In this study, high shear melt conditioning technology was developed and applied to the melt prior to pouring into the shot sleeve. Experimental results show that with application of intensive melt shearing, the variation of elongation was decreased from 21.8to 13.9%, and yield strength variation was reduced from5.5to 3.6%. The improved property variation is attributed to enhanced nucleation both in shot sleeve and the die-cavity, and to the improved distribution of porosity and secondary phases as a benefit of high shear induced grain refinement. With application of high shear, large number of the Spinel phase (MgAl2O4) particles with double size distribution in average diameter of 80and 300nm were formed. Due to the good orientation relationship and small misfit between alpha Al and MgAl2O4, the particles act as the effective nuclei in shot sleeve and die cavity, respectively.INTRODUCTIONA380 alloy had been widely used for produce automotive components by cold chamber high pressure die casting(HPDC) processing, due to its relative good mechanical properties and cast ability performance, and more important most of A380 ingots were produced by recycled Al alloys. Therefore, to promote utility of A380 will contribute to reducing emission of CO2and to the lightweight of automotive industry as well. When cold chamber HPDC was employed to produce the components, the mechanical properties of A380 alloy always have a distribution range (named variation herein), or in other words the properties were not stable. The reason was ascribed to the typical solidification characteristics occurred in HPDC processing. During HPDC processing, there are three steps of melt movement. The first step is that the melt was poured into shot sleeve at temperature of about 680°C, in which shot sleeve was preheated by few shots of melt filling, or by heater. During step one, the first solidification of melt was happened in shot sleeve and about 20% solid made of coarse a-Al grains was formed(Li, Xiong, & Guo, 2016).Such kind of grains will retain in the final products and deteriorate the properties variation. The second step is that the melt was forced moving forward slowly by plunger at about 0.2–0.3m/s until the liquid melt front to the inner gate of mold. The third step is that the melt moved very fast to complete the filling of die cavity and refilling the solidification shrinkage by fast movement of plunger about 2–3m/s. The second solidification was occurred in die cavity and fine a-Al grains will be formed by high cooling rate at about 500–1000°C/s. From the solidification point of view, the grain size was dominated by nucleation and growth. When HPDC was employed to produce components, the melt quality becomes the priority factor to control the solidification process as the other casting parameters were kept at the same."

Jan 1, 2018

Rope guides, consisting of ropes spanning between anchor points at the top and bottom of shafts, have frequently been considered as a viable alternative to fixed guides, comprising buntons and guides. However, their design has generally been based on empirically derived rules, arising from European hoisting practice of 50 to 100 years ago. This paper describes a recent technology development project aimed at defining and quantifying the important forces acting on rope guided conveyances, calculating the resulting displacement of the conveyances and assessing whether the displacements are acceptable or not. The paper describes the derivation of aerodynamic force coefficients based on CFD analyses and other significant forces acting on the conveyance and rope system. The conveyance displacements may be calculated using computer simulation of the mechanical system, or approximately using simplified equations given in the paper. Measurements taken to confirm the suitability of the proposed formulation are described. The combination of displacements and assessment of the rope guide system design are proposed, based on the ratio of design clearances and the predicted displacements.

Jan 1, 2005

By Norman A. Grant

"Location and Transportation FacilitiesTHE BEAVERLODGE area of North Saskatchewan is on the north side of lake Athabasca, 500 air miles northeast of Edmonton.The main Eldorado operation and townsite are on the north •side of Beaverlodge lake, which is immediately north of lake Athabasca and is separated from it by only a mile long portage at Lodge bay. The once famous town of Goldfields. Saskatchewan, and the Box property of the Consolidated Mining and Smelting Company of Canada, Limited, are located on lake Athabasca nine mines from Beaverlodge townsite.Previously, all Eldorado freight was delivered by barge at the Lodge Bay portage, hauled across the portage, and across Beaverlodge lake by small Northern Transportation Company barges, which involved many handlings.In 1952 the port of 'Bushell' was established at Black bay. This is a particularly snug harbour, well protected from the main body of the lake and with good foundations for docking facilities. A Butler building, 300 ft. by 60 ft., and tank farms provide storage at the port. A •road from Bushell to the main Beaverlodge operation, a distance of twelve miles through rugged terrain, was built by the Saskatchewan Government. The cost was shared by the Saskatchewan Government, the Federal Government, and Eldorado and other mining companies.Along this road are located the properties of several enterprising mining companies and near the midpoint lies the ambitious budding town of Uranium. This road has made portaging unnecessary and palletized freight loaded at Waterways, Alta., is now loaded directly on trucks at Bushell and delivered to the point of consumption."

Jan 1, 1953

By P. H. Dudley

When we see the magnificent passenger-trains of from 8 to 12 coaches, drawn by locomotives weighing from 100 to 110 tons, at speeds of from 50 to 60 miles per hour between terminals, to make a schedule of 45 miles per hour, and freighttrains of from 50 to 75 cars of 60,000 pounds capacity, drawn by one locomotive, it is hard to realize that it lacks a few months of fifteen years since my pioneer 5-inch 80-pound rail for the United States was laid by the New York Central aid Hudson River Railroad Co., in July, 1884, on the Harlem line. Shorter passenger-trains, of from 4 to 5 coaches, are run much faster, notably the Empire State Express, the schedule of which for the 440 miles between New York and Buffalo requires 53.3 miles per hour, calling for a running-speed, for much of the time, of from 65 to 75 miles per hour, while higher speeds are very common. On other railroads laid with my 5 1/8-inch 80-pound rail, speeds of from 60 to 75 miles per hour obtain in daily practice. On many of the important railroads east of the Mississippi high speeds of from 60 to 70 miles per hour are part of the daily service. So many instances of speeds of 90, and even 100, miles per hour have been recorded that they must be considered as likely to occur on important lines, and provision must be made for them in the track. Solid mail-trains of from 6 to 8 cars are run from New York to Chicago, 1000 miles, in twenty-four hours; and, commeneing with the present year, shorter trains are running from Chicago to San Francisco, 2000 miles, in three and one-half days. In the freight-service equally important progress has been

Jan 1, 1900