Search Documents

By Robert G. Bottge

The Bureau of Mines investigated the availability of the land in south-central Alaska for exploration and mineral development of locatable minerals under State or Federal laws. The land ownership for an area of nearly 72.5 million acres in south-central Alaska was divided into 3 availability categories and 15 subcategories. In July 1985, 31.0 million acres of the study area were available for mineral exploration and development, 6.2 million acres were available with restrictions, and 35.3 million acres were unavailable. About 23.6 million acres in the study area are underlain by mineral terranes. About 9.9 million of the 23.6 million acres are available for mineral entry, 2.4 million acres are available with restrictions, and 11.3 million acres are unavailable. While much of the land currently classified as unavailable will be reclassified once it is conveyed to the State or to Native corporations, about 22% of the unavailable lands underlain by mineral terranes are now Federal parks, preserves, wildlife refuges, wild and scenic rivers, and military lands, all of which are considered permanently unavailable for mineral exploration and development.

Jan 1, 1986

By C. Pichler, C. Benigni, J. Antrekowitsch

"The recycling of steel mill dust results in zinc oxides which are sold to the primary industry in or-der to recover zinc in its metallic form. Due to the contained impurities - chlorine and fluorine - these sec-ondary oxides are usually charged into the roaster together with primary concentrates. Appearing problems in this furnace limit the application of secondary materials. Based on the zinc amount, a direct leaching, assumed that a low halide concentration is present, would be possible. To use the zinc solution directly in the electrowinning stage, the concentration of impurities, first of all iron, is limited. Iron can be found in secondary zinc oxides due to carry over during the recycling process. In order to reduce the iron content in the solution, the leaching has to be pH-controlled. This leads to a limited number of simple purification steps before the solution enters the electrolysis. Various trials were performed to evaluate the influence of temperature, time and sulphuric acid concentration on the iron dissolution. This paper deals with the results and also focuses on other impurities such as halides. Additionally, the soda washing process, usually done with secondary zinc oxides to remove most of the halides, and the challenges within this step are discussed.INTRODUCTION Recycling of steel mill dust, which is the main zinc containing residue, in the Waelz process dis-plays the common method worldwide. The product of the process is a secondary zinc oxide which is con-taminated with different elements like lead, iron and halides due to mechanical carry over or evaporation. Depending on the feeding material the concentration of each element in the dust is varying. The zinc con-tent of the product, also called Waelz oxide, lies around 65–68%. Based on these values it presents an al-ternative to the primary concentrate for the production of metallic zinc. The contained halides limit the direct utilization in the leaching stage and therefore have to be reduced. State of the art is a soda washing process but also solvent extraction gives a possibility to remove chlorine and fluorine but the desired con-centration for the electrolysis is hardly reachable (Antrekowitsch et al., 2016) Iron is present as an undesirable component of such secondary zinc oxides due to carry over. During the hot acidic leaching of the secondary concentrate, iron is dissolved too. Based on the higher electrical potential iron has to be removed before the zinc solution enters the electrowinning stage. It is usually removed by precipitation as goethite, hematite or jarosite, which is the common precipitation residue (Ismael et al., 2003)."

Jan 1, 2017

By R Stead

So many ceramics look the same, but are they?In the past 20 years, there have been significant changes in the materials available, as well as changes to the supply chain, for ceramics used in wear applications in the hard rock mining industry. The biggest change in supply has been from the Chinese market, with many suppliers promoting their products as æstate of the artÆ. Some of them are state of the art, but are they all? There will be some concluding remarks in this respect.There are still some outstanding new developments coming from the more traditional suppliers and these should not be ignored. However, as an end user, how can one be sure that the product received meets the technical specifications of that material?This paper will address some of the questions on how to differentiate between different materials by giving a technical overview of the current (but not exclusive) range of popular ceramics, plus incorporating how these ceramics are used in process plant products by presenting case studies. The presentation will include technical data coupled with micrographs of various ceramics to illustrate just why they are different.It will also be shown that by careful selection of the wear material, it is possible to gain significant benefit when using superior materials in an ore processing plant. The impact of cost of the products, life, process efficiency, and reduced maintenance costs will be considered using cyclone components as an example.The properties (including the microstructures) of the various ceramics will be compared to the application in order to get some understanding of what is considered good or bad.Misra and Finnie (1982) summarised their paper, æA review of Abrasive Wear of MetalsÆ by saying:à it is difficult to give guidelines for selecting materials for abrasive wear resistance. Each application is a different one, and a design engineer has to take into account various other factors such as impact, fatigue and corrosion which are often coupled with abrasive wear. The same applies to ceramics.CITATION:Stead, R, 2013. Applications of ceramic wear materials in the gold industry, in Proceedings World Gold 2013, pp 325-330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Peter R. Sanford

Cyanides are present as a dilute constituent of streams from a variety of metallurgical and mineral-processing operations. In addition, a cyanide concentration in excess of approximately 100ppb is toxic to aquatic life, and consequently these operations require a waste-treatment process to reduce the already dilute cyanide species by several orders of magnitude. Furthermore, the waste streams may have flowrates in excess of a million gallons per day. The paper reports on research conducted with a laboratory?scale electrochemical porous (graphite felt) electrode (anode) flow-reactor, which was conducted in conjunction with a computer-aided simulation of a mathematical model describing the intrinsic rate-phenomena associate with the electrode processes. The laboratory-scale cell, of rectilinear geometry, was found to be capable of reducing a feed-stream anolyte (KCN-KOH and supporting electrolyte of a single salt ? K2SO4) with a cyanide concentration of 10ppm, to less than 100ppb, at current efficiencies in the neighborhood of 50%. The computer simulation of the cell performance based on the mathematical model (and constraints imposed for tractability) was found to provide only for qualitative agreement.

Jan 1, 1998

By A Hekmat, R Castro, A Casali, R Gómez

Block caving is the most economic underground methods for excavating massive orebodies, due to the high productivity and low production costs. The success of block caving operations depends on the fragmentation and draw control as large blocks decrease the equipment efficiency, inhibit the material flow and may lead to expensive secondary blasting. Even though ore handling system design, as well as overall economic results, both critically rely on secondary fragmentation, this parameter continues to be one of the least understood issues in the caving operations.This research focuses on the experimental study of secondary fragmentation, considering the impact of vertical pressures and material flow. Experiments using a load-haul-dump extraction system were conducted under laboratory conditions to quantify the influence of pressure and particle size on secondary fragmentation. Results demonstrate that increasing the vertical pressure (simulating deeper conditions) leads to higher fragmentation (smaller particle size) and greater fines generation during draw. The experimental results were applied to calibrate the developed mathematical model based on kinetic matrix. The acceptable accordance between the comminution model results and the reality showed that this method is convenient in predicting the secondary fragmentation in block caving.CITATION:Castro, R, Gómez, R, Casali, A and Hekmat, A, 2016. Experimental and comminution model framework for secondary fragmentation prediction in block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 175–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Donald Leroux, Dave Scott, Giovanni Di Prisco

"The Lady Loretta lead-zinc deposit in Northwest Queensland, Australia contains an average of 5.9% lead, 17.1% zinc and 97 g/t silver. Ore mineralization is mostly comprised of fairly complex intergrowths of pyrite, sphalerite and galena. Starting in 1998, Noranda Inc., the major joint venture partner of the project, conducted extensive metallurgical test work, which culminated in July - August 2000 in a series of Pilot Plant tests. A common thread to all the metallurgical work has been the deportment of a large portion of silver into non-payable metallurgical products. Average silver distribution from four Pilot Plants shows a distribution of silver in lead concentrate of 28%, whereas silver in zinc concentrate was 49%, and 23% in the final tails.The consistently poor silver recovery as well as the fairly unusual silver distribution, particularly in zinc concentrate, was considered an issue to be thoroughly investigated. A mineralogical plan was devised to determine if these particular metallurgical results were somewhat related to the nature and mode of occurrence of silver carriers. Work was performed to determine discrete silver-bearing minerals and/or silver contained in solid solution in a suite of commonly occurring sulphides. Ore microscopy, SEM methods, Electron Microprobe and Ion Microprobe analyses were all used to answer these questions, and to find the silver carriers, so a metallurgical plan could be devised to improve silver recovery.INTRODUCTIONPotential economic exploitation of the Lady Loretta deposit in Queensland, Australia is driven by revenue derived from zinc and lead flotation concentrates and co-product silver recovery in lead. Relatively low recoveries of payable silver to lead concentrate, and high silver distribution to zinc concentrate necessitated an investigation into the natu"

Jan 1, 2002

By Robert F. Chaiken

An absorption-desorption model of particle reactivity was employed to describe the observed relationship between two apparently diverse phenomena which have been the subject of considerable study at the U.S. Bureau of Mines: (1) coal-rock dust reflectance and (2) coal-rock dust explosibility. The model accounts for heterogeneities in particle-size and material properties; however, in the present report, only particle-size distribution is considered. A mean particle-size parameter, appropriate to the explosion extinction process, is derived, and then taken as appropriate to describing optical reflectance. The derived form-to-function relationships for the two processes, when compared with experimental data, suggest that a problem exists with previously derived theory relating optical reflectance to rock dust concentration. A reexamination of that theory leads to a new theoretical expression, changed by a factor of 2, for the variation of rock dust concentration with reflectance which is in quite good agreement with experimental results. The current work offers justification for measuring and establishing rock dust requirements for specific coal dust size distribution(s) found in the mine-distributions that undoubtedly depend on the mining method and the type of coalbed.

Jan 1, 2010

By AIME AIME

THE second session on geophysical prospecting at the February meeting of the Institute was a discussion of the mining law and the bearing of the new method of search on location of claims and assessment work thereon. Allen H. Rogers was chairman of the meeting, which he opened by reviewing the present law and the proposed changes. W. R. Ingalls commented (by letter) on the Arentz bill, as introduced into the House of Representatives in 1921 and the need for revision of the present mining law. L. W. Douglas explained (by letter) the bill that he introduced and which has been passed by the House. SAMUEL S. ARENTZ, Nevada: It is my opinion that if the American Institute of Mining and Metallurgical Engineers is to sell this proposition to the people in the West, they have to sell it to the lawyers, because, after all, they are heard loudly when it comes to speaking in Congress. One man tells the other, "This thing is a vicious piece of legislation"; it might not be, but they will pass it on if it affects them. If the Institute would impress on the people affected that we need a re-codification of the mining law and that such is necessary along certain lines; that things have changed during the past decade or two, so today instead of doing our prospecting alone through the sinking of a shaft, through a discovery that may be seen, we are now moving on to more modern means of discovery through geophysics, through the churn-drill, through geology, through geological inference, I think we could get somewhere.

Jan 1, 1929

Agenda ? Introduction ? Inmet?s Operations and Closed Properties ? Inmet?s SECA Philosophy ? Inmet?s SECA Framework ? The Business Case for TSM ? Inmet?s TSM Reporting ? Inmet?s 2004 TSM Performance ? Opportunities for Improvement ? What Have We Learned From The TSM Process So Far? ? Summary Introduction ? Inmet has evolved into a strong TSM supporter ? Inmet is confident that TSM can be successfully and cost effectively implemented by smaller companies ? Inmet?s reporting on economic, environmental and social performance was raised significantly in our 2003 Annual Report ? a signal our commitment to good performance and improvement in these areas ? Our 2004 Annual Report has been further enhanced with the inclusion of our TSM performance

Apr 1, 2005

By S. K. Kawatra, S. J. Ripke

Bentonite clay is used as a binder for iron ore concentrate pelletization. Bentonites are sensitive to cations such as calcium, magnesium, sodium, and potassium that are known to be dissolved in the moisture remaining in the iron ore concentrate. These cations affect the ability of bentonite to absorb water, as measured by the plate water absorbance (PWA) test. This paper addresses the relationships between plant water chemistry and pellet strength for a wide PWA range of bentonites. Experiments were conducted to determine the effect of concentrate moisture solute chemistry and bentonite PWA value on the wet knock and wet and dry compressive strengths of iron ore pellets. Experiments used seven different types of bentonite that had PWA values ranging from 564 to 1033. Flushing plant concentrate with distilled water to remove the dissolved cations resulted in increased pellet strengths, to a widely varying degree, for each bentonite tested; wet knock values increased an average of 92% and dry compressive strength increased an average of 46%. In addition, pellet strengths were not found to be directly related to the ability of bentonite to absorb distilled water, measured by the PWA test.

Jan 1, 2002

By Frank C. Appleyard

As the environmental movement gained force during the past few years, it was inevitable that attention would be focused on surface mining, and we have seen this method of extracting minerals from the ground come under heavy attack by conservation groups, the press and television, legislators at all levels of government,, and the public at large. It is difficult, and in some situations, perhaps impossible, to measure either the need for, or the results of, land reclamation in absolute terms. Therefore, much of the criticism of surface mining has been based upon subjective analysis rather than hard data, with the result that discussion of the subject often includes a fair amount of emotional response. To be fair, this reaction is not limited to just our critics; even we hard headed engineers sometimes respond in the same way, an observation with which you may agree when I finish this talk. This leads to the thought that whether you are for it, or against it, land reclamation in many respects is a state of mind. That is, our reaction to it can vary considerably, depending on how far we have thought it through. And think it through we must, because the pressures being brought to bear need to be met with positive actions if the problem is to be brought under control, and in the next few minutes I would like to discuss from a management point of view some ideas which might aid in this thinking process. It would be a mistake, I believe, to think that the current energy crisis will suddenly bring the environmental movement to a stop, and therefore, we can relax and go back to running our busi¬ness the way we used to. This is not realistic; on the contrary the energy crisis is focusing attention on the limitations of our natural resources as nothing else could, and with respect to land

Jan 1, 1974

By T. M. Sukel

Engelhard Corporation is one of the leading producers of kaolin based products in the world, having acquired the assets of Freeport Kaolin company in 1985. Much of the production technology used in the kaolin industry was pioneered by Engelhard and Freeport, including Ultraflotation for improving product brightness, delamination to produce kaolin platelet products, calcination to produce ANSILEX® high opacity titanium dioxide pigment extender and pipeline slurry operations to economically transport kaolin from the mine to beneficiation facilities. Engelhard traces its roots back to 1870 when the Edgar family discovered kaolin behind their property in Bonhamtown, New Jersey. Today the company produces the broadest line of premium coating pigments with extensive sales throughout the world. The international scope of the company's business has led Engelhard to evaluate kaolin deposits throughout the world as possible grass roots production sites. Most kaolin products are used in the paper industry -- the largest volume end-user 80% of the total market -- as filler and coating pigments. Lower volume specialized applications include fillers and reinforcements for plastics and TiO2 extender pigments for paints and coatings.

Jan 1, 1987

By Mark Van Dyke, Gamal Rashed, Khaled Mohamed, Timothy Barton, Morgan Sears

"The unconfined compressive strength (UCS) of coal is an important parameter that controls the stability of coal ribs in underground mines. Estimation of the UCS of coal units composing the rib is required for conducting the rib stability assessment technique. This technique requires conducting large numbers of conventional UCS tests in a laboratory, which are expensive and time consuming. The research work outlined in this paper examines the use of indirect strength estimation methods—the point load test (PLT) and the in-situ Schmidt hammer test (ISHT)—for evaluating the intact strength of coal. The conventional UCS test was conducted on 80 coal specimens from 10 different coal seams for eastern coals. For each coal seam, the PLT and the ISHT were compared with the UCS test results to establish a correlation between the strength indices from the PLT or ISHT and the UCS. Moreover, to simplify the estimation of the UCS, a correlation between the megascopic coal lithotype and UCS was established.INTRODUCTIONBased on Mine Safety and Health Administration (MSHA) reports, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States over the past decade (MSHA, 2018). In an attempt to control rib failures in underground coal mines, the National Institute for Occupational Safety and Health (NIOSH) is working on developing a coal rib stability rating technique to provide a quantitative means to characterize the stability of coal ribs and to provide guidelines for early selections of rib support. The unconfined compressive strength (UCS) of coal units composing the ribs is one of the key input parameters required to estimate coal rib stability. The UCS of coal is an important parameter that controls the resistance of coal ribs to fracturing and slabbing. Direct determination of the UCS is time-consuming and expensive. Moreover, the UCS may be limited to testing only the strong coal samples since the weak or highly cleated samples might not survive the transportation and the preparation process (cutting and grinding). Therefore, alternative methods have been tested to indirectly find the intact strength of coal, such as the point load test (PLT) and the in-situ Schmidt hammer test (ISHT). The acronym ISHT refers to Schmidt hammer tests that were conducted in-situ on coal pillar ribs, while the acronym SHT refers to tests that were conducted on small scale blocks of coal."

Jan 1, 2018

By J. Frederick Stampfer

Current certification testing of self-contained breathing apparatus includes tests with human subjects wearing the apparatus while exercising. During these tests, certain apparatus variables are measured during rest periods. Because of concerns that the present tests may not accurately simulate the stresses to which an apparatus is subjected in the field, the Bureau of Mines proposed new human subject tests. It was also felt that different measurement techniques would supply more reliable data on the apparatus response to these stresses. The Los Alamos National Laboratory was asked by the Bureau to evaluate the proposed tests and monitoring techniques. The major conclusions derived during this study are these: (1) The proposed tests are not too physically demanding. (2) As long as human test subjects are used, a minimum subject weight should be required for certification tests. (3) Important apparatus variables are the breathing resistance, temperature, and carbon dioxide and oxygen concentrations of the inhaled gas. (4) Continuous monitoring should be used, rather than monitoring only during rest periods. (5) New pass/fail criteria based on realistic estimates of the user's physiological requirements, as tempered by present and future engineering limitations, are needed. (6) When available, breathing machines, rather than human subjects, should be used for most certification testing. (7) A more realistic ergonomics test than that proposed is needed. (8) A gas leak test for the system and a facepiece leakage test are also needed.

Jan 1, 1983

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By L. Shasko

Deliberative mapping is a method of public engagement designed to bring citizens and specialists together to inform policy decisions in conflict-laden areas of science and technology (Stirling and Davies 2004a). Citizens and specialists participate in the process both separately and together. A deliberative mapping study was held in Regina, Saskatchewan in October and November of 2019. Participants in the study assessed options for reducing greenhouse gas emissions in small, remote or off-grid communities, including assessing the role of small modular nuclear reactors (SMRs) in climate change mitigation. Deliberative mapping is designed to facilitate direct, two-way conversations between citizens and specialists through both formal and informal discussions. The relationship building component of this process may increase trust. Public consultation processes that lack two-way dialogue or are seen as obligatory rather than meaningful can worsen public opposition or lead to negative public perceptions. Public education alone is not enough to change public opinion. Providing people with more information on topics they already hold opinions on can work to reaffirm previously held biases, but building relationships can provide new pathways to overcome divisions and turn close-mindedness into open-mindedness.

Jan 1, 2020

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for Zambia for the period from 1970 through 1981. The work done through the Bureau of' Mines, Minerals Availability Program, under Contract number J0225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) timber and lumber, 6) fuel, 7) powder and blasting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983

By Winton Gale

"Rock and coal fractures and micro seismic vibration are common occurrences during development mining. It is very uncommon for coal and rock to be propelled into the roadway during normal mining operations. However, such occurrences do occur and appear to require significantly more energy than is available from strain energy release during coal cutting. The sources of energy, which can contribute to the propulsion of coal from the face or ribs, are typically strain energy from the surrounding ground, seismic energy from a rapid rupture of the ground in the vicinity, or rapid expansion of gas from within the burst source area.The aim of this paper is to briefly review the bursts that could be related to strain energy or seismic energy. However, the greatest emphasis is placed on the effect that gas within the coal could play in moderate to gassy mines.It has been found that the bursts related to the expansion of gas can occur in coal and stone. The volume of gas involved in coal bursts is typically lower than in gas outbursts; however, the process is generally similar.INTRODUCTIONA coal burst is defined as a rapid expulsion of coal (and potentially gas) from the boundary of the roadway. The volume of a burst can be variable, but volumes above 10-50m3 are noted and cause significant disruption to operations.Rock and coal fracturing is common about roadways, particularly under the influence of elevated stresses, either tectonic or related to mining abutment stress. Shear fracture is very common; however, it is very uncommon that the coal is propelled from the face or ribs as a result of fracture of the material. The nature of rock fracture about roadways under elevated stress is presented in Figure 1.A burst requires energy to propel the coal or rock from the rib or face of the roadway. The depth of material impacted may vary from 0.5m to greater than 3m inside the roadway boundary. The strength of the ground in this zone is variable depending on the nature of the coal seam (or surrounding material). Typically, this material has significant residual strength as confinement increases into the ribside.The energy required to propel this material is typically in addition to that which is associated with normal fracturing about the roadway."

Jan 1, 2018

By Michael Brandner

In the past the research and development of new materials for hot mill rolls was mostly done by trials. Such trials are expensive and difficult to transform from small size to the big size of a solid roll. Computation is the cheaper way to get ideas processed and can be varied in different directions. The main part before simulation is the generation of the needed basic data of the specific materials. Some data is already well known and can be bought from databases; others have to be done specifically for our materials. The evaluation of such results has to be done still with solid trials, but the number of trials can be reduced. The advanced techniques of finite element calculation offer a wide range of possibilities to get answers about alloys, solidification, casting parameters and their influence. The possibility to calculate a heat treatment cycle and to get an answer about the internal stress modification during the cycle is a great help to understand the principle of transformation. Examples of different calculations in various fields will be given. The close cooperation with universities and other research institutes as well as the in-house possibilities will be presented.

Jul 30, 2018

By L. O. Cooper

IN THE operation of most mines, hoisting ropes, made of steel, play a very important part in the conveying of men and material between surface and the underground workings. It is obvious that, in order to maintain a maximum degree of safety, certain restrictions must be placed on the loads that may be carried by hoisting ropes, as well as on other factors that may affect the life of the rope. It is the purpose of this paper to suggest ?a new method of defining the necessary restrictions. The three main stresses in a hoisting rope are the static stress, bending stress, and dynamic stress. Crushing stresses, which are also present, are largely indeterminate and may best be allowed for by proper grooving of drum and sheaves, by adequate inspection of cross-over points, and by limiting the number of layers on the drum. They will, therefore, not be considered in this analysis. In the ?recent Ontario regulations, the limiting conditions for the main stresses are specified separately. The static stress is limited by setting a minimum static safety factor of 5.0 The dynamic stresses are allowed for by specifying a minimum capacity factor of 8.5, which has the effect of increasing the safety factor required at smaller depths in a uniform manner. The bending stresses are limited by calling for a drum-dia./rope-dia. ratio of at least 60 for ropes up to 1 inch in diameter and 80 for ropes greater than 1 inch in diameter. One disadvantage of this method is that the controls are too rigid and do not allow the operator sufficient freedom of action within safe limits.

Jan 1, 1951