Search Documents

By R. N. Edwards

The Magnetometsic Resistivity (MMR) method is based on the measurement of the low-level, low-frequency magnetic fields associated with non-inductive current flow in the earth. The traditional resistivity method maps the electrical properties of the earth by measuring the electric field caused by galvanic current flow between a pair of current electrodes. The MMR method differs from it in that the potential electrodes are replaced by a sensitive coil or magnetometer and a component of the magnetic field due to the current flow is recorded. The presence of an inhomogeneity redistributes the current flow which results in a perturbation of the electric field and, usually, of the magnetic field. The electric field immediately above a relatively conductive inhomogeneity must, by Ohm's Law, be smaller than that expected for a uniform earth. The current density in this region is also reduced but the current density within the inhomogeneity itself is enhanced so that the horizontal component of the magnetic field measured above the inhomogeneity is usually larger than that expected for a uniform earth. A method of interpretation using the magnetic anomaly was patented by Jakoskyl in 1933 but it met with little success at that time. Part of the problem was undoubtedly with the instrumentation, and only recently have robust instruments of sufficient sensitivity been developed2 and field data of good quality obtained. There are many common configurations of the potential and current electrodes in the resistivity method. Similarly, in the MMR method one or both current electrodes may be moved with the magnetometer, either horizontally or vertically ( in a bore-hole), or the current electrodes may be maintained in fixed positions and the magnetometer alone moved. The MMR anomaly is defined as the difference between the

Jan 1, 1975

By C. Brown, N. Rayyan, T. H. Dubaniewicz

Lithium-Ion batteries (LIBs) have the potential to go into thermal runaway which introduces a new ignition source in hazardous environments such as gassy underground mines that may contain methane in the surrounding air. Researchers from the National Institute for Occupational Safety and Health (NIOSH) used an accelerating rate calorimeter (ARC) to induce thermal runaway in individual lithium-titanium-oxide (LTO) and lithium-nickel-cobalt-aluminum-oxide (NCA) LIB cells within a sealed enclosure with either no methane, a lean, a stoichiometric, or a rich methane-air mixture in the surrounding canister to determine if these LIB types would ignite the methane, causing an additive effect on overpressures. Canister pressures and maximum temperatures reached by the cells, surrounding air, and exhausted gases were measured in this study and remained consistent with varying methane concentrations.

Feb 1, 2023

By Lawrie Logan, Mike Wiggin

This paper will be in two parts, a discussion of the benefits available from benefit sharing as a concept followed by an examination of how this approach was applied at Mesa J Mine and what improvements were made. The first part is an outline of the ways that both parties in a benefit sharing agreement can uncover additional wealth by bringing a new approach to the relationships between mine and supplier. The paper describes a partnering agreement recently established between Robe River Iron Associates (RRIA) and Dyno Nobel Asia Pacific Ltd (DNAP) to access the wealth locked up by the usual explosives supply contracts in Australia and elsewhere. The partners are acting cooperatively to maximise the benefits to both parties from optimising blasting practices at the Mesa J Iron Ore Mine in the Pilbara region of Western Australia.

Jan 1, 2001

By A. M. Skov, L. F. Elkins

First response to large-scale water flooding in the fractured very low permeability Spraberry sand has led to a new unique cyclic operation. Capacity water injection is used to restore reservoir pressure. This is followed by marly months production without water irzjection and the cycle repeated. Expansion of the oil, rock and water during pressure decline expels part of the fluids but capillary forces hold much of the injected water in the rock. At least with reservoir pressure restored and with partial water flood development, field performance has proved this cyclic operation is capable of producing oil from the nzatrix rock at least 50 per cent faster and with lower water percentage than is imbibition of water at stable reservoir pressure. INTRODUCTION The Spraberry Field of West Texas presents unusual problems for both primary production and water flooding. Extensive interconnected vertical fractures in the fractional-md sandstone permitted recovery of oil on 160-acre well spacing, but they made capillary end effects dominant. Primary recovery by solution gas drive is less than 10 per cent of oil in place. The concept of displacement of oil from the sand matrix by capillary irnbibition of water has led to field techniques which promise greatly increased oil recovery. Free exchange of laboratory research, reservoir information and results of field pilot tests among the various companies has been very important in development of this technology. Five units covering a total of 170,000 acres have been formed for water flooding, and 10 other areas covering an additional 175,500 acres are in various stages of unitization. Part of the Driver Unit reaching fillup first has demonstrated very unusual waterflood behavior and indicated numerous operating problems that will develop within and among the various units. SPRABERRY ROCK AND PRIMARY PERFORMANCE The Spraberry, discovered in February, 1949, is a 1,000-ft section of sandstones, shales and limestones with two main oil productive members: a 10-15 ft sand near the top and a 10-15 ft sand near the base. In part of the field some thinner intermediate sands are oil productive, and others are water bearing. All sands have permeabilities of 1 md or less and porosities of 8-15 per cent. Ordinary core analysis and electric and radiation logs are ineffective in differentiating between oil productive and nonprcductive sands. Sands capable of containing producible oil are best identified by mercury injection capillary pressure measurement and, in some cases, by core water saturation. About 3,500 wells have been drilled in the 500,000-acre trend. Vertical fractures were observed in practically all Spraberry cores. Continuity and interconnection of fractures were confirmed by pressure interference among wells during early development.' Major fractures trend northeast-southwest as indicated by oriented cores and confirmed by five fluid injection tests, by analysis of the pressure transients observed during development,''' and by three interference tests in the Driver Unit Water Flood reported herein. Fracture spac- ing probably averages inches to a few feet. Spraberry wells typically produced 100-400 BOPD initially after hydrauLic fracture treatments. By 1962 oil production had declined to an average of 12 bbl/well/day, near the economic Limits of operation. Reservoir pressure had declined from 2,300 psi initially in the Upper Spraberry and 2,500 psi in the Lower Spraberry to 500-1,000 psi. Partial closing of the fractures with declining reservoir pressure is believed to be the cause of such low oil production rates at these relatively high reservoir pressures. Cumulative recovery of 208 million bbl of oil is 80 to 90 per cent of that recoverable by primary means. Performance of the entire reservoir is summarized in Fig. 1. IMBIBITION WATER FLOODING By 1952 reservoir performance indicated low primary recoveries. Most engineers, expecting serious channeling of injected fluids through the fractures, held little hope for secondary recovery. With its extensive background of research on the fundamentals of fluid flow within reservoir rocks, Atlantic's Research and Development Division on short notice in 1952 conceived that displacement of oil by capillary imbibition of water into the rock might significantly increase Spraberry recovery. Laboratory data reported by Brownscombe and Dyes scaled to probable reservoir conditions showed potential waterflood recovery equal to or greater than primary recovery with a 10-15 year flood life.= A pilot test using three 40-acre injection wells, one central producing well and 18 surrounding observation wells demonstrated technical feasibility of the process. Injection of 1.5 million bbl of water from November 1952 to August 1955 proved water entered the rock and displaced oil

By K. Duffy, W. Valery, L. Pyle, P. Holtham

A conceptual scoping study was conducted to investigate pre-concentration options for upgrading ore from an Ag-Pb-Zn deposit. The low grade of the ore would result in only modest economic returns, given current market conditions. Several pre-concentration options were considered. These included: selective mining, crushing and pre-screening (following either standard or high intensity selective blasting), bulk ore sorting, particle sorting, jigging, dense medium separation, or combinations of these approaches. Flowsheets were developed for each option, and the upgrade performance was modelled using Limn to determine mass balances and stream tables. Due to the limited availability of test work data, the models were based not only on what test data was available but also on case study data found in the literature. The Bazin technique was used to derive assay by size data for different streams following crushing. Equipment lists and preliminary layouts were established based on the stream tables, and capital and operating costs were estimated for each flowsheet. This information was used to carry out a preliminary economic evaluation using net present value and sensitivity analysis. In this case, the most economically attractive process was found to be particle sorting; although further benefits may be realised by combining with bulk sorting. This paper describes the methodology used and the key findings of the study. Keywords: Pre-concentration, pre-screening, ore sorting, jigging, Ag-Pb-Zn, particle sorting, bulk ore sorting

Jan 1, 2020

By G. L. Bloomsburg

This report describes work which was done to apply an existing finite element computer program UNSAT2 to the unsteady, unsaturated flow of water through waste shale piles. The work was done in three phases: 1. Verification of program through comparison with existing data. 2. Verification of program through simulation of flow from field seepage ponds at Rifle, Colorado. Considerable laboratory work was done in this phase to obtain capillary pressure-saturation-relative permeability data and hydraulic conductivity values for retorted shale. 3. Application of program to flow due to natural rainfall in a section through the Piceance Basin in Colorado, and a typical waste shale pile.

Jan 1, 1978

By L. K. Weaver

The purposes of this Bureau of Mines report are to review the history of the domestic offshore hydrocarbon production; to project offshore oil and lease condensate production from 1971 through 1985; and to show the impact of offshore development on the onshore segment of the petroleum industry. Since 1954, offshore production has provided an increasingly larger portion of the domestic oil production. Domestic offshore oil and lease condensate production has increased from about 2.0 pct of the U.S. total in 1954 to 16.7 pct in 1970. Likewise, marketed gas production has increased from 1.0 pct of the U.S. total in 1954 to 15.0 pct in 1970. The past performance of exploration, leasing, development, and production of the offshore petroleum industry was used to make projections of offshore oil production. A comparison between onshore and offshore operations was also made. Assuming a tentative Department of the Interior offshore leasing schedule is completed by 1980, the authors estimate that by 1985, about 30 pct of domestic crude oil and lease condensate production from the lower 48 States will come from offshore areas. Currently, leasing of Federal offshore areas has been delayed due to environmental considerations. The rate at which off-shore hydrocarbons will enter the energy market will depend, to a large extent, on how soon environmental considerations are resolved. Assuming that offshore leasing will resume in the near future, U.S. offshore production of crude oil and lease condensate should be about 934 million barrels in 1985.

Jan 1, 1973

Beyer Barometric Condenser The Ingersoll-Rand Co. is now offering to the trade complete steam­condensing plants for all service conditions. This equipment includes the Beyer barometric condenser, for' which the company has secured the patent rights, Imperial duplex and Ingersoll-Rogler straight-line reciprocating dry vacuum pumps and, where required, Cameron simplex and centrifugal pumps. The Beyer barometric condenser is of the counter-current type, in which air and cooling water flow in opposite directions. The steam inlet is at the bottom of the condensing v el, the water inlet above and the air-removal opening at the top. The sheets of cooling water over owing the pool at the inlet point meet the entering steam. The two are brought into intimate contact by conical baffle plates which assist the water to absorb to its full capacity the latent heat of the steam. The non-condensable air liberated in the condensing action rises through the falling water to the removal point at the top, being cooled to practically the temperature of the incoming water. It is also to be noted that ample opportunity is given for the removal of the air content of the water before

Jan 8, 1916

THE CHAIRMAN.- This meeting is under the auspices of the American Institute of Mining and Metallurgical Engineers, and I think the germ of the idea originated in the steel business. Last year there was a meeting of prominent people in the steel industry with the idea of getting together and discussing practical phases of their business, so that everybody could contribute and from that there might be benefit derived for the industry. Several months ago when Mr. Bain was in Salt Lake City, he and Mr. Oldright asked me what I, as an individual, thought of it. From that originated this idea of having the copper people come together to discuss reverberatory smelting and all its phases. In starting out, it seemed the best plan to ask members what particular subjects they wished to discuss first; that is, the ones that would be considered more important. We asked Mr. Oldright, or suggested sometime ago that the meeting be postponed until May because May is a lovely month in Salt Lake. There are a number of attractive features around the city. We have a number of smelters here and I think that probably the most of the benefit will be derived from talking in an informal way and visiting the various plants around. the valley. At any rate, speaking as a resident of Salt Lake, I am glad to see all of you gentlemen here, and hope you have an interesting and instructive time. The tentative list of subjects for discussion at this conference is as follows: Construction Walls, etc. Walls, proper design and thickness of brick for various types of charging. Bottoms, construction of. Binding steel, correct weight and arrangement, where thrust of arch should be taken. Refractory materials, feasibility of using different material in various parts of the furnace. Water jackets, where applicable. Should bricks be used inside of same. Gas space, proper design for, height of roof above bath, etc. Roof Shape of Roof, in hot zone and elsewhere, longitudinally. Construction of roof, in various zones, around openings.

Jan 1, 1930

By A. J. Farstad

Electromagnetic location tests were conducted by Westinghouse Georesearch Laboratory under the sponsorship of the U. S. Bureau of Mines at the Galena Mine in Northwest Idaho. The objectives of these tests were to evaluate the performance in deep hardrock mines of an electromagnetic location system previously developed for the U. S. Bureau of Mines for use in coal mines. Tests were performed using long wire transmitting antennas as well as horizontal and vertical transmitting loops at depths from 3000 feet to 4300 feet (995 metres to 1311 metres). Surface measurements were made of magnetic field strengths, field strength patterns, and background noise, These measurements were compared with theoretical predictions for a homogeneous ground conductivity consistent with this particular geologic region. The results of the Galena Mine tests show conclusively that light-weight portable electromagnetic transmitters can be effectively utilized to provide uplink communications and location information in deep hardrock mines. Typical metal mines such as Galena utilize deep vertical shafts for mine access and haulage and these shafts produce signal enhancement at the surface from underground electromagnetic transmitters by as much as 30 dB. The results also show that horizontal wire configuration can serve as an effective alternative to the magnetic dipole antenna as a rescue transmitting antennaa and can be used when the required area is not available for deployment of a loop antenna. In spite of the electromagnetic coupling effects observed in the vicinity of the shafts, the location accuracy obtained still provided useful information on the general location of the transmitting sources involved. The horizontal wire location accuracy was within 46 metres, while the vertical magnetic dipole and the horizontal magnetic dipole accuracies were within 152 metres and 110 metres respectively at a 915 metre depth.

Jan 1, 1973

By Brent A. Elliott, J. Richard Kyle

Texas is a major producer of industrial mineral resources required by the state’s ever-growing population that now exceeds 28 million. Texas typically ranks in the top three states for the value of non-fuel mineral production with a total value of $5.2 billion in 2017, accounting for 6.9% of the total US mineral value. Almost 90% of current Texas industrial mineral value comes from the production of cement, crushed stone, industrial sand, and construction sand and gravel. Construction material consumption is focused in the 25 metropolitan areas of the state with populations of > 100,000 residents. Industrial mineral consumption is dominated by the four most populous regions of the state—Houston, Dallas-Fort Worth, San Antonio-New Braunfels, and Austin-Round Rock—with an aggregate population of more than 18 million. More than 11,000 employees work in Texas mining and processing operations. Texas produces more crushed stone than any other state from more than 200 quarries; a similar number of operations produce sand and gravel. Specialty industrial sand production for use as proppants in hydraulic fracturing for enhanced petroleum production serves as an excellent example of how developments in one industry sector can markedly affect another industry; the production of industrial sand in Texas has markedly increased over the past decade, reaching $1.3 billion in 2014. With Texas’ population projected to reach 50 million by 2050, continuing in-state development and production of industrial minerals will be required to supply its residential, commercial, and industrial users. Favorable geology and economic factors provide opportunities for identification and development of new industrial mineral production sites.

By Maurice C. Fetzer, Charles R. Austin

It has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A1 critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publicationsl,2 have shown that the factors controlling graphitization below the A1 are different from those operating above the A1 inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemical analyses. Many years ago it was recorded3 that the rate of graphitization at subeutectoid temperature is not a maximum just below the A1 critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is impossible to spheroidize certain steels in the temperature range of 650° to 710°C. without the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A1 (720°C.) these same steels may be completely sphe-roidized at constant temperature. In previous studiesl,2,4 on I per cent plain carbon steels graphitization was encountered during prolonged tempering. The limited number of steels studied did not provide sufficiellt data to permit adequate study of the factors controlling this graphitization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, furnished by four steel companies, who also supplied information regarding the history of manufacture. An extensive program of research is being carried out on these steels, including the effect of pretreatment and atmosphere on the nature and extent of graphitization, and the possible correlation of graphitization with such characteristic properties as hardenability, grain size and mechanical behavior. In the present paper discussion is restricted to a study of the correlation between graphitizing tendency at 670°C. after quenching from several temperatures above the critical, and (I) the minor variations in the chemistry of these steels of "similar" chemical composition, and (2) the deoxida-tion practice employed. The state of the lead bath, oxidized or protected from oxidation by charcoal, used in the tempering treatments is also considered. Materials Eighteen plain carbon steels of about I per cent carbon, and containing similar amounts of each of the other common elements usually found as impurities, were obtained in the form of rods % in, in diameter from four steel manufacturers. The analyses for ordinary and special elements of all the steels were made on the rod stock as received in the laboratory, and the re-

Jan 1, 1941

By Maurice C. Fetzer, Charles R. Austin

It has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A1 critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publicationsl,2 have shown that the factors controlling graphitization below the A1 are different from those operating above the A1 inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemical analyses. Many years ago it was recorded3 that the rate of graphitization at subeutectoid temperature is not a maximum just below the A1 critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is impossible to spheroidize certain steels in the temperature range of 650° to 710°C. without the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A1 (720°C.) these same steels may be completely sphe-roidized at constant temperature. In previous studiesl,2,4 on I per cent plain carbon steels graphitization was encountered during prolonged tempering. The limited number of steels studied did not provide sufficiellt data to permit adequate study of the factors controlling this graphitization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, furnished by four steel companies, who also supplied information regarding the history of manufacture. An extensive program of research is being carried out on these steels, including the effect of pretreatment and atmosphere on the nature and extent of graphitization, and the possible correlation of graphitization with such characteristic properties as hardenability, grain size and mechanical behavior. In the present paper discussion is restricted to a study of the correlation between graphitizing tendency at 670°C. after quenching from several temperatures above the critical, and (I) the minor variations in the chemistry of these steels of "similar" chemical composition, and (2) the deoxida-tion practice employed. The state of the lead bath, oxidized or protected from oxidation by charcoal, used in the tempering treatments is also considered. Materials Eighteen plain carbon steels of about I per cent carbon, and containing similar amounts of each of the other common elements usually found as impurities, were obtained in the form of rods % in, in diameter from four steel manufacturers. The analyses for ordinary and special elements of all the steels were made on the rod stock as received in the laboratory, and the re-

Jan 1, 1941

By J. Kolacz

"A new sensor based sorting system has been developed, providing a possibility for laboratory scale testing and further scale-up of the separation results to the industrial operation. The new system contains different sensors as: X-ray detectors, visible light cameras, NIR cameras, ultraviolet cameras and magnetic sensors, in the same sorting unit. The sorting unit allows advanced calibration options and fine-tuning of the installed sensors to achieve the best separation effect under controlled conditions. Finally, the processed material can be analysed and separated by the rejection mechanism, similarly to the industrial scale operation. At the same time, the process is carried out with limited amount of material allowing detailed statistical calculations for processed particles and all sensor types. The optimal settings and sensor types are specified for the industrial application.The paper describes the scale up of the results achieved for iron ore and coal, where the test work was first carried out using the new laboratory sorting system and where the industrial scale sorting system has been built, in the final stage. The industrial scale sorting results showed a very good correlation between the laboratory and full scale operation. Thanks to the detailed study carried out in the laboratory equipment, the settings of the sensors in the full scale operation provided much better separation efficiency. It was especially important to provide proper setting for the X-ray sensor data calculations, which can be very critical for achieving the best results. During the industrial scale sorting of coal, the input material had 40-55% rock particles as the direct source of ash in the coal stream. The optimal laboratory unit settings and transferring these settings to the industrial sorter, provided 98.8% efficiency for removing rock particles with only few % losses of coal."

Jan 1, 2016

By G. E. Pralle

INTRODUCTION The decade from 1969 to 1979 saw the crest of a wave of investments by companies and investors, primarily from the major industrial nations, in the metals and minerals industries of the so-called lesser developed countries. This was brought about by two major considerations: 1). The higher ore grades and therefore the higher profit potential of the mineral deposits in the third world countries, and 2). The desire, particularly by the European countries and by Japan, to ensure a safe supply of raw materials not available in their own countries. The decade began with the start of the Toquepala mine in Peru and the major investments in the Bougainville mine in Papua New Guinea and the Ertsberg mine in Indonesia. It ended with the start-up of Southern Peru Copper Company (SPCC) Cuajone mine in Peru and Inco's Soroako mine in Indonesia and the investments in several major alumina or aluminum projects in Australia and Brazil. Concurrent with this huge flow of funds into the mineral resources industry of the developing world was the build-up of a psychological fear in the host countries of exploitation/domination by the foreign investors. This resulted in an increasing trend towards: 1). Nationalization of existing mineral ventures, and 2). Tougher legal/fiscal frameworks for new ones. NATIONALIZATION Nationalization appeared in its earliest form as "Mexicanization" of the petroleum industry in Mexico in the 1930's, followed later by Mexicanization of the mining industry in general. This was enacted with the Mexican Mining Law of 1961 which required that 51% of the equity be owned by Mexican nationals. Later in the decade the equity share for foreign investors was reduced to 33 1/3% for the developers of the Frasch sulphur operations in the Isthumus of Tehuantepec. However, the law was not fully implemented in the copper industry until late 1970 with the purchase of 51% of the ownership in the Cananea Mining Company. The trend toward nationalization of the copper industry progressed to Chile where in 1967 under the Government of Eduardo Frei the major North American copper companies were induced to sell a one-half interest in their Chilean mines to the State. Likewise, in 1970, "Zambianization" took place, when the two major operating companies Roan Selection Trust (Amax) and Zamanglo (Anglo American) were restructured into Roan Consolidated Mines (RCM) and Nchanga Consolidated Mines (NCCM) providing the government with 51% of the equity ownership. Whilst the earlier forms of nationalization in general constituted a fairly priced buy-out (El Teniente, Chile for US$80 million, RCM for US$117.8 million, NCCM for US$178.7 million), the total nationalization of the Chilean mining companies in 1970 under Salvador Allende did not. Later, "Western" countries joined this trend and on October 29, 1973, Mr. Gough Whitlam proclaimed that "overseas capital must continue... in partnership with Australian capital" and "in some special energy cases we have an objective of 100% Australian ownership". In 1974 Mr. Pierre Trudeau stated: "The Liberal Party of Canada sets as an objective that new resources projects in the natural resource field should have at least 50% and preferably 60% Canadian equity ownership". FOREIGN INVESTMENT The situation for the foreign investor in the worldwide resource industry rapidly deteriorated from then on. New features appeared in mineral exploitation and operating agreements, centering not only on local government/local companies ownership but also on increased taxation. The new tax rate (mineral tax, royalty, and income tax) for the semi-government companies NCCM and RCM in Zambia became an effective 73%. Likewise the much publicized and discussed renegotiated Bougainville agreement brought dramatic increases in the total "take" by the PNG Government. More innovative forms of indirect taxation made their appearance and were added to the normal tax burdens of the mineral industry which already

Jan 1, 1985

By F. Schreiter

"One method to increase the exploitation rate of a mine is the use of backfill with residual materials in exploited areas. The backfilled material is meant to support both, the walls of galleries and pillars as well as the roof of mining openings. With increasing depth, the exploitation rate diminishes fast, thus the application of backfill in order to change the layout of the mine is crucial for economic success. In result of using backfill, it is possible to change the layout of the working area with a higher ratio to excavated areas and less area occupied by pillars. Thus it is possible to boost the output of a mine by using backfill. Setting the criteria for the selection of the best possible materials and whose improvement, it is useful to know about their qualities and handicaps. The Mining Department at TU Bergakademie Freiberg is analyzing the parameters of residues from different processing methods, accrued in plants of different potash mines and blending different residues for optimization of material attributes. These were significantly characterized by basically parameters like the size and the distribution of different diameters of the grain material. INTRODUCTION The chair for underground mining methods at TU Bergakademie Freiberg is tasked with the sufficient and sustainable supply of economics with raw materials. The steady high demand, the rising prices and the finiteness of the deposits are reasons for the need of an optimized economic utilization of natural deposits, a continuous improvement of mining technics and technology. From an ecological and economical position the best possible utilization of the resources has to be achieved. Many mining operations are by reasons of the deposit not able to haul valuable minerals only, they have to haul a mixture of valuable minerals and waste rock. This hauled combination is given into the processing plant for separation and enrichment of the valuable mineral. The residuals of the processing are commonly dumped to a waste rock pile. For minimizing the size of such a waste rock pile and also minimizing the ecological footprint of a mining operation the only way is minimizing the quantity of accruing waste rock material. Both, optimization of economic utilization and also minimization of waste rock dumps can be realized in one by backfill with processing waste rock material in mined out areas. Especially in mines, mined by room and pillar method, smaller dimension of the pillars are sufficient for safety and stability. By the way less valuable minerals have to be leaved back in the mine and the mine outcome is increasing."

Jan 1, 2015

By D. R. Lentz, S. H. Mcclenaghan, J. A. Walker

"Abstract - The Orvan Brook deposit is one of several (Zn+Pb>>Cu)-rich sulfide deposits hosted by the Spruce Lake Formation (California Lake Group) in the northwestern part of the Bathurst Mining Camp. This parautochthonous deposit is hosted by a narrow band of highly deformed, locally graphitic shale that appears to conformably overlie felsic volcanic rocks of the Spruce Lake Formation, and is in tectonic contact with overlying mafic volcanic and related sedimentary rocks of the Canoe Landing Lake Formation. The Spruce Lake Formation is dominated by felsic volcanic rocks and subordinate fine-grained sedimentary rocks, and mafic volcanic rocks (Canoe Landing Lake member). The felsic volcanic rocks can be divided into aphyric and feldspar-phyric rock types. The feldspar-phyric rocks and a few of the aphyric varieties have a Zr/TiO2 ratio of 0.06, and fall into the California Lake Group field on a Y/TiO2 versus Zr/TiO2 diagram. In contrast, the aphyric felsic volcanic rocks have Zr/TiO2 ˜ 0.09 and are marked by high Zr and Th, which is consistent with highly fractionated felsic magma of Spruce Lake affinity. Major and trace element analyses of host rocks suggest that weak to moderate hydrothermal alteration developed on the south side (stratigraphic footwall) of the deposit, which is consistent with a north-younging succession. The sulfide lens strikes east-west for approximately 2.3 km, extends down-dip for at least 500 m locally, and has an average thickness of between 0.75 and 1 m, but is locally up to 5.5 m thick. The contacts of the massive sulfide lens with its host rocks are invariably sharp. Host rocks show evidence of intense ductile deformation as well as later brittle deformation. Compositional layering and sulfide breccia textures in the sulfide body are interpreted to result from deformation or tectonic enhancement of original primary layering. The deposit contains an estimated resource of 2.69 Mt grading 1.73% Pb, 5.95% Zn, 0.37% Cu, 72 g/t Ag, and 0.9 g/t Au. Similarities in bulk d34S between the Orvan Brook (+8.6‰) and the nearby Cu-rich McMaster deposit (+8.2‰) suggest a common depositional setting."

Jan 1, 2006

By Carlos Martins de Oliveira

The trucking industry is constantly seeking improvement and cost reduction of their vehicles, studying new lighter and robust materials to meet the needs of its customers. The objective of this work is to study the application of DCPD Telene, PU. R. RIM and PP-TD 20 materials in aesthetic components of trucks: bumper, calender, upper and lower bracket and side air deflector. A multifunctional work team was created to work in such parts of IVECO trucks. The work began with an analysis of possible improvements to the current parts and followed the subsequent phases: definition of new materials, virtual modeling, new tools, and durability test in vehicles. It could then be verified that the proposed DCPD Telene, PUR. RIM and PP-TD 20 materials showed greater strength, better painting surface, and reduced weight and cost in parts.

Aug 8, 2018

By C Simpson

In 2011 the forecasted world demand for iron ore continues to grow, and during this time Australia is looked upon as a reliable supplier of high quality ore. The expansion of the current Australian mines is unlikely to meet the forecast demand. New mines are therefore being actively explored for and when discovered, are quickly being developed into mines in order to meet the world’s hunger for steel.The Solomon Project area is a large new iron ore discovery, located in the central Hamersley Ranges of the Pilbara province in Western Australia. The first Fortescue exploration drill holes commenced on the project in 2007 and to date three billion tonnes (Bt) of iron ore have been defi ned within the project area. Fortescue is fast-tracking the development of the ‘Solomon Stage 1’ project, with rail and mine construction commencing during 2011, and ore to be railed to Fortescue’s existing shipping operations at Port Hedland commencing in 2012. At a designed production rate of 60 Mt/a, the Solomon operation will be one of the biggest production centres of iron ore in the Pilbara.Deposit types include the three dominant mineralisation styles of the Pilbara province, being bedded iron deposits (BID), Channel iron deposits (CID) and detrital iron deposits (DID). All these mineralisation styles are present in large concentrations within the Solomon project area, and when mined will produce two product streams. These are a single product of CID, and a combined product from a blend of BID and DID material.This paper defines the geological characteristics of the Solomon iron deposits as recognised through the exploration and development of this vast resource over the three years since exploration commenced on the project.

Jul 11, 2011

By Jared Onyirimba, Jim Viellenave, Hal Demuth, Dale Verran, Chad Sorba, Errol Lawrence, David Bronkhorst

As outlined within the Denison Mines Corp’s (“Denison”) Pre-Feasibility Study ("PFS") completed in late 2018, additional work is required to increase confidence and reduce risk associated with the application of the In-Situ Recovery (“ISR”) mining method at the Phoenix deposit, located on the Wheeler River Uranium Project (“Wheeler River” or the “Project”) in northern Saskatchewan. The successful application of ISR in any geological environment largely hinges on three fundamental requirements, 1) permeability (of the deposit), 2) containment (of the mining solution) and 3) leachability (of the mineralization). Denison has designed several staged technical programs to progressively reduce risk associated with these requirements as the Company advances the Project toward a Feasibility Study (“FS”) and Environmental Impact Assessment (“EIA”). This paper will discuss the scope and results of certain technical programs being undertaken as the Company aims to develop the first ISR mining operation in the Athabasca Basin.

Jan 1, 2020