Search Documents

By Sunil Arora, Lisheng Shao, Chris Conkle

"The East Garden Grove - Wintersburg Channel located in Orange County, California, required upgrades along the levees to mitigate potential liquefaction and lateral spreading hazards. The Orange County Public Works designed soilcrete columns constructed between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue (approximately 2,500 ft), and along an approximately 2,000-ft-long stretch of the south levee. The earthen embankment, approximately 13- to 15-ft high and damaged significantly by erosion, was then excavated to widen the channel to increase the channel flood conveyance capacity.The site is located within the Los Angeles Basin, underlain by several thousand ft of marine sedimentary strata. Uncontrolled fill materials were encountered to approximately 10 ft below ground surface, underlain by tidal and flood plain deposits. Groundwater was encountered at sea level, which is approximately 10 ft below grade.This paper will discuss site soil conditions, and the construction and quality control of soilcrete columns constructed by wet soil mixing; also, the paper will introduce the Drilling Index (DI) as a measurement tool, similar to the cone penetration test (CPT), to evaluate the soil strength in more detail. Finally, the statistical analysis of soil mixing strength distributions for the project quality control will be presented.INTRODUCTIONWintersburg Channel in Orange County, California, required ground improvements along the existing levees to mitigate potential liquefaction and lateral spreading under the site design earthquake. Orange County Public Works designed and developed a cellular pattern of soilcrete columns sandwiched between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue, and adjacent an approximately 2,000-ft-long stretch of the south levee (Fig. 1). An earthen embankment approximately 13 to 15 ft high, damaged significantly by erosion, was then excavated to widen the channel and increase the channel flood conveyance capacity.Stiff, soilcrete cellular wall structures can reduce the earthquake-induced cyclic shear stress ratio (CSR) in the soil within the cells, thus preventing excess pore water pressure build up which may trigger soil liquefaction. For this project, approximately 6,700 soilcrete columns were constructed in a cellular pattern to an approximate depth of 40 ft. All of the soilcrete columns are 3 ft in diameter with the design unconfined compressive strength (UCS) of 150 psi."

Jan 1, 2015

By R. Burrell, N .. L. Lapp

"Except for asthma and pulmonary infections, the types of lung disease that have been of immunologic interest the longest are the various mineral pneumoconioses. Because of their chronicity, type of pathology produced, and well-known immunotoxic properties associated with the dusts inciting them, the pneumoconioses have long drawn attention to the possibility that the immune system has not only been modulated but that its effectors have possibly contributed to their pathogenesis. All of the mineral dusts reviewed here have definite immunomodulating properties and act on various cellular and molecular components of the immune system. Further, each has an immunotoxic potential to induce either hypersensitivity (as in the case of beryllium) or other types of immune injury. This article reviews the immunologic aspects of the four major occupational minerals that have an immunologic impact on the lung: asbestos (particularly chrysotile), silica or quartz, beryllium, and coal mine dust.These agents have many things in common, yet each is distinctive. Although the possibility still exists that these mineral particles can adsorb intrinsic tissue antigens or extrinsic organic antigens to their surfaces and initiate immune responses to the adsorbed antigens, only one, beryllium, can act as an antigen itself. Silica is a profound macrophage toxin and thereby exerts many effects on those factors controlled by macrophages. Asbestos has undergone the most immunologic studies resulting in a much dearer picture of how it may contribute to immunopathology. Coal mine dust is the agent about which least is known immunologically, partly because there is no such thing as purified coal mine dust or a standard by which coal mine dust can be defined. Indeed, there are studies that use only the dust from the ground coal itself, whereas other studies use the total dust collected from air samples of a working mine in the belief that other types of dusts (e.g., silica from roof bolt drilling, from sand ground on the rails by cars, and from surface drilling) contribute to the disease (Figs. 1 to 5). This properly is coal mine dust and is poorly characterized. Yet, workers exposed to these dusts share similar reactive characteristics and they may be considered collectively as well as individually."

Mar 1, 1992

By J. E. Jopling, J. R. Chenneour, E. L. Derby, S. R. Elliott

The Marquette range, on which are situated the iron mines of Mar-quette County, together with a few in Baraga County, Mich., extends from a point 10 miles southwest of Marquette westward for 30 miles. The tracts are usually a multiple of the standard 40-acre parcel, which is the smallest government subdivision of a square mile or section. About half of the mines are held in fee, these being owned by the older mining companies. Some of them date back to about 1880, and a few are as early as 1850. During the past 40 years most of the mines opened have been on leased lands, the royalty being either for a stated amount per ton or a percentage of the selling price of the ore at the lower lake ports, or the selling price on board of cars at the mine. The first merchantable body of ore discovered in the Lake Superior district was found, in 1845, at what is known as the Jackson mine, near Negaunee. This ore was hard hematite. After unprofitable attempts had been made, in 1848, to smelt it in forges, shipments were begun to lower lake ports, which increased rapidly upon the completion of the locks at Sault Ste. Marie, in 1855, and the railroad from the mines to Marquette, in 1857. Beginning with the Pioneer, in 1858, a number of small charcoal furnaces were built to smelt a part of the product. At various points in the upper and lower peninsulas, large charcoal furnaces are still making iron from the ores of the Marquette range. In connection with these furnaces are byproduct plants. As the deposits were opened up, soft ore was encountered, but for a few years this was disregaided, as only the hard ore was used. Underground mining was begun about 1880 and during the next few years the open-pit mines producing high-grade ore were exhausted. The first mines in the district were owned by the Jackson, Cleveland, Lake Superior, Lake Angeline, Champion, Iron Cliffs, Humboldt, Republic, and Michigamme companies. Many of these companies have been merged in the holdings of The Cleveland-Cliffs Iron Co., which controls most of the tonnage of the district.

Jan 1, 1925

By J. A. Arias

The oxidation kinetics of pyrite and refractory gold concentrates in acidified ferrous sulfate solutions in the presence of oxygen-sulfur dioxide gas mixtures has been studied. The effect of temperature, pulp density and gas composition were determined. The optimum oxidation rate was obtained at 80°C and 2 percent sulfur dioxide in the gas mixture. The oxidation of the sulfide minerals is attributed to the presence of ferric ions, which are continuously regenerated by the gas mixture. The objective of this study is to find a new hydrometallurgical method to render sulfidic refractory gold ores amenable to cyanization.

Jan 1, 1993

Prof. HEnRy Louis, Newcastle-upon-Tyne, Eng. (communication to the Secretary*):—I welcome Mr. Hammond's paper as an attempt to give definiteness to the best modern professional practice. Such a codification of our professiollal ethics is urgently needed, seeing how widely the views of nlining engineers direr on some of the points raised; for example, I have no hesitation in performing a class of work, as to which Mr. Hammond seems to entertain some doubts, and, on the other hand, I strongly condemn a practice which he appears to recommend. I have not the least hesitation in making reports for vendors of mining-properties, and am constantly doing so; the best justification for this practice may be found in the fact that such reports have been repeatedly accepted by buyers as giving a correct representation of the facts of the case, which is all that should be demanded from any report. On the other hand, Mr. Hammond advocates that mining engineers should take payment for their reports in shares of a company to be floated upon the basis of such reports. I hold that this is ethically wrong, as even themost honest of men is liable to be unconsciously biased under these conditions. Indeed, I go much further, and maintain that a mining engineer who reports or advises upon mining-properties should never hold any mining-shares at all, or be himself interested in any mine, and this has been my consistent practice for many years. A man who hold shares in a mine, and is called upon to report upon a neighboring property or a similar mine, can never be wholly unbiased; and even if he could be, he would always lay himself open to the suspicion that he was giving a favorable report 80 as to enhance the value of the property in which he himself is interested, or an unfavorable report so as to stifle competition. It is quite as bad for the manager of a mine or the consulting manager to be interested, because he will have access

Jan 1, 1910

By C. B. Clemmens

Accurately predicting ground control conditions before mining requires a comprehensive exploration approach including photogeologic mapping (satellite and low altitude), delta modeling and, particularly, geophysical logging. In situ properties, density; strength indices; grain size; clay content; and aquifer location, can be estimated with this inexpensive technique. Geophysical measurements can be spot-checked by field or laboratory tests on core samples and by hydrologic (pressure) testing. Each phase of drilling should be accompanied by refinement of the delta model, facilitated by log signatures. Measured properties can then be projected into geologically similar areas. A properly planned program will delineate both the "worst-case" and normal support conditions. Suspect areas can be avoided by mine layout and the mine plan can contain support contingencies for anticipated trouble spots.

Jan 1, 1985

By Stewart W. Towle

In 1989, the u.s. Bureau of Mines initiated a contract to gather engineering, operating, and environmental cost data for 1988 for 30 major foreign primary copper smelters in market economy countries. Data were collected for 29 of the designated smelters together with information on applicable environmental regulations. Materials balance data obtained were used with available data for the eight U.S. smelters to determine the approximate extent of copper smelter sulfur emission control in 1988. A broad characterization of the status of sulfur emission control regulation was made. The 37 U.S. and foreign smelters represented roughly 73.2% of world and 89.3% of market economy primary copper production in 1988. The 29 non-U.S. smelters attained 55.3% control of their input sulfur in 1988. Combined with the 90.4% control of U.S. smelters, an aggregate 63.4% sulfur control existed. Roughly 1,951,100 mt of sulfur was emitted from the 37 market economy smelters in 1988. Identifiable SO2 control regulations covered 72.4% of the 29 foreign smelters, representing 66.5% of smelting capacity. Including U.S. smelters, 78.4% of the major market economy smelters were regulated, representing 73.1 % of smelting capacity. Significant changes since 1988 that may increase sulfur emission control are noted.

Jan 1, 1993

By R. E. Hershey

1. Reserves were estimated for three coal beds: Lantana, Sewanee, and Richland. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 34 million short tons as of Januray 1, 1954. Of this total, 15 million short tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By Yap Chu-Phay

IN 1923, when the writer began his studies in metallurgy, he came upon an article by Professor Honda on the, Equilibrium Diagram of the Iron-carbon System, 1 which made a profound impression on him. What interested him most was this sentence: "In the recent diagram of the iron-carbon system, the solidus is usually shown as a curve bending considerably downward. But it can be shown by thermodynamics that if the liquidus is straight or slightly curved, the same must also be true for the solidus. Hence, in my constitutional diagram, the lower portion of the solidus is slightly bent upward." Ever since then the writer has been interested in thermodynamics, especially chemical thermodynamics. The applications of thermo-dynamics to the metallic systems have been, in the writer's opinion, sadly neglected, although we continually use the phase rule in our study of equilibria in the liquid and solid states of metallic alloys. Many investigators, among whom may be mentioned Heycock and Neville, and s Honda and his coworkers, have applied the simple Raoult-van't Hoff law of depression of freezing point, mainly to determine the heat of fusion, but no attempt has been made to investigate the applicability of the thermo-dynamic laws of solution (as opposed to the laws of solution derived from other sources) to metallic systems" showing either limited or complete solid solutions. Perhaps the reason for this neglect is that until recently there have been so few reliable data on the solidus, which is much more difficult to determine than the liquidus. The writer has under way at the present time an investigation of a number of systems, the solidi of which have been more or less reliably determined. Recently, the writer has not only shown the valid applicability of the thermodynamic laws of solution as applied to the system antimony-bismuth but has also suggested a method of attacking problems involving complete and incomplete equilibria.2 In the present paper, the same method of approach is employed. For convenience, we shall divide this paper into two parts:

Jan 1, 1931

By G. W. Luxbacher

This volume describes the use of the Penn State Mine Ventilation Simulator (PSU/MVS) to model existing mine ventilation systems and, in addition, to evaluate the effect of system modifications. Ventilation survey methods designed to insure computer input data of sufficient accuracy for simulation purposes are covered in comprehensive detail, including quantity and pressure measurement and fan performance testing. The development of input data from ventilation survey results is discussed and illustrated by the use of an actual field survey. Two programs, written in FORTRAN IV with WATFIV, are presented to calculate airway head losses from altimeter pressure measurements. An existing coal mine ventilation system is analyzed and modifications to the system are simulated and evaluated. In addition the application of the PSU/MVS to non-coal mines is briefly discussed. An extensive bibliography on ventilation surveying and simulation is included.

Jan 1, 1977

By Alfred Bodenlos

"El presente texto señala los acontecimientos geológicos en la Cordillera Negra y la deposición de travertino por las fuentes termales todavía activas al oeste de la población de Ticapampa. Los minerales fueron depositados principalmente como rellenos de fisuras, siendo cavernosos y en partes bandeados y sus temperaturas conocidas de formación varían desde baja hasta moderada, lo cual, además de su textura porosa, sugiere que están comprendidos entre las clases epitermal y mesotermal, según sistema propuesto por Lindgren. "

Sep 1, 1957

By P. A. Robbins

FAR NORTH, on the bare Arctic tundra, 11 mi. above the mouth of the Keewalik River where the latter discharges into Kotzebue Sound. several ., Eskimos garbed in parkies and muck lucks mingle with a small group of similarly clad white men. All of them shield their eyes from the white glare of the arc as a gasoline-driven arc-welding set rains molecules of metal on the break in a bull wheel, the large gear wheel which swings the boom and cab of a dragline shovel.

Jan 1, 1937

The rocks of Waihi and the surrounding district are almost entirely rhyolitic and ande5itic in character. Sedimentary rocks, with the exception of some surface deposits of clay loosely compacted conglomerate, etc., and one or two thin and broken beds of a very poor lignite, occasionally changed by igneous agencies into a bituminous coal, are almost absent. In the shafts sunk by the Waihi and Grand Junction companies outside the outcropping andesitic area of the Martha Hill, more than one old surface or lake bottom has been passed through. At these points layers of sand, consolidated volcanic mud and tuff, accompanied by numerous broken fragments of imperfectly silicified wood have been enccuntered, but these occurrences may, for the purpose of this paper, be neglected.The youngest rock of the district are rhyolites, probably of Pliocene age. At least three distinct classes of rhyolitic lava, each possessing features of unusual interest, may be made out. None of these, however, is gold-bearing. The youngest flow, a light-coloured, fine-grained rock, is remarkable owing to its enclosing at times fragments of carbonised wood, varying in size from mere specks up to quite large pieces of almost pure charcoal. Rhyolitic tuff is also met with. The rhyolites cover a large extent of nearly flat country east, south, and west of Waibi, here and there rising into barren, stony hills.Below the rhyolites, geologically speaking, but for the most part. forming hills which bound the rhyolitic plain, or rise out of it as isolated patches, come ahdesites of older...

Jan 1, 1902

By H. Dale Nichols

[The growing importance of the Sundence (Jurassic) formation an a source of oil, in the Rocky Mountain area has prompted the making of a series of porosity determinations of core samples collected. from the reservoir sands of the Lance Creek oil field, Niobrara. County, Wyo. These analyses are preliminary to a stud of fluid and energy relations in the Basal Sundance reservoir of that field, and the determinations of porosity will be used in subsequent studies requiring, calculations of the volumetric capacity of the reservoir and estimation of the reserves of oil and gas. However, the porosity characteristics an of the Sundance sands in the Lance Creek field are factory that affect the solution of many current practical problems of development and operation. Primarily for that reason but also because it is recognized that porosity values of different oil-production sands are of widespread interest throughout the industry, the results of the initial work have been presented in tabular and graphic form with no attempt to evaluate their significance as they relate to the production history of the field.]

Jan 1, 1938

By John T. Cumberlidge

The Groveland deposit, in the Upper Peninsula of Michigan, consists of an E -W trending overturned syncline of Middle Precambrian Vulcan iron formation. At Groveland, the Vulcan formation can be divided into four units or facies. The total succession may be more than 550 feet thick, and consists of a basal unit composed of a lean chemical quartzite with traces of magnetite; a non-banded, partly clastic unit characterized by the preponderance of hematite over magnetite; a transition unit of well-banded magnetite-bearing iron formation interbedded with non-banded oolitic hematite; and a well-banded magnetite-quartz silicate unit at the top of the exposed sequence. The present magnetite-hematite ratios of different units within the orebody are considered to be a primary (post-diagenetic) feature of the original sediment. Subsequent regional metamorphism has increased the grain size of the original iron oxide minerals, but did not appreciably alter the oxidation state of the original sediment.

Jan 1, 1964

By John Russell

"The South American mining community leads the world in recognition and adoption of the latest grinding mill relining technologies. Clearly this region has recognised the benefits of improved relining performance.Six of the seven RUSSELL TWIN 8 Mill Relining Systems, ordered to date, are either operating or being manufactured for South American mine sites.This paradigm shift, towards very short relining times, aims at displacing mill relining activities from the critical path of concentrator maintenance shutdown schedules.The first uses of the RUSSELL TWIN 8 Mill Relining System have seen some of the highest SAG mill new liner placement rates ever observed by RME, as would be expected with two, independent Machines working simultaneously in the one mill.The liner-replacement-rate, averaged over the whole reline, is good (27% improvement over single Machine System in the same mill) but short of full potential. This modest result can be attributed to reline crews unfamiliarity with RUSSELL TWIN 8 System operation.This paper compares a sample of conventional (single machine) RME Mill Relining System performance data with one ‘double head’ mill liner handler by others. Early performance of Escondida’s new RUSSELL TWIN 8 System performance is then compared with recent single Machine data from Escondida, immediately prior to RUSSELL TWIN 8 commissioning. RME and Escondida look to constantly improving RUSSELL TWIN 8 System performance as full operational familiarity is achieved.Also, the preparation of this paper revealed a need to develop a global industry standard for mill relining data collection. A web based platform, to develop and then distribute standardised data collection templates, is discussed in Annexure 1."

Jan 1, 2010

By W. G. Prast

Best known for its extensive bauxite and alumina exports, Jamaica also has a small but active industrial minerals sector. The island has for many years been a net exporter of small tonnages of gypsum, metallurgical-grade limestone and marble products. As bauxite and alumina earnings have declined the government of Jamaica has made extra efforts to promote growth of overseas sales of these nonmetallics. The nearby U.S. market is a natural first choice for new exports. Overview In 1984, Jamaica quarried an estimated 3.2 million cu m of marble and fill and an additional 3.5 million cu m of sand and gravel, for use in domestic construction. These amounts are in line with the production in earlier years of the 1980s but are not a factor in the export pattern and need not be considered further. Similarly, annual production of 15 million ton of silica sand for the manufacture of glass bottles is principally consumed by the domestic market.

Jan 1, 1986

By A. Brown

"The first printed report on Canada's coal resources was published in Paris in 1672(1. Written by Nicholas Denys, then Governor for France of Isle Royale (Cape Breton Island), the report dealt exclusively with the coal of the Atlantic region because little or nothing was known about the interior of North America. Clearly, also, he wrote about a resource of which much was known among the military and early settlers of that day. This early knowledge is not surprising because the presence of coal is clearly displayed in the coastal cliffs of Cape Breton as it was also, at a later date, to the first arrivals on Vancouver Island.An example of early use was that of the French garrison at Fort Louisburg in the first half of the 1700s. Still earlier, in 1643, Governor Winthrop of New England reported the receipt of a small ship load of coal from New Brunswick (2). Despite this early knowledge there was no significant development of coal mines until the 1800s. This had to await the ending of wars between the French and British factions and the growth of population. Basically, also, its development awaited the beginning of the Industrial Age. Organized coal mining began in Canada in 1825 with the formation of the General Mining Association. This British firm was the creation of a group of London jewellers which had been granted royal rights, by the British crown, to all minerals in Acadia (substantially the present Maritime Provinces). The Association took over a number of existing small mines and opened up larger operations in the Sydney coal field. Subsequently, it expanded to the mainland Nova Scotia fields at Stellarton and Springhill. The Association continued in existence as the major coal producer in Canada until 1899 when it sold its properties to the Nova Scotia Steel and Coal Company, Limited (3). This Montreal-based firm managed the coal mines as a major Canadian producer of coal until 1968 when financial problems led to the expropriation of the mines by the Government of Canada. The federal government established the Cape Breton Development Corporation to operate the larger mines on Cape Breton Island. This Crown corporation continues to be a .major producer of coal in Canada."

Jan 1, 1985

By Robert L. Grayson

An application of goal programming (GP) in evaluation of proposed purchases of major mining machinery is presented. It incorporates historical operating data compiled on mechanical delays to production time. The goal programming technique, which is an extension of integer programming, is used to maximize an objective function. The objective function combines the capital budgeting evaluation methods of net present value, payback period, profitability index, and total net earnings as goals weighted according to a management preference. The GP method gives an optimal solution to a multiple-goal problem. A sensitivity analysis is performed to determine the effect of an increased production forecast or a tightened budget on proposal selection.

Jan 1, 1982

By Lisa Steiner

Almost every process has a predecessor, and studying the predecessor helps to define needs and shortcomings to be addressed in the new design. It also suggests what information is needed by the users in order for them to be able to operate safely and effectively. The end users of a system can provide important feedback to better evaluate the current and proposed designs. When new technology is introduced into a system, mishaps may occur before it is realized that human-system interactions were not considered adequately in the design process. A systematic methodology to evaluate the causes of these injuries and to develop remedial recommendations can enhance safety. This paper illustrates how such an approach was used to assess remote machine operation in underground coal mines. The dynamic work environment of underground mining with its unpredictable geologic anomalies can result in numerous hazards. Many of these hazards, including mine roof collapse, occur near the working face where coal is being extracted. The face area is also where the most intricate interactions of people and equipment occur. For these reasons, a high priority has been placed upon minimizing hazards to the workers at the face. A remote control operation was introduced to provide a safer working distance from these hazards. As the remote control technology began to be widely used for extended cut mining operations, new issues became evident. It was essential to develop mechanisms for mines to evaluate these issues in order to predict and reduce injuries. Mining methods and equipment changes must allow for the ability of workers to adapt to changes in their dynamic mining environment. Consideration should be given to how the worker will use familiar information to make decisions in now unfamiliar situations. There will be both intended and unintended consequences [Merton, 1949]. Designers try to anticipate and eliminate surprises, but it is impossible to eliminate them all. How, then, will the new system affect the tasks to workers which are currently accustomed? As suggested below, this question may be addressed and more of the unintended outcomes predicted with a planned design process which includes strong human factors input to determine interactions and behaviors of participants.

Jan 1, 2005