Search Documents

By H. S. Fleming

My original intention was to give a full account of Southern furnaces, ores and cokes; but, owing to the difficulty of getting reliable information, I confine this paper to a general description of the ores used in, and immediately around, Chattanooga. Mr. L. S. Colyar, Manager of the Rising Fawn furnace, wrote me in answer to an inquiry as to what ores they were using, " Below I give you analyses of the mixture of ore we have been using for the past seven or eight years. We haven't a complete analysis of any ores, but I will give them to you as I have them. Attalla Soft Rising Fawn Hard Rising Fawn Red Ore. Red Ore. Soft Ore. Iron,.... 50.60 38.48 46.82 Silica,. .. 11.69 7.32 22.69 Phosphorus,. .. 1.06 .319 .350 This is a fair average of all the ores we get in this section." The following analyses of Birmingham soft ore were received from the Morris Mining Co., of that place. No. 1. NO. 2. No. 3. No. 4. Iron.....51.60 54.88 51.04 51.20 Silica,. .. 19.32 10.60 17.32 17.08 Alumina,....19 .88 1.18 Phosphorus,. ..129 .287 .116 .464 Mine No. 1, second vein, shows: iron, 46.40; alumina, 4.92; phosphorus,.212; silica, 19.60. Mine No. 1, by analyses obtained from the Mary Pratt Furnace CO., shows: Iron. Silica. Fine red ore,.49.00 18.38 Lump red ore,...54.42 17.10 Bottom vein,.50.00 21.38 Bottom vein,.41.24 13.52 A lot of this ore delivered in Chattanooga gave : iron, 53.32; alumina, 2.10; phosphorus,.529; silica, 18.03.

Jan 1, 1887

By H Jalalifar, N Aziz

In the ten years since the University of NSW proposed a pillar design methodology for bord and pillar operations, the Australian coal mining industry has changed substantially. What was primarily a bord and pillar design approach is now being applied to chain pillar design in longwall mines where the requirements are substantially different. The dimensions of chain pillars can impact on tailgate conditions (roof, rib and floor), seal performance, and surface subsidence. The status of chain pillar design practice in Australia is reviewed, with a focus on defining pillar strength, chain pillar loading, and assessing the performance of the roof/pillar/system. A new pillar strength equation is proposed for Australian coal that applies for all width/height ratios. An alternative analysis of probability of failure of chain pillars is presented.

Jan 1, 2005

By S. Gering, R. Ruiz, C. H. Calderon-Arteaga, J. Barrios

"INTRODUCTION Located in the northeast corner of Zacatecas State, Mexico, the Peñasquito Operation is comprised of the Peñasco and Chile Colorado (Brecha Azul) deposits. Open pit mining (pre-stripping) began in 2010 and full production commenced during 2011. The open pit mines feed both a sulphide concentrator (mill) and a heap leach pad. The project is owned by Goldcorp, Inc. Penasquito is a poly metallic deposit with Au, Ag, Zn and Pb being recovered as payable metals. As a consequence of lower grade ores expected with advancing mine-life Peñasquito is facing a declining metal production profile. To maximize returns and asset value plant modifications including the addition of a carbon pre-float circuit and a pyrite leach circuit to improve recovery are currently being undertaken. This carbon pre-float circuit will enable the recovery of precious and base metals from carbonaceous sediments. This material is currently being stockpiled. With the associated increase in complexity in the process circuit, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery at the Penasquito operation. The addition of the carbon pre-float circuit was also a key driver in allowing the Chile Colorado open pit to be developed. These conditions alongside Goldcorp’s drive to increase profitability, and maximize net asset value has created challenges. These challenges are numerous and are multifaceted, however the ability to accurately route materials from the ore control system is critical to site success, and some of these challenges have been overcome by the adoption and implementation of a new ore control (OC) technology. Examples of these technological innovations in the ore control program are discussed in this paper and include improvements in geo-modeling, material routing and reconciliation. Successful implementation of these elements has led to significant improvements in selectivity, performance, and data management, while reducing the variance between planning and execution, thus helping to drive overall improvement across the operation."

Jan 1, 2018

By Yosry Attia

Recent emphasis on environmental effects and costs of conventional mining processing, plus success in accelerating bacterial action, suggest that biotechnology be explored for gold ore processing. In our paper, the past experience with organisms in processing gold is reviewed. The use of microorganisms for liberation of gold from sulfide ores as a substitute for fine grinding is discussed. The possibility of accumulation of gold from solutions, such as cyanide solutions, is explored as a potential replacement for such processes, such as carbon-in-pulp or ion exchange. The improvement in engineering technology and kinetics needed to scale-up from laboratory experiments to production scale are outlined.

Jan 1, 1985

The Report on the Manufacture of Coke for the year 1880 by J. D. Weeks1 includes an historical account of the early days of coke-making that is very complete and accurate, and but little can be added to it to fully cover the period prior to 1885. The few additional references that have been found follow. The earliest suggestion found about making coke in this country is in a letter from D. M. Randolph to Harry Heth, dated August 22, 1808. Heth was then operating the mines in the Richmond, Virginia coal field and had sent Randolph to England to investigate steam engines for hoisting and pumping and other conditions in the coal industry there. The letter was written in London and said: "I shall explain to you, how, by turning Deep Run fine coal in Coak, to make great profit from what has heretofore been useless. You will do well to ascertain the price and amount of demand for this article throughout the U. States among brewers and manufacturers. I know how also to make every bushel of such fine slaty coal, fetch as much as any of the best grate coal, by turning it into Coak: and that too, after paying all expenses of the process."2 His interest was to use the slack more for domestic purposes than otherwise, probably, although what the interest of brewers would be in coke as fuel does not appear. Nothing ever came of this suggestion, and so far as known, no coal from this field was coked excepting in gas-making. The Plumpsock Iron Works, mentioned by Weeks as having used coke, was advertised for sale in June 1818.3 It was stated that stone coal was the only fuel used at the works, the pit being within 100 yards of the forge. "Three men with a horse and cart are sufficient to raise coke, and haul to the forge all the coal necessary for keeping the works in full operation." The coke, of course, was made in ricks, or heaps, and not in ovens. The first real coke oven in this country was probably built in Connellsville, the coal coming from a mine nearby on Mounts Creek. L. L. Norton operated an iron foundry and was persuaded by his foreman, one Nichols, who came from Durham, England to build a coke oven. The oven was 12 feet square, and the first coke was produced in 1833. Later

Jan 1, 1942

By David G. Thompson

There are basically two commonly used methods of drying washed coal. They are mechanical drying (sometimes called dewatering) and thermal drying. The common methods of mechanical drying are by using vibrating screens, cross flow screens, sieve screens or Vor-Siv, vacuum filters and centrifugal dryers. With thermal drying, the common types include direct fired fluid bed, rotary drum, flash or suspension, vertical tray or cascade continuous carrier or vibrating fluid bed dryers and hollow screw dryers. In the past, it has more or less been a general rule that any time the total product is being washed, both mechanical and thermal drying was required. The reason for this was that a product moisture of 3 to 4% was required and thermal drying was and is the only practical method by which this can be accomplished. With the advent of air pollution controls and the ever increasing concentration on dust elimination, a 3 to 4% moisture product is no longer practical in either the preparation plant or in the processing plants which utilize the coal. Under the new standards, it is desirable to have a product with a 6.5 to 7% surface moisture. With this moisture range, dusting, due to handling, will bc kept at a minimum.

Jan 1, 1975

By Robert C. Ellman

Lignite and subbituminous coals are utilized essentially as mined without beneficiation. Most of the present production is used to generate electric power and the major problem in this use is ash deposition on fireside surfaces. The preparation at existing mines involves principally crushing and screening operations. Blending of production from different locations within the mine is practiced in several mines to control ash composition. Drying and oil treatment for freezeproofing, of lignite are used to a limited extent during winter. Future processing may involve both washing and drying operations to alter ash composition by ion exchange and upgrade the low-rank fuels to higher heating values. Research has been initiated to determine the feasibility of such processing.

Jan 1, 1969

By J. W. Spretnak, V. Kandarpa, G. W. Powell, R. A. Erickson

Neutron-diffraction pattens were obtained at room temperature from two austenitic manganese steels, oxc wth n carbon content of 1.23 zct PC/ and the olher 0.63 wt pct. Analysis of the data showed that the curOan atols (ions) occupy tile octaheadral site. any of the cavbon is in the tetahedral site, tile concentration is too strzall lo be detecled by tzeulr-on d$facton. AS part of a long-range investigation of eutectoid decomposition, a study of the structure of austenite has been undertaken in order to characterize as best as possible the parent phase in the Fe-C system. Austenite is a solid solution of carbon atoms in fcc iron, the carbon atoms being located in interstitial positions. Of the two kinds of interstitial sites, octahedral (0, +, +) and tetrahedral (4, a, $), in this lattice, the larger octahedral sites are usually considered as the probable position of carbon. The strain energy involved in pytting a neutral carbon atom (covalent di; ameter 1.54)' into a tetrahedral site (diameter 0.56A) is considerably greater than that associated with p2tting carbon into the octahedral site (diameter 1.08A). Dayal and arkeen' observed the migration of carbon in iron under the influence of an electric field indicating tha tye carbon is ionized. pe ionic radius of C'4 is 0.15A and that of C" is 0.29. Consequently, it is conceivable that carbon ions could occupy the tetrahedral sites if one considers only the strain energy. Size considerations alone do not provide a complete explanation for the formation of the interstitial solid solutions, however. because metals such as copper, zinc, and cadmium do not appear to form interstitial solid solutions in spite of their large interstitial sites. Evidence which suggests partial ioni-zation of the carbon in austenite has also been obtained by Speiser, Spretnak, and alor who derived formu- lae relating the observed change in lattice parameter to the effective diameter of the solute atom. Assuming the carbon occupies the octahedral site. they computed the effective diameter of carbon to be 1.33A whereas the covalent diameter is 1.54A. petch5 concluded from powder X-ray diffraction experiments that carbon atoms occupy the octahedral sites. His conclusion was based on the general trend observed in the intensity of the diffraction lines as the carbon content of the austenite was increased. However, the major difficulty associated with application of X-ray diffraction to this particular problem is the relatively poor scattering power of carbon. Williamson and smallman' utilized X-ray diffraction to study the line broadening caused by the strain field about carbon atoms inferrite: these investigators concluded that at least 85 pct of the carbon in ferrite occupies the octahedral (0: 3, B) site rather than the larger

Jan 1, 1967

By Larry Southwick

This Peirce-Smith Converting Centennial symposium is celebrating the contributions of two men, William Peirce and E.A.C. Smith, in advancing technology allowing the copper industry to realize its full potential. However, theirs is representative of a larger story: New, simpler technology releasing the stranglehold of older, more complicated technology, new developments in vessel configuration and design finding alternate routes around dead ends in operability, advances in technique and concepts removing roadblocks of cycle time and capacity, and overall innovation opening up vast new reserves around the world to those companies willing to embrace those improvements. Our story is also one of personalities, stubborn smeltermen versus the innovators, those inside the industry versus those from outside. It is a story of an initial borrowing from the steel industry, but also Peirce and Smith, from the refining end of the copper business, taking the ideas of Baggaley from Pittsburgh’s steel and airbrake industry, who built on what Hollway, Manhès and David, Douglas, and others had done in smelter tests, further to compete with the previous primacy and closely held expertise of the copper smeltermen in Wales. These advances have been well recorded in photographs taken over the last 150 years. A number were submitted especially for this symposium. Many others were published in the mining and metallurgy press of the times. Several mining schools also retained copies of photos either taken during field trips, or donated to the school by alumni and operating companies. This presentation will provide a selection and discussion from these sources of “converters in action”, describing the various designs, operations and developments depicted. The focus here will be on the first roughly 60 years of copper converter development, from Bessemer’s days at the dawn of this new idea, up to and slightly past the time of initial adoption of Peirce and Smith’s designs.

Jan 1, 2009

By Clark D. Harrison

This paper compares the ash slagging potential of Illinois No. 6 Seam coal: as raw coal; as commercially cleaned coal processed in a baum-jig plant; and as coal cleaned to a reduced ash specification at the Electric Power Research Institute's Coal Cleaning Test Facility. The comparison is based on: ? ASTM ash fusibility data ? A slagging index ? Gravity fractionation analyses of critical mineral matter compounds ? Comparative pilot combustion tests. The first three grounds of comparison are laboratory data; and the final comparison involves burning approximately 15 tons of each coal at CONOCO's 1.5 MBtu/hr (440 KW) test combustor. The evidence of these .four comparisons indicates that lowering the ash specification of coal before combustion can significantly improve the ash slagging characteristics of Illinois 90. 6 Seam coal.

Jan 1, 1984

By E. H. Rose

From the more distant members and some not so distant, the plaint is often heard that they cannot justify the expense and time required to attend the AIME Annual Meeting. Almost invariably, the reason given takes this form: "I just don't see that I would get enough out of it." Often the would-be clincher is added: "Besides, the meat of it all comes out in print anyway." Not long ago, a group of us who have seldom missed a meeting in recent years fell to discussing this phenomenon, and found ourselves in emphatic agreement that anyone holding such a belief indicates by his first remark that he does not know how to attend a convention, and by his second, proves it. He is, by and large, the man who has never been there, and of him, there are many.

Jan 1, 1949

The following letter has been received from Professor P. A. Young, Head of the Department of Mining and Mineral Engineering at The University of Leeds, England. Extractive and process metallurgy The first annual TMS-AIME Extractive and Process Metallurgy Fall Meeting:1983 International Sulfide Smelting Symposium, will be held from 6th to 9th November, 1983, in San Francisco.

Jan 1, 1982

By Wallace Ralston

The East Texas area includes the northeast 38 counties of the state of Texas. It covers all, and extends beyond, the borders of what is commonly described as the East Texas Basin. It is one of the most important oil and gas-producing areas of the Mid-Continent Province. It includes four important oil fields—Van, East Texas, Cayuga and Long Lake— and the recent extension of Rodessa field into Cass County, Texas, may prove to be of major size. Four commercial gas fields are in this area— Bethany, Waskom, Cayuga and Long Lake. Up to January, 1936, all of the oil has been produced from the Upper Cretaceous formations, and most of that from the basal member, the Woodbine sand. Gas is produced from both the Upper and Lower Cretaceous formations. Development in Fields East Texas Field.—This field continued to dominate the drilling and production situation throughout the United States. There were 4036 wells completed in this field during 1935; that is, 365 more wells than were completed during 1934. Drilling activity was due to close spacing of wells and the addition of 10,000 acres to the field. The field is now drilled to a density of one well to 6½ acres, which is certainly more wells than necessary for economic production of the field. The close spacing of wells is due mostly to the type of proration, which is per well allowable based on a potential test, and does not take acreage into consideration, and also to the numerous small acreage tracts such as town lots and excess strips. The field now has 19,519 producing wells. The allowable production for the field during 1935 was 161,118,659 bbl.; estimated production, including illegal or "hot oil," was 174,200,150. The illegal production of oil gradually decreased throughout the year, until an estimated low was reached of 20,500 bbl. daily during the months of November and December. The price of oil remained at $1.00 per barrel throughout the year. As stated, about 10,000 acres were added to the field during the year, making a total of 128,000 productive acres. There is a possibility that

Jan 1, 1936

By G. H. Gronhovd

This is the final report on a research program to develop a pilot plant gasifier for slagging gasification of lignite at high pressures and to obtain process data under various operating conditions. An operable pilot plant was developed, and the test results show that lignite is well suited for the process. Tests were run at pressures from 80 to 400 psig, and the results indicated that pressure had little effect on gas composition or the material requirements per unit gas produced. Gas production rates as high as 26,000 scfh/sq ft of reactor area were obtained at 300 psig, but limitations on auxiliary equipment prevented full-capacity operation at 400 prig. In several tests lignite having a 37-percent moisture content and 2,500° F ash-fusion temperature was successfully gasified. Refractory materials were found to have a short life in contact with high-temperature slag, and a water-cooled taphole was developed. Exploratory tests with coking coal were unsuccessful.

Jan 1, 1970

By J C. Koppe, L Vieira

One common problem for blasting in iron ore mines with significant weathering is the occurrence of large blocks of hard rock mixed with softer material. This situation causes a problem for blasting design and sometimes produces large boulders of rock that require a secondary blasting, as well as excavation difficulties. To minimise this situation, geophysical techniques were used to identify the hardest material amid the weathered material. To study the problem, seismic, ground penetrating radar (GPR), electrical resistivity and induced polarisation (IP) methods were used in an intensely weathered Brazilian iron ore deposit. The methods of GPR combined with IP, resistivity and seismic showed to be effective in modelling the contrast among hard, friable materials and soil. The results were used to improve the geological model and create more favourable conditions for the subsequent blast design. The blast design based on geophysical/geological models resulted in significant improvement in the fragmentation of the iron ore. This was achieved by the adoption of a specific drilling pattern for a given geological situation. With the new specialised blasting design the formation of boulders was eliminated.CITATION:Vieira, L and Koppe, J C, 2015. Geophysical techniques applied to blasting design, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 289–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

One distinctive feature of the global mining industry approaching the twenty-first century is the worldwide commitment of mining houses to large-scale projects in developing countries. One good example is BHP's development of the Escondida copper project in Chile. The Escondida orebody was discovered in 1981 and construction began in July 1988. Mining began in December 1990 at a design capacity of 320 000 tonnes of copper contained in concentrate. Out put has grown significantly and shortly Escondida will become the largest single copper mine in the world producing copper at the rate of 800 000 tonnes per annum, including 80 000 tonnes of copper metal. Escondida provides a case study of the development and growth of a large-scale mining operation in a developing country. Key elements have been innovative financing, the management of country risk, the recruitment of an excellent workforce, the use of advanced technologies and best practice in environmental management and community relations. Escondida is one of the global mining industry's success stories in the 1990s.

Jan 1, 1996

The impact of smoothing on the definition of ore and waste boundaries using linear estimation and conditional simulation methods is discussed. The nature of transfer functions is examined including their ability to incorporate categorical data (e.g. a dominant lithology code). An Ore Block Optimization (OBO) transfer function is presented that provides a clear guide for the mining geologist. Advantages are seen in defining stockpile cut-off grades and meeting production targets such as maximizing head grade, maximizing ore tonnes or minimizing ore loss or dilution. Each of these scenarios impacts on mine profitability and grade control.

Jan 1, 1999

By Albert L. Toenges

The introduction of mechanized mining in coal mines, which has speeded loading, has emphasized the importance of efficient underground transportation systems. The purpose of this investigation is to study and analyze various systems now in use, and to derive conclusions therefrom. This report may be helpful to operators who are planning new systems of transportation or who are revising present systems to increase their efficiency. This paper is the first of a series on this subject and des¬cribes some systems of transportation `utilizing rail haulage, ACKNOWLEDGMENT The information used in preparing this report was obtained through the courtesy and cooperation of the officials of the companies whose mines were studied. The descriptions of the transportation systems at the mines included herein have been checked for accuracy, and publication of the data has been approved by the executives of the several operating companies.

Jan 1, 1940

By H. J. Wasson

WITH the close of 1932 and the third year of the depression, the activity of oil production presents, amidst the general wreckage and chaos of industrial society, a somewhat unique picture of rationalized economic effort. East Texas still dominates the contemporary horizon, but it has become, at least for the time being, a definitely known factor. With its 9500 wells it is approximately 90 per cent drilled up. So long as production control obtains, it is merely one important factor of the national oil reserve. Each succeeding month of stabilized production tends to lull the industry's fears and the menace, both actual and psychological, of this giant field becomes ever more remote.

Jan 1, 1933

By Doug Russell

Natsource: At a Glance l 160 employees l Global reach ? New York, Washington, Calgary, Ottawa, Toronto, London, Tokyo l Major Environmental Commodity Broker ? Rated as Top GHG Broker (Environmental Finance Magazine Survey, Dec. 2000 & 2001) ? Leading RECs Broker ? Large Broker of SO2, NOx l Large Energy Broker ? One of Highest Volume Gas Brokers ? Major Electricity Broker Overview l International Market l Implementing the Rate-Based Proposal l Assessment and Management of Risk from GHG Emissions Limitations

Nov 1, 2002