Search Documents

By C. R. Kuzell

IN COMPARISON with recent years 1932 has yielded much less tangible evidence of progress in copper reduction and refining. The industry has been extremely quiet, especially in the United States. Design and construction has been throttled by lack of new capital expenditures. The excess producing capacity of the whole industry and the extremely gloomy outlook for the future have made it unwise to tie up more capital except under special conditions. The plants built during the previous year have, however, been placed in operation. Older plants have been abandoned, temporarily shut down, placed on part time operating basis, or continue to operate at a low percentage of normal capacity. In the United States the Phelps Dodge Corporation at Douglas, Ariz., has completed the remodeling of the former Calumet & Arizona smelter. A new roaster and Cottrell plant chimney was completed this year. Though operations have been limited the new equipment has been found to justify all expectations. The reverberatory plant addition consists of two furnaces 26 by 107 ft. inside dimensions, with a high arch, and modern steel binding of excellent design. Natural gas fuel gives good results. One of these furnaces will treat 1000 tons of solid charge per day with a fuel consumption of approximately 3,000,000 B.t.u. per ton. The larger converters have not only yielded the expected lower costs, but have simplified operations in the converter department. One of the noticeable results is the greater cleanliness in the environment and the absence

Jan 1, 1933

By X. -G. Chen, K. Liu

Nowadays, great interests are rising on aluminum alloys for the applications at elevated temperature, driven by the automotive and aerospace industries requiring high strength, light weight and low cost engineering materials. As one of the most promising candidates, Al-Mn-Mg 3004 alloys is found to possess considerably high mechanical properties and creep resistance at elevated temperature resulted from the precipitation of a large number of thermally stable dispersoids during heat treatment. In present work, the effect of Fe contents on the evolution of microstructure as well as high temperature properties of Al-Mn-Mg 3004 alloys has been investigated. Results show that the dominant intermetallic changes from a-Al(MnFe)Si at 0.1 wt.% Fe to Al6(MnFe) at both 0.3 wt. % and 0.6 wt. % Fe. In the Fe range of 0.1 to 0.6 wt.% studied, a significant improvement on mechanical properties at elevated temperature has been observed due to the precipitation of dispersoids, and the best combination of compression strength and creep resistance at 300°C is obtained in the alloy with an intermediate Fe content (0.3 wt.%) with finest size and highest volume fraction of a-Al(MnFe)Si dispersoids. The superior properties obtained at 300°C makes 3004 alloys more promising for high temperature applications. The relationship between the Fe content and the precipitation of stable dispersoids as well as the materials properties has been discussed.

Jan 1, 2015

By John Ralston

"Interfacial chemistry plays a pivotal role in bubble-particle capture, for it controls whether or not attachment occurs. Surface heterogeneity, degree of surface hydrophobicity, bubble nucleation and related phenomena influence the stability of the aqueous wetting film between a particle and an approaching bubble. The latter must be unstable if capture is to occur. Various techniques that may be used to quantify this interfacial, chemistry-dominated behaviour, are described.The efficient capture of specific particles by rising bubbles and the delicate control of interfacial chemistry that leads to selective capture are central issues in froth flotation. For efficient capture to occur between a particle and a bubble, they must undergo a close encounter, a collision process dominated by hydrodynamics. Should this encounter bring the particle and bubble within the range of attractive forces, the intervening liquid film between the bubble and the particle will drain, leading to a critical thickness at which rupture occurs. The liquid-vapour interface then retreats over the solid particle surface until a stable wetting perimeter is established. The particle and bubble are then joined after this attachment process. The particle may only be dislodged from this state if it is supplied with sufficient kinetic energy to exceed the detachment energy in this detachment process. These various events are now well documented and may be followed using high-speed videomicroscopy (Schulze, 1984; Nguyen et al., 2001).The process of collision can now be described quantitatively for single bubbles colliding with bubbles under various flow regimes (Dai et al., 1998) and appropriate scale up is possible for multiple bubble particle collisions occurring under turbulent conditions (Pyke et al., 2002). In this paper we will be concerned with the role of interfacial chemistry and how this influences the attachment process."

Jan 1, 2003

By E. D. Gardner

A custom gold and silver plant is one that treats ores for a fee. Usually such plants are located in mining districts and treat local ores. Ores of milling grade generally can stand only moderate transportation charges. These plants are scattered throughout the West. Most plants now doing a custom business originally were built by mining companies to handle ores from their own mires. As excess mill capacity became available ores from neighboring properties were treated, vainly as an accommodation. Later, as their own ore bodies became depleted, the mills were operated entirely on a custom basis. A few plants pull ore from their own mines only when the supply of custom ore is insufficient to keep the mill operating. Some of the present custom plants were built for custom work alone. Although built originally to treat the ores of the Golden Cycle mine, the Golden Cycle plant at Colorado Springs, Colo., soon became a custom mill and has been operating successfully for many years. It is the largest gold mill in the Western States and. treats Cripple Creek ores, from which most of its tonnage still comes. The plant is equipped to treat a great variety of ores and receives shipments from a wide area. It competes with smelters in Colorado, as it has a roasting plant to prepare sulphide concentrates for treatment in its cyanide plant. Most custom mills, however, are not adapted for more than one or two kinds of ore. Gold occurs in its ores both in the metallic state (free) and locked up in sulphides. It also occurs in a few places, notably at Cripple Creek and a few other Colorado districts, as tellurides. Mien the gold occurs in the native state, the ores is said to be free-milling and can be recovered by amalgamation. Usually, however, some subsidiary treatment is required to make a satisfactory extraction. Amalgamation generally was followed by tabling in the earlier mills; at present, flotation has replaced tables at many places. As depth is reached in raining and the workings extend below the oxidized zone the character of the ore usually changes, or, as the miners say, "it gets base". Since the advent of flotation, the average recovery of gold in base ores has been improved-greatly. Cyanidation is applied to some types of both gold and silver ores. The recovery by cyanidation is in general considerably higher than by other methods in vogue and in addition has the advantage of making a finished product which can be sold directly to the mist, thus obviating smelting charges on concentrate and discounts

Jan 1, 1935

By J. P. Thomson

Magnesium alloys are steadily improving their market share as structural components especially in the transportation sector. Therefore, there is a great deal of interest from the automotive and the metal casting industry to develop viable economic casting processes for magnesium-base alloys. This paper summarizes the preliminary results on the continuing projects within CANMET-MTL on casting processes such as gravity and low-pressure casting in sand molds, permanent molds and lost foam.

Jan 1, 2004

By Dusan Ilic

Conveyor system wear of belts and transfers attribute to a significant proportion of the maintenance costs and lost productive hours when handling hard abrasive ores at high unit rates typical of the iron ore industry. The recent growth phase has seen a rapid increase in mine and export capacity, with many new and upgraded plants operating at high throughput and utilisation. Subsequently, the industry has progressed to an optimisation phase, seeking to maximise production capacity and reduce maintenance costs with minimal capital spend. To support this, a programme of modifying designs was executed to improve conveyor transfer chute and belt life, which identified a need to challenge the industry practice for specification of designs to improve the functionality of the installed equipment. While acknowledging the importance of selecting the highest wear resistant materials for the intended application, this paper investigates design criteria related to decreasing conveyor transfer and belt wear. Of focus is a shift in the manner in which designs are specified, from specifications primarily governing geometrical constraints, to those meeting technical and functional requirements aimed at producing optimum geometry for a given set of material handling parameters. An assessment of transfer design criteria is presented.

Aug 17, 2017

By Ian Orford, Ken L. Boyd

"Can the ever-increasing tonnages of ore and waste being mined today be accommodated simply by using bigger and better crushers? This paper updates the principal author’s earlier publication, “Crushing Plant Design and Layout Considerations” (SME Mineral Processing Plant Design, Practise, and Control, 2002). It reviews the latest primary crushing and large cone crusher designs. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in the material handling flowsheet from the mine to the mill, maximizing operating hours per year.INTRODUCTIONAre larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? The principal author’s previous paper in the year 2002 on ""Crushing Plant Design and Layout Considerations"" provided a detailed design and layout review for the design of primary and fine crushing (Secondary, Tertiary, Quaternary) mineral processing facilities. Some of the conclusions in this previous paper had predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications are now available.The rock size reduction process, from the mine to the selected milling process facility has not changed since man first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized into four (4) stages:• Stage 1: Mining ( Rock Breakage and Fragmentation)• Stage 2: Pre-Screening (Scalping)• Stage 3: Primary Crushing• Stage 4: Fine Crushing (Secondary, Tertiary and Quaternary; the crushers used in this stage are identified by the titles which usage has conferred on them)Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once a project's design criteria and the mine plan has been established, the actual circuit's utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments are the key stake holders in the selection of the final comminution circuit and both departments should be familiar with and contribute to the design of the circuit."

Jan 1, 2016

By Tim B. Vander Wood

Standard methods of determining clay mineral powder aspect ratios involve manual scanning electron microscopy analyses of shadowed particles in order to measure both platelet thickness and diameter. We present a method whereby the diameters of platelets are quickly determined by automated scanning electron microscopy and their images are recorded and digitally transferred to a transmission electron microscope equipped for parallel electron energy loss spectroscopy. Thickness' of platelets whose diameters are known from the previous analyses are determined by measurement of the ratio of scattered and unscattered electrons in the beam after it has been transmitted through the platelet.

Jan 1, 1995

By A. Mayton

The prolonged exposure of equipment operators to shock and whole-body vibration (WBY) is linked to cumulative back, neck, and abdominal disorders. In low-coal mines, space restrictions make seat suspensions difficult to use in isolating operators from shock and WBY. Researchers at NIOSH, Pittsburgh Research Laboratory, are responding to these issues by investigating viscoelastic foams. For the full-load case. an ergonomic seat with viscoelastic foams isolated the shuttle car operator from shock at 15Hz. Researchers used results from additional foam testing with an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 1998

By T. Shungu, N. Vermaut

The various copper-cobalt ores mined by Gecamines, together with typical plant applications and results, are briefly described. Intensive laboratory investigations have been undertaken in recent years to improve the metallurgical performances of the various concentrators. As a result of these tests, it was shown that the flotation of the siliceous oxide ores could be improved by increasing the efficiency of the palm oil collector (energetic conditioning, chemical emulsifier, petroleum sulfonate addition) and by varying the froth depth in the cells. A new flowsheet incorporating these modifications and a regrinding stage has been approved for the rehabilitation of the Kolwezi concentrator. For what affects dolomitic oxide ores, hydroxamates were tested as secondary collectors and, based on successful laboratory results, plant trials were run but failed due to excessive frothing. In other plant tests, xanthates were replaced by a xanthate- fatty acid mixture; plant trials over more than one year proved successful for copper, but not for cobalt. Mercaptans were tested as secondary collectors for the sulfides flotation from sulfide or mixed oxide-sulfide ores; laboratory results proved successful but, to date, no plant test has been run.

Jan 1, 1987

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes.

Jan 1, 1950

By H. G. Fleshman

?Wyoming bentonite? has become almost a world-wide trade mark for high quality sodium bentonite. Although bentonite is produced in more than a dozen U.S. states the largest producing area covers Wyoming and adjacent parts of Montana and South Dakota. Bentonite was originally known as Taylorite and later renamed Bentonite by Dr. Sam Knight, the State Geologist of Wyoming. The new name came from the Fort Benton shale member of the Mowry Formation. Bentonite is a clay consisting essentially of the montmorillonite group of minerals. Since bentonite has good ion exchange capabilities, various cat-ions are easily replaced. These cations are usually calcium and sodium; however, magnesium, lithium, potassium, and others can be exchanged. One way of classifying the clay is based on its swelling capacities when wet or added to water. Bentonite having sodium as the dominant exchangeable ion typically has very high swelling capacities and forms gel-like masses when added to water. Bentonite in which exchangeable calcium is more abundant than other ions has much lower swelling properties than sodium varieties.

Jan 1, 1987

Robert Schorr, San Francisco, Cal. (communication to the Secretary*):—In operatioils requiring the expenditure of fuel, it is solely a question of supplying a certain number of heat-units at certain temperature-conditions. The difficulty of controlling these temperature-conditions is mainly responsible for low efficiency, unless utilizable waste heat is carefully applied either for the pre-heating of the air necessary for combustion, or for the heating of the raw materials, or in other departments of the works to generate steam, etc. A high theoretical or thermal efficiency very often does not establish a high " commercial" efficieiicy, and this fact is responsible for apparent crude practice in many arts. Coal is still very cheap in the East, and oil sells in the West for less than anywhere else in the world. Despite these favorable conditions, I believe that the list of references given in E. C. Eckel's book,' and also the contributions of C. Naske,2 will show that Mr. Eldred's statement, that a the study of the phenomena of applied combustion has been neglected," is not justified as far as the burning of cement is concerned. I have investigated the heat-balance of a lirne-kiln ailci the commercial advantage of using generator-gas for calcination. Mr. Eldred proposes to calcine the materials in the present type of rotary kiln, gas-fired with long-flame combustion, and to Pdke the fritted calcines to a special, gas-fired clinkering-kiln, which shall embody heat-regenerators. While his state-

Jan 1, 1911

By D Cotnoir, Q Liu, D Richard, M Ourriban

The difficulty in fine particle flotation has been attributed, among other things, to a low bubble-particle collision efficiency. Many technologies have been developed which aim at increasing bubble-particle collision efficiency, either by generating micro bubbles or by enlarging particle sizes. However, commercial applications of these technologies are limited. Over the last five years COREM has been actively testing fine particle froth flotation technologies with the objective of commercialisation. Several fine particle flotation technologies, such as dissolved air flotation, electro-flotation, floc flotation, selective flocculation-flotation and carrier flotation, were tested on both single minerals and ore samples in order to identify the reasons that prevented these technologies from being used on a commercial scale. It was found that the two most noticeable factors that prevented the successful application of these technologies were: Mechanical entrainment of fine gangue minerals. This was a general problem in fine particle flotation, but was aggravated by these technologies that either generated micro bubbles or enlarged the sizes of hydrophobic particles. Oxidation of (sulfide) minerals that resulted in hydrophilic oxidation product coatings. The oxidised fine particles could not be recovered by these fine particle flotation technologies effectively. Solutions to the two problems, ie gangue entrainment and fine particle oxidation, were proposed and tested. It seems that polymeric depressants with both depression and flocculation functions could significantly reduce gangue entrainment, and hydrophilic surfaces of oxidised fine particles could be modified by high intensity conditioning or controlled sulfidisation, thus increasing the recoveries of fine valuable minerals. The improved fine valuable particle flotation and reduced fine gangue entrainment along with fine particle flotation technologies resulted in much improved flotation separation of fine particles.

Jan 1, 2005

By Susan Fredholm, Randolph Kirchain, Jeremy Gregory

"Jurisdictions across the world have struggled to create and finance systems that can effectively collect and process electronics waste (e-waste). Many different system architectures have been proposed and implemented, but it is difficult for policy-makers and system architects to compare the costs and benefits of different systems, particularly when the systems operate in different contexts. This paper presents a systematic methodology that seeks to address this challenge and uses data from several existing electronics recycling systems across the world to illustrate its implementation. The methodology characterizes three main system characteristics: architecture (e.g., financing and collection methods), context (e.g., jurisdiction population, density, and wages), and performance, both economic and materials collection. A comparison of systems in Europe and North America with different system architectures and contexts illuminates the importance of using the methodology to discern the extent to which architecture and context drive system performance.IntroductionElectronic waste (e-waste) recycling offers several environmental benefits when processing is done responsibly. The controversy around e-waste recycling systems rarely debates such benefits; rather, it focuses on the characteristics of an effective system and whether benefits outweigh costs. Historically, the costs of recycling most electronics have outweighed the value of the scrap recovered. Thus, in the absence of legislation, e-waste recycling systems have been limited to private recycling of high-value waste with minimal consumer participation. E-waste recycling systems now exist in many locations worldwide including Asia, the European Union, Canada and the United States and the amount of related legislation continues to increase. Numerous approaches have been proposed including landfill bans, extended producer responsibility (EPR) and consumer advance recovery fee (ARF) funded recycling systems."

Jan 1, 2008

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.

By Alejandro Ferrada Vergara

Most blasting techniques that are designed to improve fragmentation and subsequently improve ore work index to downstream comminution processes, apply powder or energy factor increases, either by stretching the drilling pattern (burden/spacing ratio) implementing faster initiation sequences or using more energetic explosives. The new application will move detonation parameters up, making the blasting process riskier for the surrounding boreholes, explosive column or initiation systems functioning.

Jan 1, 2016

By Ferris E. Sainsbury

As most mining companies utilize contractors rather than in-house drilling departments, it is difficult for most mining engineers to become familiar with drilling techniques This chapter will explain the various drilling options available to the mining industry through the services of a drilling contractor. It will also suggest improvements in program planning and specification writing by the mining company representatives to enable them to derive maximum benefit from the contractor.

Jan 1, 1979

The Pongkor Gold Mine employs 678 staff. The mine is owned by the Indonesian state company PT Antam Tbk and is located 100 kilometres south west of Jakarta, in Java, Indonesia. Mine and infrastructure development started in 1992 following intensive geological exploration over 15 years. First gold production was in June 1994. The mine comprises three main orebodies: Ciguha, which is nearly mined out, dips at 75¦ from surface to 150 m. Kubang Cicau, dipping at 80¦ from surface to 230 m, and averages 3.5 metres thick at a grade of 10 g/t Au and 128 g/t Ag; and Ciurug, dipping at 60¦ from surface to 300 m and averages eight metres thick at a grade of 14 g/t Au and 172 g/t Ag. Present global ore reserves are 4.6 million tons at a grade of 12.3 g/t Au and 133.6 g/t Ag. Exploration is continuing for new veins. Initial mining was by manual cut and hydraulic fill at Ciguha, followed by Kubang Cicau. In 1996, it was proposed to convert Ciurug to a mechanised cut and fill operation. Two single boom jumbos and three load-haul-dumps (LHDs) were purchased with the assistance of a gold loan from NM Rothschild and Sons. Implementation of this upgrade was delayed by both a national economic crisis and an invasion of the concession by illegal miners. It was not until May 1999 that raise bore vent rises and access drift infrastructure commenced. Major underground development started in 2000 and is continuing. Production cut and waste fill stoping started in July 2001. The change from manual to mechanised methods has required a total change in work practices and attitudes. However, the process has resulted in a production increase from 600 tpd to 1200 tpd. A three-month compliance test (a condition of the financing loan) was successfully completed, from July to September 2001, with an average production of 700 tpd at Ciurug and 500 tpd from Kubang Cicau.

Jan 1, 2002

By Stewart A. Ferguson

Location.-The property consists of eight claims (P-12339 to 12343, 12403 to 12405) in Robb township, adjoining Jamieson township on the west. A mocor road extends twenty-two miles northwest from Timmins to the mine. Acknowledgments.- The field work was done in 1940 and 1943, while the writer was employed by the Ontario Department of Mines. The Metals Reserve Company has made available information regarding the property through Messrs. W. R, Dunbar, of Hollinger Consolidated Gold Mines, and W. C. Ringsleben, of the Metals Control Board, Department of Munitions and Supply.

Jan 1, 1945